Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Richard Batstone
Since more than a quarter million Farmall and International Cub tractors were built between the years 1947 and 1981, there’s a big market for parts. Ten years ago Richard Batstone tapped into that market with his website, www.farmallcubforever.com.…
Read the complete story →From the archive · Full text
Feature story
Featured source: Tom Haller
Tom Haller of Palmyra, Neb., recently responded to a story in our last issue on how a reader cleans greasy air filters on his Bobcat skid loader. The reader explained how he sprays a can of starter fluid…
Read the complete story →From the archive · Full text
Feature story
Featured source: Shane Myrick
“I can drive it around anywhere on my farm where I need air, or drive it onto a trailer and operate air tools away from home,” says Shane Myrick, Pleasanton, Kan., who converted an old riding mower into…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dennis Burkholder
“My dad was a fulltime farmer and part time mechanic, and since Deutz tractors were popular around here, he repaired quite a few of them. I gravitated into the repair business myself and eventually he and I built…
Read the complete story →From the archive · Full text
Feature story
Featured source: Matthias Wandel
Dull chainsaw chain? Worn files? No worries, says Matthias Wandel. Grab an angle grinder with a cutoff metal wheel. The Canadian blogger tried it when he needed to sharpen a chain. It worked so well he made a…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Darwin Gingerich
Darwin Gingerich grew up as a pastor’s son in a small Kansas community. At a young age his interests tended more toward Deere tractors than theology.
Read the complete story →From the archive · Full text
Feature story
Featured source: James Tuschner
You can get the answers to any questions you have about ag tires at the website, www.agtiretalk.com. The new website can make you a better buyer and user of today’s high tech tires.
Read the complete story →From the archive · Full text
Reader shop tip
Bill Halstead, Lacey, Mich. (269 758- 3232)
“I couldn’t justify spending money for new LED light fixtures in my shop, so I came up with a cheap way to install LED bulbs. I removed the ballast from my fluorescent lights and used the existing wiring…
Read the complete tip →From the archive · Full text
Reader shop tip
Bud Falkenstein, Mono, Ontario
“To add oil to mowers, rototillers, generators and other small engines, just pour the oil into a squeeze ketchup bottle. The oil won’t flow until you squeeze the bottle, which means no more oil spills.”
Read the complete tip →From the archive · Full text
Reader shop tip
Darrell Cooper, Chillicothe, Mo.
“Here’s an easy way to repair a rusted area on a grain bin - use foam insulation in a can to seal it. We’ve used this idea on bins that rusted down where the bin’s metal sides meet…
Read the complete tip →From the archive · Full text
Reader shop tip
David Nordhus, Seneca, Kansas
“I couldn’t add front weights on my tractor because the bolt hole in the mounting bracket was plugged with dirt, and I couldn’t screw the mounting bolt in tight. Using a screwdriver, I was able to clean some…
Read the complete tip →From the archive · Full text
Reader shop tip
Donald Jaster, Bruce, Wis.
“I needed an adjustable clevis that would let me adjust both brake pedals on my Allis Chalmers B tractor. I don’t have an Allis dealer close by for parts, so I bought an aluminum turnbuckle with an open…
Read the complete tip →From the archive · Full text
Reader shop tip
John Slater, Olin, Iowa
“I spray Fluid Film onto disc openers, shanks, and corn head gathering chains, etc. - anything metal that might rust during the off season. When
Read the complete tip →From the archive · Full text
Reader shop tip
John Torrance, Rocanville, Sask.
“This is in response to the reader who has a 2010 Deere 3005 4-WD compact utility tractor equipped with a Yanmar 3-cyl. diesel engine that keeps shutting down (Vol. 39, No. 6). Unfortunately, replacing the fuel filters or…
Read the complete tip →From the archive · Full text
Reader shop tip
John Youngdahl, Green Isle, Minn.
“My wife has a Toro Groundmaster mower with a 4-cyl. aluminum head. One day one of the spark plugs blew right out. After taking a look, I realized the last mechanic who worked on the tractor put short-reach…
Read the complete tip →From the archive · Full text
Reader shop tip
Kurt Hofmeister, Woodburn, Oregon
“Trying to assemble anything with loose washers often can be a frustrating experience. So if the washer is loose, I just roll a small O-ring onto the bolt and use it to hold the washer in place.”
Read the complete tip →From the archive · Full text
Reader shop tip
Lee Tolliver, Tok, Alaska
A mechanic accidentally put one pint too much oil in the transmission on one of my vehicles. Crawling under the vehicle and draining the surplus oil would have been a messy job.
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Lounsberry, Bordentown, N.J.
