Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 49, No. 2 (2025)

Vol. 49, No. 2 (2025)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 32–35

42 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip 1 of 3

Tommy Sanson

Individual tip 1 of 3 from this reader’s published contribution.
Tommy Sanson, Red Wing, Minn.

“To get more life out of your old diesel, use engine oil mixed with new diesel, one quart to 10 gal.

From the archive · Full text
Reader shop tip 2 of 3

Tommy Sanson

Individual tip 2 of 3 from this reader’s published contribution.
Tommy Sanson, Red Wing, Minn.

“Use J-B Weld to repair threads and bad bearing shafts. Cut, resize and then turn down or sand down the shaft so the bearing fits tight.

From the archive · Full text
Reader shop tip 3 of 3

Tommy Sanson

Individual tip 3 of 3 from this reader’s published contribution.
Tommy Sanson, Red Wing, Minn.

“If you have a dirt floor, set a board on jacks to store batteries to protect them from the ground.”

From the archive · Full text
Reader shop tip

Dave Krell

Dave Krell, Kennewick, Wash.

“Regarding Husqvarna mowers/small engines: Don’t leave gasoline in small engines over the winter. Start them up, then drain the gas tank with a turkey baster after shutting the engine off. Then start them again and let them run out of gas. Having a dry carburetor will ensure a reliable start in the spring.”

From the archive · Full text
Reader shop tip

Erik Hewitt

Erik Hewitt, Hillsville, Va.

“In the past, when I would take my Deere 970 out to do some work, I always felt I should carry some chains. I would put them in a toolbox that rested behind my seat. When I needed a chain, I had to climb off the tractor and up the rear to reach my chains. I created a time and back saver by bolting two steel ammo boxes to the back of the bucket. Now, my chains are always with me, easily accessible and ready at hand.”

From the archive · Full text
Reader shop tip

Greg Krush

Greg Krush, Hotchkiss, Colo.

“When I moved my farm 300 miles, I used apple bins to move my shop with a forklift on each end. I didn’t have to pack tools, cylinders, etc. I just put them in apple bins and strapped them onto the trailer. You could also use totes if you cut the tops off.”

From the archive · Full text
Reader shop tip 1 of 2

Alan “Lindy” Linda

Individual tip 1 of 2 from this reader’s published contribution.
Alan “Lindy” Linda, New York Mills, Minn.

“Tired of losing your chainsaw bar nuts out in the woods? Glue two small Alnico magnets to your saw. Lightly sand the backs of the magnets so the glue sticks better. Clean the glue surface well. I used hot glue.

From the archive · Full text
Reader shop tip 2 of 2

Alan “Lindy” Linda

Individual tip 2 of 2 from this reader’s published contribution.
Alan “Lindy” Linda, New York Mills, Minn.

“There’s often unused room under a shelf. Bend a piece of scrap metal for a custom-fit storage space.”

From the archive · Full text
Reader shop tip

Bruce Madden

Bruce Madden, Castleberry, Ala.

“I’m one of the many farmers that can’t back a four-wheeled wagon. I welded a 6-in. metal hitch on the front of my Polaris, and now I can drive it back under the shed.”

From the archive · Full text
Reader shop tip

Quinton Tschetter

Quinton Tschetter, Oskaloosa, Iowa

“Most of the things in my shop are on wheels so I can move them around as needed to make room for projects. However, some have only two wheels and can be quite heavy to pick up and move. I built a little mover to help. I just tip the top of the mover under the item’s edge and tip back to lift it off the floor.

“I built the mover out of some 1/2-in. pipe, some fittings, and a very short length of 1-in. aluminum channel for the lifter.

“The axle is 5/16-in. threaded (ready) rod inside a 4-in. length of pipe. A nut at either end of the pipe stabilizes the ready rod. Wheels from a Razor rider are mounted to the ends of the threaded rod. I used the Razor wheels because they have heavy-duty ball bearings.

“A 1/2-in. fitting welded to the top of the axle is the seat for the aluminum channel nipple. A 30-in. length of pipe welded to the axle at a 45-degree angle serves as a handle.

“I drilled and threaded the U-shaped lifter for a 5/16-in. bolt, which I drove into a short length of 1/2-in. pipe.

“To mount the lifter on the mover, I thread the pipe with the nipple into the fitting until it is almost tight. This lets the lifter pivot with the load when I turn the wheels.

