From the archive · Full text
Feature story
Featured source: Kenny Vandeventer, Ottawa, KS
“Recently I borrowed my grandson’s mower trailer and while I had it I decided to repair the fold-down ramp. The problem was that after I finished the repairs it was so heavy I could hardly lift it,” says…
Read the complete story →From the archive · Full text
Feature story
Featured source: Roger Podoll, Wautoma, Wis.
Roger Podoll has found multiple uses for old radiator cores. He sticks them in front of the OEM radiator core on skid steers and tractors as a pre-cleaner and also uses them as filters in his shop.
Read the complete story →From the archive · Full text
Feature story
Featured source: Tony Bunniss, Webster, Minn.
Tony Bunniss built an extension on his tuck-under garage to expand it to a 4-car garage, which Bunniss heated and air-conditioned. The original garage section then became a machine shop.
Read the complete story →From the archive · Full text
Feature story
Featured source: Lynn Thomas, Salmon, Idaho
Idaho rancher Lynn Thomas needed to build several miles of fence with limited help. At 78 years old, he needed to come up with a new way to get the job done. Wire unrollers he’d seen either unrolled…
Read the complete story →From the archive · Full text
Feature story
Featured source: Tie Boss, LLC, Piqua, Ohio
U.S.-made. Easy to use. Lifetime warranty. Those are things customers appreciate about the Tie Boss. It’s a handy tool for tying down or hoisting up loads.
Read the complete story →From the archive · Full text
Reader shop tip
Carlton Dubberly, Waycross, Ga.
“To help hold a nut or screw on a tool, keep a toilet was ring around and just put a touch of the wax on the tool. It sticks well but is not as messy as axle grease…
Read the complete tip →From the archive · Full text
Reader shop tip
Carrol Jones, Louisa, Va.
“I needed a metric allen wrench for a job but didn’t have one. Instead, I used a metric bolt head, with 2 nuts on the bolt locked together down at the head. I put a wrench on the…
Read the complete tip →From the archive · Full text
Reader shop tip
Daniel J. Moore, Bellingham, Wash.
“I put a 1 7/8-in. ball hitch on one side of my tractor loader bucket and a 2-in. ball on the other side. Makes it easy to move trailers around the yard.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Dennis Schenk, West Burlington, Iowa
“To install hard-to-reach spark plugs, I use a short length of rubber hose that fits tightly over the end of the spark plug. Lets me put the plug in the hole and get it started.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Dennis Schenk, West Burlington, Iowa
“If you’ve got a pin clip that’s hard to remove, just attach a short length of small chain to it that you can easily grab onto. You can leave it on the pin all the time.”
Read the complete tip →From the archive · Full text
Reader shop tip
Elias Wolf, Mancelona, Mich.
“I store paperwork like warranties and owner’s manuals under the liners in my tool chest drawers. They stay clean but are always handy.”
Read the complete tip →From the archive · Full text
Reader shop tip
George Egas, Dublin, Ga.
“Some time back FARM SHOW showed a way to install a rubber tubeless tire valve stem in a plastic gas can, leaving the ‘core’ out so it provides a vent when pouring out fuel. It’s a great idea…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gerald Wright, Pendleton, Ky.
“While shopping at a tool outlet store, I found a Dewalt adapter that lets you fit the new 20-volt lithium ion batteries into the old 18-volt tools. It gave my old tools new life. You can pick up…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gerald Wright, Pendleton, Ky.
“On another topic, with Sears closed I’ve discovered that we can’t return our old Craftsman tools under the lifelong warranty at Lowes or other stories that sell Craftsman tools. They won’t honor the warranty.”
Read the complete tip →From the archive · Full text
Reader shop tip
Gordy Kessler, Wolverton, Minn.
“On one of my Allis Chalmers WD tractors the coil in the magneto would shut down when it got warm and I couldn’t start the tractor again until it cooled off. It would have been expensive to repair…
Read the complete tip →From the archive · Full text
Reader shop tip
Harold Wells, Gridley, Ill.
Harold is impressed with “Water Weld” from JB Weld.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Jim Ellinger, Hanna, Ind.
“To make it easy to change tires around the farm, I mounted a small Harbor Freight tire changer to the receiver hitch on my pickup.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Jim Ellinger, Hanna, Ind.
“To make rubber cutting edges on snowplows or other equipment, and to line pickup beds, go to Tractor Supply Co. and spend $40 on a 4 by 6-ft. horse stall mat. You’ll save hundreds of dollars.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Jim Ellinger, Hanna, Ind.
