Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Bobby Rader
“Copper wire theft is a multi-billion-dollar problem just in agriculture, not counting municipalities and cities, where the loss impacts so many people,” says Bobby Rader, co-creator of the Farmblox COP-R-LOCK Security System.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Cal Miner, Willmar, Minn.
“I’ve found that Menards periodically has 4,000 to 5,000-lumen LED shop lights on sale for under $10. Recently, I saw them on sale for $6 after a rebate. They work great as trouble lights because they stay cool…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ralph Volkman, Black Creek, Wis.
“The power went out on both sides of the jaws of my old jumper cables. On a new set, only one side of the jaw transferred power. I drilled out the rivets and installed a loop of copper…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Howard Sklar, Aurora
“If you want to preserve a car (or other) battery that won’t be used for a while, especially in cold weather, you don’t need an expensive drip-charge system. Just remove the negative terminal from the battery. I wrap…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“Battery cables slipping out of the clamp is a common problem. No cable means no battery charge. Try stripping extra wire and putting a bend on the end. Allow plenty of extra stripped wire.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“Take a mushroom box (or other small container) and put a magnet inside to keep small steel bits from spilling or getting lost. It can be stored at any angle as needed. It works great under the truck.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“Before sorting items on a bench, lay a towel down and place a 4 by 4 near the edge. No more small bits falling off and getting lost, and the towel lets you pour them back into the…
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 4
Individual tip 4 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“For many of us, finding the tool we need can be impossible. Try taking the tools you seldom use and store them separately.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Steve Dietrich, Morton, Ill.
Steve Dietrich of Morton, Ill., upgraded his 1961 Jacobsen lawn tractor by repowering it with a 6.5-hp Predator engine.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Cal Miner, Willmar, Minn.
“Angle grinders of all sizes need to be periodically opened up and regreased or lubed. The grease that comes with them is very thick and cakes in the housing, leaving no lubrication on the spindle and gears.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Cal Miner, Willmar, Minn.
“I had a dark area in my shop where it was hard to see my tools. I bought a battery-powered twin light with a motion sensor. The motion sensitivity and duration can be adjusted.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Cal Miner, Willmar, Minn.
“Sometimes, it can be hard to loosen a nut. This photo shows the friction-drive wheel on a rear-engine Snapper rider. To keep the pry bar on the studs while loosening the nuts, reverse a flange nut and turn…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Matt Steffen, Lincoln, Neb.
When Matt Steffen’s family member lost the control knob of his Solar Pak 6 electric fencer, he ran into an unexpected problem.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Farm Innovators, Plymouth, Ind.
Save money by turning on heaters only when needed with a Thermo Cube thermostatically controlled outlet. Whether it’s an engine block heater, heat tape, heat lamp, or stock tank heater, why use electricity when it isn’t necessary?
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Milwaukee Tool, Brookfield, Wis.
Just when you thought you had all the flashlights you needed, Milwaukee introduced the M12 Underbody Light. The light features two swivel points that offer 300 degrees of horizontal rotation and up to 180 degrees of vertical rotation.…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Larry Goodman, Ionia, Mich.
Larry Goodman had no good way to see the forks attached to the bucket of his backhoe. He purchased a wireless backup camera with a strong magnetic base and placed it inside the bucket, and placed the monitor…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: NightBuddy
Holding a flashlight while trying to make a repair is never easy. Traditional headlamps often have a narrow beam of light.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
William Ridgway, Salem, Ind.
“My wife had trouble removing the battery from our Ryobi string trimmer. So, I glued some rubber feet onto the pads of an inexpensive squeeze clamp. Although it won’t win any beauty contests, it sure does work.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Allen Pederson, Nashua, Iowa
“I found a single field cultivator tooth with a spring on the highway. I bolted it to a tractor bucket to dig electric cable in.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Jeff Hootman, Jeromesville, Ohio
“The power windows on my 2002 Ford Taurus quit due to an electrical problem on the driver’s door. When they started to come down on their own, I had to do something. I removed the door panel and…
Read the complete tip →From the archive · Full text
Reader shop tip
Donald Albright, Perkins, Okla.
