Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 23, No. 3 (1999)

Vol. 23, No. 3 (1999)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 37–39

51 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Mike Graham

Mike Graham, Edison, Ohio

“You can fix a loose head on any size wooden handled hammer using this simple, low-cost method.

“You simply apply JB Weld generously to the end of the handle and inside the head, then put the head back on the handle and reset the head. I first clean the handle thoroughly with sandpaper or steel wool. Likewise, I clean up the inside of the head with a small wire brush. In 24 hours, after the JB Weld sets, you’ve got a hammer that’s as good as new.

“I’ve also used this repair on a couple of 4-lb. sledges I use to break up firewood. It’s a permanent repair.”

From the archive · Full text
Reader shop tip

Ronald J. Fitzgerald

Ronald J. Fitzgerald, Seely’s Bay, Ont.

Ronald’s come up with a foolproof way to remove bolts that break off flush, such as broken bolts in engine blocks.

“I take a nut the same size as the broken bolt and hold it over the bolt with a pliers. Then I take my MIG welder and weld the hole in the nut full, heating the nut red hot. When you’re finished, just as the color’s going out of the nut, take a wrench and turn out the bolt by the nut. It’ll work every time, guaranteed.

“In cases where you’re concerned the weld will stick to the surface around the broken bolt, first place a brass or copper washer over the broken bolt end and apply a wee bit of weld to build it up. Then use the same procedure described above.

“I’ve removed broken bolts this way ever since I got my first MIG welder years ago. It’s never failed.”

From the archive · Full text
Reader shop tip

Allen Polyock

Allen Polyock, Zenda, Wis.

You can keep air brakes on trucks and trailers in top condition using Allen’s simple maintenance technique.

“I’ve used it on all the trucks we’ve owned over the past 30 years and it works great. I take off the main feed line of the compressor at the engine and let the air out. Then I simply pour 1/2 pint of brake fluid into the line and reassemble the system. The brake fluid, which does not harm rubber, circulates through the lines to prevent internal rusting and to ensure valves work properly. It also prolongs valve life.

“I do this twice a year, once in the fall and once in the spring.”

From the archive · Full text
Reader shop tip 1 of 2

Jared Metzger

Individual tip 1 of 2 from this reader’s published contribution.
Jared Metzger, Steen, Minn.

“To put 90W oil into hard-to-reach gearboxes, I put an old milk inflation on the end of a funnel that I fill with oil. The inflation can be bent to pour oil into even the hardest to get at spots. It also allows you to squeeze just the right amount of oil into the gearbox.

From the archive · Full text
Reader shop tip 2 of 2

Jared Metzger

Individual tip 2 of 2 from this reader’s published contribution.
Jared Metzger, Steen, Minn.

“I also make new gaskets for parts out of cardboard cereal boxes, cutting them to fit. They work as well as any store-bought gasket.”

From the archive · Full text
Reader shop tip 1 of 2

Donald Tryor

Individual tip 1 of 2 from this reader’s published contribution.
Donald Tryor, Bemidji, Minn.

Donald’s had no problem paying for his investment in his 12-in. metal lathe. He makes replacement parts for his 1959 Oliver 660 tractor.

“I made a new oil filter base that allows me to use Fram 3600 spin-on oil filters, which sell for $2, instead of the original filters, which cost $8 and have a tendency to leak around the gasket. I made the 3-in. dia. base out of cold rolled steel in about eight hours. It bolts onto the tractor and the Fram filter simply screws onto it.

From the archive · Full text
Reader shop tip 2 of 2

Donald Tryor

Individual tip 2 of 2 from this reader’s published contribution.
Donald Tryor, Bemidji, Minn.

“I also made a speed jet for the Oliver’s carburetor when I accidentally broke the original by overtightening it. Like the original, I made the 1-in. long, 3/8-in. dia. jet out of brass. It took about three hours and works as well as the original.”

From the archive · Full text
Reader shop tip

David Anderson

David Anderson, Burr Oak, Kan.

