Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 21, No. 1 (1997)

Vol. 21, No. 1 (1997)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–32

36 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Bruce Klemm

Bruce Klemm, Whitelaw, Wis.

“We decided our 1975 4366 International 4-WD drive tractor would be a lot more useful if it had a 3-pt. hitch instead of the drawbar hitch it came equipped with. However, we ran into two problems. International 3-pt’s are scarce because only about 1,000 of these tractors were ever equipped with them. And, when you can find one at a salvage yard, it’ll likely cost over $1,300.

“We discovered that 3-pt. hitches for Case 4-WD’s are more plentiful and are priced around $850. So we bought a Case 3-pt. from a salvage yard and adapted it to fit our International tractor. It was a surprisingly simple project.

“The main subframe of the Case 3-pt. required that two half-moons be cut out of the top rails to clear the axle housings of the 4366. We fabricated mounting brackets for the subframe and welded a 2 1/2-ft. wide by 2-ft. high plate made of 3/4-in. thick flat plate across the back of the tractor. It was pre-drilled to accommodate the top link brackets. We shortened the drawbar support by 3 in. on each side and welded it in position about 4 in. higher than the Case drawbar support had been. We plumbed it up simply adding an extra valve to the tractor’s external hydraulic system.

“We’re extremely pleased with the out-come. We’re now able to pull an 8-shank subsoiler with the 4366 and we plan to buy a semi-mounted plow. Best of all, it easily adds $4,000 to $5,000 to the resale value of the tractor. I’d be happy to share how-to info with anyone interested.”

Contact: Bruce Klemm, 9008 Meier Rd., Whitelaw, Wis. 54247 (ph 414 732-4592).

From the archive · Full text
Reader shop tip

Nick Dengler

Nick Dengler, Middletown, Ohio

“We carry the most complete line of parts for Deere 2-cylinder tractors in the U.S., and we’ve filled orders from every corner of the world. We have virtually every part (used, rebuilt, remanufactured, or newly built and improved) for virtually every Deere 2-cyl. ever built, from the 1918 Waterloo Boy to the 840’s built in 1960. Our inventory fills 40,000 sq. ft. of indoor storage area. Even sheet metal parts, which are the most frequently requested, are stored inside.

“Our newest remanufactured part is a belt pulley wheel for models A, B, 50, 60, 620 and 630 and 520 and 530. The wheels are built to exact O.E.M. specs. We remove the easily breakable cast clutch latching dog pivot tabs and replace then with six solid steel pivot tab weldment units. The pin holes in these new tab units are virtually indestructible. Rebuilt wheels are always in stock, ready for immediate shipment on an exchange basis. Or, if you prefer, we’ll re-build your pulley wheel and return it to you. Cost is $445.”

Contact: Dengler Tractor Inc., 6687 Shurz Rd., Middletown, Ohio 45042 (ph 513 423-4000 or 0706).

From the archive · Full text
Reader shop tip 1 of 2

W.A. Gibbs

Individual tip 1 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.

“Here are a few shop-built tools I can’t do without.

“This is the slickest way ever to easily and safely remove pulleys. Works better than conventional two and three-jaw pullers. The tool consists of a hydraulic jack, two chains, a piece of round stock steel, and a couple of pieces of flat steel - one with a hole drilled in the center and each end. You bolt the pulley to the holes drilled in the ends of the flat steel, matching up the crankshaft to run through the hole drilled in the center. You put the piece of round stock between the end of the crankshaft and the bottom of the jack. Then run chains around the piece of steel attached to the pulley. Ends of the chains attach to a heavy piece of flat steel plate welded to the ram on the jack.

This set-up allows you to pull the pulley while staying clear of any potential flying parts.

“I used this method to pop the pulley off a crankshaft on a 2-ton truck equipped with 6-cyl. engine by removing the radiator and grille. This tool can be adapted to many other jobs by modifying the steel plate and chains to fit the job.

From the archive · Full text
Reader shop tip 2 of 2

W.A. Gibbs

Individual tip 2 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.

“I also built this drill press out of scrap steel, using a jack with a bad shaft. I mounted it in a channel iron and flat steel frame about 5 ft. tall. I use it for many small jobs, such as pressing bearings onto shafts. Press height is adjustable from about 1 ft. to 4-ft. It only cost about $20 to build and works great.”

