John Rochester
“Store a 4 by 4 and a plank behind the seat until needed. Use them for parking on a hill or changing a tire.”
Read the complete tip →5957 shop tips and stories · page 2 of 100, newest issues first.
“Store a 4 by 4 and a plank behind the seat until needed. Use them for parking on a hill or changing a tire.”
Read the complete tip →Rich Meyer, inventor of The Tool Swing, aims to improve the functionality of your workbench. This specially designed workshop aid quickly and easily swings up a vise, bench grinder, sander, chop saw or other tool, then swiftly unlatches…
Read the complete story →While browsing online recently, the Makita LF1000 Flipover saw caught our attention. This innovative saw serves two functions, acting as both a miter saw and a table saw by flipping the work surface over. It’s built for both…
Read the complete story →Winching non-operational equipment from yard sites and road ditches is at the core of Cole Hardman’s business. To handle these sometimes difficult tasks, he used to mount a winch near the front of his flatbed trailer, but it…
Read the complete story →Tony Foale says the Startrite drill press he’s owned for years has always performed well, except for one frustrating feature: raising and lowering the table is always difficult because the press lacks a rack-and-pinion table lift.
Read the complete story →“I’m submitting this as a licensed electrician. When doing a minor remodel and installing lighting outlet boxes in a finished ceiling, be certain that not only is the box where you want it, but also make sure that…
Read the complete tip →“Bolting a gauge wheel from a cultivator onto a farm gate makes it a lot easier to open and shut the gate.”
Read the complete tip →“I had an 8.5-hp engine on a walk-behind mower that wouldn’t run right unless the choke was half on. So, I drilled out the gas jet. It was too much gas. I bought a new jet, same deal.…
Read the complete tip →“I keep a set of cheap wrenches so when I need one with a special angle or bend, I don’t destroy one from my good set. You might only need that special angle or bend once.”
Read the complete tip →“When one of my older shop-type vacs (with 2-in. suction and exhaust/blower ports) failed, I cut the cord off and turned it into a ‘pre-filter’ for my better vac.
Read the complete tip →“When removing fittings from air compressor systems, let out the air pressure before loosening.
Read the complete tip →“I use spring hand clamps to hold the hose when filling a sprayer.”
Read the complete tip →“When my TurboTorch fell over, the housing broke. I repaired it with a piece of aluminum strap 1/16 in. thick by 1 in. wide by 13 in. long.
Read the complete tip →“Also, I clean the orifice with a strand of copper wire from a lamp cord.”
Read the complete tip →“To repair the wobble box on a New Holland 489 haybine, remove the header first. It’s not that hard, and it makes the job a lot easier.”
Read the complete tip →Just when you thought you had all the flashlights you needed, Milwaukee introduced the M12 Underbody Light. The light features two swivel points that offer 300 degrees of horizontal rotation and up to 180 degrees of vertical rotation.…
Read the complete story →Like most farmers, Gerald Peters occasionally faced the prospect of replacing the bearings on the packers of his air drill.
Read the complete story →The Devil’s Finger from Jersey Discount Tool Co. (JDTCo.) puts a mini-pry bar in every toolbox. Handy for prying loose oil pans or other small jobs, it’s a sturdy alternative to indexing pry bars.
Read the complete story →Dexter Brahn has made his shop vice more useful by adding additional tools and storage to keep things close by when working.
Read the complete story →Drawing from over 20 years of hunting experience and a career as an electrical lineman, Chris Rodgers invented a handy carry-around tool.
Read the complete story →Holding a flashlight while trying to make a repair is never easy. Traditional headlamps often have a narrow beam of light.
Read the complete story →Save’Em System products are designed for wood shop safety. Bill Niichel, who has a lifetime of cabinetmaking experience, designed attachments for miter and table saws.
Read the complete story →“To protect fingers when using a 7-in. wafer wheel on a 4-in. grinder, I took the 4-in. guard and enlarged it to fit the 7-in. cutoff wheel. Much safer.”
Read the complete tip →“I made a swinging air, electric and light reel for the center of the shop between two overhead doors. It originally had bearings on the main pivot that I had to cut off. It rotated too easily. I…
Read the complete tip →“When plastic grease fittings on PTO shafts are broken, use a needle point (designed for greasing sprockets on chainsaw bars) instead of the standard grease couplers. The needle point also works on broken or damaged grease fittings. You…
Read the complete tip →“I’ve read in FARM SHOW about people having problems with the teeth breaking on their Troy-Bilt walk-behind sickle bar mowers. I have a 1991 model and replaced the bar that holds the cutting teeth with one I took…
Read the complete tip →“When you buy a can of boiled linseed oil, pour it into another empty can, leaving a small amount in the original can. Flip it on its side and use an old toothbrush to dip out oil for…
Read the complete tip →“I checked the alignment on one of our trucks, and all the joints were tight. After jacking up the wheels, I cut a slot in a piece of Masonite, tacked it to a 2 by 6 cut at…
Read the complete tip →“For many years, I’ve used 1/2-in. two-hole conduit clamps (pipe clamps) to fasten wire to wood fence posts, using dichromate-coated ‘gold’ screws. This practice makes fence repair much easier. I use this system for smooth and barbed wire.…
Read the complete tip →“I purchased a piece of equipment that required a 12-volt battery for power. It had two clamps for positive and negative, plus two small alligator clips. I used battery post clamps for large cables. I cut down 3/8-in.…
Read the complete tip →“When I disassemble and reassemble small things like carburetors, I do it in a cardboard box. This way, if a spring jumps or parts fall out, they are easy to find and retrieve. The box is clean, and…
Read the complete tip →“My gas-powered wood splitter leaked at the gasket that joins the carburetor to the engine. I rubbed hydraulic oil on the leak. It’s four years later, and I haven’t had any more issues with it.”