“I use a high-volume, gas-powered leaf blower I bought for $10 at a garage sale to unplug radiators in the field. I’ve used it to blow straw, grass and dirt off tractor radiators and the knotters on both my Deere 4900 and 4750 big square balers and the radiator on my Hesston 8500 swather. It’s a lot more compact than hauling an air compressor along to the field and it saves an immense amount of time over going back to the shop to clear radiators. That’s important to me because I’m in the custom baling business.”

From the archive · Full text
Reader shop tip

Gene Trybom

Gene Trybom, Lawrence, Kan.

Gene got tired of going back to his shop to get tool after tool and still not always having every one he needed. So he mounted a big tool chest on a shop-built trailer that he pulls to the field with his 4-WD ATV.

“I bought a big Craftsman tool chest with 15 or 16 drawers. I built a 26 by 40-in. frame out of 1 1/2 by 3-in. scrap metal and mounted the tool chest on the back. I fitted the front of the trailer with a small work table I made out of 1/4-in. thick steel plate and tapped a 1/4-in. dia. hole in the left front corner of the table so I could mount my 5-in. vise on it. I made a hitch for the trailer out of 1 1/2-in. sq. tubing. It telescopes from 18 to 25 in. and folds underneath the table when not in use. The trailer rides on two 5/8-in. dia. steel shaft axles fitted with 3 by 10-in. pneumatic tires. I made my own front wheel swivel assembly so the rig trails my Honcho 4-WD ATV perfectly.

“It saves a lot of time because you’ve got all your tools with you. And it cost less than $225 to build, including $180 for the tool chest, since I used mostly scrap materials.”

From the archive · Full text
Reader shop tip

Floyd Lebold

Floyd Lebold, Exeter, Maine

When the 28-in. rims on Floyd’s 1958 Allis D17 began to rust out, he modified them with a pair of 30-in. rims he’d had on an Allis 175.

“I cut the front edge of the flange of the 28-in. rim down until it matched up with the bottom edge of the 30-in. rim. I welded all the way around both sides of the rims. It’s a cheap way to get ‘new’ rims and increase tire size on your tractor. I went from 14.9 by 28-in. tires to 16.9 by 30-in. tires, which increases ballasting capacity and traction and improves stability.”

From the archive · Full text
Reader shop tip

Donald R. Nutt

Donald R. Nutt, Center, Mo.

“Hay kept wrapping on the spiral starter roller on my 1993 Vermeer Super J baler when it was first new. The problem was that the roller scraper was made of the same weight steel as that used on the company’s smaller 4-ft. balers. It just was not heavy enough to stand the pressure in the new larger, 5 by 6-ft. balers.

“To solve the problem, I reinforced the scraper with a 1 in. by 5-ft. piece of steel, 1/ 2-in. thick. I simply welded it to the scraper on edge to take full advantage of the 1 in. width. The modification gave me wrap-free baling ever since.”

From the archive · Full text
Reader shop tip

Floyd Stivers

Floyd Stivers, Stroud, Okla.

Floyd says a common problem on small block Chevrolet V-8 engines from the late 1960’s through the early 1980’s is this: The heat from the engine causes the cast iron exhaust manifolds to “draw up” so much that bolts cannot be started in the original holes when reinstalling them.

“To solve the problem, I came up with a bolt spreader tool consisting essentially of a bolt and a couple of nuts. It exerts several thousand lbs. of torque to spread out the manifold to its original shape and is ideal for tight spaces where a pry bar won’t reach.

“Get a bolt that’s a little shorter than the space you need to spread, then screw on a nut that fits the bolt threads. Put a slightly larger nut over the first and insert the tool into the area you need to spread. As you turn the smaller nut out, it, in turn, forces the larger nut outwards to spread out the exhaust manifold. The technique also works well for many other jobs, such as removing pulleys from engines.

“I’ve used this method dozens of times and it’s never failed - so long as you get everything lined up straight and the bolt and nuts don’t slip. Since I came up with the idea in the 1970’s, some tool makers have come out with a similar product, but mine is definitely less expensive and probably just as effective.”

From the archive · Full text
Reader shop tip

Fred Galehouse

Fred Galehouse, Doylestory, Ohio

“I came up with a handy way to put a connector link into roller chains. I tie a piece of string or cord to one link and then thread it back through a link on the other side and then back through the other side. When you pull on the loose end, the links come together. This works better than any roller chain tool I’ve ever seen.”

