From the archive · Full text
Reader shop tip
Gerald Westhoff, New Vienna, Iowa
“Holding pto and driveline components in a vise can be a challenge because it’s hard to hold them in place while turning the handle. After 30 years of working with pto’s and drivelines, we’ve developed a ‘C’ frame…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Jeff Kumpf, Hopedale, Ill.
“On a rainy fall day, I decided to address the lack of organization of my air tools. I had been keeping everything in a drawer with almost no hope of finding what I needed. The air tools would…
Read the complete tip →From the archive · Full text
Reader shop tip
Co-Leash Corp., Tampa, Fla. (ph 888 838-2169; www.krypta-glow.com)
Kryptaglow is a glow-in-the-dark fluorescent paint that shines bright for 24 hours after being exposed to light for just 15 min. It can be used on walls, floors, metals, or on just about any properly prepared surface. During…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Justin Kelzer
The 1/4 hp, 4-speed drill press Justin Kelzer built consists of an antique Champion #97 post drill with a pulley drive attached. Kelzer added a motor and transmission and mounted everything to a wood frame.
Read the complete story →From the archive · Full text
Feature story
Featured source: Tom Pearson
“Before I started using my homemade slackener it used to take me 15 to 20 min. per row to loosen the gathering chains on my cornhead, remove them, clean under the sprockets, then put the chains back on…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Deb Del Piero
The Clog Hog drain cleaner works with many pressure washers to unclog sewer lines and pipes.
Read the complete story →From the archive · Full text
Feature story
Featured source: Vern Goodwin
“I needed a hoist to help mount a sidecar on a motorcycle,” says Vern Goodwin, a Lincoln, Neb., cycle shop owner who built what he calls a table hoist.
Read the complete story →From the archive · Full text
Feature story
Featured source: Vince Osburn
Vince Osburn’s homemade grinding tool lets him get inside the differential housing on a Deere 2020 tractor to guide a grinding wheel to resurface the brake contact area. Adding a second plate and spacers make the tool perfect…
Read the complete story →From the archive · Full text
Feature story
Featured source: Wayne Hopper
“I was sitting on a beach in Florida and this idea just came to me,” says Brussels, Ont. farmer Wayne Hopper, who built his own portable hydraulic car and truck hoist out of steel tubing, loader cylinders and…
Read the complete story →From the archive · Full text
Reader shop tip
Clark Dysle, Scio, Ore.
“I found a leak in the fuel line on my Ford 10-yard dump truck. I used a grinder and a jigsaw to cut a square hole in the truck’s floorboard so I could access the fuel line without…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
David McRae, Whitehall, Wis.
“I wanted a way to extend the use of hard-to-find tractor tires once they developed breaks in the sidewall. So I made boot inserts out of 10-in. smooth triple-ply belting. I bevel the edge of the cut. Then…
Read the complete tip →From the archive · Full text
Reader shop tip
David Pidgeon, New Haven, Vt.
“Many times when I’m away from my shop I’ve wished I had a vise to use on some job. So, I came up with this vise-mounting bracket that works with any standard 2-in. receiver hitch.
Read the complete tip →From the archive · Full text
Reader shop tip
Butch Alcorn, Encampment, Wyo.
“I came up with this handy shirt pocket tool that lets me use wire clips to attach fence wire to T-posts. I start with a 6-in. spike and grind the point off, then drill a 1/8-in. dia. hole…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Co-Leash Corp., Tampa, Fla. (ph 888 838-2169; www.krypta-glow.com)
Kryptaglow is a glow-in-the-dark fluorescent paint that shines bright for 24 hours after being exposed to light for just 15 min. It can be used on walls, floors, metals, or on just about any properly prepared surface. During…
Read the complete tip →From the archive · Full text
Reader shop tip
Jon Warwick, Warwick Ideas, LLC, (ph 601 954-5776; www.stavepress.com)
“Our portable StavePress is designed to gently but firmly hold irregularly shaped wood pieces without damaging the wood grain. It grips the work piece between 2 horizontal rubber-cushioned plates, allowing me to bear down hard with tools without…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Years of experience dismantling and rebuilding Deere balers have proven to Nelson Horning that Tucker Fingers in the knotters are nearly always worn and have a lot of play. Horning builds replacement Tucker Shafts for use on Deere…
Read the complete story →From the archive · Full text
Feature story
Featured source:
James Osnes needed a sandblasting cabinet and he had a bunch of “weldable” industrial plastic on hand after helping a neighbor build dog kennels. He decided to use the plastic instead of steel.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Arthur Kidder doesn’t worry about overloading his tractor’s front-mounted forklift anymore. His bolster repair is heavy enough to carry nearly any load.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“They work great to lift heavy parts and equipment,” says Andy Hall, who operates an on-farm repair and welding shop on his family’s farm near Butterfield, Minn.
