From the archive · Full text
Reader shop tip
Rick Mabeus, Winfield, Iowa
“My mobile work bench rolls easily because it’s fitted with big air-filled wheels. Lets you always have tools and a work area at your fingertips instead of having to continually walk back and forth. It’s fitted with a…
Read the complete tip →From the archive · Full text
Reader shop tip
Terry J. Glasheen, Oshkosh, Wis.
“I always keep a cheap set of wrenches on hand to reach hard-to-get bolts. I bend them, cut them down, or weld extensions onto them - whatever’s needed - without worrying about the expense.”
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Changing oil doesn’t have to be a messy job, say the manufacturers of this new mobile cart that collects drained oil and then pumps it out into a storage receptacle.
Read the complete story →From the archive · Full text
Feature story
Featured source:
After years of hard use with little need for repair, Ralph Johnson’s Bobcat 500 skid steer loader needed engine repair.
Read the complete story →From the archive · Full text
Reader shop tip
Allen Miller, Leon, Iowa
“My Deere 530 round baler came with only one twine tie tube which takes too long to tie a bale. I modified it by welding a 6-in. piece of 2-in. dia. pipe alongside the factory twine arm so…
Read the complete tip →From the archive · Full text
Reader shop tip
Frank Grant Aumsville, Ore.
“To hold a chain on a jack when needing a portable press - or to straighten out tubing - just weld a short pipe coupler to a 90° “L”. Then cut a slot in the top of the…
Read the complete tip →From the archive · Full text
Reader shop tip
Kenneth Kasten, Germantown, Wis.
“I have come up with a modification for tractor tire rims that saves a lot of aggravation but it’s important that you only do this with the tire and tube removed from the wheel. What I do is…
Read the complete tip →From the archive · Full text
Reader shop tip
Mel Selin, Camrose, Alberta
“I had trouble with the steering on a 1979 DX 110 Deutz tractor. I bought a new steering pump for $1,300 but it still wouldn’t work so I talked to the dealer. He said the control unit under…
Read the complete tip →From the archive · Full text
Reader shop tip
Richard R. Quiram, Fort Myers, Fla.
“The needles on my New Holland 570 square baler were badly grooved from plastic twine. I took them off and ground them out with a die grinder to enlarge the eyes enough so I could install stainless steel…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“Our new feederhouse caddy allows you to remove the feederhouse from a combine and work on it without having to use jacks, chains, or pry bars. It’s the safest and fastest feederhouse removal system on the market,” says…
Read the complete story →From the archive · Full text
Reader shop tip
Alan MacLean, Kingston, Ontario
“Large holes can be bored on a lathe without having to use a time-consuming face plate mounting. A 1 1/2-in. long piece of pipe, faced square, and with an inside diameter slightly larger than the outside diameter of…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Stelmarski, Chesterland, Ohio
“We sell high quality rust replacement patch parts for domestic and foreign trucks, pickups and automobiles. We use only galvaneel, zinc over baked metal, to ensure that our parts will virtually never rust. As an example, we have…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Heat-treating is a common way to make wear surfaces last longer. But have you ever heard of “cold treating”?
Read the complete story →From the archive · Full text
Feature story
Featured source:
You can crush used oil filters to a fraction of their original size with this new “economy crusher”, says Bagley Equipment, Lodi, Calif.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Jerome Thiemann used an old car brake rotor, a 5-ft. long steel pipe threaded at both ends, and a “pony pipe” clamp to make a low-cost portable light stand.
Read the complete story →From the archive · Full text
Reader shop tip
Steve Matthews, Berthoud, Colo.
Steve made a nifty adjustable welding table that mounts on a 4-in. pipe in his shop.
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Westhoff, LeMars, Iowa
Steve turned an ordinary pliers into one of the most useful tools around his farm.
Read the complete tip →From the archive · Full text
Reader shop tip
Bruce Klemm, Whitelaw, Wis.
“We decided our 1975 4366 International 4-WD drive tractor would be a lot more useful if it had a 3-pt. hitch instead of the drawbar hitch it came equipped with. However, we ran into two problems. International 3-pt’s…
Read the complete tip →From the archive · Full text
Reader shop tip
James S. Wilson, Celeste, Texas
He used a tractor rim off an old “B” Farmall to build a forge for his welding shop.
Read the complete tip →From the archive · Full text
Reader shop tip
Nick Dengler, Middletown, Ohio
“We carry the most complete line of parts for Deere 2-cylinder tractors in the U.S., and we’ve filled orders from every corner of the world. We have virtually every part (used, rebuilt, remanufactured, or newly built and improved)…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.