From the archive · Full text
Reader shop tip 1 of 2

Russ Wahl

Individual tip 1 of 2 from this reader’s published contribution.
Russ Wahl, Cut Bank, Mont.

“We mounted a 450 gal. bulk tank for motor oil overhead in our shop. The tank is split 50-50 to hold two different weights of oil. Gives us a lot more capacity so we don’t have to fill as often.

From the archive · Full text
Reader shop tip 2 of 2

Russ Wahl

Individual tip 2 of 2 from this reader’s published contribution.
Russ Wahl, Cut Bank, Mont.

“I also made a rolling shop light by putting caster wheels on the bottom of a steel wheel rim and then welding a vertical pipe to the top of the wheel. I put a light at the top of the pipe and mounted an electrical outlet on the side of the pipe.”

From the archive · Full text
Reader shop tip 1 of 3

David Lee

Individual tip 1 of 3 from this reader’s published contribution.
David Lee, Grand Junction, Mich.

“I had a blown gasket on the MCV control valve on the pto clutch pack on a 464 International tractor. I kept the problem from recurring by using a heavier 5/16-in. thick plate rather than the origianl 1/4-in. thick plate. This keeps the plate from flexing and blowing under pressure again. This fix would also work on 674, 684, 484, and 574 tractors, and probably other tractors in that series.

From the archive · Full text
Reader shop tip 2 of 3

David Lee

Individual tip 2 of 3 from this reader’s published contribution.
David Lee, Grand Junction, Mich.

“I always keep mineral spirits in a backpack sprayer to use to wash off engines and other greasy equipment as needed.

From the archive · Full text
Reader shop tip 3 of 3

David Lee

Individual tip 3 of 3 from this reader’s published contribution.
David Lee, Grand Junction, Mich.

Here’s another tip: In winter, I keep my pressure washer in a small cooler with a light bulb burning inside so it won’t freeze.”

From the archive · Full text
Reader shop tip

Allen Derry

Allen Derry, Zanesville, Ohio

“We re-pair our own baler belts by splicing short pieces of belting in place of the broken parts. We put fasteners on with a belt lacing tool we bought at a local hardware store. Thanks to this method, our baler belts generally last 4 times longer than they are supposed to.”

From the archive · Full text
Reader shop tip

Troy Sharpton

Troy Sharpton, Auburn, Ga.

“We had trouble with fans in chicken houses that weren’t running right. I drilled holes in them to accept grease fittings and solved the problem. Grease can take care of a lot of problems. Adding extra fittings is often a cheap fix.”

From the archive · Full text
Reader shop tip

James White

James White, Clark Fork, Idaho

“I have a 50-ton iron working machine in my shop that has virtually eliminated the purchase of acetylene gas. It’s used almost every day to make neat, quick repairs or fabrication of parts. It’ll punch holes up to 1 1/ 16-in. dia. in 3/4-in. thick bar and shear up to 3/4-in. thick bar 12-in. wide.”

From the archive · Full text
Reader shop tip

Chris Pluhar

Chris Pluhar, Miles City, Mont.

“I had problems with the front wheel king pin bearings on my 1982 Deere 4450 tractor. The bearings have gone out six times in the past four years. Each time they go out they ruin the bearing race seat. I finally solved the problem by using JB Weld to put the race back in.”

From the archive · Full text
Reader shop tip

Barry Zellitti

Barry Zellitti, Dao, Colo.

“I had trouble removing the battery from a 610 Bobcat loader. I solved the problem by notching the frame brace 1/2-in. deep along the length of the battery.”

From the archive · Full text
Reader shop tip

Lance Thiessen

Lance Thiessen, Peabody, Kan.

“Our 1993 Gleaner R-62 combine tended to chop up high-moisture milo heads which flooded the sieves with trash. The problem is that the cylinder bars in the combine are too aggressive. We solved the problem by putting a rotor from a Gleaner N-6 into the combine. The N-6 rotor is less aggressive so it chops the trash less and doesn’t flood the sieves. I understand this is now an option on newer machines.”