“I discovered that batteries, like those in flashlights, clocks, and appliances, have a film on them which causes them to give out quickly. When they go bad, use a nail file on the finest side to ‘shine’ both…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Glenn Dawson, McConnelsville, Ohio
“I had trouble with the front hydraulic cylinder on my Kubota tractor. I replaced it with a 12-volt winch. It works great.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ralph Volkman, Black Creek, Wis.
“I wrap rubber electrical tape on my ice fishing tip-ups for fast respooling of line.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
David Simpler, Elkton, Md.
“When the electric linear actuator that raised and lowered my disk stopped working, I found an alternative.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“I couldn’t find a good electrical ground for my test light. So, I ran a long wire from the negative post on the battery back into the truck cab and clipped the test light to that. There are…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Matco Tools, Stow, Ohio
Matco soldering clamps make soldering wires easier. Matco offers two models. Both feature spring-loaded, articulated claws that hold wires securely. The clamps handle wires up to 0.177 in. dia. (gauge 7).
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Meeks, Verona, Va.
“I’ve had a lot of trouble with fractional horsepower electric motors seizing and sticking, especially window fans. Oiling them isn’t enough as they quickly stick again. It’s as if the grease turns to glue. I found the cure—…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Fritz Groszkruger, Dumont, Iowa
“The two halves of the loader control handle on 5105M cost $876 to replace. I’m trying to repair it with JB Weld. I imagine these parts prices are to subsidize their electric tractors. The world has gone nuts.”
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Bill Kendall, Maryville, Tenn.
“I replaced the 8-ft. fluorescents in my shop with LED lights, reduced the amp draw and 13.9 amps per circuit to 4.8 amps per circuit. The luminosity is greatly improved, I can see much better in the work…
Read the complete tip →From the archive · Full text
Reader shop tip
Eric Philippsen, North Fort Myers, Fla.
“I use a ‘trickle charger’ on our 12-volt batteries. As a result, the machinery starts right away every time.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Paul Scholand, Ypsilanti, Mich.
“I have a tractor with a front-end loader. The battery is just inside the front grill. If the loader isn’t in the raised position, it’s hard to connect a charger or jump pack to the side battery terminals…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
Paul Scholand, Ypsilanti, Mich.
“I had taller trusses put into my garage ceiling and laid some angle iron across three to anchor an electrical lift. I can put heavy snowblowers and generators onto my roll-around worktable easily and safely.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Floyd Plank, Whitewater, Wis.
“If power tool batteries go too low and don’t want to recharge, I take two electrical wires and bare the ends a little. I poke one end in on the plus and the other wire in the minus…
Read the complete tip →From the archive · Full text
Reader shop tip
Jeffrey Mitleiser, Vesper, Wis.
“Replacing bulbs in my shop lights with 3, 4, or 5-panel LED lights really made my shop bright.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Michael Halbirt, Silverton, Ore.
“I have several Black & Decker and Sears power tools. They were designed to just plug an extension cord into the tool rather than having their own cord. But, as you’re using the tool, the extension cord falls…
Read the complete tip →From the archive · Full text
Reader shop tip
Joe Kansak, Ocean View, Del.
“I have a 10,000-sq. ft. shop, and it seemed like we were always leaving stuff on. I would come in and discover a heater, air compressor, or lights hadn’t been shut off. Left on for a day or…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Ronald Hurst, Knoxville, Tenn.
“I frequently work on small electric motors 1/2 hp. and below, especially small fan motors. I don’t like using 3-in-1 oil as a lubricant because it dries up fairly quickly, leaving a gummy varnish on the shaft and…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: GMS Power Distro
GMS Distribution manufactures portable power distribution boxes and electric cords specifically designed for contractor use. The boxes, created by an electrician, are compact and lightweight for easy portability.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Grady Hurst, Knoxville, Tenn.
“For lack of a better name, this is a ‘Pedal Presser Downer’ tool. You press down the gas or brake pedal of a car or track and put this tool in place to hold the pedal down. This…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Larry Goodman, Ionia, Mich.
“I accidently cut the cord while I was trimming shrubs with my electric hedge trimmer. While I was fixing the cord, I had the idea to hook a carabiner clip to my belt loop and run the extension…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ronald Hurst, Knoxville, Tenn.
