Clayton Knippling
“I converted an old gas tank stand into a scrap metal rack. Scrap metal is cut into pieces of usable length and then stacked on separate shelves I built into the stand. Long pieces go on top.”
Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–31
38 selected entries · Complete text of selected entries
This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.
“I converted an old gas tank stand into a scrap metal rack. Scrap metal is cut into pieces of usable length and then stacked on separate shelves I built into the stand. Long pieces go on top.”
“I spray bright orange paint on chains, binders, etc., to make them easy to spot if they ever fall off equipment.”
“We’ve used a Red Ball monitor on our sprayer for several years and it works well. One problem with it is that after a while the monitor tubes tend to get cloudy from sitting in the sun so that it’s hard to see the balls. I discovered that diesel fuel will dissolve whatever it is that accumulates on them. They won’t be exactly like new but they’ll be a hundred times better.”
“The front universals wore out on my 6806 MFD Deutz because there was no way to grease them. New parts from a dealer would have cost more than $900. Instead, I bought U-joints at an auto parts store and then had a machine shop make eight bushings to fit the worn castings on the tractor. The four new universals and eight bushings cost just $230 and now I can grease them so it’s re-ally better than new.
“Another idea I had was making a cradle to fit my hydraulic floor jack to make it easier to change starters on cars or trucks. It’s just a short piece of channel iron with a bolt down the center that fits into the lift plate on the jack. It holds the starter up so you can put wires on and then push it up into place.”
“Parts and repairs for older Massey Ferguson combines are costly and time consuming. We’ve bought several used junk combines at auctions to use as a source of replacement gears, bearings and belts. That’s been a money-saver.”
“I’ve gotten into the habit of using small ratchet cable come-alongs to help hook up heavy 3-pt. equipment. It saves a lot of effort, and is a good safety measure.”
“I install quick-disconnect fittings on all of my grease gun hoses. They act as swivels, making it much easier to get to fittings. It also makes it easier to take the hose off the gun to save storage space.
“Some front wheel drive cars suppos-edly require machine shop service to replace the front wheel bearings. But that’s not nec-essarily true. I use a short length of pipe and large flat washers to remove and install bearings. And I’ve installed cartridge type bearings into steering knuckles using finger pressure only by first putting the bearing into the freezer to shrink it a bit. Works great.”
“I mounted an automotive air conditioning compressor on the engine in my pickup, driven by V-belt off an extra pulley on the crankshaft. I mounted an air tank under the pickup between the frame to hold air and used a water tank pressure control to activate the compressor pump clutch as needed. I set it to keep about 70 psi in the tank. Comes in handy to have air in the field whenever I need it.
“I mounted the same air setup on my combine but I also put a 30-gal. water tank on the combine. Whenever I need water, I just put a little air pressure into the tank. I ran a 1/2-in. dia. pipe to the front of the combine and also put a faucet on the water tank.
“One nice addition I made in my shop was to mount an inexpensive ceiling fan ($20) over my workbench. Keeps me cool and it also has a light.
“To cut metal siding androofing, I just turn an old skill saw blade backwards so it runs in reverse. It works good, although it leaves a somewhat rough edge but I just put that under the overlap.
“To clean out spray paint can nozzles, just take the nozzle off and squirt WD-40 through it. The squirt tube that comes with WD-40 fits right into a nozzle.”
DeJong cleans field drain tile as a sideline business.
“I’m one of only a handful of custom tile cleaners in North America. I use specially-designed equipment built in the Netherlands. My equipment consists of 800 ft. of hose, water pump and a 500 gal. tank mounted on back of my 1983 GM 1-ton truck. The rig was originally designed to mount on a tractor 3-pt. hitch, so I had to convert the pump to run off the truck’s pto. The hose is fitted with a special nozzle that has 11 jets to blow water backward and one big jet in the middle to blow forward. The 11 backward jets pull the hose through the tile. It works on tile up to 12-in. dia. It also works well for cleaning milk house drains, manure pipes, even down spouts. I charge $150 for the first hour and $50 for each hour afterward. I’m at R.R. 1, Sebringville, Ontario, Canada NOK 1XO; ph 519 393-5774.”
Keith restored a one-of-a-kind Ferguson tractor owned by Lee Mills of Kirtland, Ohio. It was an experimental 1953 model developed between the T030 and the 35, making it a sort of hybrid between the two models.
“It may have been the first tractor ever equipped with power steering,” Keith says.
“The steering column runs down through a spool that opens and closes a hydraulic valve mounted on the column when the wheel is turned. This forces fluid out one of two lines on either side of the tractor. Each side also has a fluid return line. The power steering pump mounts up front and runs off the tractor’s timing gears.”
“Moving 1,000-lb. big round bales with my early 1950’s vintage Ford 8N loader tractor equipped with old Superior front end loader used to be a lot of work. The tractor had manual steering and the weight of the bales on the front end made it next to impossible to steer.
