From the archive · Full text
Feature story
Featured source:
“Our new line of engine and manifold paints are rated to withstand up to 1,800 degrees F., which far exceeds the heat range of anything else on the market,” says Bill Hirsch Automotive, Newark, N.J.
Read the complete story →From the archive · Full text
Feature story
Featured source:
After our story in the last issue on Por-15, a popular paint-on rust eliminator that reacts chemically with rust to turn it into a rock-hard, epoxy-like finish (call 800 576-5822 for info), we heard from a FARM SHOW…
Read the complete story →From the archive · Full text
Feature story
Featured source:
You can safely refill small propane cylinders - which most people just throw away when they’re empty - with this new refill device for propane tanks.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source:
You can do a better job welding sheet metal with these “panel clamps”, according to the manufacturer who says they make butt welds easier by holding loose edges tightly together.
Read the complete story →From the archive · Full text
Reader shop tip
Allan S. Maclean, Kingston, Ont.
“Waste oil can be stored in horizontally mounted 45 gal. drums by installing a piece of 2-in. pipe formed into a 90° elbow. Screw one end into the 2-in. hole, swinging it up to fill and down for…
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky.
“To break the bead of stubborn tires from the wheel rim, I lay a 3 by 4-in. board on the tire with the end close to the wheel rim and drive one wheel of a vehicle up on…
Read the complete tip →From the archive · Full text
Reader shop tip
Lloyd Meffert, Hettick, Ill.
“I don’t have as many broken blade bolts since I bolted a pair of metal skids onto both sides of my 5-ft. wide New Idea mower. I use the mower to clear pasture land on which I’ve already…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Pete Peters, Osler, Sask.
“Here are a couple of back-saving ideas I use. First, I made a heavy-duty cart from the front axle and wheels off an old riding mower. It works great for moving auger engines and other heavy items without…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Pete Peters, Osler, Sask.
Second is a convenient stand to hold an empty water tank that I use in the back of my pickup truck. The stand, made of treated posts and lumber, is the same height as my pickup bed. All…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Pete Peters, Osler, Sask.
Peters also passed along an electrical idea.“If you need to replace the alternator on an older tractor, combine, or other vehicle, its simple to make the changeover from the old external regulator style to the newer internal regulator…
Read the complete tip →From the archive · Full text
Reader shop tip
Richard Cox, Jacksonville, Ill.
“I bought a pair of vises at an auction, which I turned into a large jig to hold items that I want to weld. For example, I can weld two rods together end to end. Having a firm…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Robert Dunton, Topeka, Ill.
“The first thing I did when I bought my new 3-pt.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Robert Dunton, Topeka, Ill.
“I also replaced the metal guards on both sides of the back part of the deck with lengths of flexible 1/2-in. thick rubber. The original metal guards would at times drag in the ground and tear it up,…
Read the complete tip →From the archive · Full text
Reader shop tip
William Winter, Tower Hill, Ill.
“I bought a scissors table at a factory dispersal sale and put wheels on it so I can move it around the shop. I use it to move supplies and materials around. I can load them from the…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Robert Dunton, Topeka, Ill., found an easy way to boost heat output of the wood stove he uses to heat his shop.
Read the complete story →From the archive · Full text
Reader shop tip
Denis Seewald, Mustang, Okla.
“The bearings were worn out in my late ’40s or early ’50s vintage John Deere 8 ft. tandem disk. When I took it apart, I found there was dirt in the bearings and that had worn out the…
Read the complete tip →From the archive · Full text
Reader shop tip
Gene Snellings, Montreal, Mo.
“I made my own shop on wheels, starting with the frame of an old pickup to which I added a tongue made of steel box tubing. I used two sheets of 9-gauge steel to make a 7 by…
Read the complete tip →From the archive · Full text
Reader shop tip
Marvin Kellen, Rt. 2, Box 155, Madison, Minn. 56256 (ph 320 598-3279)
“When the return hydraulic line under the platform on my Deere 520 tractor rusted out, I discovered that Deere no longer makes the part and no one else does, either. So I had a local machine shop fabricate…
Read the complete tip →From the archive · Full text
Reader shop tip
Michael Vanhorn, Sentinel Butte, N. Dak.