From the archive · Full text
Reader shop tip 1 of 3

Martin DeKlotz

Individual tip 1 of 3 from this reader’s published contribution.
Martin DeKlotz, Filer, Idaho

“On many tractors, you have to remove the muffler to take off the hood. The mufflers often rust to the manifold and must be destroyed to get them off. To prevent that problem, I apply a liberal amount of Permatex anti-sieze paste before installing the muffler. It comes off easy the next time.

From the archive · Full text
Reader shop tip 2 of 3

Martin DeKlotz

Individual tip 2 of 3 from this reader’s published contribution.
Martin DeKlotz, Filer, Idaho

“I also replace cracked or rusted metal hydraulic lines with hydraulic hose. It’s cheaper and holds up better.

From the archive · Full text
Reader shop tip 3 of 3

Martin DeKlotz

Individual tip 3 of 3 from this reader’s published contribution.
Martin DeKlotz, Filer, Idaho

“I have a shop table made of 3/4-in. thick steel plate. I place a kerosene heater under the table. It warms the table and everything on it. The heat rises all around the table so you can work comfortably with bare hands even with air temperatures in the 40’s.”

From the archive · Full text
Reader shop tip

J.D. Pearce

J.D. Pearce, Conway, Ark.

“I have an 847 New Holland round baler. Holes started opening up in the floor of the bale chamber. I ordered some wear plates from New Holland for $32 apiece. When they came in they wouldn’t fit. I returned them and went to the scrapyard and bought a bunch of flat steel 7 1/2-in. wide. I replaced all 7 plates for $9 total - a savings of $183.”

From the archive · Full text
Reader shop tip

Harvey Malon

Harvey Malon, Rapid City, S. Dak.

“Nuts, bolts, screws and small parts are always a problem to store. I’ve found that 1-gal. metal cans can help solve the problem. Cut out one side - using a sharp chisel seems to work the best. Then build a simple wooden cupboard with shelves as deep as the cans and as wide as you want. The vertical distance between cans should be about 1 1/2 times the depth of the cans so that you if you overload them you can still see what’s in them. Be sure to put a back on the cupboard. Mark the cans with a marking pen.”

From the archive · Full text
Reader shop tip

Charles Weyrough

Charles Weyrough, Alden, N.Y.

“I place a piece of door screening in front of the radiator on my tractor when mowing. It keeps seed and chaff from plugging it up while mowing. When the screen gets plugged, it’s much easier to just shake it out and replace it than it is to return to the shop and blow out the radiator with compressed air.”

From the archive · Full text
Reader shop tip

Art Spearman

Art Spearman, Hammond, La.

“I re-store old John Deere tractors. The smaller model L and M models were equipped with cast iron hub caps which are usually broken because they bolt on from the back. Used caps sell for $50 to $100 a set, if you can find them. Instead of buying them, I buy a pair of 6-in. hub caps from a truck supply company for $12. I cut the lips off and weld 3 1/2-in. bolts to the inside of the caps. After I paint them green you can’t tell by looking that they’re not cast iron.”

From the archive · Full text
Reader shop tip

Gary Peters

Gary Peters, Woodsville, N.H.

“You can use a tractor to roll up fence wire. I welded a 5/8-in. nut onto the center of the axle on the rear wheel. Then I screw in a piece of threaded rod and slip on a reel from a wire feed welder. I snug it up right against the wheel. Then I drive to the fence and block up the wheel with a 4 by 4. Then I put the tractor in gear and roll up the wire. Works great.”

From the archive · Full text
Reader shop tip

Ron Melchert

Ron Melchert, Seymour, Wis.

“I modified a tool from Snap-On that’s designed to pull cotter pins or seals. I added a slide hammer made out of round stock 4 to 5 in. long with a 1/2-in. bore. I slide it back against a ‘stop’ welded to the top of the tool. Makes seal and pin removal much easier than any other tool I’ve used.”

From the archive · Full text
Reader shop tip

Dave Herbranson

Dave Herbranson, Hawley, Minn.