“I solved the problem by installing power steering on the tractor. I used two junked 3-in. cylinders, one off an old IH 503 combine and the other off an old IH 403 combine. These cylinders have control valves built right into them, making them ideal for using in the power steering unit I patterned after that used on a Ford Jubilee. The cylinders anchor on each side of the tractor on radius arms down by the operator’s feet. The opposite end had a ball swivel that I drilled out so it would fit over the tractor’s tie rod end. I installed a flow control valve on the hydraulic pump driven off the crankshaft that supplies pressure for the steering and loader cylinders.
“The system works like a charm. You can almost spin the steering wheel with one finger, even when there’s a bale on the loader.”
Here’s a simple sure-fire way to remove square keys from drive shafts.
“You weld an 8 to 12-in. piece of flat iron to the key. Then you weld a second piece of flat iron at a right angle to the opposite end of the first piece. This provides a lip so you can simply tap the key straight out with a hammer. I’ve used this method for years and it works every time. It also works for well for pulling bearings.”
“One of the neatest tricks I’ve ever come across to increase life of cutting wheels on angle grinders is this. With the cutting wheels running, apply bee’s wax to both sides of the wheel. It makes a great lubricant and you can get it for little or nothing from any bee-keeper. A chunk of bee’s wax will last a long time and applying it to your grinder’s wheels will make them last three times longer. It’s a real money saver that can be used on drill bits as well.
“Also, when preparing to weld galvanized metal, especially the old high quality stuff, take your torch and using nothing but acetylene, put a thick black layer of the stuff over the surface. It drastically cuts down on the hot zinc splatters that otherwise singe your hair and skin. I don’t know why it works but it really does.”
“I converted a CCIL500 swather from an air-cooled Wisconsin engine to a water-cooled Chrysler slant six. It worked out great. The added weight stabilized the rear of the swather and fuel economy went up 30 to 40 percent. The cost was minimal.
“I took the slant six engine out of an old Case combine. I had to add an extension to the swather frame and a new rear engine plate to hold the starter and frame mounts. I machined a stud shaft for the drive pulley to mount to the rear of the crank shaft. To cut down on air movement and to protect the operator from thrown objects, I cut the rear panel of the combine and mounted it between the engine and operator. Then I fitted the gauges and engine controls to this panel.”
“I’ve made a support board for using with a lug wrench or breaker bar extension when loosening stubborn lug nuts. It slopes upward along the top edge with a series of slots so you can fit it at any height.
“A 2-liter pop bottle works great to collect oil out of ‘empty’ 1-qt. oil containers. They fit perfect in the top of the pop bottle. You’ll be surprised at how much oil you re-cover.
“I always had trouble steering my engine hoist around the shop. It rides on four caster wheels. To solve the problem, I clamped two 24-in. long pipe clamps to the upright mast to use like handlebars. Now I no longer have problems steering it around the shop. And the two clamps are always handy when I need them for other jobs.”
“You can make a handy squeeze-type oiler out of an empty yellow Heet bottle, or other similar container, and a piece of small diameter air tube of the type used on air shocks. Cut off a piece of tubing about 2 in. longer than the height of the container. Then pierce the cap with a hole slightly smaller than the outer diameter of the tube so you’ve got an airtight fit. Air pressure when you squeeze the bottle pushes oil up out of tube.
“My oiler works great to reach out-of-the-way spots on electric motors, electric fans, sprockets, etc. Lots of uses.”
“I put 55-gal. oil drums on caster wheel carts to make them easy to wheel around the shop. The drums are fitted with hand pumps and hoses long enough to make it easy to service tractors and combines. Saves a lot of steps and is a clean way to handle oil.
“One labor-saving idea we came up with to handle our 62-ft., 8-in. dia. auger was to take the hydraulic leveling motor off our Deere disk and mount it on the auger to raise and lower it. Works great for going up or down.”
He built this cutting and welding center along one wall of his farm shop. It has a grid across the top made from iron bars above a sloped catch basin below that cut-off metal falls into. A sheet metal framework around the back protects the walls of the shop, and Holsapple installed a metal hood over the top which sucks away acrid fumes as they’re generated and blows them outside.
“Here’s a tip that may save other farmers some money if they own diesel engines with glow plugs. My 1985 Ford F-250 4-WD with 170,000 miles on it and had the original glow plugs in its 6.9 IH V-8 engine. Something malfunctioned in the relay/electrical circuit and the glow plugs burned out. I replaced all eight plugs with Champion plugs bought at NAPA and also replaced the relay and other electrical switches. All eight glow plugs burned out again, so I headed off to the Ford dealer. The news was bad. The glow plugs had swelled and both heads had to be taken off the engine. After 6 months, Champion finally covered the cost of the repair and admitted that they have bad plugs on the market. I had to threaten to sue and discovered through the legal process that they had nearly 20 cases like mine that they were paying off. This happened in Novem-ber 1995 and as far as I know, there has been no attempt to notify NAPA suppliers to replace the bad lots. So buyers beware.”