“Here are a few shop-built tools I can’t do without.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.
“I also built this drill press out of scrap steel, using a jack with a bad shaft. I mounted it in a channel iron and flat steel frame about 5 ft. tall. I use it for many small…
Read the complete tip →From the archive · Full text
Reader shop tip
Arne Eissner, Souris, Manitoba
“When one of the tie rod balls on the adjustable front axle on my Deere 6030 tractor wore out, I discovered that replacing it would cost me about $320. I was able to save a lot of money…
Read the complete tip →From the archive · Full text
Reader shop tip
Eugene G. Johnson, Rapid River, Mich.
“Making large holes in thick steel often re-quires the use of large, expensive power tools. A simple, inexpensive way to cut holes is to make a compass attachment for your cutting torch. Sharpen the end of a 7-in.…
Read the complete tip →From the archive · Full text
Reader shop tip
Jack Gardiner, Ilderton, Ontario
“The moldboards on my International 710 plow had holes worn through them near the center next to the shins. I found a way to keep the moldboards from wearing so that they last a lot longer - whenever…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim & Roger Koppes, Medina, Ohio
“Here’s a time-saving revision we’ve made to strap ratchets on our flatbed bale-haul-ing trailers. By welding a 1/8-in. piece of flat stock onto the end of the ratchet and cutting a 3/8-in. square hole in the center, I…
Read the complete tip →From the archive · Full text
Reader shop tip
Melvin Carlson, Buffalo, Kan.
Melvin’s come up with a slick way to convert old AC welders, ranging in size from 0 to 500 amps, to DC to reduce splatter and get more penetration with a smoother weld.
Read the complete tip →From the archive · Full text
Reader shop tip
Travis Cooper, Ill.
He made a handy shop stool that rolls on four gauge wheels off a Deere cultivator. The stool stands about 18 in. high. The frame is made from various pieces of scrap metal. Cooper likes the stool because…
Read the complete tip →From the archive · Full text
Reader shop tip
Charles Smart, Shellbrook, Sask.
Charles built a hydraulic shop press that attaches to a punch press so he could repair the housing on his 27 1/2-ft. 4153 Will Rich air seeder.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.
“When welding thin steel I use a stainless rod with A.C. power. It seems to flow without blowing a hole in the thin metal. It’s much faster than gas welding and less heat is used, presenting damage to…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Andy R. Hodges, Galax, Va.
“The electric power window on my 1985 Ford LTD would not work. A new motor would have cost $85. When I took the panel off the door I found that the plastic rollers were broken. I installed four…
Read the complete tip →From the archive · Full text
Reader shop tip
Bruce Gamble, La Feria, Texas
“I’ve found a relatively inexpensive way to re-pair worn knuckle joints on any Deere MFWD tractor. The problem is, the seals on the double U-joints that couple the two parts of the axle together cut grooves in the…
Read the complete tip →From the archive · Full text
Reader shop tip
Dale E. Nielson, Chapman, Neb.
“We’ve had good luck using a new-style plastic welder to repair cracks in plastic irrigation pipe. Seems to work well.” (Fouillard Farm Supplies Ltd., Box 524, White City, Sask., Canada S0G 5B0)
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Don Booth, Leoville, Sask.
“My shop makes repair work easier. It’s fitted with lots of plug-ins, a large engine hoist, a 5-ton floor jack, a hydraulic press, welders, and it’s heated for winter work.”
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Baldwin, Rock Rapids, Iowa
Back in the early 1960’s, before the advent of portable AC welders, Roger built a DC welder from a 32-volt generator out of a surplus WW II airplane.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Tim Beirnes, Cambridge, Ontario
“The wagon hitch on my Massey-Ferguson 124 baler was built too light and often broke. The hitch was made up of a 2-in. dia. steel pipe that slid inside a 2 1/4-in. (inside dia.) light wall sleeve and…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Tim Beirnes, Cambridge, Ontario
“We broke a knuckle on the baler’s pto shaft on a Saturday night. A new yoke would have cost about $100 and my dealer was closed for business on Sunday. I solved the problem by borrowing the pto…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
If you’ve ever thought of turning an old engine into a high-volume air compressor, you’ll be interested in the way Clayton, Ill., farmer David Buss modified a 1961 Ford car engine to compress air. Buss left three of…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Conventional steel sprockets last maybe 400 hours. Our polyurethane sprockets are proven to last easily twice as long,” says Dick Sydor, a sales representative for PCO, a Marshfield, Wis., manufacturer.