From the archive · Full text
Reader shop tip

Jeff Roberts

Jeff Roberts, Needville, Texas

“Not long after I bought an old Deere 60 planter with round fiberglass hoppers, I began to notice wear spots where the hoppers rubbed against toolbar brackets every time I lifted the planter. Soon the hoppers were badly cracked; one even had a large triangular hole in the bottom.

“To fix the problem, I used auto body filler, or Bondo to reseal all the worn-open cracks. To fix the large holes, I cut a piece of nylon window screen (aluminum would work too) and ‘super glued’ it into position over the hole. I applied Bondo over the hole thickly and worked it gently into the screen from both sides. The Bondo cost only about $10 and worked great. It should last longer than ordinary fiberglass repair kits and was a lot cheaper than buying new hoppers.”

From the archive · Full text
Reader shop tip

James S. Wilson

James S. Wilson, Celeste, Texas

He used a tractor rim off an old “B” Farmall to build a forge for his welding shop.

“I cut the 2-ft. dia., 10-in. deep rim in half around the middle and discarded one half. I welded a 1/4-in. thick steel plate under the remaining half. I lined the inside of the rim with firebrick, sloping inward like a funnel to a 3-in. dia. opening at the bottom. I placed a 3/8-in. thick plate on top of the firebrick and drilled 1/4-in. dia. holes 1/2 in. apart in the plate, like the pattern on a Chinese checkerboard. This allows heat from the coal I burn in the fire box to radi-ate up.

“A 3-in. dia. electric squirrel cage fan blows air into the fire box. I made a metal flapper for the inlet of the squirrel cage to control air flow. The forge mounts on 38-in. tall legs and there’s a door on the bottom to dump the ash.

“I can heat 3/4-in. thick plate steel to red hot in 10 to 15 minutes much more cheaply than I could using an acetylene torch. The only improvement I’d make is to use a bigger squirrel cage, one with a 6 or 8-in. fan, for better efficiency.”

From the archive · Full text
Reader shop tip

Richard Day

Richard Day, Neligh, Neb.

“You can start cold tractors and combines with what I call ‘jumper hoses’ that circulate hot coolant from a warmed-up engine to the cold one. You need two lengths of heater hose. Just cut the heater hose on the ‘starter’ vehicle, such as your pickup, and install a 2-way quick-tach hydraulic coupler. When you need to start a machine, run the hose to the heater hose on the water pump on the cold vehicle. Simply repeat the process with the other length of hose, running one end from the heater on the cold vehicle to the heater on the starter vehicle. One note: be sure heaters in both vehicles are turned on. By the time you’ve had a cup of coffee, warm water has been circulated through the cold engine so it pops right over. Works great. I wish I’d known about it 20 years ago.”

From the archive · Full text
Reader shop tip

Melvin Carlson

Melvin Carlson, Buffalo, Kan.

Melvin’s come up with a slick way to convert old AC welders, ranging in size from 0 to 500 amps, to DC to reduce splatter and get more penetration with a smoother weld.

“I’ve converted my three Lincoln TM 300’s as well as a couple of my neighbors’ Lincoln 225’s,” he says.

“I make a box out of 3/8-in. thick plate steel that attaches to the bottom of the welder and houses the new components. It has caster wheels so you can roll the welder around.

“I install four 500 amp diodes (smaller ones would probably work, too) to make a bridge diode. It mounts on an aluminum heat sink to keep it cool. I insulate the heat sink from the welder’s frame with insulating board or rubber. I insert a current stabilizer on the negative line to smooth out the flow of current.

“I make conversion kits for $225 FOB.” Contact: Melvin Carlson, Mortgage Hill Farm, Box 66, Buffalo, Kan. 66717 (ph 316 537-6590).”

From the archive · Full text
Reader shop tip

Dennis Kees

Dennis Kees, Harlan, Ind.

“The trouble with the 3-in. twisted spikes on our 9-shank Glencoe soil saver was that in bringing up soil and residue in hard ground they tripped a lot, eventually wearing them down at the neck and breaking them off. We solved the problem by replacing them with 10-in. sweeps and 2-in. wide, 1 1/2-in. thick straight chisel plow shanks, which simply bolt with a 3-in. bolt right through the sweep onto the shank. They work great for holding sweeps down when breaking up hard pan and they wear at least twice as long. Commercial kits are available to do much the same thing, but they’re extremely difficult to install and cost about $40 per shank. The straight spikes we used cost $13 apiece; the sweeps $10 apiece.”

