From the archive · Full text
Feature story
Featured source: John Webb
Looking for cutterbar replacement parts? You don’t have to look any farther than Webb’s Sickle Service, Grand Island, Neb. John Webb carries parts for 20 different major manufacturers and 10 to 12 short line companies.
Read the complete story →From the archive · Full text
Feature story
Featured source: Light Racing
Light Racing’s new JounceShock is a patent pending new form of air shock that’s never before been available to the public in bolt-on kit form. The technology originated from desert racing and has now been adapted for everyday…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: John Craig
Collectors of Deere Orchard tractors will have an easier time restoring their tractors to original condition if they work with John Craig. As co-owner of Craig Welding in Mentone, Indiana, and a collector of Deere tractors himself, he…
Read the complete story →From the archive · Full text
Reader shop tip
Charles Klein, Columbia, Ill.
He built a table specifically for painting tractor parts. He came up with the idea of using expanded metal because it allows the surplus paint spray to flow on through without puddling up.
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Conyers, Weatherford, Texas
“A good idea I had when I built my shop was to insert a 4-in. sq. steel tube post into the ground before the floor was poured. There’s a flat steel plate on top for mounting a large…
Read the complete tip →From the archive · Full text
Reader shop tip
Pete Peters, Osler, Sask.
“I came up with a portable chainsaw sharpening vise by bolting a small vise to the top of a 3-ft. high steel pipe, which is welded into an old car wheel hub that serves as a stand.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 6
Individual tip 2 of 6 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
“I narrowed up this shovel to make it easier to dig. At 78 years old and living with arthri-tis, the smaller sized shovel allows me to work in greater comfort. I also welded a full width 1/8-in. thick…
Read the complete tip →From the archive · Full text
Reader shop tip 5 of 6
Individual tip 5 of 6 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
“A great amount of our food is sold in plastic, cardboard, and metal packages. These packages can be recycled into useful items that make our lives easier and also reduce the waste going into landfills. Many of the…
Read the complete tip →From the archive · Full text
Reader shop tip
Boyd Butler, Blackwell, Okla.
“While restoring a 1939 John Deere B tractor I repowered it with the engine from a Deere 212 riding mower. I removed the tractor’s pistons, rods and block, then made a plate and put it on the crankcase…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Don Fleming, Zearing, Iowa
“I built this numbered filing system in my garage for stuff ranging from small tools to light bulbs. The plywood shelf is about 20 ft. long and 20 in. deep and is supported by a series of metal…
Read the complete tip →From the archive · Full text
Feature story
Featured source: John Nightingale
A personal quest to convert his vehicles to burn waste vegetable oil led Oz Cheek to become a distributor for Dieselcraft oil cen-trifuges. Along the way he discovered they’re also a great way to completely eliminate con-ventional oil…
Read the complete story →From the archive · Full text
Feature story
Featured source: Ron Mickle
The balcony storage area in Ron Mickle’s shop is much more useable now that he can get there by elevator.
Read the complete story →From the archive · Full text
Feature story
Featured source: Jim McGean
Owners of Dodge and Ford 4-WD trucks can beef up their front ends, improve mileage, and reduce road vibration by reworking factory front axle assemblies.
Read the complete story →From the archive · Full text
Reader shop tip
Joe Rupnicki, Soldier, Kan.
“I got tired of dragging a welder and tools around the farm when equipment broke down. So I bought a large cargo van – I think it had been a bread delivery truck. It’s 6 1/2 ft. tall…
Read the complete tip →From the archive · Full text
Reader shop tip
Lowell Tuplin, Ellerslie, P.E.I.
“During winter I use a winch on back of my tractor to skid logs out of the woods, and small trees and branches were catching on the valve stems on the rear tires and breaking them off.
Read the complete tip →From the archive · Full text
Reader shop tip
Metal Supermarkets, 170 Wilkinson Rd., Unit 18, Brampton, Ontario, Canada L6T 4Z5 ph 866 867-9344 or 905 459-0466; www.metalsupermarkets.com
If you need metal bars, plate, or sheet metal, you’ll be interested in this company. It claims to be the world’s largest supplier of small quantity metal and says it can provide one stop shopping for all your…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Wess Cornelius, Winlock, Wash.
“I wanted to use my cherry picker to lift engines but couldn’t get it close enough to my motorcycle lift with the legs on. To solve the problem, I built an extension rack on the rear and bottom…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Wess Cornelius, Winlock, Wash.
“There’s never enough level space in a shop. To solve this problem, I mounted metal doors with hinged legs to one of the walls. When folded up, the doors are out of the way. When folded down, the…
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Bugger, Effingham, Ill.
