Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 21, No. 3 (1997)

Vol. 21, No. 3 (1997)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–32

42 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Bryan Parker

Bryan Parker, Jerome, Mo.

Bryan sells kits that convert any Caterpillar engine equipped with a pony motor to electric start.

“The trouble with those old pony motors is that they’re expensive to repair, providing you can even find someone willing to work on them. I’ve been selling these kits, which are available for both 12 and 24-volt electric systems, for four years. They install in as little as a couple hours or as much as a half day depending on the machine. The cost is as little as $575 or as much as $800 depending on which options you choose with the kit.”

Contact: FARM SHOW Followup, Bryan Parker, 22775 Pearl St., Jerome, Mo. 65529 (ph 573 762-2280).

From the archive · Full text
Reader shop tip

Robert Strommen

Robert Strommen, New England, N. Dak.

“I converted the head gate on my squeeze chute to one-man operation with a few odds and ends. It saves a lot of time and labor when working cattle.

“I drilled a hole in the end of the head gate closing lever and screwed in a hook. I attached one end of a 1 1/4-in. dia., 2-ft. long door spring to the hook and wired the other end to the bottom of the chute’s frame. I adjust the tension on the spring by feel. I prop a 3 1/2-ft. long, 1/2-in. dia. pipe underneath the closing lever on top of a 6 in. sq. piece of 2 by 6. I tied a piece of rope around the pipe and ran it back to the rear of the squeeze chute. By simply pulling the rope, I’m able to activate the head gate closing lever myself. It makes handling cattle a one-man job instead of a two-man job. The only real expense was $3 or $4 for the door spring.”

From the archive · Full text
Reader shop tip

Dan Gingell

Dan Gingell, Lapeer, Mich.

If you’ve seen the tractor repair videos FARM SHOW sells, you’re already familiar with Dan’s work on older tractors. He says he’s also had a lot of interest in his method of boosting power on later model Deere 4020 diesels. He increases horsepower from 90 to as much as 150 so the repowered rigs are roughly equivalent to a 4440.

“We first install a turbocharger on the 4020. I use only M&W T-34 turbocharger kits because of the unit’s reliability and the company’s reputation for customer service.

These kits can be installed on any Deere 4020, Serial No. 250,000 or higher, which indicates the tractor has the C.A.V. fuel pump for which this kit is designed. You have to remove the original exhaust manifold to install the kit, a simple procedure if you follow the instructions provided.

“If you go by the book, you’ll have no trouble attaining a 20 to 30 percent increase in power, up to about 125 hp. Installation takes as little as a half hour.

“If you want to spend another half-day of very careful fuel pump adjustment, you can coax even more power out of the unit, although you’ll void the warranty on the unit by doing so. However, we’ve discovered that the 4020 can easily handle the increased power placed on it by this method.

“First, follow the company’s guidelines on adjusting the fuel pump. Instead of tightening or loosening the screw opposite the notch in the fuel adjustment ring 1/16 of an inch, you can actually turn it closer to 1/8 of an inch to get a boost in power of up to 150 hp. That takes some doing and very close attention to how black the exhaust smoke is. If smoke is really black, you’ll have to back down the adjustment screw a bit.

“A word of caution: Installing the kit and making this fuel pump adjustment puts a good deal of additional stress on the rear end of the tractor so don’t go out, put on duals and expect to pull huge loads you couldn’t before. If you do, you’ll simply tear up the ring and pinion gear. But if you just use the tractor the way you did before, you’ll enjoy the extra power and ease of handling without doing any damage.”

M&W turbo kits retail for $1,760. For the dealer nearest you, contact: Herschel-Adams, 1301 North 14th St., Indianola, Iowa 50125 (ph 800 247-2167 or 515 961-7481).

From the archive · Full text
Reader shop tip

Ward Maude

Ward Maude, Caputa, S. Dak.

“I re-duced the four lower speeds on my 12-speed drill press by more than half, allowing me to use bigger drill bits and keeping me from burning up bits so fast.

“Instead of turning at about 150 rpm’s, I estimate it now runs at around 50 rpm’s, so I can use bits up to 1 1/4-in. in dia.

“I made a short shaft and mounted it on top of the motor cone pulley and put a 1 1/2 to 2-in. V-pulley on top of the cone drive pulley. I mounted a hub on top of the cone pulley and mounted a 5 1/2 to 6-in. V-pul-ley on that to reduce center pulley speed. I used a longer belt for the speed reducer.