“If I want a taller lifter, I use a longer length of pipe and bolt. I’m still experimenting with different materials for the top piece.”

From the archive · Full text
Reader shop tip 3 of 4

Preston Williams

Individual tip 3 of 4 from this reader’s published contribution.
Preston Williams, Victoria, Va.

“I welded a 6-in. by 1 1/2-in. piece of tubing to my loader bucket and hung my hay fork on it with a metal loop on the fork tip. I put it on or off easily.

“I never take the loader bucket off. It’s a big help.

From the archive · Full text
Reader shop tip 1 of 8

Kent MacDougal

Individual tip 1 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.

“Like many readers, FARM SHOW is my favorite publication. I’m glad to see I’m not the only one who braids baling twine. I built a cargo net with mine.

From the archive · Full text
Reader shop tip 6 of 8

Kent MacDougal

Individual tip 6 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.

“I found that a 2-in. eye bolt fastened to the hitch of my lawn tractor let me pull my utility trailer easily. I never bent it, even with the trailer loaded.

From the archive · Full text
Reader shop tip 8 of 8

Kent MacDougal

Individual tip 8 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.

“I beg everyone that uses old motor oil in their saws or as a stain to stop it. You can’t filter out dissolved solids. Burnt oil is carcinogenic. Dispose of it correctly.”

From the archive · Full text
Reader shop tip 1 of 3

Larry Wood

Individual tip 1 of 3 from this reader’s published contribution.
Larry Wood, Waldo, Ohio

“I had trouble lining up the hitch pin on my receiver. So, I welded a stop block on the top of my hitch. I first put the pin in and then welded a 1/4-in. steel block on the top. When I slide the hitch into the receiver, it now stops at the correct position.

From the archive · Full text
Reader shop tip 2 of 3

Larry Wood

Individual tip 2 of 3 from this reader’s published contribution.
Larry Wood, Waldo, Ohio

“I always carry my pintle hitch with me in my truck. But it was constantly sliding around in the truck bed. I came up with the idea of mounting it under the truck behind the bumper. I welded a square receiver over the top of my truck hitch frame. This stores my pintle hitch or any other hitch. I also drilled a 1/2-in. hole in the side of the receiver and welded a nut for a bolt. This bolt, when tightened, clamps the hitch in place.

From the archive · Full text
Reader shop tip 3 of 3

Larry Wood

Individual tip 3 of 3 from this reader’s published contribution.
Larry Wood, Waldo, Ohio

“I pick up lots of equipment with my skid steer forks, but I was always afraid that my lifting straps or chains would slip off the end of my forks. I drilled a 1/2-in. hole near the end of my forks. Then, I made a U-shaped steel strap and welded a 1/2-in. bolt to the bottom of the strap. Now, I have no fear of the straps slipping off. I also welded a 1/2-in. nut to the fork frame to store the new brackets. Now, I always have them with me.”

Shop feature stories

From the archive · Full text
Feature story

Rolling Shop Chair Made For Comfort

Featured source: Frank Manjarres

The Kneel-It is an ergonomic low-work posture-support device for anyone who kneels for prolonged periods. It’s well-suited for shop work and is designed to relieve strain and decrease knee injuries.

“My background is in aerospace; I was a Lead Engineer at Northrop Grumman in San Diego for 14 years before developing Kneel-It,” says Frank Manjarres, founder of Smart Design Products, Inc.

“I’ve always been a driven person, always looking to learn new skills. I’m a do-it-yourself type, and my wife took it upon herself to add flooring to my skills. Little did I know that it would test my body’s pain threshold.”

Put another way, Manjarres invented the Kneel-It through necessity.

“After about 100 sq. ft. into learning this new skill, the pain became too much,” he says.

“I explored options for a low posture work support device. In my mind, this was just a matter of searching and placing my order for a kneeling cart. But I quickly realized options were limited.” This led Manjarres to create a solution.

“It became my mission to make sure that the folks with these low posture work tasks like plumbers, electricians, painters, mechanics, shelve stockers, autobody workers, and more had a product that would truly be a solution to their very real pain. That’s when I decided to develop Kneel-It.

“It’s built with spring-loaded knee pads that pivot. This gives our customers maximum comfort by adjusting to their unique body structures,” he says.

“Plus, Kneel-It’s compact and easy to use, and the hardware can be replaced quickly, 100 percent tool-free.”