Read the complete story →From the archive · Full text
Feature story
Featured source:
This company has been “dieselizing” Toyota, Jeep and Ford Ranger vehicles since 2004. The company guarantees that electronics, accessories, gauges and air conditioning will work just as they did when the vehicle arrived in its shop. Cost of…
Read the complete story →From the archive · Full text
Feature story
Featured source: Greg Stephen
“If you’re looking for rare and hard-to-find tractor parts, I probably have them, know about them, or can tell you where to find them,” says Greg Stephen, who has made antique and unusual parts his business for the…
Read the complete story →From the archive · Full text
Reader shop tip
Mike Marshall, Orchard Park, N.Y.
“I work for a local milk processing plant and recently made this portable removable vise for our service truck. Works great for road calls.
Read the complete tip →From the archive · Full text
Reader shop tip
Wesley Walker, Cooper, Texas
“I had a problem with the gearshift lever on my IH 86 Series tractor. The lever is made out of common bar stock and it wears around the vertical transmission shaft, which makes shifting gears difficult. To solve…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
You can boost the performance and efficiency of diesel engines with aftermarket products that modify air intakes and exhausts. Several products are available for diesel pickup engines and brand name farm equipment. internet only company that offers a…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I came up with a portable shop crane by turning a standard engine hoist backwards,” says Steve Brouillard of Early, Texas.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“If you’ve got an older Deere tractor that you want to hook up to a manure spreader or a mower or some other tool with a 20 spline pto shaft, this insert shaft makes it real easy,” says…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Elmer Fisher is in the business to provide customers – mostly Amish – with power tools that don’t require electricity. But his chopsaw powered by a weedeater motor may attract a wider variety of customers. The owner of…
Read the complete story →From the archive · Full text
Feature story
Featured source:
The shop exhaust system sold by Central Pointe, Inc., normally goes to implement repair shops, truck shops and other commercial operations. That’s changing, according to Mike Passkewitz, Central Pointe.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Larry Fulton
Larry Fulton’s hammer rack makes it easy to find the right hammer. Wheels on the rack allow him to move it to where the work is, so he doesn’t have to go back for a different hammer in…
Read the complete story →From the archive · Full text
Reader shop tip
Alton Eliason, Northford, Conn.
“I’m 95 years old so steering my Cub Cadet has gotten a bit more difficult. I was looking for a power steering unit when my nephew, a brilliant young mechanic, suggested I just get a couple of thrust…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
George Bagnall, Paincourt, Ont.
“The Woodruff key kept breaking on the elevator on my Massey 300 combine after I welded it twice. The third time I used stainless steel rod and that did the trick. No more problems.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Robert McMahon, Knoxville, Tenn.
“I was tired of having to break fittings to relieve hydraulic pressure when connecting the grapple on my front-end loader and backhoe attachment. So I made a clamp to connect the hydraulic connectors that are under pressure. Works…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Robert McMahon, Knoxville, Tenn.
“I came up with a method to drill 1/2 in. or larger holes in steel pieces that I could not bring to my drill. I had previously had problems breaking large, expensive bits. Now I use bimetal hole…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Tavish Presswood, Canton, Ga.
“I needed to get rid of some big dents in the sides of my Bush Hog mower, which were caused by turning too short around trees. To straighten out the dents I made a notch in a 1/2-in.…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“I made a simple service ramp for my Kawasaki Mule utility vehicle out of 2 sets of car ramps with planks bolted on between them,” says Delbert Hayes, Norwalk, Iowa. He set the 2 sets of car ramps…
Read the complete story →From the archive · Full text
Feature story
Featured source:
When Noah Hubbard picked up some surplus wall cabinets, he had a brainstorm that he could use one to pull dust from his shop/garage.