“With so many different sizes of oil filters, you need to keep a variety of filter wrenches around to handle them. To make an easily adjustable wrench, cut a 3/4-in. wide strip of cardboard off the box the filter came in and line the inside of the filter wrench. A too-large wrench with cardboard inside will sometimes snug up tight enough to break a filter loose. You could make a variety of size adjustments from sheet metal.”
“The locking collar came loose from a bearing allowing it to ruin the shaft. Rather than welding or replacing the shaft, I relocated the bearing by using large nuts as spacers. This moved the bearing onto an unworn area of the shaft.”
“I put 2-in. wide strips of industrial velcro along the top rail on each side of the bed of my Ford F-150 pickup. Then I put some under my cross-mount toolbox which holds the toolbox in position anywhere on the bed. I also apply small square patches of velcro to my tools which allows me to set them anywhere on top of the bed rail when I’m working. I even use the velcro patches on back of my cellular phone.
“Industrial velcro works well for a lot of things and has a thousand different uses.”
“I use my old New Holland 850 round baler to make about 600 bales a year. The roller chains wear out fast on the floor. I’ve had to replace the baler’s seven sets of chains twice, at a cost of about $100 per chain. I solved the problem by cutting old sicklebars into 3-ft. lengths and then welding them to the center of the floor slides. The chain now rides on top of the bars.
“The cutterbars are 3/16 in. thick and 1/ 2 in. wide. The chain is a little wider than the cutterbar so only the rollers ride on the bar which reduces friction - and wear - on the chain. Saves wear and tear on both the chains and slides. I made the conversion three years ago and haven’t had to replace any chains or slides.”
“We put on a 40 by 60-ft. addition with 16-ft. of clearance in 1992 so we could pull combines inside to work on them,” explains Roger.
“The extra ceiling height also allowed us to set up a handy storage area above our 10 by 12-ft. office, which we built in one corner of the addition.”
They built four 32-in. wide heavy-duty shelving units designed to hold a variety of parts. Access is gained by climbing a ladder to the loft. They hold parts for combines and tractors.
The Elliotts built a hydraulic hose center where they make their own hose. They built a 7 1/2-ft. tall by 2-ft. wide stand out of 2-in. box tubing. It’s fitted with four wood reels holding four different types of hose. A homemade cut-off machine mounts on the left side of the stand. It’s powered by a 1/3 hp electric motor and uses a worn out blade off their Makita chop saw as a cutter. A Weather Head collar crimp they bought at a sale for $140 quick-taches to the right side of the stand. It handles collars up to 3/4-in. in dia. and is portable so they can take it to the field.
Another improvement the Elliotts made is a pair of extension cords suspended from the ceiling. One is a 110-volt cable fitted with a standard 3-prong plug and the other is a 220-volt cable fitted with a 50-amp plug to run their Mig welder and plasma cutter. The 50-ft. cords are wound in 8-ft. coils that hang from iron rings that slide back and forth loosely on a 9 ga. steel wire about 1 in. below the ceiling.
Roland Schild, Greenfield, Ill., got the idea for this pipe bender after seeing one in a machine shop.
It consists of a couple of Y-shaped metal frames made from heavy strap iron joined at a center hinge point by a heavy pin that can be fitted with different size belt pulleys that do the bending. Schild simply switches pulleys depending on what size bend is needed.
A pair of heavy bolts are inserted on either side of the pulley. A series of holes along the frame lets you reposition them as needed to make various bends. The pipe or rod to be bent is laid alongside the bolts, and then the frame is pulled straight so the pulley moves inward.
Schild mounted the bender on a piece of I-beam mounted solid on a metal door post. The bender handles pipe or rod up to 1/2 in. dia.
Contact: FARM SHOW Followup, Roland Schild, Rt. 1, Box 172, Greenfield, Ill. 62642 (ph 217 363-2150).
You can get a firm grip on anything from the smallest pipes to the biggest oil filters with this industrial strength clamping tool from New Zealand that’s just being introduced in the U.S.
The “Boa-Constrictor” consists of a heavy-duty 9-in. long plastic handle that’s equipped with an oil and solvent resistant reinforced rubber strap that loops and tightens around whatever you’re gripping. With a tensile strength of 4,250 psi, it’s adjustable to fit anything from small pipes or jar lids up to 9-in. dia. oil filters.
Sells for $16.50 plus $3.50 S&H. Contact: FARM SHOW Followup, Steward Enterprises, 931 Main St., Manson, Iowa 50563 (ph 800 646-3816 or 712 469-3816; fax 2668).