“The wooden block bearing on the feed auger of my Deere square baler dried out and was chattering so much that the noise was driving me nuts. To solve the problem, I added a grease fitting to the…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ron Paustian, Eau Claire, Mich.
“I put together this long hose funnel to pour oil into hard-to-reach vehicle transmissions. I cut the bottom off a 1-pint plastic fuel additive container and turned it upside down, then friction-fitted one end of a transparent hose…
Read the complete tip →From the archive · Full text
Reader shop tip
Wayne Bryan, Conesus, N.Y.
“We have a 100-ft. extension cord laying on our gravel driveway that leads to a fuel island. The cord was losing insulation from being driven over all the time.
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Smith, Cherokee, N.C.
“Plastic underarm stick deodorant containers can be used to make handy tool oilers. Once all the deodorant is gone, I remove the cap, fold a piece of 1/2-in. thick felt, and push it down inside the container. Then…
Read the complete tip →From the archive · Full text
Reader shop tip
David Prause, China Spring, Texas
“If you’ve got leaking transmission gearbox seals on your shredders or flail choppers, take the top off and fill partially with heavy gun grease. Check regularly after that and add the heaviest gear oil you can get just…
Read the complete tip →From the archive · Full text
Reader shop tip
Dean Weatherly, Clinton, Ark.
“When I buy a new electric drill, grinder or saw, I open up the gearbox and grease it with high temperature grease. Most of these tools are now made in China and they don’t put enough grease in…
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Swensen, Yankton, S. Dak.
“When I change oil, I wait until there are just a few threads left before the plug comes out and then I attach a vice grip to the plug to keep my fingers from getting burned. It also…
Read the complete tip →From the archive · Full text
Reader shop tip
Jay McCaman, Sand Lake, Mich.
“In a recent issue a reader complained about hydraulic oil transferring from the reservoir to the differential on Case 300 and 430 to 630 tractors. I worked at a Case dealership for 16 years and usually leakage of…
Read the complete tip →From the archive · Full text
Reader shop tip
Keith Ford, Houston, Mo.
“Since I repair a lot of riding mowers, I have a pile of inoperative solenoids. A couple weeks ago I was looking through them carefully and noticed that most every one was of the 4-terminal type with the…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Fulfs, Winslow, Ill.
Fulfs likes the idea of having shop equipment on wheels.
Read the complete tip →From the archive · Full text
Reader shop tip
Lynden Jenkins, Freedom, Wyo.
“We put a 5010 Deere tractor front-end under the front of a Deere 4020 to make it a better loader tractor. The 4020 front axles just weren’t strong enough. We could never break the 5010 axle.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Robert McMahon, Knoxville, Tenn.
“I needed a large hold-down clamp on my welding bench for fabrication work, so I made one by modifying a ‘Stronghand’ F-style clamp.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Robert McMahon, Knoxville, Tenn.
“I also made some cups that fit onto the clamp pads for holding accessories. I started with 1.625-in. ID tubing and 3/8-in. steel plate and drilled and tapped it. The tubing is slit so that it friction-fits the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Steve Nichols, Galesburg, Ill.
“When I wire a trailer, I have learned to wirenut the connector pigtails to the main wiring because the plug-in connector ends get corroded or damaged a lot. This way, I can just disconnect them easily and wirenut…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Steve Nichols, Galesburg, Ill.
“To protect the plug-ins when not using the trailer, I fasten an extra female connector (the part that goes on the vehicle) to the tongue of the trailer and plug the connector into it to keep it from…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Andy Sewell
Our friend Andy Sewell in England recently sent us photos of a German-made channel lock pliers that he modified for his own use by extending the jaws.
Read the complete story →From the archive · Full text
Feature story
Featured source: Roger Gutschmidt
“I recently went through my 9760 STS Deere combine in my shop. These newer series combines are never going to make it to 5,000 hrs. like their predecessors, the 8820 and 9600. The combine junkyards will soon be…
Read the complete story →From the archive · Full text
Feature story
Featured source: Roger Jones
A lot of people would never think to look for a solution like the one Roger Jones came up with for his Toyota pickup.
Read the complete story →From the archive · Full text
Feature story
Featured source: Clair Wilson
Clair Wilson makes pressing big steel pieces look easy with his double carriage, dual cylinder with independent action, chest-high press. Overbuilt doesn’t begin to describe the “ship-channel” construction of the press at his Wilson Seedtime and Harvest shop.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Jim Schmidt
Jim Schmidt, Western Welding, Cordell, Okla., has a full-time business custom building flatbeds for pickups from scratch – and he can’t keep up with the demand.
