From the archive · Full text
Reader shop tip
Paula Vogelgesang, Pennywise, Box 518, Kadoka, S. Dak. 57543; email
penny [email protected]: Here’s a way to clean grease or oil stains off concrete garage floors or driveways using two common materials – paint thinner and cat litter. It comes from Paula’s monthly newsletter, “Pennywise”.
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Rust and corrosion on tire rims, valves, gauges, and pumps can now be prevented, thanks to a new patented, non-toxic, biodegradable product called Rim Guard Tire Ballast.
Read the complete story →From the archive · Full text
Reader shop tip
Arthur H. Harms, Estelline, S. Dak.
“I have two vehicles that both ran hot during the summer - a 1976 Dodge pickup and a 1981 Mercury car equipped with a 302 cu. in. engine. I made two modifications to solve the problem. First, I…
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Hudspeth, Era, Texas
He recently sent FARM SHOW photos of a couple of slick add-ons he made for his extension ladder.
Read the complete tip →From the archive · Full text
Reader shop tip
Chris Elliott, 4404 Breezy Point Road, McConnellsburg, Penn. 17233
“The rubber on the rolls on our Deere 1460 disc mower was coming off, which caused the machine to plug up. After pricing new rolls, we decided to fix the problem on our own. We stripped the rest…
Read the complete tip →From the archive · Full text
Reader shop tip
David Rowlett, 1209 S. Ash St., Ozark, Ark. 72949
“By inserting a small round magnet into the end of a rubber line, you can retrieve a nut or bolt from just about anywhere, such as down an engine intake manifold.”
Read the complete tip →From the archive · Full text
Reader shop tip
Donald J. Woehl, 8740 Kenton Road, Morrison, Ill. 61270 ph 815 772-3765
“I’d like to thank FARM SHOW and its readers for helping me with a problem I had with my Deere 720 2-cyl. tractor, which I had changed over to electronic ignition. The problem was that the coil was…
Read the complete tip →From the archive · Full text
Reader shop tip
Donald Struckhoff, Augusta, Mo.
“The self-energized disc brakes on Farmall Super C to International 660 models tend to lock up after wet weather or whenever they’re not in use for a while. To solve the problem I put several squirts of gas…
Read the complete tip →From the archive · Full text
Reader shop tip
Donald Struckhoff, 5266 Hackmann Rd., Augusta, Mo. 63332 ph 636 228-4396
“The self-energized disc brakes on Farmall Super C to International 660 tractors tend to lock up after wet weather or if they haven’t been used for a while. Rust can form on the metal surface. I’ve found that…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 5
Individual tip 1 of 5 from this reader’s published contribution.
Lonnie J. Wallace, Jerico Springs, Mo.
“To stop an engine from fouling up plugs, I hooked up two coils together. This set-up re-ally sends a jolt of current to the plugs. The plug fouling slowed way down.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 5
Individual tip 2 of 5 from this reader’s published contribution.
Lonnie J. Wallace, Jerico Springs, Mo.
“When cleaning cast iron carburetors, I mix a can of lye and a half cup of soap in a plastic bucket filled with two gallons of hot water. This idea also works in a cruddy fuel tank.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 5
Individual tip 3 of 5 from this reader’s published contribution.
Lonnie J. Wallace, Jerico Springs, Mo.
“I installed a 10-ton floor jack instead of a 4-ton model. I don’t have to worry about overloading such a heavy duty jack.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 5
Individual tip 4 of 5 from this reader’s published contribution.
Lonnie J. Wallace, Jerico Springs, Mo.
“I’ve found that General Electric soft white 60-watt light bulbs make the best rough service bulbs. They’re fluorescent so they don’t get hot.
Read the complete tip →From the archive · Full text
Reader shop tip 5 of 5
Individual tip 5 of 5 from this reader’s published contribution.
Lonnie J. Wallace, Jerico Springs, Mo.
“I drill a small hole in all bearing seals and fill them full of grease. Then I clean the holes with brake cleaning fluid and seal them up with silicone sealer. The bearings then last like they should.…
Read the complete tip →From the archive · Full text
Reader shop tip
Michael Pigorsh, Northco Products LLC, P.O. Box 1093, Big Rapids, Mich. 49307 (ph 231 527-1660; fax 231 527-1665; email
[email protected]; website: www.rustreaper.com): “We think our new
Read the complete tip →From the archive · Full text
Reader shop tip
Pete M. Friesen, Meade, Kansas
“I had a problem with the anhydrous ammonia hitch on my V-blade tillage implement. It was hard to reach to pull the spring-loaded pin and, with the other arm, pull the hitch back at the same time. So…
Read the complete tip →From the archive · Full text
Reader shop tip
Richard Bergman, Chippewa Falls, Wis.