Bob likes to keep a tidy shop. That’s why he created this setup to capture and hold grit and sparks from his chop saw.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Loron Skretteberg
“I used to build pole buildings and hated using tin cutters to cut the sheet metal. So one weekend I went out to my shop and built a radial arm steel cutting saw,” says Loron Skretteberg, Carson, N.…
Read the complete story →From the archive · Full text
Feature story
Featured source: Wess Cornelius
Wess Cornelius couldn’t justify the expense of a new air compressor. So the Winlock, Wash., man converted a Rotec 500 cc, 2-cyl. snowmobile engine into a low-cost air compressor.
Read the complete story →From the archive · Full text
Feature story
Featured source: Harold Witulski
“I made a sand blaster-compressor from a car motor,” says Harold Witulski of Beatrice, Neb.
Read the complete story →From the archive · Full text
Feature story
Featured source: Wess Cornelius
“It puts my shop tools right at my fingertips without having to do any walking,” says Wess Cornelius, Winlock, Wash., who converted a round wooden kitchen table into a rotating shop table.
Read the complete story →From the archive · Full text
Feature story
Featured source: Lloyd Statz
Put a Mercedes Benz 2.2-liter, 4-cyl. diesel engine into a 1944 Farmall H and you’ll have a nice, smooth-running combination, says Lloyd Statz of Elmwood, Wis., who did just that.
Read the complete story →From the archive · Full text
Feature story
Featured source: Levi Glick
Getting rough work milled or machined is seldom hard to do at a local metal shop. But getting a complex part machined, which requires fine valve and stem work, can be a lot tougher. One alternative is to…
Read the complete story →From the archive · Full text
Feature story
Featured source: Ken Young
“Our new air induction kit solves cold weather icing problems on Honda V-twin engines equipped with overhead muffler systems,” says Ken Young, Brandon, Manitoba.
Read the complete story →From the archive · Full text
Reader shop tip
Carter M. Ramsey, Saint Simons Island, Ga.
“My Yanmar 22 hp 4-WD tractor tended to run hot whenever I worked it hard; for example, when plowing or disking to build wildlife food plots for our hunting club. To solve the problem, I went to our…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Frank Dyck, La Crete, Alberta
“I bought an old IH 241 round baler that gave me a lot of trouble. It had trouble starting a bale because the smooth steel rollers wouldn’t grip the hay or belts properly. I solved the problem by…
Read the complete tip →From the archive · Full text
Reader shop tip
Rob Sharp, Watford, Ontario
“I came up with a handy overhead hoist and wheels in my shop using a section of barn door track that I bolted to the ceiling. The track is welded to 18-in. lengths of angle iron that are…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Ben Barwick
“Anyone who has an antique one-lunger gas engine and would like to show it off will be interested in my antique cast iron wheels and axles. They can be used to make an antique engine-hauling cart that really…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bob Bugger, Effingham, Ill.
“I found this used camper refrigerator, which turned out to be just the right size for storage of welding rods. I keep it on top of my welding machine.
Read the complete tip →From the archive · Full text
Reader shop tip
Don Ickes, Osterburg, Penn.
“I used a pair of steel I-beams and other salvaged materials to come up with low-cost ‘grease mon-key’ ramps. They work great for changing oil on vehicles, removing the blades from my riding mower, and many other jobs.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Don W. Thomas, Eureka, River, Alberta
“I bought a used moldboard plow several years ago that needed new shares. Rather than buy new ones, I welded used shares over the old shares, low enough to equal new ones. It worked as well as installing…
Read the complete tip →From the archive · Full text
Reader shop tip
Gale Courson, Farina, Ill.
“My all steel work table has caster wheels so I can roll it anywhere I want to work on a job. The table has a vise for holding items in place.”
Read the complete tip →From the archive · Full text
Reader shop tip
Mr. Funnel, 3119 SW 42 nd Ave., Palm City, Fla. 34990 ph 772 287-6157; www.mrfunnel.com
This company offers a fuel filter that removes water and other contaminants from fuel, improving engine durability and performance. Mr. Funnel fuel filter is a heavy duty, fast-flow, poly funnel with a built-in stainless steel filter. It’s designed…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Lassila, Great Falls, Mont.
When pouring the floor for a new shop, I recommend installing a grounding device in the floor between your welder and the welding bench. This avoids some of the hassles of the grounding clamp and cable. Rebar works…
Read the complete tip →From the archive · Full text
Reader shop tip
Tim Force, Montrose, Colo.