“Our shop was converted from an old 2-story dairy barn. We removed the hay mow and added a home-built bifold door. We removed the stanchions and poured a new floor. I now use the old milk vacuum line to carry compressed air from a 60-gal. air compressor installed in the milk house. We use air tools a lot and the dairy barn made that easy.”

From the archive · Full text
Reader shop tip 1 of 4

Craig Froman

Individual tip 1 of 4 from this reader’s published contribution.
Craig Froman, English, Ind.

“Here’s a maintenance tip for Briggs & Stratton engines in mowers, tillers and other equipment. The bearing in the recoil starter often gets dry so the starter rope binds up and is difficult to use. Here’s how to solve the problem. Drill a 1/4-in. hole in the center of the outer recoil cover. Then drill a 1/8-in. hole in the second cover inside the larger hole. Then oil the inside bearing through the holes. Don’t put too much oil or it will gum up.

From the archive · Full text
Reader shop tip 2 of 4

Craig Froman

Individual tip 2 of 4 from this reader’s published contribution.
Craig Froman, English, Ind.

“When working on a car or truck, there’s often no good place to lay small parts or wrenches. I solved the problem by standing a sturdy, folding ironing board next to the vehicle. Makes a lightweight work table. Doesn’t scratch the paint. Make sure to get a sturdy board. The best thing is that it folds up out of the way when not in use.

From the archive · Full text
Reader shop tip 3 of 4

Craig Froman

Individual tip 3 of 4 from this reader’s published contribution.
Craig Froman, English, Ind.

“A used sickle section makes a good wedge to hold an ax head. Just sharpen both sides of the section and drive it in.

From the archive · Full text
Reader shop tip 4 of 4

Craig Froman

Individual tip 4 of 4 from this reader’s published contribution.
Craig Froman, English, Ind.

“To check for spark on a gas engine - large or small - I hook an electric fence tester to the spark plug wire and ground the other end to the engine. Then crank the starter. The tester I have tells me how strong the spark is.”

From the archive · Full text
Reader shop tip

Jim Bauer

Jim Bauer, Worden, Ill.

He uses an old squirrel cage fan from a furnace to efficiently heat his farm shop. He mounted the fan up near the ceiling and connected it to a duct that carries warm air from up by the ceiling down to the floor. He put a thermometer up near the ceiling so he can tell how warm it is up by the ceiling and whether or not it’s worth turning on the fan. Works great to keep warm air circulating evenly throughout the shop, Bauer says.

From the archive · Full text
Reader shop tip

Lloyd Meffert

Lloyd Meffert, Hettick, Ill.

Lloyd needed a way to square and align pieces of angle iron for welding and drilling so he made this handy clamp to fit into his vise. It consists of a flat metal plate with a short piece of 2-in. angle iron welded upright at one end and a large nut with a threaded rod welded to the other end. The threaded rod is fitted with a smaller piece of angle iron that fits into the larger, stationary piece. Whatever needs to be welded is positioned between the two pieces of angle iron and the rod is threaded down to hold them in place.

Lloyd says the clamp can also be used for round stock or pipe.

From the archive · Full text
Reader shop tip

Jay L. Smith

Jay L. Smith, Immokalee, Fla.

“Instead of taking the cab off of my 4-WD tractor to pull the transmission, I just put it up in the air about 2 ft. on ramps and dropped the transmission out the bottom. Took only about half the time.”

From the archive · Full text
Reader shop tip

J.T. Schmidt

J.T. Schmidt, Abbotsford, B.C.

“Here’s an idea that might help anyone experiencing loss of power on a car or pickup fitted with a catalytic converter.

“One day I tried to pass a semi going about 60 mph in my 1986 Cadillac and couldn’t do it. When I got home I started trying to figure out what was wrong. I know my car pretty good and decided that since there’s rarely a problem with the car’s fuel injection system, the exhaust system was probably the problem. I figured there was some kind of con-gestion or blockage going on so here’s what I did.

“With the engine running, I poured a jar of hot water slowly into the throttle body. Since the engine was hot, the water turned into steam which I figured would clean out the catalytic converter. I took the car for a spin right after I was done and sure enough, my problem was solved.

“As you add water you have to have your hand on the throttle and rev the motor at a pretty fast speed so you won’t stall the engine. The speed also helps to blow out the carbon as it’s cleaned out of the converter.