Read the complete story →From the archive · Full text
Feature story
Featured source:
A leveler kit installed on your Ford truck makes it easier to pull heavy loads, but can cause wheel wobble and tire wear. BD Diesel has a simple solution – a $225 Cam Caster Adjuster kit, which installs…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dave Geyer
If you need a hood for a tractor you’re restoring, Dave Geyer can help. For the past 14 years, Geyer has made hoods and other sheet metal parts. He has shipped orders to customers in each of the…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Stew Kunkel made a nifty portable stand for his metal chop saw. It supports long pieces of steel to be cut, lets him swivel the saw easily to cut angles, and carries the saw into storage when not…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Steve Konieczki devised a way to use his DeWalt 18-volt battery charger to charge any brand of battery. In fact, he’s already moved on to an improved second-generation version. It all started when the Wasilla, Alaska, resident found…
Read the complete story →From the archive · Full text
Feature story
Featured source:
A natural lubricant made from lanolin, the natural lubricant found in sheep’s wool protects against corrosion and lubricates better than petrochemical lubricants, according to the New Zealand manufacturers of Prolan. Environmentally friendly, it’s non-conductive, resistant to saltwater, acid…
Read the complete story →From the archive · Full text
Reader shop tip
Al McRoberts, 1218 S. 11 1/2 Road, Harrietta, Mich. 49638 (ph 231 389- 0231)
“I make new wheel rims for antique motorcycles that ride on clincher tires. Clincher tires were state of the art from 1904 until the mid 1930’s and had beads made from cord instead of wire, which allowed them…
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Conyers, Weatherford, Texas
“When needing to turn over an engine by hand, such as when adjusting valves or similar maintenance, many times there are obstacles in the way that prevent a straight ratchet handle from having room to swing. I got…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Shane Myrick, Pleasonton, Kan.
“I use an old refrigerator to store all my welding rods. But instead of using a light bulb to keep the refrigerator dry, as most people do, I use an old piano dryer. It’s designed to keep moisture…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Shane Myrick, Pleasonton, Kan.
“When I bought a new welding machine for my truck I thought the channel iron frame the welder was mounted on was too weak, so I used 4-in. dia. aluminum boxing to build another frame around the original…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
It’s a no-brainer to install a $35 to $40 part that can save thousands of dollars replacing a radiator. Tom Gano calls his coolant filter “the best radiator insurance you can buy”. He and his father, Lloyd, invented…
Read the complete story →From the archive · Full text
Reader shop tip
Carl Schultheis, Caro, Mich.
“I’m a 72-year-old retired dairy farmer. I sold my dairy herd in 1995, but I continue to run a farm shop. The fellow who rents my farm asked me if I had a solution to fix worn snapping…
Read the complete tip →From the archive · Full text
Reader shop tip
Danny Shaffer, Stillwater, Okla.
“Here’s a ‘handle’ that I came up with to put onto an ordinary ratchet handle. It keeps me from having to flex my wrist as much.
Read the complete tip →From the archive · Full text
Reader shop tip
Emery Beachy, Hardin, Mo.
“I’d advise any farmer to learn welding, by taking welding classes and practicing. Then invest in a good welder. My welder has saved me more money on repairs than anything else in my shop. Sometimes a welding repair…
Read the complete tip →From the archive · Full text
Reader shop tip
Frank Bloom, Dundee, N.Y.
“Whenever I throw away old jumper cables I always save the clamps. They work great for holding a straight edge for marking or for holding any small pieces while welding, etc.”
Read the complete tip →From the archive · Full text
Reader shop tip
James C. McGowan, Russell Springs, Ky.
“My 1994 Ford Explorer had a hole develop in a steel coolant line with anti-freeze in it. Replacing the line would have been costly and would have required a lot of work. Instead, I cleaned the line off…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Nichols, Galesburg, Ill.
“I fabricated this handy tool to help whenever I need to drill through round stock or tubing to allow the use of cotter or hairpins. I welded short lengths of angle iron to a steel plate and put…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Gary Kaspers of St. Peters, Mo., has a small welding shop in the corner of his garage.
Read the complete story →From the archive · Full text
Feature story
Featured source:
MIG, TIG and stick welders are all good ways to work with steel but once you try the new Multiplaz 3500, you might never go back to them. Not much larger than an old-time radio, all it needs…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“One of my customers and I were looking for a piece of steel in my storage racks a few years ago and couldn’t find what we needed,” says Carl Dressman, who owns a welding shop in Frankfort, Kan.
Read the complete story →From the archive · Full text
Reader shop tip
Rex Gogerty, Hubbard, Iowa
“We equipped our shop furnace with extra registers to get more heat into our main work space, which is about 40 ft. away. We cut and bend corrugated metal and anchored it above the furnace f a n…
Read the complete tip →