Read the complete story →From the archive · Full text
Feature story
Featured source: Lee Tolliver
“My Bobcat has a couple air filters on it that cost $26 to $27 apiece and when I’m on a job, I can go through a set or more in a week. I don’t like throwing them away…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
By Roger Meihak
Featured source: Roger Meihak
I recently decided to tile my shop floor. I thought it would make the floor easier to clean and make the shop brighter. Dirty cement absorbs a lot of light. But a shop floor also takes a beating,…
Read the complete story →From the archive · Full text
Feature story
Featured source: Paul Peyton
Paul Peyton didn’t want to spend the money for a new solid state ignition module for his 1960’s Sears Suburban garden tractor, so he found an internet site that provides complete instructions for an innovative fix. He used…
Read the complete story →From the archive · Full text
Reader shop tip
Arthur Peabody, Upton, Wyo.
“A couple of matchsticks saved me $940. That’s what my Ford dealer wanted to charge me to fix a miss in my 2000, 7.3-liter Power Stroke engine. We had already replaced the valve cover, gasket and more on…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Ben D. Marek, New Ulm, Texas
“I broke a hoe handle. To repair it, I used a hacksaw to cut a slot lengthwise in a 12-in. long piece of pvc pipe and slipped the broken ends of the handle into either end. I applied…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Ben D. Marek, New Ulm, Texas
“I got tired of long-handled tools sliding around in the bed of my pickup so I made some brackets out of 1/2-in. wide flat metal and mounted them over the wheel well, attached with screws to pickup box.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bruce Buckmaster, Rogue River, Ore.
“To remove a seized pulley from a shaft, I heat the pulley and melt wax from a candle onto the heated pulley shaft. Then I can remove the pulley easily.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Bruce Buckmaster, Rogue River, Ore.
“I had problems with flat tires on my hay rake. So I had the tire shop send the wheels and tires off to be foam-filled. After that, the tires lasted until the cords inside started showing.”
Read the complete tip →From the archive · Full text
Reader shop tip
Chris Despain, East Peoria, Ill.
“To remove stubborn bearing races from hubs/drums in medium and heavy-duty trucks, I stuff wet rags in the well of the hub backed up against the race, then weld a bead around the race where the tapered bearing…
Read the complete tip →From the archive · Full text
Reader shop tip
Darry Markle, Claresholm, Alberta
“Mounting four 8-in. pneumatic wheels on a pallet makes it easy to move my gas-powered compressor and generator around my shop. I mounted a pair of caster wheels on one side and fixed wheels on the other.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Earl Lumbra, Montgomry Center, Vt.
“I put a jack from Tractor Supply on my home-built wood splitter to hold the front up when it’s not connected to a tractor. I should have done that 30 years ago.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Earl Lumbra, Montgomry Center, Vt.
“I recently installed GFCI outlets in my shop to protect against electrical shocks. Peace of mind.”
Read the complete tip →From the archive · Full text
Reader shop tip
Garry Hoffman, Killaly, Sask.
“Anyone who has ever used a 3-jaw puller knows how frustrating the experience can be. However, wrapping the jaws with a vise grip chain changes the whole experience.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Alford, Edwardsburg, Mich.
“I installed a Pertronix electronic ignition and coil on my 1954 Ford 800 tractor and it worked out great. That old tractor has never run so well (www.pertronix.com).
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Alford, Edwardsburg, Mich.
“Fuel shut-offs on Ford 800’s always start leaking and replacements are getting expensive. You can remove the stop pin, replace the O-ring, and then tap in a small screw to take the place of the stop pin. This…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Kerry Kligora, Mineral Point, Wis.
“I cut a lot of wood for our boiler every year. At the end of the season, I sharpen all the chains and gauge all the rakes prior to storing, but sometimes they rust during the off season.…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Kerry Kligora, Mineral Point, Wis.
“Also, I always keep an old bar for each saw around in case I need to go after stumps
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Miles Parkkonen, Marquette, Mich. (www.paintscrubber.com)
His new Paint Brush Scrubber makes it easier to clean paint brushes, rollers and pads. The small, wooden tool has a grooved washboard surface. Brushes are cleaned by scrubbing them back and forth at a 45 degree angle,…
Read the complete tip →From the archive · Full text
Reader shop tip
R.A. Smith, Piketon, Ohio
“The power steering on my 2002 Sebring sedan was getting difficult to use. It would ‘stick’ at lower rpm’s. I talked to a friend who had the same problem with a 2007 Toyota Tacoma. His dealer wanted $1,200…
Read the complete tip →From the archive · Full text
Reader shop tip
Ray Webb, Emlenton, Penn.
“Here’s how I remove a 3/4-in. broken stud. First, I drill a 1/4-in. pilot hole in the end of the stud. Then I take a 1/2-in. right hand drill bit and run it in reverse to back the…
Read the complete tip →