“I can’t say this idea will work in all cases but it’s worth a try and I don’t think it will hurt anything if it doesn’t work.”

From the archive · Full text
Reader shop tip

William R. Marrs

William R. Marrs, Arkansas City, Kan.

“I made these handy storage racks a couple years ago to hold nuts, bolts, washers, bearings and other odds and ends. They’re a big improvement over the mess of cans, boxes and sacks I used before.

“I used 20-in. dia. steel press wheels off an old Crustbuster drill. They originally faced each other on the axle, but I turned every other one around so each one faces up to hold parts. I used the original spacers on the axle and made additional ones out of plastic pipe to properly position the press wheels.

“I mounted the racks on 22-in. truck rims. Each one stands about 5 ft. high and holds up to 500 lbs. They didn’t cost a cent and are very useful.”

From the archive · Full text
Reader shop tip

Tom Collins

Tom Collins, Aetna Engineering, Granada Hills, Calif.

Tom’s company sells what may be the only digital replacement tachometer on the market.

“Because it’s solid state there are no mechanical parts. It’s guaranteed accurate to 1 rpm for the 20-year life of the unit,” Collins says.

“The units are so rugged they’ll even stand up to immersion in 6 ft. of water. We’ve been selling a lot for agricultural applications, such as fertilizer rigs where it’s important to maintain a constant ground speed to ensure exact application rates.”

The unit fits standard 3 3/8 in. dia. tach ports. (If the engine didn’t have a tach originally, they can be mounted in a hole wherever you choose, or with an optional mounting cup on top of the dash). They’re suitable for all 4, 6 and 8-cyl. gas engines and can be adapted to diesels with an optional sender ($48.75). Installs easily simply by connecting it up to three existing wires.

Sells for $197.50 plus $4.75 S&H. Contact: FARM SHOW Followup, Aetna Engineering, 17731 Candia Court, Granada Hills, Calif. 91344 (ph 800 776-7962 or 818 831-0607).

From the archive · Full text
Reader shop tip

Chuck Woods

Chuck Woods, CW Engineered Prod- ucts, Libby, Mont.

“If you normally throw away cutting tips for your oxy-fuel torch because the copper seating rings are damaged, you’ll like my new tool. It accurately refaces the bad rings to return the tip to safe, useable condition in minutes, saving you a lot of time and money.

“Designed for all Victor series cutting tips, ‘Neet Seet’ tool consists of a 7/8-in. dia. by 7/8-in. long solid piece of steel bored to a specific angle that exactly fits the angle of the tip seat. The inside of the tool is uniformly coated with a permanently bonded diamond abrasive to make it virtually indestructible and self-cleaning.

“To use, insert the tool into the cutting tip seating and turn it on the tip seats using firm pressure. Repeat until the seats are clean.

“Refaced seat rings ensure against back-flash and fire around the nut that are hazardous and can be caused by something as in-significant as rattling around in a tool box.”

Sells for $24.75, including S&H. Contact: FARM SHOW Followup, CW Engineered Products, P.O. Box 681, Libby, Mont. 59923 (ph 406 293-6712; fax 9014).

From the archive · Full text
Reader shop tip

Al Stober

Al Stober, Ledminster, Ma.

“To remove a seized bolt, drill a hole in the center of it. Then tap out the hole with a left-handed thread and insert a left-handed bolt. As you tighten the left-handed bolt, you’ll also loosen and turn out the seized bolt.”

From the archive · Full text
Reader shop tip

Glen Teel

Glen Teel, Hays, Kan.

“When the clutch slave cylinder on my 1985 Chevy S-10 began leaking, I found out Chevrolet wanted more than $90 for a kit to repair it.

“I found a much cheaper and easier fix than Chevy’s. I removed the plunger from the cylinder and saw that the rubber seal around it was bad. So I looked in one of the O-ring kits I had around the farm, found one that fit snugly over the seal, and then simply replaced the plunger.

“I made this repair six or eight months ago and the cylinder hasn’t leaked since.”

