From the archive · Full text
Feature story
Featured source:
Martin Erickson doesn’t mess around when it’s time to crush a used oil filter or chemical can, paint can, etc. With 34,000 lbs. of crush-ing power, he flattens them like an armadillo on a Texas two-lane.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Brian Maring of Eddyville, Nebraska, spent only $1.50 and about two hours of time to make a tool that would cost him $300 to $350 to buy at a tire shop.
Read the complete story →From the archive · Full text
Reader shop tip
Dan J. Krenzel, Cullman, Ala.
“In re-sponse to Guy Ramsey’s comments in Vol. 28, No. 1 regarding GMC’s in-tank fuel pumps, I have a 1998 Buick Regal 308 Turbo. The car has a steel fuel tank and if you get condensation in it,…
Read the complete tip →From the archive · Full text
Reader shop tip
Kenneth Crumpton, 161 Tidwell Rd, Winfield, Ala. 35594
“My father, two brothers and myself are always building something in our farm shop.
Read the complete tip →From the archive · Full text
Reader shop tip
Paul Tannehill, Somerset, Penn.
“I have a 1982 Ford 1200 compact 4 by 4 tractor that is my handiest best buy ever. My only complaint was the lack of power steering. With a front-mounted hydraulic blade, steering could be quite a workout.
Read the complete tip →From the archive · Full text
Reader shop tip
Richard Ackerman, Columbia, S.Dak.
“I purchased an older 440 Bobcat with a bad engine. I overhauled it but it didn’t last long. I bought a new engine and before long I had to overhaul that one, too. Soon after, it blew up…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“It puts everything up high enough that I can service it easily,” says Harold Davis, Trenton, Tenn., about the service rack he built for his Deere garden tractor equipped with a 60-in., belly-mount mower.
Read the complete story →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Dan Jacobson, 8913 Weaver Lake Dr., Pequot Lakes, Minn. 56472
“This hydraulic welding table raises from 35 in. to 7 1/2 ft. high and will lift up to 1,100 lbs. To raise the table all I do is pump a foot pedal. To lower the table, I depress…
Read the complete tip →From the archive · Full text
Reader shop tip
David Novotny, Fargo, N. Dak
“I built a nice little bench grinder using a two-speed Westinghouse washing machine motor, some 2 by 12s, an old Chevy fan belt, a couple of pulleys, and a chuck from an old drill. The motor belt-drives the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Joe G. Eilert, Jewell, Kansas
“The press wheels on International Harvester 7100 drills are known for having the center break. You can repair them by welding a small plate to either side.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
John Porter, Albion, Mich.
Also, once the can is empty I slot the bottom of the can with a hack saw and dribble all the leftover product into a paint can. By mixing a bunch of different colors together, some surprisingly neat…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
I’ve never had a standby generator at my place so I always felt a bit vulnerable about power outages. I decided to mount a generator on our garden tractor, and we couldn’t be more pleased with it. It…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Our 1966 Ford pickup with 98,000 miles burned oil and the ring gear on the flywheel was going out. I bought a 1984 Chevy conversion van with a 6.2 diesel and dropped the sub frame out of it,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Some wives joke that their husbands live in their shops. Ed Yager, Glen Rose, Texas, re-ally did live in his for awhile, along with his wife, Gail.
Read the complete story →From the archive · Full text
Reader shop tip
Ben Kambeitz, Box 23027, Medicine Hat, Alberta, Canada T1B 4C7
“By making use of an old furnace fan and a pair of used tractor air filters, I was able to come up with a low-cost air cleaner for my shop. It’s a low-cost method of removing particles from…
Read the complete tip →From the archive · Full text
Reader shop tip
Clendon Nichols, Union, Ky.
After years of having tractor wheel rims rust out due to the corrosive effect of the calcium solution he put into the tires, Clendon says he finally came up with a rustproofing solution that works great.
Read the complete tip →From the archive · Full text
Reader shop tip
Harold C. Goodwin, Sr., Yulee, Florida
“This photo shows one of two handy, low-cost stands that I made for my chop saw. It works great for cutting pipe and rebar, etc. The base is an old brake drum filled with concrete. A length of…
Read the complete tip →From the archive · Full text
Reader shop tip
Pat Prom, Eden Prairie, Minn.
“I used 1/4-in. thick scrap metal to build my own 5 1/2-ft. high engine hoist. The hoist is raised and lowered by a 5-in. dia., 3-ton hydraulic cylinder. I use it to lift engines and transmissions out of…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Rust and corrosion on tire rims, valves, gauges, and pumps can now be prevented, thanks to a new patented, non-toxic, biodegradable product called Rim Guard Tire Ballast.
