Ronald Lankford
“I had to replace the roller height adjuster on my 84-in. Mott 3-pt. flail mower. I had steel pipe cut to length, made end caps, and used Cat III hitch pins welded to the caps for spindles. It…
Read the complete tip →5957 shop tips and stories · page 30 of 100, newest issues first.
“I had to replace the roller height adjuster on my 84-in. Mott 3-pt. flail mower. I had steel pipe cut to length, made end caps, and used Cat III hitch pins welded to the caps for spindles. It…
Read the complete tip →“The steering bearing on my Ford 3600 tractor broke inside the steering gearbox. It was originally oil-filled but the oil goes bad and then the bearing is not lubricated. I fixed the problem by fitting the gearbox with…
Read the complete tip →“The fan belt on that 3600 tractor was always loose. I solved the problem by placing 3 small washers under the AC compressor to raise the compressor slightly, keeping the belt tight. Worked great.”
Read the complete tip →Get faster response from gas and diesel engines with a Throttle Sensitivity Booster (TSB) from BD Diesel Performance. Step on the fuel pedal in most modern vehicles, and you’re stepping on an electronic sensor, not a mechanical linkage.…
Read the complete story →“Our new overhead sliding drawer uses the wasted space directly beneath your pickup topper to organize and secure tools and other equipment. It’s really handy to use,” says Mitch Johnson, Radco, Fargo, N. Dak. The Leer Locker consists…
Read the complete story →MTZ Ltd., the North American distributor of Belarus Tractors, says owners should beware of fake parts at a low price sold by scam distributors in the U.S. and Canada. Some are even identified with a Belarus metal stamp…
Read the complete story →Lee Egleston keeps his Dixon zero-turn riding mower in great working condition, thanks to his 2-wheeled dolly service lift.
Read the complete story →“I bought a 7-ft. wide, 3-pt. mounted Deere snowblower about 3 years ago. Upon receiving it I realized the snowblower was too heavy to move by myself, so I built a dolly for it,” says Douglas Fisk of…
Read the complete story →James Ryant could barely walk after a day in his new Deere 5525 90-hp. utility tractor. The problem was the seat.
Read the complete story →You can easily and safely drill holes into ceilings or trusses while standing on the floor with this new KwikPole invented by Reed Felton.
Read the complete story →Stick-on-labels make finding tools and parts easy. Marie Golden started the company, Steel Labels, to make labels for keys, but her husband Bob suggested labels for sockets and toolboxes.
Read the complete story →Marion Shaner, Lebo, Kansas, recently sent FARM SHOW photos of an overhead shop hoist he built with a non-bearing floor load. The hoist is free to move back and forth on a 24-ft. long I-beam that’s supported at…
Read the complete story →“I grew up on a farm and enjoyed working on tractors from age 12 on, so you might say I’ve been working at it for 40 years,” says Jeff Weller, who owns and operates Elite Restorations in Pennsylvania.
Read the complete story →“I made a counterweight to mount on the back of my tractor by filling a plastic barrel with concrete and equipping it with brackets to fit to the 3-pt. hitch.”
Read the complete tip →“You can recycle old barbed wire by using it as a replacement for rebar when pouring concrete for medium-duty jobs. You can use a lot of it and it’s easy to bend into curves and shapes around obstacles…
Read the complete tip →“I would like to share my experience with other readers that own an 8N Ford tractor with a 6-volt system. I recently installed electronic ignition that eliminates the points and condenser. It’s now a much better-running tractor. I…
Read the complete tip →“I use bicycle wheels to make carousels to hang parts. For example, I have one that holds battery cables and others that hold tools and horse tack. Just mount them horizontally on a spindle and they spin easily.”
Read the complete tip →“My son Terry had to get a big sprocket off a Harvestore silo unloader that was more than 40 years old. There was no way to get above it with a pry bar so he drilled two 3/8-in.…
Read the complete tip →“I avoid buying expensive hydraulic oil for my Bobcat when changing upper filters by pouring the oil into clean plastic buckets before removing filters, and then replacing the same fluid after.”
