From the archive · Full text
Reader shop tip
Avre Papst, Fullerton, Neb.
“There are a lot of ways and a lot of products available to treat corrosion on battery posts, but there’s nothing else like the product I sell. When used as directed, one application will prevent corrosion on posts…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Don Williams, Clarinda, Iowa
“I’ve found that by filling an oil filter full of oil before installing it on engines brings oil pressure up faster because it doesn’t have to travel through the filter before reaching the bearings. This reduces wear on…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Don Williams, Clarinda, Iowa
“I also built a tire bead-seating tool similar to some commercial models available, but for a fraction of the cost.
Read the complete tip →From the archive · Full text
Reader shop tip
Franklin Pacey, Miltonvale, Kan.
Franklin uses a handy tractor-mounted air compressor to blow dirt off radiator fins and air up low tires in his custom-baling business.
Read the complete tip →From the archive · Full text
Reader shop tip
Henry A. Kubischta, Dickinson, N. Dak.
The fuel tank on Henry’s late 1970’s 170 Allis-Chalmers tractor didn’t come equipped with a screen and that caused frequent headaches.
Read the complete tip →From the archive · Full text
Reader shop tip
Josh R. Hofer, Ponteix, Sask.
Josh came up with this simple-to-build truck box brace that keeps sides from bowing while hauling heavy loads. He’s used it on both his 1990 Ford and 1975 Chevy 3-ton trucks equipped with 8 1/2 by 16-ft. Midland…
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Albrecht, Prelate, Sask.
Ken says Deere combine pickups are the best ever built, but the stamped tin flanges on the end of the castor wheels cause problems.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Robert House, Grace City, N. Dak
“If a bolt breaks off in the head of an engine you’re overhauling, you can remove it quickly and easily like this.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Robert House, Grace City, N. Dak
“I also always brush Permatex anti-seize lubricant on new bolts when I’m putting engines back together. They come out much easier the next time.”
Read the complete tip →From the archive · Full text
Reader shop tip
Rod Rhoades, North Star, Alberta
Rod discovered a simple, no strain method of driving nails with an air hammer fitted with a straight punch attachment.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Chop Gibson, Scranton, Iowa
“I have a Sukup bin unloading auger that had trouble with the roller chain which kept jumping off. I replaced the sprockets with larger ones to try to solve the problem. It worked.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Chop Gibson, Scranton, Iowa
“I built a cart in my shop for a hauling bulk oil barrels. I installed a pump on the barrel so that when I changed oil, I pushed the cart over to the tractor or vehicle to pump…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Dan Petersen, Curtice, Ohio
“I need help. The battery on my Massey Ferguson 180 tractor won’t charge. Everything electrical has been replaced, from the alternator to the gauge. It still won’t work.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Dan Petersen, Curtice, Ohio
“I use a $2 notebook to keep track of equipment maintenance. I divided it into sec-tions for everything from the lawn mower up to the combine. I write down everything I do except for adding fuel. As we…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Eugene Alt, Audubon, Iowa
“We replaced the steel tube on our Deere planter’s cross auger with a piece of 6-in. dia. pvc pipe.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Eugene Alt, Audubon, Iowa
“One handy idea we use in our shop is to wire a length of heavy extension cord directly to a wall outlet. We curl up the cord and hang it on the wall. That way it’s always there…
Read the complete tip →From the archive · Full text
Reader shop tip
George “Bing” Ribble, Hettick, Ill.
“I built this high pressure washer out of a re-built compressor from a local car wash. It’s powered by a 5 hp electric motor off an old silo unloader. I added a second pulley to the compressor to…
Read the complete tip →From the archive · Full text
Reader shop tip
George Holsapple, Jewett, Ill.
George uses old bags of seed corn as a cheap source of fuel to heat his 54 by 54-ft. shop. He burns the corn in a three-year-old A-Maize-Ing Heat furnace (Big M Mfg. Co., R.R. 3, Box 319A,…
Read the complete tip →From the archive · Full text
Reader shop tip
Gregory L. Reif, Claflin, Kan.
“I needed a transmission jack but couldn’t jus-tify a new one so I built my own. I used two pieces of 3/8-in. thick steel plate - one 18 by 18 in. and the other 10 by 10 in.…
Read the complete tip →From the archive · Full text
Reader shop tip
Levi Adams, Locke, N.Y.
“I’ve discovered that pto shafts run better if you do not grease them as much as the rest of the machine it’s mounted on. Usually once for every three or four times is sufficient.”