Read the complete story →From the archive · Full text
Reader shop tip
Chris Elliott, 4404 Breezy Point Road, McConnellsburg, Penn. 17233
“The rubber on the rolls on our Deere 1460 disc mower was coming off, which caused the machine to plug up. After pricing new rolls, we decided to fix the problem on our own. We stripped the rest…
Read the complete tip →From the archive · Full text
Reader shop tip
Donald Struckhoff, Augusta, Mo.
“The self-energized disc brakes on Farmall Super C to International 660 models tend to lock up after wet weather or whenever they’re not in use for a while. To solve the problem I put several squirts of gas…
Read the complete tip →From the archive · Full text
Reader shop tip
Donald Struckhoff, 5266 Hackmann Rd., Augusta, Mo. 63332 ph 636 228-4396
“The self-energized disc brakes on Farmall Super C to International 660 tractors tend to lock up after wet weather or if they haven’t been used for a while. Rust can form on the metal surface. I’ve found that…
Read the complete tip →From the archive · Full text
Reader shop tip
Rusty Olson, 2255 280 th St., Garner, Iowa 50438 ph 515 291-2082; email
[email protected]: “Don’t throw out your electrode (stick) welder. Some day you’ll be glad you still have it. Around our shop most things are built with ‘recycled steel,’ and while we do have a nice mig welder we’ve found…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
If you own an older Ford pickup with a rusted-out tailgate, you’ll be interested in this replacement tailgate that looks just like the original. It’s available from an Oklahoma company that specializes in classic pickup bed parts for…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Not many people build their own brake presses to bend sheet metal, but Wilfred Mollenbeck made a giant one with a 20-ft. wide bed. It measures 15 ft. high and weighs about 18,000 lbs. A hydraulic power pack…
Read the complete story →From the archive · Full text
Feature story
Featured source:
This new hydraulic-operated bench vise is as simple to use as stepping on a pedal. And, it doubles as a hydraulic press.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Eric Webster, Lansdowne, Ontario
“I made the frame of this hydraulic press out of old bulldozer parts. It runs off tractor hydraulics and has a ‘bed’ made out of a 6-in. wide, 3/4-in thick steel plate. The 6-in. dia. hydrau- lic cylinder…
Read the complete tip →From the archive · Full text
Reader shop tip
John Lindemer, Ind.
Several years ago, a neighbor of John’s had problems with frozen pipes. The problem was compounded by the fact that the frozen pipes were made of pvc instead of copper so he couldn’t use his welder to thaw…
Read the complete tip →From the archive · Full text
Reader shop tip
John Martens, Sanford, Man.
“I made a portable air-tool oiler out of some angle-iron and an old steering wheel. The wheel can act as a base or a handle.
Read the complete tip →From the archive · Full text
Reader shop tip
Lawson Products, Inc., 1666 E. Touhy Ave., Des Plaines, Ill. 60018 (ph 800 448- 8985; website
www.lawsonproducts.com): Lawson products has come up with a grinding disc that has three holes in it. When the disc is in motion the holes give you an accurate view of exactly what you are grinding. The company says…
Read the complete tip →From the archive · Full text
Reader shop tip
Pete Peters, Osler, Sask.
“I have come up with a stand that makes it easy to pour oil or other substances easily. It consists of an old wheel rim with a piece of steel pipe welded onto it. The strap iron bracket…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
It took Jacob May only about an hour to make a set of portable car ramps, using nothing but his cutting torch, welder and a bit of scrap metal.
Read the complete story →From the archive · Full text
Reader shop tip
Craig Richlen, Lockhart, Tex.
“I have successfully used “JB Weld” to do body work on my wife’s minivan and various other equipment. It’s an epoxy that can be used to hold any porous or non-porous surface. When I have a stripped screw…
Read the complete tip →From the archive · Full text
Reader shop tip
Darryl Foreman, Lafayette, La.
“I mount a roll of paper towels on hangers that attach to the frame on the underside of the trunk lid on my Buick Century car. That way I always have a towel handy to clean off my…
Read the complete tip →From the archive · Full text
Reader shop tip
Gene Pearson, Wichita, Kan.
“I bought two 24 by 20-in. stainless steel coolers from a local buffet restaurant. I put the coolers together and topped them with a 1/4-in. steel plate and they make some of the best workbenches I’ve seen.”
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Dan Jacobson, Pequot Lakes, Minn., doesn’t have a tailgate on back of his pickup. That’s because he often uses the pickup bed as a work table in the shop or field. One of his handiest tools is a…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Like all Case 850 crawler tractors, mine was difficult to steer. I added a pair of steering levers that make it steer as easy as a Caterpillar,” says Robert Gibson, Canby, Oregon.
Read the complete story →From the archive · Full text
Feature story
Featured source:
When Glenn and Gordon Marshalek, Raymond, Nebraska, needed to pull the engine and transmission from a garbage truck, they realized their normal engine hoist might not be able to handle it.
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you ever need to cut through concrete or rebar, you might be interested in this specially designed “wet cut” saw that can cut through concrete up to 12 in. thick, and even rebar.