From the archive · Full text
Reader shop tip

Jack Gardiner

Jack Gardiner, Ilderton, Ontario

“The moldboards on my International 710 plow had holes worn through them near the center next to the shins. I found a way to keep the moldboards from wearing so that they last a lot longer - whenever I replace the points and shins I reuse the old shins. Since the old shins are shaped the same as the moldboards everything looks custom made. I remove the bottom bolt from the moldboard near the shin. I use a longer bolt to fasten the old shin through the bottom hole onto the moldboard. Then I put a bead of weld on top of the old shin and moldboard. The old shin is sort of layered over the edge of the new shin (about 1/4 in.) and over the moldboard. This adds a lot of metal right where most of the wear occurs on my moldboard. Now my moldboards seem to last forever.”

From the archive · Full text
Reader shop tip

Alan Linda

Alan Linda, Rt. 3, Box 83, New York Mills, Minn. 56567.

“Does anyone out there know how to stop an IH “Super” series tractor? I’ve got a super MTA but I don’t think it matters which Super model it is. They won’t stop. I even tried installing new brake assemblies. Those were the only brakes I’ve ever seen wear out in the shed. If anyone knows how to fix them right, please write.”

From the archive · Full text
Reader shop tip

Leland Jordal

Leland Jordal, Mexico, New York

“I made this spring-loaded, fold-down exhaust pipe for my tractor. Now, if the pipe hits a tree branch or other low-lying obstacle, I don’t end up with a broken or cracked manifold. It consists of two L-shaped pipes. One comes up out of the tractor hood from the manifold. The bottom of the ‘L’ on the top pipe fits loosely over the lower pipe, so it pivots back and forth in line with direction of travel. I put a door spring in front and back of the pipe, so if I hit anything, the pipe springs right back up.”

From the archive · Full text
Reader shop tip

Thomas Dale Martin

Thomas Dale Martin, Omaha, Neb.

“The traction drive pulley on our Gleaner K combine kept wearing out bearings. Finally, we solved the problem by having a machine shop turn the outer hub for the outboard bearing, which we anchored around the front axle with plate iron. Provides extra support for shaft bearings.”

From the archive · Full text
Reader shop tip

Eugene G. Johnson

Eugene G. Johnson, Rapid River, Mich.

“Making large holes in thick steel often re-quires the use of large, expensive power tools. A simple, inexpensive way to cut holes is to make a compass attachment for your cutting torch. Sharpen the end of a 7-in. pole barn spike to a smooth point and make a bend in the spike (as shown). Then flatten the end of a 5/16-in. bolt and drill a hole in it the size of the spike. Slide this through the space between the torch pipes, placing a washer on either side of the pipes and tightening the nut when you have the spike adjusted to the radius you want.

“To aid in adjusting the radius, find a medium size electrical wire connector and substitute a short 5/16-in. fine thread bolt for the standard set screw. Use a short piece of wire that fits the oxygen hole in the cutting tip. Bend a short 90 degree angle in the wire and slide the wire connector to get the exact radius. You can drill a small hole at the edge of the hole to start the cut. Center-punch the hole and place the point of the spike in it. I do the work on top of a small oil barrel with an old tire rim on top so that I can walk 360 degrees around the piece I’m cutting while holding the torch.”

From the archive · Full text
Reader shop tip

Arne Eissner

Arne Eissner, Souris, Manitoba

“When one of the tie rod balls on the adjustable front axle on my Deere 6030 tractor wore out, I discovered that replacing it would cost me about $320. I was able to save a lot of money by adapting a tie rod ball that was designed for my Deere 5010 tractor. I already had the part on hand as a spare and paid $108 for it.

“I used a grinder to grind off the weld between the tie rod ball and threaded steel shaft, then unscrewed the old tie rod ball from the threaded shaft and screwed in the new one. Then I welded the two parts together for safety. The job took only about 30 minutes. The reason it costs so much to replace tie rod balls on the 6030 is that the tie rod ball and threaded shaft are built and sold as one piece, whereas units designed for the 5010 are built and sold separately.”