Read the complete tip →From the archive · Full text
Reader shop tip
Paul Knauer, Elizabeth, Ill.
“After the 407 cu. in. engine blew up in our late 1960’s IH 856 tractor and ruined the crankshaft, we decided that the cost of a new crankshaft and a complete overhaul - at about $6,500 - was…
Read the complete tip →From the archive · Full text
Reader shop tip
Stephen Painter, Lomax, Ill.
He made a chain oiler for his New Holland cornhead using a piece of 4-in. dia. pvc pipe. He capped each end and installed a 12-volt spray valve in one end. He fills the pipe with oil. A…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Gil Wammen built a portable pipe bender that he uses to make corral panels and legs for feed bunks. The Reva, S. Dak., farmer says it works as well as anything he could have bought.
Read the complete story →From the archive · Full text
Reader shop tip
Dan P. Snyder, Odebolt, Iowa
Dan had trouble remembering to shut the engine compartment door on his 1990 Deere 9500 combine whenever he opened it during harvest. So last summer he rigged up an automatic door closer for his combine that’s adaptable to…
Read the complete tip →From the archive · Full text
Reader shop tip
Gordon Rice, Clarion, Pa.
“We carry the world’s largest selection of new replacement parts for older IHC tractors. We stock over 8,000 parts for tractors built between 1921 and ‘39.
Read the complete tip →From the archive · Full text
Reader shop tip
John C. Porter, Columbia, Tenn.
“We restore ‘paper pulleys’ on antique tractors to like new condition. All you do is send us your old pulley and we do the rest.
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Campbell, Coarsegold, Calif.
“In our part of the country, there’s a lot of iron in the water and, consequently, household water filters typically don’t last more than a month. However, I’ve found a way to double the life of the carbon…
Read the complete tip →From the archive · Full text
Reader shop tip
Vaughn Havens, Bath, N.Y.
Vaughn built three or four swivel mounts for fluorescent lights to light up even the darkest corners of his 30 by 60-ft. shop.
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“Our new electronic ignition kit for older model tractors allows gas to be burned more efficiently and eliminates the need to change points,” says Jim Lee of CBS Performance Automotive, Colorado Springs, Colo.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“You can set up a portable mini workshop on any pickup equipped with a square bumper hitch receiver, allowing you to do a variety of jobs right in the field,” says Joe Locklear, Locklear Electric, Inc., Wood River,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
After Ray Hosselton installed a new milling machine in his shop, he discovered he needed a way to lift heavy parts up into position for repair.
Read the complete story →From the archive · Full text
Reader shop tip
Ben McIntyre, Harwood, N. Dak.
Ben’s company, Big Tractor Parts, specializes in new and used replacement parts for Steiger tractors.
Read the complete tip →From the archive · Full text
Reader shop tip
Douglas McKenzie, Stony Plain, Alberta
“I would like to follow up on my article, ‘Working With Diesels In Ford Pickups’, because of all the letters I’ve received asking for advice since it ran in your last issue.
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Guarino, Alden, N.Y.
If you need a wiring harness for an older model tractor, you’ll want to check out Jim’s business, Agri-Services, which specializes in making like-new wiring harnesses for antique tractors and other equipment.
Read the complete tip →From the archive · Full text
Reader shop tip
John Cooke, Monroe, Conn.
“When I got tired of hitches twisting on my drawbar, I bent a piece of 1/4 by 2-in. scrap iron into an inverted V shape with a flattened apex. I torched a 3/4-in. dia. hole in the flat…
Read the complete tip →From the archive · Full text
Reader shop tip
Myrna Nuese, Marshalltown, Iowa
Myrna’s company, Hawkeye Sales, offers top link cylinder adapters for Cat. II and III 3 pt. that let you angle or level loads from the seat of your tractor.
Read the complete tip →From the archive · Full text
Reader shop tip
Perry Bemis, Wichita, Kan.
“Want to add wheel alignment capability to your shop but can’t justify the expense of conventional equipment?
Read the complete tip →From the archive · Full text
Feature story
Featured source:
For about $30 you can build a 6-ft. high portable service light that can be used anywhere because it operates off the battery of any vehicle, says inventor Kirk Harrold.
Read the complete story →From the archive · Full text
Feature story
Featured source:
When Nebraska farmer Steve Hietbrink tore down a pair of 40 by 90-ft. chicken houses, he saved the aluminum roofing and all salvagable wood to build a 60-ft. wide, 104-ft. long machine shed and shop. In the process,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
You can sweat pipe joint in seconds with new double and triple flame torch tips that concentrate the flame directly on the pipe with no damage to the surrounding area.