The sturdy construction can support up to 250 lbs., and the compact design allows for easy storage and transport. It’s made from cold-rolled steel, fiberglass-reinforced nylon, PP foam and stainless steel. Built-in cushioned knee pads add comfort, and the 360-degree turning capability improves functionality. Interchangeable attachments allow for more comfort, while the included roller mounts increase mobility while protecting floors.

Customer reviews show that Kneel-It makes sense for anyone who does a lot of interior finish work, including flooring, baseboard work or painting. A clean working surface works best, so outdoor projects might take more planning. Many agreed that the Kneel-It’s price was well worth it for the lack of pain they felt at the end of the day.

Now in its third version, the Kneel-It has added rotatable casters to switch between a braking and rolling configuration, as well as an upgraded quick pin seat attachment method. There’s also an upgraded finger latch for easy seat removal and a new color scheme.

Purchase the Kneel-It on the company website for $320.

“Our bodies have a shelf life,” Manjarres says.

“We should take every measure to protect them because we are worth it.”

Contact: FARM SHOW Followup, Frank Manjarres, Smart Design Products, Inc. (ph 520-390-5007; [email protected]; www.kneelit.com).

From the archive · Full text
Feature story

Fast And Easy Ratchet Tie-Downs

Featured source: Keeper Products, Foothill Ranch, Calif.

Unlike traditional ratchet straps, KwikFeed straps are designed with a unique ratchet mechanism that allows for quicker tightening and release. This can save time, whether hauling hay, securing equipment on a trailer, or keeping materials organized on the go.

In addition to hauling and transport, the straps are also suitable for keeping tools, hoses and other items stored and organized. They can help reduce clutter in barns, sheds and vehicles.

The groove in the drum makes these straps unique. Rather than pulling the strap all the way through, you can just feed it into the slot from the side.

The 1-in. by 12-ft. tie-down is a general-purpose strap with a 500 lb. working load limit and a 1,500 lb. break strength.

Another option is a 1 1/4-in. by 16-ft. tie-down marketed as professional grade and has a 1,000 lb. working load limit with a 3,000 lb. break strength. It has a patented forged steel drum.

The Extreme Edge versions offer 30 percent more wear-resistant webbing and an oversized, non-slip handle.

They also offer a 2-in. by 27-ft. heavy-duty commercial-grade tie-down with a 3,333 lb. working load limit and a 10,000 lb. break strength, exceeding DOT requirements.

The straps have earned good reviews from customers online.

“These straps are a lifesaver. I use them to secure my hay bales and equipment, and they save me time compared to regular straps,” says Ben M., a rancher from Texas.

Starting at $16, the KwikFeed ratchet tie-down straps can be purchased at Home Depot stores nationwide.

Contact: FARM SHOW Followup, Keeper Products, 50 Icon, Foothill Ranch, Calif. 92610 (ph 800-562-5625; www.keeperproducts.com).

From the archive · Full text
Feature story

No-Compressor Handheld Sand Blaster

Featured source: Koen Meukens, Antwerp, Belgium

The handheld BLSTRsander removes paint, rust and more from wood, metal, glass and brick, no matter how complex the surface. Unfortunately, it’s not yet available in North America. The corded, no-compressor sandblaster solved a common problem faced by anyone renovating an old building.

In 2014, Koen Meukens bought an old house in Antwerp, Belgium, and began sanding wood surfaces. The flat parts were easy, but sculpted parts, corners and curves frustrated him.

When he couldn’t find a machine to do the job, he developed a concept of what he needed. He brought the idea to life with the help of a mechanical engineer at the University of Antwerp and two graduate students.

In 2018, Meukens started GenR8BV to patent the concept and develop the prototypes. In 2024, he launched a Kickstarter program to do a test launch. By August 1, 725 backers had pledged $194,026, more than triple Meukens’ goal. The first 500 paid only $267 for the device, now retailing for $414.

“The funds allowed us to pay for tooling, factory setup and the first production,” says Meukens.

The cost is due to abrasion-resistant ceramic components designed specifically for the BLSTRsander. The output is described as similar to a compressor rated at 26 gal. at 145 psi (100 liters and 10 bar) with a blast gun. A high-speed wheel creates the pressure. Blasting medium gravity feeds into the airflow from the abrasives container. Equipped with a laser pointer, the handgrip, with its protective shield, directs the flow to the target.

The blast is wider, with a larger target area than a conventional compressor-powered blaster. However, that means no deep spots and smoother results.