Read the complete tip →“I paint my log chain hooks with fluorescent marking paint to make them more visible in dim light or tall grass. Most people have had the experience of a chain falling off the platform of a tractor and…
Read the complete tip →“I use old plastic garden hose reels to hold heavy-duty extension cords. Makes them much easier to handle.”
Read the complete tip →“It isn’t often that I doubt something I read in FARM SHOW but that was the case with an article in an older issue about removing rust with water (Vol. 33, No. 4). It said to place a…
Read the complete tip →“I bought an old Ford pickup equipped with a 360 cu. in. engine that wouldn’t turn over. The hood was off so the engine had been exposed to the elements for several years.
Read the complete tip →“I got tired of aerosol paint cans, WD-40, and other cans rolling around on my shop floor, work bench, drill press, etc. So I found an old plastic Coke bottle carrier and mounted it on one side of…
Read the complete tip →“Do the wood beds on your trailers split and warp? Just brush on 2 or 3 coats of used motor oil with a 6-in. brush or roller. It’ll soak in and preserve the wood.”
Read the complete tip →“I read an idea in FARM SHOW about using tire stems as vents on new-fangled gas cans without vents. Great idea! So I installed them in several of my ‘worthless’ new gas cans. Unfortunately, after about 6 months…
Read the complete tip →“The Handle Clamp ($37.50) bolts to any flat surface and is designed to hold tools such as a broom, shovel, grease gun, rake, ax, etc.
Read the complete tip →“Here’s a tip to make vice grips easier to use. Replace the adjusting screw with an eye bolt. Makes it a lot easier to turn for adjusting and you can put a rope or tool through the eye…
Read the complete tip →“Here’s an idea I use to shorten a chain or take the slack out of a chain when pulling. Just attach two clevis grab hooks together. Hook one of the grab hooks to the chain and pull up…
Read the complete tip →“Rainwater runs down into the exhaust manifold through the stack on my old Farmall Super C. I solved the problem by simply putting an empty dog food can over the top of it when we park it. The…
Read the complete tip →“A simple Nerf foam football works great to keep debris out of the exhaust stack on tractors and other self-propelled machines while transporting them. It also keeps turbochargers from turning and burning up bearings,” says Gary Nix, Mountain…
Read the complete story →“I didn’t like the 4-ft. fluorescent light fixtures in my shop. They burn out too often and make a humming noise. I finally decided to replace all the fluorescent lights with modified compact fluorescent lights (CFL’s).
Read the complete tip →“I own 3 different size chainsaws and need 2 different kinds of files to keep the chains sharp. To save money I buy a dozen Oregon round files at a time. The files come packaged in a cardboard…
Read the complete tip →“Old, dead batteries can sometimes be revived by putting a couple drops of Motorkote engine lubricant in each cell and then slow charging the battery overnight. The lubricant washes the acid off the lead plates in the battery…
Read the complete tip →“The charger went bad on my Alemite 14.4-volt battery-powered grease gun due to a bad transformer. A replacement charger from the company would have cost about $150. Instead, I replaced the bad transformer with a 16-volt doorbell transformer…
Read the complete tip →Their new gearshift plate kit is designed to fit all Case IH Magnum tractors. For 2-reverse gear tractors, the kit expands your reverse gears by making the third and fourth gears operational – thus making your 2-reverse tractor…
Read the complete tip →“Many times when I’m away from my shop I’ve wished I had a vise to use on some job. So, I came up with this vise-mounting bracket that works with any standard 2-in. receiver hitch,” says Connor Bishop,…
Read the complete story →Steve Brubaker got tired of stumbling over air hoses and electric cords in his 50 by 80-ft. shop, so he used car parts to make a ceiling-mounted, 12-ft. long boom to hold them. It swings in an almost…
Read the complete story →Howard Reischauer was going to tear down an old corn crib to make room for a new farm shop.
