Harold Fratzke
“I made a portable hydraulic press that can be used with any hydraulic jack.
Read the complete tip →2159 shop tips and stories · page 13 of 36, newest issues first.
“I made a portable hydraulic press that can be used with any hydraulic jack.
Read the complete tip →Paul Tierney needed a ladder to get up to the loft above his shop but he didn’t want to take up valuable floor space. So he made this “easy up” ladder that’s easy to raise and lower when…
Read the complete story →“I used a metal-clad door, a wheelbarrow wheel, and table leg to make this portable workbench.
Read the complete tip →“The gearbox and shaft wore out on my Aeromotor windmill. To get the windmill running again I ‘repurposed’ the front wheel, spindle, and kingpin assembly off a 1961 GM 1 1/2-ton pickup. I welded them to a length…
Read the complete tip →Need a wider or narrower wheel rim? FTC Enterprises can build any rim to specs whether it’s for agriculture, forestry, mining or any other off road tires. Purchased in 2012 by Ron and Jennifer Barlow of Francesville, Ind.,…
Read the complete story →With his home-built gas-powered battery charger, Robert Hanke can charge a dead battery anywhere – quickly and inexpensively. The Amsterdam, N.Y., welder built his first prototypes out of lawn mower engines and car alternators to charge batteries for…
Read the complete story →“Our new lift for high-clearance sprayers works great for changing tires and doing other maintenance work. It’s the safest jack system on the market for sprayers,” says Dan Waldner, RockPort Welding, Magrath, Alta. The sprayer lift is designed…
Read the complete story →Kelly Tidwell is a world champion drag racer who’s been working on engines for more than 50 years. Today he’s head of research and development for Pure Power!, the company he co-founded in the late 1980’s to produce…
Read the complete story →Michael Buckman’s WindMaker is a welding helmet that keeps you cool, lights up your work area, and even blows away dust and smoke. It may look like something out of a Star Wars movie, but Buckman says it…
Read the complete story →Paul Citoli likes to think of RubberizeItΤΜ as duct tape in a can. There seems to be no end to the uses customers come up with for the coating that repairs leaks, prevents rotting and corrosion, and adheres…
Read the complete story →Leonard Wulf’s 1973 Model 371 Bobcat looks like new and runs better than new since he converted it to a 20 hp Honda V-Twin engine. The old 13 hp Kohler engine was underpowered to begin with and about…
Read the complete story →“I made a wheeled bucket stand for a local auto garage. It’s designed to support a 5-gal. bucket of fluid 3 1/2 ft. off the floor, which makes pumping fluid into gearcases a much easier job when the…
Read the complete tip →“I couldn’t find wheel weights for my Ford 4000 tractor, and I didn’t want to fill the tires with fluid. Instead, I found some bar bell weights that were the right size and welded an 18-in. length of…
Read the complete tip →“My septic tank is more than 30 years old, and I was worried the tank would soon rust out and fail. I didn’t want to spend thousands of dollars to replace it. Also, according to the law here…
Read the complete tip →“Over the years I’ve used JB Weld to repair many items, most recently a cellphone antenna that broke off from the case. I’ve also used JB Weld to repair a plastic wand that broke on a pump-up sprayer,…
Read the complete tip →“I use my leaf blower constantly in the shop to dry spills, sweep in hard-to-reach places, clean out combines and tractor cabs, blow dirt off clothing, dry paint and even to discourage stray cats and other varmints that…
Read the complete tip →“Here’s a quick, simple way to air up tubeless tires. Jack the wheel up to clear the ground. Wrap a loop of steel cable on a come-along around the tire and through a heavy-duty washer. Hook both ends…
Read the complete tip →“I often use a squirt of ether to get older engines started. I’ve found that warm ether ignites much better than cold. Makes a lot of difference. Engine just comes alive right away. Cold ether is more caustic…
Read the complete tip →“I used Deere baler belting to make a loader-mounted sling. Works great for maneuvering vehicles up onto my service rack. It’s similar to the slings found on old auto wreckers and is built strong – it’ll lift a…