Read the complete tip →If you’re looking for a quick and easy way to store air tools in your shop, Air Wrangler modular locking pneumatic holders may do the trick. The 1/4-in. quick-connect plug patent-pending design locks tools in automatically.
Read the complete story →Socket Straps can keep wrenches, sockets, screwdrivers and pliers, as well as nuts, bolts and screws, in place. The magnetic strips come in various sizes and feature powerful magnets.
Read the complete story →Windshield WOW! makes it possible to clean both sides of your windshield simultaneously.
Read the complete story →WASH+OUT® attaches to a standard water bottle, and with a squeeze, it can flush out eye and face irritants in seconds.
Read the complete story →The WaveCel impact mitigation system aims to keep your head safe when it’s most at risk. This patented material adds a protective layer to the helmet’s interior, lowering your risk of traumatic brain injuries on the job.
Read the complete story →The Kneel-It is an ergonomic low-work posture-support device for anyone who kneels for prolonged periods. It’s well-suited for shop work and is designed to relieve strain and decrease knee injuries.
Read the complete story →The Little Giant Conquest ladder is a new multi-position ladder with added features aimed at helping you get work done.
Read the complete story →The handheld BLSTRsander removes paint, rust and more from wood, metal, glass and brick, no matter how complex the surface. Unfortunately, it’s not yet available in North America. The corded, no-compressor sandblaster solved a common problem faced by…
Read the complete story →The Tite-Reach extension clamp is made for those tough-to-reach spots your hand can’t reach or may be too hot to touch.
Read the complete story →The M12 Fuel 1/2-in. by 18-in. bandfile is the first cordless bandfile that delivers pneumatic performance, size and features for professional automotive, industrial and metalworking users.
Read the complete story →Inspired by the classic oil filter design, the Clutch Gear mug is made of stainless steel and has double-wall vacuum insulation.
Read the complete story →Mike Glodosky developed the Strong Arm 5 portable drill press after spending hours drilling at his job. He was tired of drilling holes by hand, finding that the drill would slip and slide around, and he also found…
Read the complete story →Edwin Egli of New Salem, N.D., built a shop stand for his air and electric tools.
Read the complete story →Connecting hydraulic couplers when line pressure has built up can be nearly impossible. The QC Mate Quick Coupler Hand Clamp from XBoom solves the problem quickly and safely.
Read the complete story →A friend called Frank Surber a few years ago and asked if he could install a clutch and rear main seal in his Mack truck. Surber said, “Sure, come on over.” Then he realized he didn’t have the…
Read the complete story →“I removed the carburetor on my Stihl MS 291 using a cheap deep-well socket and turned it down to fit the holes.”
Read the complete tip →C.J. Shortridge of Dagsboro, Del., made a homemade barrel bung wrench that turns into an adjustable multi-tool.
Read the complete story →The IQ vise™, introduced by Work IQ Tools™, puts a modern spin of functionality and infinite positioning on a common farm shop tool. The unique design earned the 2024 Rising Star Award presented to the top new product…
Read the complete story →The new Wagner® Furno 550 battery-powered heat gun makes fixing frozen pipes, rusted bolts, and other challenges easy. As a leader in advanced paint applicators and heat guns, Travis Johnson, product manager, says the cordless heat gun lives…
Read the complete story →When the wood lathe he bought chattered with vibration, Norman Sieting got busy and built his own. With 2 by 2-in., 1/4-in. thick angle iron legs and a 4 by 6-in. angle iron bed, he didn’t worry about…
Read the complete story →“I did a simple table saw upgrade that has made woodworking much easier. I bolted two table saws together. It gives me a larger work surface. It also simplifies my woodworking.
Read the complete tip →“For most lawn tractors with a 2-cyl. engine, the engine needs to be completely removed from the tractor to replace a faulty ignition coil. To save the customer labor costs, after consultation and permission, I cut out a…
Read the complete tip →“If you have an old AMC/Jeep with low engine pressure, do a copper tube oil bypass under the intake manifold from the front oil passage to a drilled and tapped hole between the number six and eight cylinders…
Read the complete tip →William Greyerbiehl of Bad Axe, Mich., repurposed two broken XL tall shop fans for his workshop.
Read the complete story →“To help maintain fastener connections in high-vibration settings, I apply a lock washer, tighten it with the nut, and then drill a small hole in the bolt just distal to the nut to prevent the fastener from loosening…
Read the complete tip →“The 1 3/8-in. hydraulic fittings on our 332 Deere skid steer are tough to access. I heated and bent the end of the wrench 90 degrees, then used another wrench for a handle. It worked great.”
Read the complete tip →As a farmer, Shawn Peterson was frustrated with how long it took him to clean farm equipment air filters every day before heading to the field to harvest corn and soybeans. So, 14 years ago, he built his…
Read the complete story →The Anex offset socket extension lets you use your power ratchet/driver in places it wouldn’t otherwise fit. It’s just over 9 in. long, less than 2 in. wide and only 3/8 in. thick, so it gets into tight…
Read the complete story →