“This is a handy, fairly inexpensive tool that turns a round hole (3/8 in.) in sheet metal into a rectangular hole, any size. I use my nibbler mostly for squaring holes in electrical/electronics projects (holes for things like…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Ben Parks, Austin, Texas
“On 2-prong electric cords, I use permanent markers to mark the wide end so I can plug them into a 120-volt outlet the first time without having to look at the prongs. I use a black marker on…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dale McLaen, Rutland, N.D.
You can never have too much light when moving snow with a skid steer at night, but too bright a light can blind others working around you. Dale McLaen solved the problem by attaching LED lights to the…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Toro
Toro says its Impulse Endeavor power inverter works with any Toro 60V Max Flex-Force battery (not included). The inverter converts DC battery power to AC. It has three outlet power options (USB-A port, USB-C port, and 120V outlet)…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Hornblasters, Tampa, Fla.
Hornblasters sells a wide range of powerful air-powered horns that sound like a semi-truck horn or even a locomotive (Vol. 36, No. 4). But if you don’t want to install an air compressor, they also sell easy-to-install 12…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Hector Nieves
We spotted this idea by Hector Nieves on Instagram. He made a portable wooden cord holder and outlet stand that’s easy to move around his shop. The base is a foot-long piece of 2 by 12-in. plank that…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: LED Flashlight Gloves
At first glance, LED Flashlight Gloves seem like a quirky novelty.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Robert Bauer, Hastings, Minn.
“I made a rather crude cord reel way back in high school shop class, and it worked so well that I expanded on that idea over the years and built several more,” says Minnesota farmer Robert Bauer. His…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Reid Allaway, Les Cedres, Quebec, Canada
“We made an inexpensive and simple aerial electrical mast for our fabric equipment shelter using parts from an old TV antenna tower, some extra black pipe, and various conduit pieces and fittings,” says Reid Allaway of Tourne sol…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Matco Tools
Hang the rechargeable, collapsible MCFL800 floodlight (about $100) from Matco from the hood or slip it under the car. It’s ideal for emergencies, like changing a tire, jumping a battery, or anytime you need more light. With its…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: K&M Manufacturing
K&M Manufacturing sells Tiger Lights LED light kits for Deere and Case IH combines. Each lighting kit makes it possible to fully outfit your combine with LED lights.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Gary Sampson, Freedom, N.Y.
“I glued a plastic piece of bit holder onto the side of my screw gun so when I have to change bits, I’ve got them handy right where I need them. I also glued a small bar magnet…
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Swensen, Yankton, S.D.
“My dad called this big 1/2-in. electric drill ‘Big Bertha’. It’s a 1938 model which was patented in 1917 by Black & Decker. It takes a big man to operate and takes two trigger pulls to start and…
Read the complete tip →From the archive · Full text
Reader shop tip
John Johnston
“I make these turnbuckles to tighten up a run of barbed wire. They cost almost nothing and take only 15 min. to make versus paying $20 for something similar in town. All you need is 5 or 6…
Read the complete tip →From the archive · Full text
Reader shop tip
Ready Davis, Bigfoot Equipment & Repair, Willow Creek, Calif.
“As a Husqvarna dealer I feel I should respond to recent readers who have had issues starting their 562XP chainsaws. I understand their frustration. The manual is less than clear and the ‘universal’ symbols on the starting decal…
Read the complete tip →From the archive · Full text
Reader shop tip
Bruce Warren, Wellsboro, Penn.
“Ask your local auto parts dealer if you can trade a dead battery for a core exchange battery with some life left in it. All my seldom-used 6 and 12-volt equipment with coils use them. I’ve saved hundreds…
Read the complete tip →From the archive · Full text
Reader shop tip
Dale Fisher, Jackson, Mich.
“I have discovered that when alkaline batteries die in a device there is often still a little life left. By testing with a voltmeter, generally, if one battery is dead the other one may not be because the…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Mark Yax, Solon, Ohio
“I had an electric stove that I was tossing out. When removing the bottom drawer, I noticed that the stamped steel tub would make a nice drain pan or parts washing tub. I removed the front door panel…
Read the complete tip →