“When the U-joints on our 1983 Ford F-250 4-WD pickup went out, we made a tool that lets us remove the U-joints without having to take the driveshaft out. We just slide the tool in there, take the…
Read the complete tip →From the archive · Full text
Reader shop tip
Richard B. Allen, Queens Leo, Nova Scotia
“During the past three years I’ve had difficulty being able to see the twine when baling with my New Holland 630 baler. I couldn’t tell if the twine was moving or not so I often dumped out bales…
Read the complete tip →From the archive · Full text
Reader shop tip
Richard Cox, Jacksonville, Ill.
“Grinding jobs are a lot cleaner ever since I installed a vacuum system to carry dust and small grindings out through my shop wall. I used a small fan and furnace pipe with elbows to do the job.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Robert T. Valentine, 417 Commercial Ave. S., Wolsey, S. Dak.
“I read about the problems Norman Fiddler has had with front spindles breaking on his Deere 4020 tractor (Vol. 25, No. 5). I had the same problems with my Deere 4010 but I solved it in a different…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Robert T. Valentine, 417 Commercial Ave. S., Wolsey, S. Dak.
“I solved another problem with a broken spindle on our Oliver 1650 tractor. The 1650 uses the same spindle found on an Oliver 88 tractor. I removed the spindles complete with the outside housing and also the wheel…
Read the complete tip →From the archive · Full text
Reader shop tip
“I came up with an attachment for small lathes that’s designed to cut round shapes or curves into brass, aluminum, steel, or plastic. The tool cuts convex curves up to 3/4 in. in diameter. Works great for making…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Spiering, Milbank, S. Dak.
“I converted an old step-in electric fence post into a low-cost, drill-operated paint mixer which I use to stir up 1-gal. pails of paint. I used a chop saw to cut the post off flush with the top…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Spiering, Milbank, S. Dak.
“I used a length of 2-in. dia. PVC tubing to make a vacuum nozzle that hooks up to my shop vac. It works great for cleaning out leftover seed in my drill fill auger. I used an electric…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source:
Shop towels and chamois will last longer if you use this hand-operated wringer to wash them, says Fast Lane Products, Palos Verdes Peninsula, Calif.
Read the complete story →From the archive · Full text
Feature story
Featured source:
The switch from blowing off combines to sucking chaff out of engine components is easy with this new nozzle that acts as both a blower and a vacuum.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Arco Rosenow of Chillicothe, Ill., recently contacted FARM SHOW about a unique product that he discovered and liked so much he started selling it.
Read the complete story →From the archive · Full text
Feature story
Featured source:
There are a number of rustproofing products on the market, but the one that most do-it-yourselfers seem to be using is POR-15, a “paint-over” product that stops rust in its tracks.
Read the complete story →From the archive · Full text
Feature story
Featured source:
While covering the Farm Science Review near Columbus, Ohio, we came across an unusual exhibit set up by a local tire company.
Read the complete story →From the archive · Full text
Feature story
By By Mick Lane, Contributing Editor
Featured source:
If you’ve stashed an antique or collectible tractor or two in the shed for years and still haven’t gotten around to starting the planned restoration, you might want to consider turning the job over to a professional.
Read the complete story →From the archive · Full text
Reader shop tip
Alfred Wilson, Annville, Ky.
“I read a blurb in a recent issue about a guy who re-moved a broken stud by welding a nut to it. I had a similar experience that I solved a different way. My car had a broken…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Don Lasee, Don’s Welding & Repair, 2486 Hwy. 32, Krakow, Wis. 54137 ph 920 899-3690
“To remove an outer bearing race from a blind hole, simply weld a bead inside the race where the balls ride, wait 30 seconds, and it will come free.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Don Lasee, Don’s Welding & Repair, 2486 Hwy. 32, Krakow, Wis. 54137 ph 920 899-3690
“Several lengths of 3/8-in. rerod, driven into holes drilled in mortar joints in a block wall, make quick shelf supports. Drill under the web of the block above.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Don Lasee, Don’s Welding & Repair, 2486 Hwy. 32, Krakow, Wis. 54137 ph 920 899-3690
“I use a product called Sportsman Goop to repair the rubber steering wheel on an old tractor. After years of exposure to the sun, the rubber had dried out and cracked. Big pieces of rubber fell off, making…
Read the complete tip →From the archive · Full text
Reader shop tip
“I came up with a nifty tool-mounting system that makes it easy to move bench-mounted tools around the shop and also take them around the farm. This includes my drill press, chop saw, pipe vice, and regular shop…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Glen Gettemeyer, Saint Peters, Mo.
“I spray WD-40 on dirty grease fittings that are hard to work. Lots of times it helps. I often spray it on the night before and grease in the morning.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Glen Gettemeyer, Saint Peters, Mo.