Read the complete story →From the archive · Full text
Reader shop tip
John Orth, Greeley, Colo.
“I own a Bush Hog 60-in. Razor Back mower and had trouble with the trailing wheel shearing off just above the yoke that the wheel pivots on. To solve the problem, I welded two metal wings to the…
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Armstrong, Box 340, Point, Texas 75472 (ph 903 598-2855)
“Several years ago I knocked out the gearbox on my old Vermeer 605E round baler. My dealer said the company no longer made that gearbox and that I’d have to adapt a new gearbox designed for Deere balers…
Read the complete tip →From the archive · Full text
Reader shop tip
Bron Wentzel, Pivot Point, Box 488, Hustisford, Wis. 53034 ph 800 222-2231 or 920 349-3251; fax 920 349-3253; website
www.pivotpins.com): “Our company offers a wide variety of non-threaded fasteners including clevis pins, detent clevis pins, lynch pins, wire lock pins, tab lock pins, detent ring pins, positive lock pins, pull pins, ball plung-ers, ring pins, bent arm…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Friesen, Crooked Creek, Alberta
“I used to be in the fencing business and helped put up fences on game farms. To make it easier to do the job, I came up with this ‘wire twister’ that’s powered by a standard DeWalt 18-volt…
Read the complete tip →From the archive · Full text
Reader shop tip
Daniel Krenzel, Cullman, Alabama
“In your last issue I read the article by David Sheffield on carbonized rods. I remember as a young boy my dad welded up the worn drawbar holes on our tractor using hard surface welding rods and keeping…
Read the complete tip →From the archive · Full text
Reader shop tip
David Huppert, Ellsworth, Wis.
“I find that a length of 3 or 4-in. dia. PVC pipe makes a handy place to put my arc welding rod whenever my welder is running. It leaves my hands free to do anything. I cut the…
Read the complete tip →From the archive · Full text
Reader shop tip
Paul Miller, Belmond, Iowa
“Whenever the greaseless bearings go out on a roller on my round baler, I buy steel tubing from my steel supplier and press in new bearings. It costs less than 1/4 the cost of a new roller from…
Read the complete tip →From the archive · Full text
Reader shop tip
J.B. Gingrich, Inc., 169 Katherine St. N., RR 2, West Montrose, Ontario, Canada N0B 2V0 ph 519 664-3826)
“Our new angle rings are made from 10-ga. steel and have a seamless design. They’re available with or without holes and in black or galvanized steel. They can be used for ductwork or spouting.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Roger Wessels, Fairbury, Ill.
“The under-the-hood air cleaner on my Deere 4520 tractor was hard to get at so I replaced it with a big air cleaner off an old Allis Chalmers tractor. It consists of a big metal cylinder that I…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Rea, Salem, Ohio
“I’ve had problems breaking axle bolts on my Case 1845 Uni-Loader. Replacing the bolts is tough because I can’t get my hand into the holes to install them. I called the dealer and was told to pull the…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
When the bottom rings on his round bale feeders began rusting through, Art Freymiller, Woodman, Wisconsin figured he could repair them himself.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Lyndal Hatton, DeBerry, Texas, came up with an inexpensive solution to a problem he had with his New Holland 616 mower.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Lloyd Meffert, Hettick, Ill., does repair work for area farmers. When he heads out on a call, he always takes his home-built, 2-wheeled “repair trailer”.
Read the complete story →From the archive · Full text
Feature story
Featured source:
You wouldn’t think some tools could ever be improved but there’s always someone willing to try. The Weight Forward Hammer is a new version of one of man’s oldest tools from a company that’s been making hammers since…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bob Moty, Crystal Lake, Ill.
“I made a couple modifications to make my auto ramps more useful. The first was reinforcing them on the sides with some scrap steel. Next, I bolted 8 by 12-in. pieces of belting onto the lower ends of…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Bob Moty, Crystal Lake, Ill.
“I have also come up with an easy way to mark logs while cutting firewood. I took 2 pieces of 1-in. diameter shaft, 5-in. long and ground them to a point. Next, I welded a piece of 1-in.…
Read the complete tip →From the archive · Full text
Reader shop tip
David Shaeffield, Repair Tech, 1434 E. Benge Rd., Fort Gibson, Okla. 74434 (ph 888 478-4558)
“I have come up with a valuable set of tools that can be used for a variety of different things. I sell sets of carbonized steel rods through Repair Tech that can be used when welding hitch holes…
Read the complete tip →From the archive · Full text
Reader shop tip
Farmchains.com, 105 S. Peoria Ave., Dixon, Ill. 61021 (ph 800 648-5429; fax 815 288-6790; website: www.farmchains.com)
This new website offers a wide variety of tractor, header, roller chains, steel chains, and other miscellaneous agricultural attachment accessories. The costs are often much lower and they say they offer the widest selection on the web. If…
Read the complete tip →