From the archive · Full text
Reader shop tip

Jim & Roger Koppes

Jim & Roger Koppes, Medina, Ohio

“Here’s a time-saving revision we’ve made to strap ratchets on our flatbed bale-haul-ing trailers. By welding a 1/8-in. piece of flat stock onto the end of the ratchet and cutting a 3/8-in. square hole in the center, I can insert a 3/8-in. drive on a cordless drill to rewind the 27-ft. strap in just seconds. A handy timesaver.”

From the archive · Full text
Reader shop tip

Travis Cooper

Travis Cooper, Ill.

He made a handy shop stool that rolls on four gauge wheels off a Deere cultivator. The stool stands about 18 in. high. The frame is made from various pieces of scrap metal. Cooper likes the stool because the wheels are wide and stable, even on uneven surfaces.

From the archive · Full text
Reader shop tip

Roland Beckmeyer

Roland Beckmeyer, Hoyleton, Ill.

When Roland decided to add flashing safety lights to the back of his machinery, he decided to use battery-operated units rather than running wire to operate 12-volt lights. This way he can transfer one set of lights between various pieces of equipment.

What he did was to build small wood boxes that fasten to the back of grain boxes, and other equipment. The light simply sets inside the box. A single bolt is inserted through the front of the box and through the light to hold it in place.

From the archive · Full text
Reader shop tip

J.R. Kellogg

J.R. Kellogg, Boise, Idaho

“Here’s an idea that saves me a lot of time working with socket sets. I use colored electrical tape to color-code the sockets so I can tell at a glance the size of each socket. It takes a while to learn what color represents what size, but you can use the system on other tools, too, such as open end wrenches. Here are the colors I use for each size; Orange - 3/8-in.; Yellow - 7/16-in.; Green - 1/2-in.; Red - 9/16-in.; White - 5/8-in.; Black - 11/16-in.; Blue - 3/4-in.”

From the archive · Full text
Reader shop tip

John C. Blundell

John C. Blundell, Papakura, Auckland, New Zealand

“Here’s an automatic air bleed valve I designed to pre-vent air lock in long water pipes. A short length of pipe runs straight up from the main pipe. There’s a vent hole in the top of the pipe which is closed by a float when the main water pipe is full of water. If an air bubble comes along, the float drops, allowing the air to escape.”

From the archive · Full text
Reader shop tip

Elroy A. Johnson

Elroy A. Johnson, Michigan, N.Dak.

“I automated the chute on my snow blower with a 6-volt header lift motor off a Massey Harris 21A combine. I mounted it on the chute and wired it up to a pair of switches so I can turn it left or right, as needed. Works good.”

From the archive · Full text
Reader shop tip

John Steinberger

John Steinberger, Kenmare, N.Dak.

“I’ve found that wiring on tractors is almost always inadequate for the amount of equipment we’re trying to run off it. I run heavy gauge wire from the battery to a homemade ‘bus’ in the tractor cab, and then use lighter wire to go to my monitors and other electrically-powered equipment.”

From the archive · Full text
Reader shop tip 1 of 3

Clark Dysle

Individual tip 1 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.

“Our 1987 Ford 250 diesel pickup is strong and runs good but the hydraulic clutch is poorly engineered. The master and slave cylinders are made out of plastic and wear out about every 50,000 miles. The cost to replace them is around $200. I solved the problem by installing 1960 Ford master and slave clutch cylinders in the truck. It works but needs a strong left leg to operate.

From the archive · Full text
Reader shop tip 2 of 3

Clark Dysle

Individual tip 2 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.

“When welding thin steel I use a stainless rod with A.C. power. It seems to flow without blowing a hole in the thin metal. It’s much faster than gas welding and less heat is used, presenting damage to the parts you’re working on. One hint: use short bursts of power.

From the archive · Full text
Reader shop tip 3 of 3

Clark Dysle

Individual tip 3 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.

“To safely change the rear transmission on my 10-yard dump truck, I built a wood frame that goes just behind the cab, and I hung a chain and come-along from both the wood frame and from the hydraulic dump cylinder.”

From the archive · Full text
Reader shop tip

Rodger Parmelee

Rodger Parmelee, Valier, Mont.