“I bought a 4-ft. pull-type rotary brush mower in the early 1960’s. I didn’t have an over-running clutch for the pto, so once the mower got up to speed it drove the rear wheels as long as the…
Read the complete tip →From the archive · Full text
Reader shop tip
Rusty Olson, 2255 280 th St., Garner, Iowa 50438 ph 515 291-2082; email
[email protected]: “Don’t throw out your electrode (stick) welder. Some day you’ll be glad you still have it. Around our shop most things are built with ‘recycled steel,’ and while we do have a nice mig welder we’ve found…
Read the complete tip →From the archive · Full text
Reader shop tip
Trevor Shute, RR 6, Guelph, Ontario, Canada N1H 6J3 (ph 519 822-6705)
“Here’s a tip to prevent scalping or ripping out chunks of lawn when plowing snow. I removed the skid plate from the bottom of my 7-ft. scraper blade and replaced it with a section that I cut from…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source:
Getting mitered corners to fit tightly together is a piece of cake with these new meter clamps that keep the pressure on while glue dries, says Collins Tool Co., Plain City, Ohio.
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you own an older Deere 2-cylinder tractor equipped with a single barrel carburetor, you’ll be interested in this carburetor repair kit from Marvin Henry, Maywood, Neb.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Here’s an idea we recently spotted in Four Wheeler Magazine (www.fourwheeler.com).
Read the complete story →From the archive · Full text
Feature story
Featured source:
By cutting down an old 1,000-gal. propane tank, Lonnie Nichols, Copeland, Kansas, was able to build a portable “oil vac” that he uses to remove used oil from irrigation engines. A second tank on the trailer carries fresh…
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you own an older Ford pickup with a rusted-out tailgate, you’ll be interested in this replacement tailgate that looks just like the original. It’s available from an Oklahoma company that specializes in classic pickup bed parts for…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Not many people build their own brake presses to bend sheet metal, but Wilfred Mollenbeck made a giant one with a 20-ft. wide bed. It measures 15 ft. high and weighs about 18,000 lbs. A hydraulic power pack…
Read the complete story →From the archive · Full text
Feature story
Featured source:
This new hydraulic-operated bench vise is as simple to use as stepping on a pedal. And, it doubles as a hydraulic press.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“If I was putting up a new building, I’d build it this way. It gives me more room to work and also lets in a lot of light,” says Mark Bruellman, Rolfe, Iowa, who raised a section of…
Read the complete story →From the archive · Full text
Feature story
Featured source:
A Minnesota farmer has come up with a simple fix for a common problem on newer-style, Case IH 2200 series corn headers.
Read the complete story →From the archive · Full text
Reader shop tip
Charles Gerdeman, Delphos, Ohio
“After buying a used Deere semi-mounted sickle mower, I discovered that all the universals at the gearbox end were made wrong. To solve the problem, I used a torch to heat up the joints and bent them at…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Eric Webster, Lansdowne, Ontario
“I made the frame of this hydraulic press out of old bulldozer parts. It runs off tractor hydraulics and has a ‘bed’ made out of a 6-in. wide, 3/4-in thick steel plate. The 6-in. dia. hydrau- lic cylinder…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Eric Webster, Lansdowne, Ontario
“I made this tire band saw out of two spare car tires. An electric motor belt-drives a pair of pulleys that turn a shaft that rotates the bottom tire. The saw blade runs from one tire to the…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Eric Webster, Lansdowne, Ontario
“My homemade 48-in. belt sander is operated by a 1 hp electric motor. I use it to make furniture. The belt is 6 in. wide. A pair of screws at each end of the unit are used to…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Floyd VerPloeg, Lavilia, Iowa
“I take magnets out of old microwaves for use around the shop. There are two strong magnets in every microwave. Be sure to short circuit the capacitor before working on it because it can still store high voltage.…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Floyd VerPloeg, Lavilia, Iowa
“I use the magnets to pick up spilled nuts, bolts, nails and other parts. I just put the magnet in a plastic bag, pick up the spilled parts, and then turn the plastic bag inside out and the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
James Weaver, Weaver’s Repair, 9507 Forest Ridge Rd., Shippensburg, Penn. 17257 (ph 717 477-9332)
Weaver’s Repair specializes in new and used parts for compact utility-sized tractors. He recently started selling brand new aftermarket cylinder heads for Kubota V1902 and V1702 engines.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
James Weaver, Weaver’s Repair, 9507 Forest Ridge Rd., Shippensburg, Penn. 17257 (ph 717 477-9332)
Weaver has another new product that he thinks is a real winner.
Read the complete tip →From the archive · Full text
Reader shop tip
John Lindemer, Ind.
Several years ago, a neighbor of John’s had problems with frozen pipes. The problem was compounded by the fact that the frozen pipes were made of pvc instead of copper so he couldn’t use his welder to thaw…
Read the complete tip →From the archive · Full text
Reader shop tip
John Martens, Sanford, Man.