While the device can use various grits, 0.2 to 0.5-mm grit and Metabo grit aluminum oxide are recommended for beginners. Although the product claims to be low-maintenance, thicker grain grit can cause blocking and require cleaning.

“For the moment, the BLSTRsander is only available in the European Union but will soon be introduced in the United Kingdom,” says Meukens.

“We hope to launch in the U.S. and Canada eventually. However, no 120-volt machines are available yet, or planned.”

Contact: FARM SHOW Followup, BLSTRsander ([email protected]; www.blstrsander.com).

From the archive · Full text
Feature story

Ladder Works In Shop And Field

Featured source: Little Giant Ladder Systems, Springville, Utah

The Little Giant Conquest ladder is a new multi-position ladder with added features aimed at helping you get work done.

Little Giant ladders are known for their grip and twist lock, allowing the rails to easily adjust to the desired size.

The integrated tip and glide wheels enable the ladder to move easily from job to job. The extension side of the ladder is narrow enough to access tight spaces and can be safely set up on poles or outside corners. The wall pad feet are designed for use on inside corners and flat walls without damaging the surface. The V-bar leans on poles, corners and walls.

Optional leveling outriggers keep the ladder stable on uneven terrain. A weight-balanced carrying handle makes transport easy.

The fiberglass Conquest ladder meets or exceeds all OSHA and ANSI standards. It’s rated Type IA to hold 300 lbs. and is available in 17 ft. and 22 ft. sizes.

Prices start online at $500 plus shipping for the 17-ft. standard model and go up to $700 for the 22-ft. all-terrain model.

It’s available from Little Giant, Fastenal and other select retailers. The ladders come with a limited lifetime warranty.

While not cheap, this ladder may fit the bill for those who want a versatile one with handy features that can be used in the shop and field.

Contact: FARM SHOW Followup, Little Giant Ladder Systems, 1198 Spring Creek Pl., Springville, Utah 84663 (ph 800-453-1192; [email protected]; www.littlegiantladders.com).

From the archive · Full text
Feature story

Changing Hydraulic Filters The No Mess Way

Featured source: Oscar Scott, Perryton, Texas

Unscrew a hydraulic oil filter, and if you just lose a few gallons of oil, you’re lucky. Oscar Scott wasn’t, so he figured out how to eliminate oil loss and the mess that often comes with it. His solution was a device he calls the Vac Trac. It worked well, so he formed a company to sell it, all because he made a mess on his shop floor and himself.

“The manual on my new Kubota said to change the filter at 400 hrs. and change the hydraulic oil at 1,000,” recalls Scott.

“I unscrewed the filter and got drenched in oil. My wife wouldn’t even let me in the house in those clothes.”

Determined not to make that mistake twice, Scott discussed the issue with his Kubota techs. They insisted that setting a 5-gal. bucket under the filter with him on his back was the only way to do the job, but he had to be quick. At 80, he had no interest in lying on his back on the shop floor and assured them he was not that fast.

“John David Shannon, manager of James Brother Implement in Amarillo, Texas, suggested I use a shop vac,” says Scott.

“He explained that attaching it to the gearbox inlet would produce a vacuum to hold the oil in place when the filter was removed.”

While the idea seemed sound, Scott recognized that he would only need about 20 in. of negative pressure to hold the 5 to 6-in. oil depth in the reservoir. He was concerned that the high volume (120 in. of negative pressure) with the shop vac could damage seals and worse.

“Shop vacs are inconvenient, cumbersome and dangerous to use,” says Scott.

“A shop vac’s high-volume flow could create violent enough bubbles to result in an aerosol of hydraulic fluid that would not only foul the shop vac but potentially create a combustible mixture of hydrocarbons and air.”

“I developed the Vac Trac,” he says.

“It’s about the size of a flashlight, 9 1/2 in. long and about 2 1/4 in. in diameter. The battery can be recharged in about two hours via a USB cable.”

The Vac Trac produces 90 percent less vacuum than a conventional shop vac. It has a magnetic mounting ring for a tight, hands-free connection to easy-to-reach gearbox inlets. It comes with an extension tube for reaching less accessible inlets with magnets on the side of the device to attach it to nearby housings. Adapters that match it up with all tractor brands are included. It’s priced at $174.95.

“That first time I changed a filter on my tractor, it took an hour,” says Scott.