“One of the handiest things in my farm shop is an electric winch that hangs from the trusses in my shop. Great for changing mower blades and other lifting chores.”
Read the complete tip →From the archive · Full text
Reader shop tip
Marvin M. Smith, Hooper, Neb.
“I always had trouble with the drive belt on the tiller behind my 149 Cub Cadet garden tractor. To solve the problem, I rotated the gearbox and ran a driveshaft from the gearbox to the tiller drive. That…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Morse Mfg. Co., Syracuse, N.Y.
If you buy a lot of product in 55-gal. drums, you need a bung wrench like this one from Morse Mfg. Sells for $24.45.
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Faber, Tiffin, Ohio
“To make a counterweight for my Deere 5085E tractor, I took the rear counterweight from a non-running forklift that I bought at an auction. I welded up brackets to fit and then drilled and tapped holes as needed.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Timothy Rankin, Middlebrook, Va.
“The fuel lines on my 1991 Chevy Scottsdale were rusting through and would have been very expensive to replace. So I ran rubber fuel lines instead of steel and slipped a piece of flexible steel conduit over the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Timothy Rankin, Middlebrook, Va.
“After a friend of mine lit a trash barrel on fire in his shop while cutting metal, I realized that could easily happen to me, too. So I made a lid for my barrel out of flat sheet…
Read the complete tip →From the archive · Full text
Reader shop tip
Albert Schollenberger, Egg Harbor City, N.J.
“When I have to replace bearings on equipment, I put the new bearings in the freezer for a couple hours. The cold shrinks them so they slide easily into place with no force needed.”
Read the complete tip →From the archive · Full text
Reader shop tip
Clifton Lamar Martin, Port Trevorton, Penn.
“I built a stand off one corner of my workbench to hold a truck tool box so I can have tools handy without cluttering up my workbench.”
Read the complete tip →From the archive · Full text
Reader shop tip
Clinton Kenney, Creighton, Mo.
“For years I’ve used a syrup bottle to put bar oil in my chainsaw. I just flip the cap and fill the tank. No funnel needed. The cap keeps the dirt out.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Cory Pleschourt, Northfield, Minn.
“I hate ‘pushed in’ grease zerks. More often than not they will eventually pull out with the grease gun end when done greasing. To solve the issue permanently, I thread the zerk mounting hole and install threaded grease…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Cory Pleschourt, Northfield, Minn.
“I was tired of always having to dig around in my tractor toolbox to find what I was looking for. It seems like every time I needed something it was at the bottom of the toolbox. So I…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
David Van de Weert, Geneseo, N.Y.
“A real time-saving tool for me is to use a roller chain breaker. Gets repairs done faster.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
David Van de Weert, Geneseo, N.Y.
“When it comes to repairs, I say don’t fix whatever it is too many times. Sometimes a piece of equipment is just worn out.”
Read the complete tip →From the archive · Full text
Reader shop tip
Don Bender, Middleville, Mich.
“To seal caulking tubes, I melt candle wax and dip the end of the tube in it 3 to 4 times. The wax seals silicone caulk almost as good as the factory seal.”
Read the complete tip →From the archive · Full text
Reader shop tip
Donald J. Tarolli, Red Creek, N.Y.
“Need small clamps for light work? Try using spring-type clothes pins. They really work great.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Elton Brubacher, Thorp, Wis.
“When loosening the large nut that holds the pulley on top of a lawnmower deck spindle, hold onto the blade rather than the pulley and use a large impact wrench to loosen the nut.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Elton Brubacher, Thorp, Wis.
“I’ve found that having a self-retracting air hose reel makes using air-powered tools a breeze, even if you don’t use them regularly.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S.Dak.
“I’ve been changing my oil in my vehicles for decades. For most of the time I’ve used front wheel ramps and a creeper, but the creeper gets caught in the cracks of the concrete, extension cords get under…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S.Dak.
“With 4 boys and their vehicles along with my pickups and my wife’s vehicle, sometimes it gets difficult to remember how many quarts of oil go into each vehicle. I use a black magic marker to write the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
George W. Steve, Lake Lynn, Penn.
“I added a 12-volt inverter to my McCormick X4.40 tractor to be able to run small power tools in an emergency.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
George W. Steve, Lake Lynn, Penn.
“I had to remove the pto shield on this tractor in order to have room to work. Wish they would make a hinged pto shield that would lift out of the way.”