“I made a ‘sizer’ to mount on the side of my cut-off saw that saves a lot of time when cutting several pieces the same length. It slides back and forth on a piece of pipe that sticks out from the side of the saw table. A locking collar holds the ‘ear’ in place. You measure the desired length with the ear up, then turn the ear down out of the way before cutting so material that’s being cut does not bind. Then turn the ear up for the next piece. It will cut lengths up to 3 ft. long. When not in use, it is completely out of the way. I’ve been making these for sale for $30 to fit any cut-off saw with two bolts. Contact: Rodger Parmelee, Box 155, Valier, Mont. 59486 ph 406 279-3516.”

From the archive · Full text
Reader shop tip 1 of 2

Leonard J. Arenz

Individual tip 1 of 2 from this reader’s published contribution.
Leonard J. Arenz, Streator, Ill.

“The drive chain on the rotary screen on the radiator on my 510 Massey combine kept breaking. I read an article in FARM SHOW about a farmer who had the same problem. I called the man and did what he did, putting an air-drive screen off an IH 715 combine on my Massey. It completely solved the problem. Works perfect. Massey should make this solution available.

From the archive · Full text
Reader shop tip 2 of 2

Leonard J. Arenz

Individual tip 2 of 2 from this reader’s published contribution.
Leonard J. Arenz, Streator, Ill.

“I repaired an exhaust leak on the combine with a muffler tail pipe bandage. For about $3.00 it worked great and saved a lot of money over replacing the pipe.”

From the archive · Full text
Reader shop tip

Norman Foellmi

Norman Foellmi, Sparta, Wis.

“I’ve discovered a new use for my wood splitter. I bent the forks on my bale loader and needed a way to straighten them out. I laid a railroad tie across the splitter, put the bent fork against the tie, and applied pressure with the splitter ram. It did a beautiful “straightening” job.

“Soon after I bent 3-in. dia. pipe axle on a farm trailer. It straightened easily. I was amazed at the power the ramp delivered.”

From the archive · Full text
Reader shop tip

Charles Smart

Charles Smart, Shellbrook, Sask.

Charles built a hydraulic shop press that attaches to a punch press so he could repair the housing on his 27 1/2-ft. 4153 Will Rich air seeder.

“I’ve never seen a commercial hydraulic press that can be locked so precisely in place,” he says.

“I built a rigid frame out of 3 by 5-in. tubing and used 1/2 by 3-in. flat bar steel for uprights so there’s absolutely no play in the columns. I mounted a Williams four-piston hydraulic pump off a grain truck hoist on top of the 8-ft. high upside down A-frame, which is trussed on top. I use a 1 1/2 hp electric motor to drive the pump, which connects to a hydraulic cylinder I made myself. The cylinder, which will accommodate punch sizes up to 1 1/4 in., can be adjusted from side to side with C-clamps. This way I can vary spacings of holes. I used 7-in. heavy wall channel iron to make the pressing bed. I made a 10 by 12-in. die plate out of 1-in. T #1 steel to adapt the press to punching steel.

“The unit mounts on a two-wheel cart fitted with 400 by 8 in. lawn mower tires so I can push it around my shop or even use it as far outside as an extension cord will reach.

“I haven’t tested its full capacity, but I’ve punched 1 in. dia. holes in steel plate up to 1/4-in. thick with it. My guess is that this job required only about half of the pump’s 3,500 psi capacity.”

From the archive · Full text
Reader shop tip

Bill Irwin

Bill Irwin, Glade Valley, N.C.

“It seemed like the longer we used our fuel-powered space heater, the worse it would smell. I think it was from burning the same air over and over. I solved the problem by venting in outside air using a 10-ft. length of flexible plastic drain line. It runs from the back of the heater out through an outside wall. Now there’s no smell at all.”

Shop feature stories

From the archive · Full text
Feature story

“Pressure Handle” Takes The Work Out Of Drilling

Featured source:

“It’s especially handy when drilling from underneath in close quarters,” says the manufacturer of the “Pressure Handle” that installs on any portable electric or pneumatic drill.

