Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Tools

5957 shop tips and stories · page 86 of 100, newest issues first.

From the archive · Full text
Reader shop tip 2 of 3

Tom Dutton

Individual tip 2 of 3 from this reader’s published contribution.
Tom Dutton, Menoken, N. Dak.

“I made a bin auger from an old 6-in. dia. auger that had a worn out tube. I used two small U-joints from an old front-wheel drive car to make the upward joint in the auger just outside…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Tom Dutton

Individual tip 3 of 3 from this reader’s published contribution.
Tom Dutton, Menoken, N. Dak.

“I also made a baler pickup lift to reduce the number of teeth we break. It’s made from an old hydraulic cylinder and scrap iron bolted to the frame of our OMC baler. We bolted a short piece…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Dale Spoerl

Individual tip 2 of 2 from this reader’s published contribution.
Dale Spoerl, Elizabeth, Ill.

“I used scrap steel to make a 36-in. wide metal bender that lets me bend sheets of metal at a 90 degree angle. It’s equipped with a hinged handle on each side. I place the bender in a…

Read the complete tip →
From the archive · Full text
Reader shop tip

Hard-To-Find Bolts

Hard-To-Find Bolts, 1537 North Point, Oshkosh, Wis. 54901 (ph 888 236-9013; fax 9014)

“Our company offers a low cost source of bolts, nuts, washers, screws, pins and other odd fasteners. It was created for one purpose - to provide fasteners to the customer in the exact quantities the customer requires, not…

Read the complete tip →
From the archive · Full text
Reader shop tip

Roger Kuntz

Roger Kuntz, K-Tech, Rt. 1, Box 69, Grainfield, Kan. 67737 (ph 785-673-4728)

“I used to be service manager at a large farm tillage plant that made blade plows and I often found that the cause of customer complaints would be equipment not properly set up for field use. The key…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Curtis L. Barron

Individual tip 2 of 2 from this reader’s published contribution.
Curtis L. Barron, Miles, Texas

“Also, I save old 34-in. dia. tractor inner tubes and cut a 12 in. cross section out of the tubes to make giant rubber bands to hold black trash bags on ventilation fans during winter. I also use…

Read the complete tip →
From the archive · Full text
Reader shop tip

Dakota Tools, Inc.

Dakota Tools, Inc., Box 261, Orford, N.H. 03777 (ph 888 597-3624; fax 603 353- 4836)

“Our new Multi-Tip Driver allows you to drive any size socket with no need to stop when switching from 1/4, 3/8, or 1/2 in. One model fits in a standard drill chuck. And our ratchet adapter snaps onto…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

George Hayes

Individual tip 2 of 2 from this reader’s published contribution.
George Hayes, Friendsville, Pa.

“Another good idea I had was putting up a 3 by 5-ft. maintenance chart from a local shop (the chart is sponsored by Big A filters). I’ve listed all tractors, pickups and other equipment on these and include…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

William P. Stephenson

Individual tip 2 of 2 from this reader’s published contribution.
William P. Stephenson, Huntington, W. Va.

“One way we made our shop more comfortable was by laying standard window fans up in the rafters facing down. In summer, on high speed, a cooling breeze blows downward. In winter, at low speed, the warm air…

Read the complete tip →
From the archive · Full text
Reader shop tip

Arthur Koehler

Arthur Koehler, BLH Electronics Inc., Canton, Mass.

BLH manufactured the draft sensing pins used on Case-IH tractor 3-pt. hitches - Magnums up through Steiger 4-WD’s - until Case recently took its business overseas. The two clevis-like pins sense the draft on the lower two 3-pt.…

Read the complete tip →
From the archive · Full text
Reader shop tip

Steve Houge

Steve Houge, Schuling Hitch Company, Ames, Iowa

“The big difference between the load boosters for pickups we sell and other systems on the market is that ours never needs adjusting once it’s installed,” says Steve about his Timbren “Little Rubber Load Booster” kits.

Read the complete tip →