“I had to move the hood over about 1/2 in. in order to close it over the pulleys. We’ve used the drill press like this for several years and like it so much we don’t even bother to change belts for switching back to the original, higher speeds anymore.”

From the archive · Full text
Reader shop tip

David Baade

David Baade, Victoria, B.C.

An Arctic acoustic researcher with the Canadian government, David knows too well the rav-ages sub-zero weather wreaks on cordless power drills.

“At 40 degrees below zero, you can hardly put in one screw before they need recharging. To make our cordless drills more reliable in cold weather, we convert them to run off remote car or truck batteries. We use Black & Decker drills, but this will work on any 12-volt drill. You cut apart the battery pack that comes with the drill, dispose of the batteries, and solder wires from one end of a 20-ft., low temperature-rated cable to the terminals. Then, pour the bottom of the battery pack full of epoxy to help hold the cable in place and reassemble the battery pack applying resin to the seams. Use alligator clips to connect the cable to a truck or car battery. You can work all day in even the coldest weather without running short on power and having to recharge your drill. The only expense is approximately $1 per ft. for the cable.”

From the archive · Full text
Reader shop tip

Richard Gingerich

Richard Gingerich, Augres, Mich.

“When replacing U-joints the needle bearings sometimes slip out of place or fall out. To get them back into place in the cup of the U-joint, I simply put a dab of wheel bearing grease on a screwdriver, pick the needle bearings up one by one and apply the grease, then put the bearings back in place. The extra grease keeps the bearings in place as I put them back in. Works a lot faster than using a finger and can be done on any equipment with U-joints such as pto shafts and drive shafts on vehicles.”

From the archive · Full text
Reader shop tip

Dale Spoerl

Dale Spoerl, Elizabeth, Ill.

“When the brakes on my International 560 tractor wore out I came up with a quick, inexpensive way to solve the problem - I made a stainless steel shim that takes up the wear in the brake bands. The brake drum has three bands that hold the discs in place and keep them centered. The bands are about 3/4 in. wide and stand about 1 1/2 in. outside the housing. The lower band was wearing especially bad. Whenever I put the brakes on they grabbed hard and sometimes wouldn’t release unless I backed up.

“I made the shim by using a special tool to bend a .035 thick section of stainless steel into a U-shape, then clamped the shim onto the bottom band so that it can’t move back and forth. I didn’t weld the shim in place because I wasn’t really sure that the idea would work. However, I installed the shims on the brakes of two different tractors and haven’t had any problems with either of them.”

From the archive · Full text
Reader shop tip

Jack Griffith

Jack Griffith, Arlington, Texas

“I also made ramp ends to fit 2 by 8’s for loading equipment onto a pickup or flatbed. I used pieces of 6-in. wide, 1/4-in. thick steel plate. I heated the plates and bent them in the middle, then drilled three holes in one end.”

From the archive · Full text
Reader shop tip

Steve McDermott

Steve McDermott, Epworth, Iowa

Steve mounted caster wheels on a portable welding table so that he can easily roll it around the shop wherever it’s needed. The frame and legs of the table are made from heavy angle iron, with X-braces on the ends made from strap iron. The top of the table is a piece of plate steel. A handle on one side of the table makes it easy to move around.

From the archive · Full text
Reader shop tip 1 of 2

James D. Vaughn

Individual tip 1 of 2 from this reader’s published contribution.
James D. Vaughn, Lyles, Tenn.

“To unstop grease fittings on your equipment, take out the fitting and squirt carburetor cleaner in it and let it set a minute. Then wipe it out and reinstall it. Really works good.

From the archive · Full text
Reader shop tip 2 of 2

James D. Vaughn

Individual tip 2 of 2 from this reader’s published contribution.
James D. Vaughn, Lyles, Tenn.

“Here’s an easy way to make a tire harrow for leveling out manure on pastures in the spring. I also use it to cover broadcast seed. I use six 20-in. truck tires hooked together with cable and eye bolts. I put one tire in front, two in the second row, and three in back. I cut holes in the tires and run cable through and fasten them with cable clamps. I attach a small chain to the tire in front and pull with the drawbar.”