From the archive · Full text
Reader shop tip

W. Lyle Bentley

W. Lyle Bentley, Oakland, Iowa

“My son and I made this rack to organize our welding scrap iron. We used to store it all in a pile underneath our welding table. Not only was that a nuisance to step over all the time, but you never knew for sure what length iron you were going to pull out of the pile.

“We got a bunch of thin walled tubing for free from our local sprinkler company. We welded 26 different lengths of tubing together, starting with four 4-in. lengths on top down to four 24-in. lengths on bottom. (Lengths in between are graduated in 4 in. increments). The rack also stands on two 24-in. lengths of tubing welded at 90 degree angles to the others.

“We also welded ten 18-in. lengths of 6 in. tubing together vertically to make a free-standing rack that goes alongside the other one. We use it to hold pieces of scrap iron that are longer than 24 in.”

Shop feature stories

From the archive · Full text
Feature story

Speed Ratchet Works Like A Power Tool But There’s No Battery To Charge

Featured source:

“I made it because I was tired of using conventional ratchets that would stop turning once the nut or bolt was loose. My Speed Ratchet makes four complete turns with every squeeze of the handle until the nut or bolt is off,” says Gary Smith, inventor of the Speed Ratchet.

Smith says the Speed Ratchet is almost as fast and convenient to use as a powered wrench but you don’t have to worry about keeping batteries charged or keeping an air compressor nearby.

A reversing switch makes it easy to change directions with your thumb. The tool can be fitted with sockets, screw driver bits, torx bits or any other add-on tool. For stationary work, it could also be fitted with a foot-operated lever that attaches to the hand model by flex cable.

Many marketers are interested in selling the idea but he has yet to work out a deal with a manufacturer to produce the patented tool.

You can read more about the tool on the internet at www.inventing.com/ratchet.htm or contact: FARM SHOW Followup, Gary A. Smith, 110 Oakcliff Dr., Laguna Niguel, Calif. 92677 (ph 949 249-9953; E-mail: [email protected]).

From the archive · Full text
Feature story

Pto-Driven Generator Mounts On Tractor 3-Pt. With Welder

Featured source:

“It’s a handy combination that’s easy to move around,” says Merle Black, Valencia, Pa., who bolted a 10,000-watt generator and a stick welder onto a steel platform that mounts on his tractor’s 3-pt. hitch. The welder simply plugs into the generator.

He used steel pipe and angle iron to make a frame that fits the 3-pt. hitch arms. There are skids made from pipe under the platform that hold it above ground an inch or so.

Contact: FARM SHOW Followup, Merle W. Black, 311 Leslie Rd., Valencia, Pa. 16059 (ph 724 898-2609).

From the archive · Full text
Feature story

Roller Chain Repairs Made Easy

Featured source:

Counting, splitting and handling bulk roller chain is a lot easier with the “Chain Master” from Gerry’s Welding and Fabrication, Inc., Vienna, IA. The Chain Master contains an electronic counter, holding vise, and display stand. The self-powered electronic counter counts the number of pitches of 40, 41, 50, 60 and 80 single, double, triple, and extended pitch roller chain. Making a new chain is easy. You first use the Chain Master to count the number of pitches on an old chain (or use the number from a parts book) and then reproduce what you need off a bulk roll.

“Buying bulk chain saves money and the simple double vise on this unit holds the chain in place on either side of the chain splitter at a comfortable working height,” says Cory Westhoff of Gerry’s Welding.

“It’s a great new way to display, count and break roller chain. It actually counts the pitches of chain - new or used. You can use it to count the pitches on a piece of old, stretched chain to find what size chain you actually need to replace it.” Standard chain breaking tools can be used but a new chain breaker that pushes the pin all the way through without bending side links is also available. The easy-loading bulk display stand has eight swing-out bars that hold multiple reels of roller chain. The top of the stand holds tools, bins for links, or boxes of chain. The Chain Master sells for $843.75. A table model without the display stand is also available. The Counter, vise and display stands can also be purchased separately. Contact: FARM SHOW Follow-up, Gerry’s Welding & Fabrication, Inc., P.O. Box 37, New Vienna, Iowa 52065 (ph 800 624-7554; fax 319 921-2108).