“One simple idea I use in my shop is keeping a 1-gal. can sitting on the workbench. I put screwdrivers in the can and hang pliers on the sides with one handle in and one out. Makes the…
Read the complete tip →From the archive · Full text
Reader shop tip
John Adams, Cross Plains, Tex.
“If you lose the grease retainer cap on the end of an axle, you can replace it with a beer can cut in half. Just shove it onto the end of the axle and it will stay on.”
Read the complete tip →From the archive · Full text
Reader shop tip
Lyle Bruns, Ly-Mar Mfg., Tower Hill, Ill. 62571 (ph 217 567-3675)
Lyle came up with a method of cutting perfectly round holes in box steel or flat plate. He made an attachment for his cutting torch that has a pin under it to center in the proposed hole. Distance…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Pete Peters, Osler, Sask.
“I made a ramp for servicing garden tractors out of 4 by 4 treated posts set into the ground. I fastened old rubber belting onto the ramps for better traction. This permanent installation makes it easy to make…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Pete Peters, Osler, Sask.
“Another idea I had was making a fence tool caddy out of old elevator leg buckets bolted together back to back. The buckets were bolted to each side of a piece of 3/8-in. plywood with a hole cut…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Dunton, Topeka, Ill.
Two large hinged doors separate the shop from the storage section of Robert’s machine shed. He uses the large doors for storage, hanging ladders, brooms, and other items on hooks.
Read the complete tip →From the archive · Full text
Reader shop tip
Stan McDonald, Foxboro, Ont.
“Like other FARM SHOW readers, I like to build the things I need. That often means cutting flat bars, channel iron, and so on. So I bought a powered bandsaw. The problem I ran into is that the…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
New Power Caulker adapts to virtually any electric drill, eliminating the need for an air compressor or bulky, heavy air lines.
Read the complete story →From the archive · Full text
Reader shop tip
Bruce’s Welding, 302 A 3 rd , Girard, Ill. 62640 ph 217 627-2241
An Asian timber known as Apitong has become a favorite building material at Bruce’s Welding whenever there’s a call for extremely tough wood that will be slow to rot. Apitong was used for the deck of this trailer…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Kopriva, Raymond, S. Dak.
“Those little scissors jacks that come in small cars work slick with an air impact wrench. They jack up light implements in a jiffy or spread bent iron better than expensive hydraulic jacks.”
Read the complete tip →From the archive · Full text
Reader shop tip
Vic Stratman, Argyle, Mo.
“The tie rod ends on my Deere 2440 tractor are built in Continued from previous page three sections. The outside section slides into a sleeve and clamps on. When they get worn, they’re very hard to get out.…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“I got behind with my mowing so a friend of mine, Tommy Floyd, came over to help me get caught up. Tommy’s mower had a good sized hole in the back of the deck, where it had rusted…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“A friend asked me to do some DC welding on rather thin steel. He thought I could arc weld the material. I knew I could do it but I wanted to do the neatest job possible so I…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source:
Hate cleaning up after drilling holes to install wall anchors or ceiling fixtures?
Read the complete story →From the archive · Full text
Reader shop tip
Denis Seewald, Mustang, Okla.
“I’ve come up with a cheap way to hang tools in my shop. I hang a 4 by 8-ft. sheet of plywood on the wall, then drill holes as desired and glue in 5/16 or 3/8-in. dowel rods…
Read the complete tip →From the archive · Printed page image
Reader shop tip
Gaston Homoline, Domremy, Sask.
Text from the original printed page; see page image.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Jody Lagerquist, Westby, Mont.
“You can use a standard garden hose reel to hold air hose. Attach the hose to an air supply pipe on the wall, using a quick coupler. The quick coupler serves as the swivel.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jody Lagerquist, Westby, Mont.
“While knocking off the flyweight on a Case-IH 8380 haybine’s sickle drive, I almost broke the puller. I had trouble putting it back on, too. I applied a product called Never-Cease to the shaft and flyweight and it…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Tom Carey, Jr., Boulder, Mont.
“I’ve found that I can replace 6 and 12-volt generator-equipped engines with 12-volt alternators. Some minor modifications to the ignition on 6-volt systems are necessary, but everything else is simple.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Tom Carey, Jr., Boulder, Mont.
“I built a drive-over pit in my shop for changing oil, greasing, and doing other service work under equipment. I built steps down into it and I have a cover when not in use. This makes routine chores…
Read the complete tip →