Read the complete tip →“I mounted an old motorhome generator on a homemade wheeled cart to make a portable power unit. The generator is bolted to an angle iron frame with a metal loop on top, allowing me to lift it into…
Read the complete tip →“I made a dumpster out of an old fuel tank. It stands on wood blocks and I hinged the top 1/4 of the tank, putting a handle to lift it. Metal rails tack-welded to to top edge reinforce…
Read the complete tip →“To make a universal wheel wrench, simply weld a 1/2-in. socket drive to one end of the wrench. Comes in handy for working on all kinds of farm machinery and wagons. Of course, the idea works with any…
Read the complete tip →“I was doing a job where I needed both ends of my flarenut wrench at once. Buying another wrench would have cost $19. So I just cut the wrench in two and then slid pieces of steel tubing…
Read the complete tip →“I made this welding cart for my Lincoln Mig welder. I bought a surplus 2-wheeled tank cart for $26 and added two rolled rings made from tubing to hold the gas cylinder. Then I made supports for the…
Read the complete tip →Marv Rubingh converted his 23-ft. tall, 62-ft. dia. Slurrystore into a shop. Built in 1979, it was still structurally sound. Rubingh started thinking about converting it even before he stopped using it for manure storage.
Read the complete story →“It’s ridiculously powerful,” says David Stern, at Metropolitan Vacuum Cleaner Company, Inc., about the Vac ‘N’ Blo PRO system.
Read the complete story →Strictly Diesel has the answer to fuel line problems with older Ford Powerstroke engines. The company makes and markets the “Driven Diesel Regulated Return” fuel system kit that helps the engine run better and components last longer.
Read the complete story →Rod Gaffrey keeps busy doing every kind of Babbitt replacement, from tiny bearings for rods weighing a few ounces to rods that are 3 ft. long and weigh 75 lbs. He has done work on rare one-of-a-kind antique…
Read the complete story →Minnesota farmer Dennis Skaro says, “When metal augers have excessive wear, they need to be repaired or replaced or they’ll damage grain and cost you a bunch of money.” That’s why Skaro likes Princeton Flighting, an Illinois company…
Read the complete story →“I wanted to lift my mower to clean the deck and do other maintenance,” says Adrian Flath of Evans Mills, N.Y.
Read the complete story →“A bearing went out on a tractor front hub, chewing up the area that holds the seal. I couldn’t find a new part for that and I needed the tractor right away, so I installed new bearings and…
Read the complete tip →“I use an old refrigerator to store welding rod. I discounted the light switch on the door so the light stays on, keeping the rods dry inside.”
Read the complete tip →“My Ford 3930 had an oil filter under the left footrest that was exposed so it could get damaged. I welded a shield under the filter and also made a low step on the shield to make it…
Read the complete tip →“Here’s how I built an electric starter for my Farmall F-12 tractor. The ring gear is from a Ford Taurus and the starter is a Ford marine starter, which I used because it turns in the same direction…
Read the complete tip →This company’s Tractor Tool Tray is designed for IH tractor models H through 1568. The tray snaps onto the tractor rail to keep tools at your fingertips. It measures 22 in. long by 10 in. wide and comes…
Read the complete tip →“I came up with an easy way to carry sockets to a job site. I screwed 3 socket-holding metal strips onto a 2-ft. long, 4-in. wide piece of kitchen countertop. I keep a 6 and 12-point socket next…
Read the complete tip →“I converted a stationary 3-jaw lathe chuck into a portable model by mounting the lathe chuck on a round stand made from 1/2-in. thick steel. At the center of the stand I welded a big pipe that screws…
Read the complete tip →“My 2001 Ford Sport truck developed a vacuum leak, which caused the ‘service engine’ light to come on. The usual way to find a vacuum leak is to spray the engine with carburetor cleaner or spray WD-40 around…
Read the complete tip →“My dad Kenny and I own a standing seam metal roofing business, and we get steel coils on pallets.