From the archive · Full text
Reader shop tip

Adam Kool

Adam Kool, Moravia, Iowa

“I made a boom for my Miller 250 welder that makes it a lot easier to use around the shop. The welder mounts on a rolling table with drawers to hold tools. I mounted the wire spool from the welder on the 6-ft. boom, which swivels 360° and is made out of 2-in. sq. tubing. It’ll raise up over a 12 ft. high wagon or go down to 3 ft. high off the ground. I removed the wire feed mechanism from the side of the welder and mounted it on the end of the boom. The gas valve is also on the end of the boom.”

From the archive · Full text
Reader shop tip 1 of 2

Francis Deters

Individual tip 1 of 2 from this reader’s published contribution.
Francis Deters, Seneca, Kan.

“I fill up temperature gauges on older model tractors with light oil to keep them from seiz-ing up. Just drill a hole in the top, pour the oil in, and then put in a small sheet metal screw. You can only do this on mechanical gauges, not electrical ones.

From the archive · Full text
Reader shop tip 2 of 2

Francis Deters

Individual tip 2 of 2 from this reader’s published contribution.
Francis Deters, Seneca, Kan.

“I think the tie rod ball ends on 06 and 56 Series IH tractors were designed so they would wear out two or three times during the life of the tractor. I throw the ball ends away and make my own using a grade 5 bolt and 3 in. of triple strength pipe and 1/2-in. plate steel. Works great and lasts.”

From the archive · Full text
Reader shop tip 1 of 2

Robert D. Newton

Individual tip 1 of 2 from this reader’s published contribution.
Robert D. Newton, Dexter City, Ohio

I made an overhead crane for my shop using a hay carrier originally designed to handle used hay. I hung a 1-ton chain hoist in place of the old hay fork. I use it to load heavy equipment onto trucks.

From the archive · Full text
Reader shop tip 2 of 2

Robert D. Newton

Individual tip 2 of 2 from this reader’s published contribution.
Robert D. Newton, Dexter City, Ohio

“I made a 24 by 40-ft. 3-stall garage out of salvaged electric poles and a salvaged wood silo. All I bought were rafter trusses and steel siding. Old wood stave silos often have a lot of good lumber in them for framing. Many are cypress or redwood.”

From the archive · Full text
Reader shop tip

Rick Robinson

Rick Robinson, Fairfield, Iowa

“I wired up a 12-volt magnetic light with a 6-pin trailer plug for use with my pickup. Gives me a handy auxiliary light for night repair work, hooking up trailers, or for seeing behind when plowing snow with a pickup blade.”

From the archive · Full text
Reader shop tip

John E. Schwartz, Jr.

John E. Schwartz, Jr., Rowena, Texas

“When fuel or hydraulic lines rupture on one of my tractors, I use common copper tubing and compression fittings to make the repair. Saves a lot of time when you are in a hurry.”

From the archive · Full text
Reader shop tip

William L. Swan

William L. Swan, Tampico, Ill.

“I put remote lube lines on the rear steering cylinders on my Steiger tractor and also on the steerable front axle. Now I don’t have to crawl under the tractor to grease them.”

From the archive · Full text
Reader shop tip 1 of 3

Loren Konda

Individual tip 1 of 3 from this reader’s published contribution.
Loren Konda, New Effington, S. Dak.

“The old gas LUC Deere combine engine on our home-built log splitter has a cracked block. We don’t use it enough to justify buying a new one so I put diesel fuel in the cooling system and installed a set of 2-cycle engine spark plugs. They fit snugly enough to burn the diesel fuel that leaks into the cylinders.”

From the archive · Full text
Reader shop tip 2 of 3

Loren Konda

Individual tip 2 of 3 from this reader’s published contribution.
Loren Konda, New Effington, S. Dak.

“When joining a couple wires where it’s too hard to get tape around them, I just solder the wires together and coat them with silicon or liquid plastic. Works great.

From the archive · Full text
Reader shop tip 3 of 3

Loren Konda

Individual tip 3 of 3 from this reader’s published contribution.
Loren Konda, New Effington, S. Dak.

“I put an upstairs loft in our shop that’s easy to heat in winter. I put a grate in the floor of the loft right above the woodstove downstairs so heat from below gets into the loft. It stays 65 to 70°. When working on small engines or other small projects, I work upstairs.”

From the archive · Full text
Reader shop tip

Terry J. Glasheen

Terry J. Glasheen, Oshkosh, Wis.