Read the complete story →From the archive · Full text
Reader shop tip
Jack Griffith, Arlington, Texas
“When I got a welder, I knew I would need a heavy- duty extension cord to power it. I bought a 100 ft. roll of 3-wire cable and plugs for each end. We just figured what size wire…
Read the complete tip →From the archive · Full text
Reader shop tip
Joe Thomas, Mattson, Miss.
“When we bent a driveshaft on a mower-condi-tioner, we decided to repair it rather than replace it. The shaft is hollow. We cut out the bent part and found a pipe in our scrap pile that just fit…
Read the complete tip →From the archive · Full text
Reader shop tip
Klaus Nielsen, Dunwoody, Ga.
The trickiest part of trying to sharpen a metal drill bit is trying to get the 118-degree tip angle so the drill will run true. Klaus re-cently pointed out in an article in Woodshop News that you can…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Lanny Hecker, Faucett, Mo.
“I came up with a handy device to check brake lights on cars and trucks when working alone. I welded a rod with a disk blade spacer on it for weight to a pair of vice grips. When…
Read the complete tip →From the archive · Full text
Reader shop tip
Matt Biggs, Chesterton, Ind.
“I made a handy bead breaker for all types of farm tires by welding a 15-in. curved chisel plow point to a used hydraulic cylinder. Then I mounted an air chuck in the end of the hydraulic cylinder…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Paul Dean, Bolton, Ontario
“When welding inside buildings, heat and fumes can be easy to remove from the welding area by installing an old furnace fan and venting it to the outside of the building. Easy to do and cheap.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Paul Dean, Bolton, Ontario
“The sweep assemblies on my IH vibra-shank chisel plow have a habit of breaking. To repair damaged units and strengthen others, I’ve found that welding a bead around the end of each assembly will solve the problem.
Read the complete tip →From the archive · Full text
Reader shop tip
Ronald H. McConnell, Brookville, Penn.
He saves money by making many of his own replacement parts.
Read the complete tip →From the archive · Full text
Reader shop tip
Wayne Bates, Emmet, Neb.
“Here’s a handy shop tool I put together years ago. I mounted an older style post vise (the type many shop men now call obsolete because they prefer swivel-type bench vises) on a fairly heavy engine flywheel. I…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
When you change the dirty oil in your tractor or combine’s engine, you probably think the job is done.
Read the complete story →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gregory Peltier, Danbury, Texas
“Another problem on the combine was tightening the reel chain. I welded a big nut to the reel motor bracket and to the side of the combine. Then I put a long bolt through both nuts. To tighten…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
James S. Wilson, Celeste, Tex.
“Here’s how I made a 360° swivel mount for my bench vise. I bolted a 3/8-in. thick piece of steel plate to the bottom of the vise and then welded a short length of pipe to the center…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
James S. Wilson, Celeste, Tex.
“I was installing wire leads to an arc welder and didn’t have any terminals on hand. Instead, I found some copper pipe about the diameter of the wire and cut off two pieces about 2 1/2 in. long.…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
If you’ve ever had problems with inaccu-rate depth control on your Deere chisel plow that was caused by failure of the walking beam axles, you’ll be interested in this new update kit offered by Dave Barnes of Barnes…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I built it to slip over the front bumper on my Dodge 3-ton grain truck to make it easier to service the engine,” says Michel Dufault, Haywood, Manitoba, about the 5-ft. long, 1-ft. wide service step he made…
Read the complete story →From the archive · Full text
Reader shop tip
Al Rens, Hull, Iowa
Here’s a simple sure-fire way to remove square keys from drive shafts.
Read the complete tip →From the archive · Full text
Reader shop tip
Clayton Knippling, Chamberlain, S. Dak.
“I converted an old gas tank stand into a scrap metal rack. Scrap metal is cut into pieces of usable length and then stacked on separate shelves I built into the stand. Long pieces go on top.”
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 5
Individual tip 4 of 5 from this reader’s published contribution.
Edwin Ruff, Moses Lake, Wash.
“To cut metal siding androofing, I just turn an old skill saw blade backwards so it runs in reverse. It works good, although it leaves a somewhat rough edge but I just put that under the overlap.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Terry Borgan, Auburn, Neb.
“One of the neatest tricks I’ve ever come across to increase life of cutting wheels on angle grinders is this. With the cutting wheels running, apply bee’s wax to both sides of the wheel. It makes a great…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Terry Borgan, Auburn, Neb.
“Also, when preparing to weld galvanized metal, especially the old high quality stuff, take your torch and using nothing but acetylene, put a thick black layer of the stuff over the surface. It drastically cuts down on the…
Read the complete tip →