“I pop riveted a piece of stainless steel screen into the air passage to my truck’s air cleaner. Keeps mice and pack rats from nesting in the air cleaner.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Bruce Chandler
Cutting metal with a hacksaw gets old fast. That’s why building a metal cutting bandsaw seemed like a good idea to Bruce Chandler, a former auto mechanics instructor who likes to build miniature engines. He already had a…
Read the complete story →From the archive · Full text
Feature story
Featured source: Dale Denton
Anyone who owns a Deere 4020 tractor with duals knows that over time the wheel hubs work loose, damaging the key so badly that the hub can no longer be used.
Read the complete story →From the archive · Full text
Feature story
Featured source: Don Knasel
“We had tremendous response to your original article from readers all over North America who want more power in their Ford N-Series tractors,” says Don Knasel, who developed a kit that makes it a snap to install V-8…
Read the complete story →From the archive · Full text
Feature story
Featured source: Mel Primrose
Mel Primrose keeps his lawn tractor in tip top working condition, thanks to a mini service center he built next to his shop.
Read the complete story →From the archive · Full text
Reader shop tip
Charles Klein, Columbia, Ill.
His advice to anyone making a shop table: Be sure to make it big enough. That’s what Charles did when he used a full 4 by 8-ft. sheet of 5/ 16-in. steel for a table top when making…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gordon Black, 42042 E. Lane 16, Burns, Oregon 97720
“I wanted to cut the lid off a 55-gal. steel barrel, but I was afraid to because I didn’t know what kind of material the barrel originally contained. To solve the problem, I closed the jaws of a…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 5
Individual tip 1 of 5 from this reader’s published contribution.
Richard Gribbins, 1915 Merrimac Rd., Bradfordsville, Ky. 40009
“Over the years I’ve made several different metal brackets that let me mount extra toolboxes on my three Ford New Holland tractors - a 3930, TN 70DA, and 2600. The factory toolboxes on these tractors are either too…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 5
Individual tip 2 of 5 from this reader’s published contribution.
Richard Gribbins, 1915 Merrimac Rd., Bradfordsville, Ky. 40009
“I also made a metal feed carrier bracket for my TN 70 DA tractor. I use it to haul three 5-gal. buckets full of corn to my heifers on pasture. I used angle iron and rebar to make…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 5
Individual tip 3 of 5 from this reader’s published contribution.
Richard Gribbins, 1915 Merrimac Rd., Bradfordsville, Ky. 40009
“I also mounted a homemade bracket inside the cab on my TN 70 DA tractor that holds a 1-gal. plastic jug of water. The bracket has plastic sides and an expanded metal floor. It mounts under the dash…
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 5
Individual tip 4 of 5 from this reader’s published contribution.
Richard Gribbins, 1915 Merrimac Rd., Bradfordsville, Ky. 40009
“I used angle iron and steel plate to make footrests on both sides of my 3930 tractor. The footrests mount forward and above the cab platform and provide room for me to stretch out my legs.
Read the complete tip →From the archive · Full text
Reader shop tip 5 of 5
Individual tip 5 of 5 from this reader’s published contribution.
Richard Gribbins, 1915 Merrimac Rd., Bradfordsville, Ky. 40009
“I have short legs and had trouble fully depressing the clutch pedal on my TN 70 DA tractor, so I fixed metal brackets onto the existing clutch pedal that add 3 in. of height. The bracket is made…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Don Bragdon
If you’ve ever wished you could put more down pressure on a handheld electric drill, you’ll be interested in this simple tool built by Don Bragdon of London, Arkansas.
Read the complete story →From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky.
“I started using a power chair about a year ago after arthritis made walking too painful. But I still manage to do what’s needed. Here’s a photo of my ‘hand truck’, which I use with a cardboard box…
Read the complete tip →From the archive · Full text
Reader shop tip
Leonard Seltzer, Manhattan, Ill.
“I made this 9-in. long drawbar pin out of an old 3/4-in. dia., solid steel compressor valve. I ground one end of the valve down to a point and then welded a washer on about 2 in. from…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Kim Tschetter
Years of driving combines have given Kim Tschetter first hand knowledge of combine repairs. The cost of high-priced replacement parts prompted him and his family to start a company to design and build aftermarket parts.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: David Stewart
Once you’ve tried it you’ll never go back, says the inventor of this new front-claw hammer.
Read the complete story →From the archive · Full text
Feature story
Featured source: Stainless Steel Brakes Corporation
Need better braking than you get with your stock brakes? You can increase brake torque by up to 36 percent over stock brakes with a heavy-duty brake system from Stainless Steel Brakes Corporation (SSBC). The company offers disc…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bob Bugger, Effingham, Ill.
Bob reduced wire changing time on his mig welder by installing an extra spool dispenser that he designed himself.
Read the complete tip →