“I made a mess on the floor, lost a set of clothes and my religion a time or two. The second time, using the Vac Trac, I lost about three tablespoons of oil.”

Contact: FARM SHOW Followup, Red Dog Vac Trac, 13610 County Rd. U, Perryton, Texas 79070 (ph 512-714-5000; [email protected]; www.reddogvactrac.com).

From the archive · Full text
Feature story

New Electric Bandfile

Featured source: Milwaukee Tool, Brookfield, Wis.

The M12 Fuel 1/2-in. by 18-in. bandfile is the first cordless bandfile that delivers pneumatic performance, size and features for professional automotive, industrial and metalworking users.

It uses brushless technology to deliver the fastest spot weld removal. The cordless bandfile has two speed settings, forward and reverse, a lock-on button and a variable speed trigger.

The bandfile has a tool-free 360-degree arm rotation, providing greater mobility and access. With the M12 XC4.0 battery, this product can remove up to 50 spot welds per charge.

“Just as good as my expensive pneumatic bandfiles but way more mobile. Plus, I never thought I would see one of these with reverse,” says Clint, a user on the Milwaukee website. This tool has a 96% positive rating online.

Priced at $249, it’s available from most tool retailers that sell a full line of Milwaukee products. We found that a battery came with purchase on some and others did not. Shipping varies by retailer.

Contact: FARM SHOW Followup, Milwaukee Tool, 13135 W. Lisbon Rd., Brookfield, Wis. 53005 (ph 800-729-3878; www.milwaukeetool.com).

From the archive · Full text
Feature story

Front-Mount Hitches And Drives Offer Options

Featured source: John Else, Cedar Falls, Iowa

Laforge LLC began its product line of after-market front-mounted hitches and PTO drives due to a need by some of the larger tractor manufacturers decades ago.

“There was a need back then, but a big part of our goal was to increase the capability of the tractor to run additional equipment,” says Laforge North American Distribution Manager John Else.

“This led to more forward-thinking and a large array of aftermarket solutions.”

The company offers front-mounted hitches and PTOs, which most buyers use to power snowblowers, mowers, generators or other PTO-powered machines.

Else explains that their 540 and 1,000-rpm PTOs are run by three different gearboxes, with models turning counterclockwise and clockwise. Most are gear-driven directly off the engine, except for the largest tractors.

They also build front hitch mounting systems and brackets for centered loads, offset loads, and intensive heavy-duty equipment. Applications can be raised or lowered for field work or transport. Available options include hydraulic receptors, connection kits, electrical harnesses, weight carriers and electronic controls.

Their PTOs and hitch mounts fit almost every tractor make and model, including Deere, New Holland, Case-IH, AGCO, Claas, Fendt and Massey Ferguson.

Laforge offers a factory installation option for all their products at the OEM dealership.

“It will ship to our facility before going to a dealer, and we complete it by working closely with the OEM dealership to meet all their requirements and standards. All our products and labor are factory warranty approved.”

The aftermarket hitches and PTOs are manufactured in France at the Laforge factory. Their Iowa-based facility works with hundreds of dealers across North America for purchasing and installations.

The front-mount hitches cost between $5,000 and $14,000, and the PTO with driveline alone costs between $6,000 and $9,000, depending on the tractor size, make and model.

“Our quality products and craftsmanship set us apart from our competitors,” Else says.

“Our heavy-duty systems are more robust.”

Contact: FARM SHOW Followup, La-Forge LLC, 1824 Lincoln St., Cedar Falls, Iowa 50613 (ph 855-408-3332; [email protected]; www.laforgegroup.com).

From the archive · Full text
Feature story

Extension Clamp Gets In Tight Spaces

Featured source: Tite-Reach, Orange City, Iowa

The Tite-Reach extension clamp is made for those tough-to-reach spots your hand can’t reach or may be too hot to touch.

The clamp is available in four sizes: Micro, Mini, Standard and Max. The Standard is 10 1/2 in. long, ideal for confined spaces. The Max extends up to 36 in., providing extra length for larger machinery or more challenging tasks. It’s designed to work with nuts and bolts ranging from 1/4 to 1 in.

Built from hardened alloy steel with a corrosion-resistant finish, the Tite-Reach Extension Clamp can handle repeated use in the shop or out in the field.

The extension clamp can save you time by allowing you to access tight spots without removing other equipment parts. Its vice-like design also ensures you won’t drop the part held until you loosen the tension nut. Unlike pliers, you don’t need to maintain tension to keep what you’re holding in place.