“I always keep a cheap set of wrenches on hand to reach hard-to-get bolts. I bend them, cut them down, or weld extensions onto them - whatever’s needed - without worrying about the expense.”

From the archive · Full text
Reader shop tip

Jerry Miles

Jerry Miles, Spearfish, S.Dak.

“I make handy hose hangers from 5-gal. plastic pails with lids on them. First I cut away about 2/3 of the lid with a saber saw. Then I screw the bottom of the bucket to a 2 by 2-ft. piece of 3/4-in. plywood. You have to use big washers on the screws or you can cut out a round piece of plywood and put it in the bottom of the bucket and screw through that. Next, I hang the plywood on the wall with the bucket facing out. It works great to hold cords and hoses and you can put small accessories inside the bucket.”

From the archive · Full text
Reader shop tip

Peyton E. Smith

Peyton E. Smith, Covington, Tenn.

“I’m disappointed with the power steering and lift on my 1370 Case tractor. After re-placing some worn parts, it really isn’t much better. I also changed the hydraulic oil and filters. Does anyone have any ideas?”

From the archive · Full text
Reader shop tip

Don Voss

Don Voss, Spiritwood, Sask.

“To re-pair combine pickup rollers, round baler rollers, Hesston straw chopper rotors, and any other rollers that have shafts with only one washer supporting the end, we’ve come up with a handy repair. We install two washers inside each end of the roller, with one at the end and the other a couple inches inside the tube. We weld the washers to the shaft, then machine them in the lathe for a tight fit inside the tube. Makes them a lot stronger. For example, Hesston choppers get out of balance when the single washer bends slightly. We can save these expensive rotors with this simple repair.”

From the archive · Full text
Reader shop tip

Carlton Schwefel

Carlton Schwefel, Watertown, Wis.

“My Black & Decker pop rivet tool (model K111) that I bought last year really works good on anything that’s too thin to weld. I used it to repair a seam on a gravity box. I just took some light sheet metal and formed it to fit the angle of the seam and put the rivets in.”

From the archive · Full text
Reader shop tip

Larry Zenz

Larry Zenz, Parks, Ark.

“I use this portable vise in the hay fields behind my round baler to splice belts. I made it out of heavy pipe, 7/8-in. threaded rod, steel plate, and a disc blade. The disc blade forms the base. Two pieces of heavy plate steel mount on sections of pipe that fit inside each other. A “T” handle turns the pipe in and out.”

From the archive · Full text
Reader shop tip

David R. Schutz

David R. Schutz, Cayuga, Ind.

“I’ve found a way to break beads down on tires using my handy man jack. I set the tire flat on the ground under the end of a tractor axle. The base of the jack is placed on the tire against the rim and the lift mechanism set under the end of the axle. When you crank up the jack, the bead is pressed off the rim. I’ve haven’t found a tire yet that I couldn’t break down using this method.”

From the archive · Full text
Reader shop tip

Ken Turbett

Ken Turbett, Winnipeg, Manitoba

“I have a solid frame cultivator that is 20 ft. wide. Somehow the rockshaft got twisted so there was a 4 to 5 in. difference in cultivating depth from end to end. It had regular 15-in. implement tires on it originally. To solve the problem, we exchanged the tires on the high end for 14-in. car tires. The diameter difference of the tires is just enough to fix the problem. I saved the cost of having to change cultivators. If I need to fine tune tillage depth, I adjust tire air pressure.”

From the archive · Full text
Reader shop tip

Rick Mabeus

Rick Mabeus, Winfield, Iowa

“My mobile work bench rolls easily because it’s fitted with big air-filled wheels. Lets you always have tools and a work area at your fingertips instead of having to continually walk back and forth. It’s fitted with a light and electrical outlets. I can even tow it behind my garden tractor to take it out into the yard or field. I made the frame from tubing salvaged from an old field cultivator. The work surface is a combination of 2 by 10 planks and metal plate. Overall dimension of the bench is 5 by 8 ft. and the table surface is 36 in. high.”

Shop feature stories

From the archive · Full text
Feature story

Hands-Free Torch Lighter

Featured source:

Lighting a torch is as easy as flicking the end of it back and forth to strike the flint in “Safety Light” striker that clips onto the end of any torch.

It mounts permanently on the end of the torch. The striker flops back and forth when the end of the torch flicked, spark-ing a flint that lights the torch.