Read the complete tip →“Recently I had to remove the fan clutch on my 1997 Dodge diesel pickup. The nut is a 36 mm size, but all my bigger wrenches are SAE sizes. A 1 1/4-in. SAE wrench was slightly too small,…
Read the complete tip →Even a crowded garage, shop or work area has room for a CNC plasma cutting table if it’s a vertical unit from BurnTables. The full-size table takes up only a 26-in. strip of floor space, yet handles up…
Read the complete story →Using only water and glass, the Dustless Blaster from MMLJ Manufacturing can strip a car in about two hours. It can clean graffiti off a wall or remove paint from a motorcycle fender. The combination works on steel,…
Read the complete story →Dan Grasser gets the most use he can out of his shop thanks to his big lift platform. It allows him to store items as large as a Model A Ford on the shop’s second level.
Read the complete story →“The control valves on cutting torches wear smooth as they get older, which makes them slippery and therefore harder to turn especially if you’re wearing greasy gloves. To solve the problem I converted the round valve on my…
Read the complete tip →“Here’s something scary that happened in my shop. The abrasive wheel on my shop grinder exploded. Part of it veered off the tool’s guard shield with such force that it stuck in my shop door. I still haven’t…
Read the complete tip →“I save time when changing chisel points by first tack welding the head of each bolt to the front of each chisel point. That way, when I put the impact wrench on the nut behind the shank, the…
Read the complete tip →“Finding good used rims for older tractors can be quite a challenge. When I needed a set for the front of my little Allis tractor I couldn’t see paying $70 or more for new ones. I found some…
Read the complete tip →“One of the most useful tools in my shop is a wire wheel buffer I made from a 1⁄2 hp electric motor and a 6-in. dia. wire wheel. I use it to buff rust off metal parts, and…
Read the complete tip →“I had a problem with twine wrapping around the rotor on our bale processor. I first tried using a hot iron to cut through the twine to get it off. But that won’t work on bales wrapped with…
Read the complete tip →“When the gearbox stripped on my Kawasaki Mule utility vehicle, I bought new gears and a shim kit in order to repair it. However, none of the spacers in the kit was the right size. Some were too…
Read the complete tip →“Here’s a modification I make to all my vice grips pliers to make them easier to unlock. I weld a short piece of metal rod to the locking lever so it extends out the end. Even if you…
Read the complete tip →“If you have a wood miter saw that you don’t use a lot, you can easily convert it to a metal chop saw. Just take off the dust bag and replace the original miter saw blade with a…
Read the complete tip →“I recently came up with this homemade repair tool that makes it easier to remove the blade bar from the gearbox on a bush hog mower,” says Chad Travis, Drasco, Ark.
Read the complete story →Instead of using an electric motor to pump solvent, this new portable parts washer uses your existing air compressor.
Read the complete story →You can dress up an old Farmall with these shiny new “restoration quality” mufflers, says Steiner Tractor Parts, Inc. Mufflers are available for Farmall models made from 1939 to 1963 and are available in 2 different styles: aluminized…
Read the complete story →Tim Steele found a good sideline business cleaning engines and other metal parts with his bead blaster. He uses #80 glass beads to remove rust, oxidation and corrosion without damaging the metal.
Read the complete story →Do you have a truck with too much play in the steering from rough roads and off-road travel? You can fix the problem with heavy-duty steering components from Borgeson Universal Co. The company offers bolt-in replacement assemblies for…
Read the complete story →Old tractor seats make nifty low-cost rolling shop chairs, says Verne Schlueter, Arlington, Minn., who mounted the seat and battery box off an old Deere tractor on a set of swivel caster wheels.
Read the complete story →He set up a temporary hanging storage box that he can raise or lower as needed. It measures 4 by 6 ft. and hangs from the ceiling on four flat steel bars. The bars pivot freely on bolts…
Read the complete tip →“I removed the magnet from an old CB antenna and used JB Weld to attach it to the bottom of a pump oil can. Lets me stick the oil can to the side of any equipment I’m working…
Read the complete tip →