Read the complete tip →From the archive · Full text
Reader shop tip
Jesse Barley, Tyrone, Penn.
“In winter our frostless hydrant would freeze up even with heat tape and insulation wrapped around it. My wife started draping a couple feed sacks over it, with one sack inside the other. One is the newer kind…
Read the complete tip →From the archive · Full text
Reader shop tip
Leroy Oberholtzer, Greenwich, Ohio
“I have found that when using my shop press to remove or install bushings and bearings, that impact sockets make great punches for pushing them in or out.”
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Ledeboer, Silver Lake, Kan.
“I was getting ready to paint my propane tank and had to find a way to use a wire brush on the bottom of the tank where there was only about 3 in. of clearance. I took a…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Sizelove, Earlsboro, Okla.
“My Grandpa has made hundreds of tools in his lifetime. He asked me to submit this one that he whipped up recently to FARM SHOW. It’s a pto shaft quick-connect tool. He made it with an old pair…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Braddock, Dyer, Tenn.
“One of my most useful best buys around the farm are these small dish pans. They hold about 2 gal. and are good for holding just about everything from water for chickens to tools and all kinds of…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Keil, Bellevue, Iowa
“My 275 Deere 10-ft. disk mower had a problem with always tripping. I finally cured the problem by welding brackets on it and used two big bed springs to get it to stay in place instead of kicking…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Syntex Industries, Humbolt, Iowa (www.syntexindustries.com; ph 515 332- 3265)
Tarp manufacturer Syntex makes these 18-oz. vinyl-coated pallet covers that have an anti-mildew treatment and UV pigments. D-rings and grommets help tie them down during transport. The company sells a lot of them for covering seed bags on…
Read the complete tip →From the archive · Full text
Reader shop tip
Tom Calvert, Ethridge, Tenn.
“Old fertilizer barrels have a tendency to rupture when you put tons of liquid nitrogen in them. So I made 5 straps out of 3-in. nylon webbing with 6,000-lb. capacity. They wrap around the barrels starting at the…
Read the complete tip →From the archive · Full text
Reader shop tip
Tom Dufrense, Grant, Minn.
“On a recent trip to Montana in our diesel-powered RV, the engine suddenly seemed to lose power and run sluggishly. While going up a hill our speed would drop from 70 mph to 30 or so with little…
Read the complete tip →From the archive · Full text
Reader shop tip
Tommy Wilkerson, Whitesville, Ky.
“I bolted a piece of 2 by 2-in. aluminum angle iron to the back of my tractor and drilled a series of 3/4 and 1-in. dia. holes in it to hold all of my hitch pins. I also…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Wayne Hamel, Hopwood, Penn.
“I mow 6 acres every week with 2 rough riding tractors. It was killing me until I bought 2 gel foam seat cushions from Walmart. Ahhh, they feel good.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Wayne Hamel, Hopwood, Penn.
“I find that all sorts of defects in lumber can almost disappear if you put a little glue into the void and then sand over it. Allow some time for the sawdust to bond with the glue.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Art Martinez
It’s only logical that Art Martinez would build a high-performing engine for his own enjoyment since he’s part owner/operator of PSP Diesel, a performance diesel business in Houston. His business partner Richard Alvarado says Art’s 6.0L Powerstroke has…
Read the complete story →From the archive · Full text
Feature story
Featured source: Melvin King
The Milwalt battery adapter is compatible with both Milwaukee 18-volt and DeWalt 20-volt batteries, making it easier for members of Plain Communities and people who live off grid to use the same adapter for appliances, lights and other…
Read the complete story →From the archive · Full text
Feature story
Featured source: Randy Emerick
PermaFlex fromSANI-TRED is a liquid rubber-like adhesive coating that can seal up just about any surface. Randy Emerick at SANI-TRED says its most important qualities are its penetration and its flexible elongation memory. That means it penetrates deep…
Read the complete story →From the archive · Full text
Feature story
Featured source: Doug Andersen
For Utah-based truck driver Doug Andersen, watching TV’s Shark Tank combined with his wife’s good-natured prodding was the inspiration he needed to come up with his “wheel in a wheel”, a new twist on steering wheel spinners.
Read the complete story →From the archive · Full text
Feature story
Featured source: Greg Waldie
“After moving to town and not having a loader tractor anymore to lift the front of my riding mower, I tried several ways to get the job done - including using hi-lift jacks and several types of ramps,”…
Read the complete story →