You never have to look for a hand held striker or match, and there’s no danger of burning your hand during lighting.

“With one flick of your wrist, the torch is lit,” says Dale Guinn, inventor and manufacturer.

Fits over medium and large size torch nozzles. Not small. Sells for $19.95 plus $2.00 shipping and handling.

Contact: FARM SHOW Followup, Dale Guinn, Safety Light, Inc., P.O. Box 344, Cleveland, Okla. 74020 (ph 918 358-2796).

From the archive · Full text
Feature story

AT & T Service Truck Box Makes Great Field Service Trailer

Featured source:

An old AT & T service truck box makes a handy field service trailer for Nebraska farmer Charles Myers. He mounted the box onto a 3/4-ton pickup chassis and welded a homemade tongue on front.

“It allows me to make most repairs right in the field and cost less than $2,000 to build,” says Myers.

Myers bolted the fiberglass box to the pickup frame. The box has compartments for a variety of power tools, a 110-volt air compressor, an oxyacetylene welding torch, containers of oil and grease, drawers filled with bolts, nuts, fasteners, screws, and other parts. A gas engine-driven generator mounts on top of the box. It powers 110-volt electrical outlets at both ends of the trailer as well as a 220-volt outlet on the generator. A homemade 100-gal. diesel fuel tank that’s centered over the axle - positioned between fuel compartments - lets him refuel tractors and combines right in the field. A homemade steel bumper on back doubles as an air tank, allowing him to use the air compressor to clean air filters and fill tires.

“At night I mount a pair of Halogen lights on top of the box to work on equipment,” says Myers.

“I mounted a small vise on the tongue.

“I paid $200 for the pickup frame, $400 for a used generator, and $150 for the fuel pump. I already had the fuel tank. I like my trailer-mounted unit better than truck-mounted ones because I farm 1,300 acres by myself and don’t want to be tied to a single vehicle. I can unhook the trailer in the field and use it while my wife goes to town for parts in the pickup. The fuel pump is wired into my pickup’s electric circuit, but I have a second hookup for it so that I can use a spare battery in one of the compartments to power it. Another advantage is that I can lock the trailer inside a shed and go somewhere without worrying that it’ll get broken into. Also, I avoid having to pay taxes and insurance on another vehicle.”

Myers used thick wall 4 by 6-in. steel tubing to make the bumper-air tank and welded a quick tach fill valve, shutoff valve, and pressure gauge onto it.

Contact: FARM SHOW Followup, Charles L. Myers, RR 2, Box 153, Lyons, Neb. 68038 (ph 402 687-4166).

From the archive · Full text
Feature story

Battery-Powered Grease Gun

Featured source:

You’ll like this new battery-powered grease gun that lets you lubricate any grease zerk by simply pressing a switch.

Distributor Roy Mai modified a German-made grease gun to make the unit, mounting an adapter housing that contains a rechargeable battery on one end of the tube. The battery powers an electric motor which direct-drives a pump that’s connected to the grease gun’s plunger.

“It takes all the work out of greasing a machine,” says Mai.

“It works better than an air grease gun because it’s totally portable and doesn’t need a compressor. The one-handed operation also makes it easy to use with a flex hose because you don’t have to do any pumping. It exerts up to 2,500 lbs. of pressure so it’ll put grease into the most stubborn zerk. Most conventional grease guns can exert no more than 1,800 lbs. of pressure. The battery will last for about two grease cartridges.

“It’s a high pressure, low volume grease gun so it doesn’t put out as much grease with every squirt as conventional high volume, low pressure grease guns put out. As a result it takes a little longer to do the job. However, it gives you more control and therefore reduces the possibility of over greasing.”

Sells for $74.95 with standard nozzle. An 18-in. long nozzle and a flex nozzle are also available.

Contact: FARM SHOW Followup, R & R Distributing, Rt. 1, Box 35, Tribune, Kan. 67879 (ph 800 292-7692 or 316 376-4039).

From the archive · Full text
Feature story

High-Horsepower, Low-Cost Cordless Drill

Featured source:

If you’ve ever shopped around for high-horsepower cordless drills, you know many of the most powerful can run upwards of $200.

Now, thanks to direct marketing, you can get a 14.4-volt 3/8-in. cordless drill for less than half that.