Read the complete story →If your diesel fuel sits very long in the tank, test it before you use it, suggests John Nightingale, Dieselcraft Fluid Engineering. Over time, diesel fuel without stabilizers can oxidize.
Read the complete story →“We can fine-tune a gas or diesel engine to produce more power, drive better, shift better and use less fuel doing it,” says Ford performance specialist Doug Lewis.
Read the complete story →Tom Kalista, Longview, Wash., converted a burned-out barbeque grill into a handy, wheeled tool cart.
Read the complete story →Daytona Parts Company prides itself on having everything you need when it comes to carburetors from present day to as far back as 1925. The company website offers more than 100,000 records of carburetors, kits, and parts, both…
Read the complete story →If you need a radiator, the Radiator Supply House either has it on hand or can get it. They have more than 10,000 radiators, oil coolers, charge air coolers, A/C condensers and shrouds for cars, trucks and more.…
Read the complete story →“When I started a steel fabrication business, I needed a metal brake to bend metal. I already had a 20-ton shop press, so I decided to build a metal brake for it, too,” says Kevin Ranette, Moyie Springs,…
Read the complete story →“My patent pending battery disconnect is designed to extend the life of batteries and other components when equipment is idle for an extended period of time.
Read the complete tip →“As a former IH serviceman, I always kept a small magnet in my tool kit to attach to a wrench to hold tiny screws, bolts, washers or nuts when replacing parts. It’s a very handy way to keep…
Read the complete tip →“I worked on a large farm for a year and a half and one of my biggest projects was setting up a service truck. The owner liked cordless power tools so there were a lot of batteries to…
Read the complete tip →“To keep ratchet straps and bungie cords from getting tangled up when they’re not being used, I store them in old socks. For example, I might fold a half dozen bungie cords in half and stuff them in…
Read the complete tip →“For years farmers with Freightliner semi tractors told me they needed fuel tank straps that wouldn’t rust out. We’re excited to announce that we now have replacement straps at an affordable price.
Read the complete tip →“For 30 years I’ve used a golf ball to squeeze every last bit of material out of caulking tubes. Once you’ve used part of a tube, pull back the handle on the caulking gun and put a ball…
Read the complete tip →“When the engine shroud on my old Simplicity garden tractor cut some wires that caused the generator to burn up, I decided it would be cheaper and easier to replace it with a 1-wire auto alternator. The Briggs…
Read the complete tip →“I wanted to make holes in wine bottles to insert Christmas lights. So I bought a carbide drill but it tended to ‘wander’ and chip the hard glass.
Read the complete tip →“When repainting a house, barn or other building, I often come across isolated small areas where the wood is rotted, especially on window frames. There are commercial hardeners but they’re usually so watery that most of the hardener…
Read the complete tip →“In the last issue of FARM SHOW, a reader wondered if anyone had a solution to drill bit slippage in cordless drills. As a retailer of Norseman/CTD cutting tools, I suggest he try our Magnum Bully line of…
Read the complete tip →“My homemade fuel injector tester works great for trouble shooting injector problems on diesel engines,” says Paul Bernier, Geyserville, Calif. He made a tester out of a hydraulic jack from a cab-over truck.
Read the complete story →“Some of the grease zerks on my farm equipment are located in tight corners where I need a hose on the grease gun, and some are in narrow corners too small to reach with my hand and therefore…
Read the complete tip →“I use the metal cages around plastic bulk chemical totes to store metal tubing, pieces of pipe, conduit, and other parts. I flip the metal cages upside down. By inserting crossbars I’m able to stack items too short…
Read the complete tip →“By triple rinsing the plastic totes and then hooking up a trickle hose, they work great to water plants and trees.”
Read the complete tip →“My dad and I made a super bright workbench light on the cheap. We bought 2 Snap-On LED work lights for $33, took the mount off the bottom of each light, and mounted them on the ceiling above…
Read the complete tip →