Read the complete story →From the archive · Full text
Reader shop tip
Carroll Kerley, Peck, Kan.
Carroll came up with a low cost way of repairing the openers on his Deere 494 4-row planter.
Read the complete tip →From the archive · Full text
Reader shop tip
Darrell Cranfill, Hillsboro, Ill.
There are a couple of Midwestern companies that specialize in recovering old tractor steering wheels, but Darrell found a way of doing it himself.
Read the complete tip →From the archive · Full text
Reader shop tip
Donald L. Olson, Saco, Mont.
“The power steering on my 706 International tractor quit working. I thought it was the hydraulic pump, which would have cost $490 to replace. But I found out there are not one but two filters in the hydraulic…
Read the complete tip →From the archive · Full text
Reader shop tip
George H. Hall, Jr., Somerset, Ky.
George built a “poor man’s” wick wiper out of a cattle oiler rope and a few other odds and ends.
Read the complete tip →From the archive · Full text
Reader shop tip
John Adams, Cross Plains, Texas
He had trouble with dirt and dust getting into the couplings for his air compressor-powered impact wrenches, paint guns and other tools.
Read the complete tip →From the archive · Full text
Reader shop tip
John W. Morgan, Colfax, Wash.
“I’ve never talked to anyone who wasn’t given fits by the ‘Brake Boosters’ on some early 1970’s IHC trucks like the 1973 1310 1-ton service truck I bought used five or six years ago. The ‘booster’ was apparently…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Kevin McWilliams, Columbia, N.J.
“We changed out Deere 3020 over to 12-volt electric from 24-volt and used a Delco alternator to replace the original generator system, which never charged enough to keep the batteries fresh.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Kevin McWilliams, Columbia, N.J.
“I made cheap TIG (heli-arc) wire for cast iron by sanding the old coating off some stickwire ni-rod. It had become wet and the coating was chipping off. It made perfect TIG wire, which I would otherwise have…
Read the complete tip →From the archive · Full text
Reader shop tip
Kirk Dahl, Ruby Valley, Nev.
“I scratch the date, engine hours and oil weight on each oil filter that I replace when changing oil. At a glance I know when to change oil again.”
Read the complete tip →From the archive · Full text
Reader shop tip
L.A. Daily, Norman, Okla.
“I had a lot of trouble starting my Deere 4010 propane burner in real cold weather. To solve the problem, I bought a pair of electric heating pads at the drug store and fastened them under the oil…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Linden Hankins, Bonanza, Ore.
“Freeman bale chamber slide bars have a tendency to get hay and dust behind them, making the plunger hard to adjust. When replacing the slide bars, I put a bead of silicone gasket adhesive behind them and along…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Linden Hankins, Bonanza, Ore.
“Freeman baler knives also have a tendency to wear at the bottom while the rest of the knife remains sharp. I fill the groove worn in the knife by the guide with hardfacing and grind it flat. They…
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Bint, Cysco, Tex.
“When a bolt head breaks off, I weld a flat washer to the bolt using a mig welder. Then I weld a large nut to the washer, let it cool, and 90 percent of the time I can…
Read the complete tip →From the archive · Full text
Reader shop tip
Mel Naggatz, Holyoke, Colo.
“I came up with a simple way to carry an emergency supply of air to the field. I made up a 8-ft. length of air hose with valve fittings on each end. If an implement tire gets low…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Paul Rusch, Nekoosa, Wis.
“I save money on bearings by purchasing them at one of two local bearing distributors for at least half the dealer price.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Paul Rusch, Nekoosa, Wis.
One tip on working with bearings: Heat expands and cold shrinks. Put a bearing in an oven at 200° to slide it on a shaft. Put it in the freezer to drop it into a bore.”
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Slattery, Rudolph, Wis.
“When I bought a tractor with a cab on it, I could no longer reach the manual controls on my Deere 3940 chopper. To solve the problem, I mounted a small orbit motor on the shaft that turns…
Read the complete tip →From the archive · Full text
Reader shop tip
Roland Holder, Hinton, Iowa
“I keep a few old wood splitting wedges on my welding bench to hold uneven pieces as I weld them together. They’re heavy enough to hold the parts in place and you can set up many angles. They’ll…
Read the complete tip →From the archive · Full text
Reader shop tip
S. Reppert, Reading, Mich.
“I take a round chain saw file and cut a notch on a pencil. Then I take half of a clothespin, with the spring in place, and I slip it down to the notch. This gives you a…
Read the complete tip →