Pro’s Edge cordless drill comes complete with a high-voltage, long-running battery that lasts up to two weeks between charges, a charger power pack that recharges the drill in about three hours, a Jacobs keyless chuck, heavy duty high-torque gearbox and variable speed to 600 rpm’s for fast, precision drilling.

Comes with molded carrying case and 23-piece accessory set. Sells for $69.95 plus $7.95 S&H.

Contact: FARM SHOW Followup, Pro’s Edge, 301 Newbury Street, Dept. 131, Danvers, Ma. 01923 (ph 800 658-5959 or 888 257-6565 or 508 352-9900).

From the archive · Full text
Feature story

Changing Oil As E-Zee As One, Two, Three

Featured source:

Changing oil doesn’t have to be a messy job, say the manufacturers of this new mobile cart that collects drained oil and then pumps it out into a storage receptacle.

The E-Zee Oil Kaddee is only 11 in. high so it easily rolls under most any equipment. It features a 15-gal. drain pan, a 20-mesh stainless steel screen to protect its 10 gpm pump from foreign objects and an 8-ft. discharge hose. An on-off switch mounted on the handle activates a 1/2 hp motor which drives the pump.

By attaching a suction hose to the unit, it can be used as a transfer pump when it’s being used as a holding tank during repairs.

Sells for $725 plus $50 S&H.

Contact: Juneau Sales, R.R. 3 Box 106, Red Lake Falls, Minn. 56750 (ph 218 698-4222).

From the archive · Full text
Feature story

VW Engine Great For Repowering Bobcat

Featured source:

After years of hard use with little need for repair, Ralph Johnson’s Bobcat 500 skid steer loader needed engine repair.

“It would have cost more than $1,000 for labor and parts to repair the 2-cylinder Kohler engine,” says the Michigan farmer.

“I looked around at small engines about the same size and found that a Volkswagen engine from a Jetta car would fit perfectly. A Volkswagen engine operates at about 100 psi oil pressure so any engine you find in a junkyard is likely to be in good condition. The valves might need grinding, but that’s about all.

“Fitting the engine into the cavity of the machine was a logical process. The most difficult part was making an adapter to fit the pulley onto the crankshaft. I made four adapters before I was satisfied that I had a perfect fit. The adapter to run the hydraulics on the opposite side of the engine was simple to do.

“I’ve used the repowered Bobcat for a year now with no problems. I could have installed a governor but I chose to put a choke cable on that’s attached to the carburetor. I ran the cable up through the steering lever so the choke button is on top of the steering arm. So as I work the steering I can control engine speed at the touch of my thumb.

“Any belt-driven Bobcat could use this engine. The 4-cyl. VW puts out over 57 hp, which is considerably more than the original Kohler. The engine is water-cooled and the radiator is about the same width as the Bobcat. I put a hinged frame on back to hold the radiator and to open the back of the motor compartment for service.

“The cost of the engine was about $200. I could build the crankshaft adapter for sale if there’s interest, or make blueprints available.”

Contact: FARM SHOW Followup, Ralph F. Johnson, 4597 Sunflower Ridge Dr., Ada, Mich. 49301 (ph 616 874-6827).

From the archive · Full text
Feature story

Low-Cost Driveline Parts

Featured source:

The next time you need replacement drive train parts for your farm machinery, car, or truck, you might want to contact a Virginia parts supplier that sells drivetrain and component parts for 2 and 4-WD vehicles as well as farm machinery. The company can also custom-build virtually any driveline part.

“We sell complete drivetrains at wholesale prices - about half the price that dealers charge. We specialize in 4-WD parts including 4-WD front and rear axles, hub lockouts, Jeep rear axle kits, clutch kits, etc.,” says Ronnie Gordon, president of “Mr. Axle”.

“We can deliver parts by UPS over-night or drop ship them from different manufacturers. We can supply parts for most any car or truck, and many brands of farm machinery. We specialize in driveshafts, pto’s, remanufactured rack and pinions, Dana Spicer truck and car drivetrain parts, ring gear and pinions, differentials, spindles, truck hubs and rotors, axles for front-wheel drive cars, and much more.

“We can take orders for custom-built parts right over the phone. The customer tears the part from the vehicle and calls in the measurements.”

Contact: FARM SHOW Followup, Mr. Axle, Box 866, Railroad Ave., Rural Retreat, Va., 24368 (ph 800 926-2953 or 540 686-4137 or 4128).