It lets you chain the drill up to whatever you’re working on in order to support the drill’s weight. It also pulls the drill into the hole. You simply remove the existing handle and screw in the pressure handle. Fasten one end of the chain around what you’re drilling, and run the other end over a slotted wheel on the handle. Twisting the handle slightly causes a gear mechanism to crank up the chain, which pulls the drill toward the work.

“The drill requires very little pushing by the operator. It’s especially handy for drilling big holes,” says Carl Geiser.

“It’s been available since 1945 but isn’t well known because we’ve never advertised it and have no distributors.”

Sells for $129.95 plus S&H. Contact: FARM SHOW Followup, Pressure Handle Co., 399 Hughes St., Swoyersville, Penn. 18704 (ph 717 288-5282).

From the archive · Full text
Feature story

“Fast Way To Remove Studs”

Featured source:

Here’s the fastest, safest tool ever designed for removing “headless” studs, according to Trycon Technologies, manufacturer.

The “Stud Remover” is a sort of socket set that fits on any standard air impact wrench to remove studs up to 6 in. in dia. The torque from the wrench combines with a high frequency vibration that works the studs loose. The “suction” sockets grip tight with no damage to the threads.

Available in standard 3/8, 7/16, 1/2, 5/ 8 and 3/4-in. dia. sizes, beginning at $89.95. Set of five sells for $495. (Special order sizes up to 6 in. available on request).

Contact: T r y c o n Technologies Inc., P.O. Box 5 2 0 , P a d u c a h , Texas 79248 (ph 806 492-3542; fax 3250).

From the archive · Full text
Feature story

Repowered Skid Steer Fitted With Plymouth Car Engine

Featured source:

When the Wisconsin 4-cyl. air-cooled engine wore out on his Bobcat 620 hydrostatic drive skid steer loader, Lyle Wolle, Truman, Minn., replaced it with a 4-cyl. liquid-cooled engine out of a 1982 Plymouth Omni.

“It put new life into a well-built machine. It has more power than ever,” says Wolle, who repowered the loader two years ago.

“My total cost was less than $900 and the entire job took only about a week to complete.

“I bought the Bobcat used about 15 years ago with 1,500 hours on it. It now has over 4,000 hours. I spent about $1,500 to overhaul the original Wisconsin engine a number of years ago. When the engine died a second time, I didn’t want to spend the money to rebuild it again because it wouldn’t have increased the value of the machine. I measured the engine compartment and began looking for a new engine. I settled on the Chrysler 1.7-liter because it’s a tough little engine that sells for a reasonable price. I paid $250 for the Omni and pulled out the engine. I can replace the new engine if it ever goes bad for a fraction of the cost to rebuild the Wisconsin engine.

“I didn’t have to make any major modifications. I rerouted the gas fill tube and some of the throttle linkages, built new motor mounts, and adapted the engine wiring harness to the loader’s electrical system. The loader’s hydrostatic pump is direct-driven off the crankshaft just like on the original engine. However, I had to have an adapter made so that I could bolt the pump directly to the engine’s timing belt sprocket which bolts onto the crankshaft. The new engine has a lot more power than the old one so I didn’t have to install a governor. I used the car’s ac-celerator when hooking up the throttle linkage.

“The Wisconsin engine had 30 hp but the Plymouth engine has 60 to 70 hp. It’s just as fuel efficient but has more working capacity due to the extra power. I never run the engine over 3,600 rpm’s to keep from damaging the hydraulic pumps. The loader was originally designed to lift 1,100 lbs. but can now lift about 1,300 lbs. I added about 400 lbs. to the rear end to compensate for the extra lifting capacity.

“The new engine has an electronic ignition and is liquid-cooled instead of air-cooled so I mounted the car’s radiator above the engine compartment and mounted an electrically-operated fan on top of the loader frame behind the cab. I had the exhaust pipes custom fabricated at a muffler shop and rerouted them out the back end to keep exhaust fumes away from me. The new engine is a lot quieter than the old one. I lengthened the engine access cover by 4 in. to accommodate the new engine’s flywheel and starter wheel.

“I think any Chrysler 1.7-liter engine would work. There are a lot of these engines around and they have a lot of life left in them.”

Wolle says he’s willing to repower other Bobcats on a custom basis.

Contact: FARM SHOW Followup, Lyle R. Wolle, Rt. 3, Box 135, Truman, Minn. 56088 (ph 507 776-4737).