“I made a portable air-tool oiler out of some angle-iron and an old steering wheel. The wheel can act as a base or a handle.
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Scharabok, Waverly, Tenn.
“I replaced the gauges on an old Ford backhoe with automobile gauges, saving the cost of expensive dealer replacements. I traced the pattern of the gauges on a piece of plexiglass and cut out the new holes. I…
Read the complete tip →From the archive · Full text
Reader shop tip
Lawson Products, Inc., 1666 E. Touhy Ave., Des Plaines, Ill. 60018 (ph 800 448- 8985; website
www.lawsonproducts.com): Lawson products has come up with a grinding disc that has three holes in it. When the disc is in motion the holes give you an accurate view of exactly what you are grinding. The company says…
Read the complete tip →From the archive · Full text
Reader shop tip
Pete Peters, Osler, Sask.
“I have come up with a stand that makes it easy to pour oil or other substances easily. It consists of an old wheel rim with a piece of steel pipe welded onto it. The strap iron bracket…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Dixon, Oxford, N.C.
“I bought a used Allis Chalmers 8030 4-WD tractor from the early 1980’s. We got it cheap because it was smoking quite a bit, although it seemed to run okay. I figured I could rebuild it and come…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
It took Jacob May only about an hour to make a set of portable car ramps, using nothing but his cutting torch, welder and a bit of scrap metal.
Read the complete story →From the archive · Full text
Reader shop tip
Craig Richlen, Lockhart, Tex.
“I have successfully used “JB Weld” to do body work on my wife’s minivan and various other equipment. It’s an epoxy that can be used to hold any porous or non-porous surface. When I have a stripped screw…
Read the complete tip →From the archive · Full text
Reader shop tip
Darryl Foreman, Lafayette, La.
“I mount a roll of paper towels on hangers that attach to the frame on the underside of the trunk lid on my Buick Century car. That way I always have a towel handy to clean off my…
Read the complete tip →From the archive · Full text
Reader shop tip
Floyd VerPloeg, Lovilia, Iowa
“In your last issue, a reader talked about greasing U-joints and tie rods until the grease comes out the seals. This is wrong on two counts. Number 1, grease does not wear out. Number 2, if you break…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
“We offer new and used parts for heavy equipment and diesel engines, both OEM and aftermarket. We carry filters and engine overhaul kits as well as new and used parts for excavators, shovels, loaders, dozers and more. We…
Read the complete tip →From the archive · Full text
Reader shop tip
Gene Pearson, Wichita, Kan.
“I bought two 24 by 20-in. stainless steel coolers from a local buffet restaurant. I put the coolers together and topped them with a 1/4-in. steel plate and they make some of the best workbenches I’ve seen.”
Read the complete tip →From the archive · Full text
Reader shop tip
Rogers Metal Works, Inc., 114 Caldwell St., P.O. Box 221, Auburn, Ky. 42206 ph 270 542-7135; fax 270 542-4035; email
[email protected]: “We manufacture aftermarket replacement fingers for stripper headers that are compatible with all stripper headers on the market. They sell for only about half the price of OEM replacement fingers, and lab and field tests over the…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Dan Jacobson, Pequot Lakes, Minn., doesn’t have a tailgate on back of his pickup. That’s because he often uses the pickup bed as a work table in the shop or field. One of his handiest tools is a…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I built a lawn mower service ramp. It’s made out of angle iron and has a hinge on one end to fold the legs up and lower the ramp. Once the mower is on you just lift the…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I built it to save my back,” says George “Bing” Ribble about an easy rotating shop hoist he uses to move heavy loads of a ton or more into and out of his shop.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Mark Richter, Endicott, Wash., contacted FARM SHOW recently to tell us about his new “sight gauge” caps for Case IH Quadtrac 4-WD tractors that ride on rubber tracks. The sight gauge cap consists of a small brass plug,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Like all Case 850 crawler tractors, mine was difficult to steer. I added a pair of steering levers that make it steer as easy as a Caterpillar,” says Robert Gibson, Canby, Oregon.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I came up with a way to charge older Deere diesel tractors for less than $100,” says Ken Armstrong, Point, Texas.
Read the complete story →From the archive · Full text
Feature story
Featured source:
When Glenn and Gordon Marshalek, Raymond, Nebraska, needed to pull the engine and transmission from a garbage truck, they realized their normal engine hoist might not be able to handle it.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Hydraulic hoses on equipment used to get pulled, dragged, or caught on my tractor tires, but my new Hose Holder eliminates those problems,” says Thom Koch, Petersburg, Ohio.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Our new tire sealant for ATV’s will seal up to a 1/2-in. puncture in the tread and 1/4-in. puncture in the sidewall,” says Glen Urguhart, Tucker Rocky Distributing, Ft. Worth, Texas.
Read the complete story →