The tools start at $18, plus shipping. The company’s website sells a pack of three different sizes for $49 and offers free shipping on orders over $100.

“Just like its Tite-Reach ratchet extensions, these make the two-finger nut grasp, so hoping you don’t drop it is a thing of the past,” says user Paul Wisuri. Online reviews were overall positive, with 97% rating them at 4 or 5 out of 5 stars. People liked the ability to reach into tight spaces. One reviewer mentioned they wished it were built a bit more durable.

Contact: FARM SHOW Followup, Tite-Reach, 608 15th St. SE, Orange City, Iowa 51041 (ph 866-721-9399; [email protected]; www.tite-reach.com).

From the archive · Full text
Feature story

Portable Press Makes Drilling Easy

Featured source: Mike Glodosky, Salmon, Idaho

Mike Glodosky developed the Strong Arm 5 portable drill press after spending hours drilling at his job. He was tired of drilling holes by hand, finding that the drill would slip and slide around, and he also found it difficult to apply the force he needed on the holes.

He created the Strong Arm 5 to allow him to focus on a point as he drilled and made the pressure he applied greater with less effort.

It works horizontally or vertically and is useful overhead to prevent fatigue from holding the drill. Using leverage, it can reduce drilling time by up to 75%.

The Strong Arm 5 Mobile Drill Press works with corded, cordless and rotary hammer drills with a 1/2-in. drill chuck. The Total Sync Connection, exclusive to the Strong Arm 5, is similar to inserting a drill bit into the chuck. Adjust the 360-degree handle to the left to manage torque and let it rest against your body. This adjustment is crucial for stabilizing the drill during use. The Strong Arm 5’s 19-in. handle is designed to help with torque.

The drill press can push and pull into drilling material, eliminating the need to get underneath the job.

Accessories offered are an extension pole for overhead work that offers leverage from below and a vacuum foot attachment that works on stainless steel, aluminum or any flat and smooth surface.

On their website, prices start at $399 with free shipping. The MAX commercial version, which offers 1,000 lbs. of drilling force, sells for $475. It’s made in the U.S.A. and has a 30-day money-back guarantee and a one-year warranty.

Contact: FARM SHOW Followup, GloTech, 430 Confederate Dr., Salmon, Idaho 83467 (ph 208-409-6820; [email protected]; www.strongarm5.com).

From the archive · Full text
Feature story

Tool Stand Keeps Tools Handy

Featured source: Edwin Egli, New Salem, N.D.

Edwin Egli of New Salem, N.D., built a shop stand for his air and electric tools.

“It took maybe a day,” he says.

“I used an old car wheel, pipe and rods. Basically, what was available in the junk pile.” He tends to move it around his shop to ensure his tools are within reach during a project.

“It’s pretty mobile, although heavy when loaded with tools, so I’ve got to be careful,” he says.

“The tire holds electrical cords and the tools that don’t fit on the stand. I like that it keeps everything within a small area, so my tools are handy.”

Contact: FARM SHOW Followup, Edwin Egli, 4825 County Rd. 139, New Salem, N.D. 58563 (ph 701-471-0720).

From the archive · Full text
Feature story

Oil Filter Coffee Mug

Featured source: ClutchGear, Frankenmuth, Mich.

Inspired by the classic oil filter design, the Clutch Gear mug is made of stainless steel and has double-wall vacuum insulation.

Made with BPA-free 18/8 stainless steel, the center cap on the lid threads on/off for easy cleaning. Its silicone handle provides comfort and grip. Mugs are dishwasher safe, but hand washing is highly recommended.

“When I first saw the mug, I thought it was a neat concept. Then I saw the orange one, and I had to have it! It matches the striping of my car perfectly! I took the mug and the car to a local Cars & Coffee and got a ton of questions about where I got the mug from. I’m thoroughly enjoying it,” says Lionel T.

It’s available online starting at $35 plus shipping and comes in various colors in 15 or 20 oz. versions. A tumbler is also available. Contact: FARM SHOW Followup, ClutchGear, Frankenmuth, Mich. (ph 877-725-8824; [email protected]; www.clutchgear.com).

From the archive · Full text
Feature story

Rugged Bumper For Ford Pickups

Featured source: Fab Fours Inc., Lancaster, S.C.

Fab Fours’ Elite Ranch Style Bumper is an American-made bumper designed to withstand the everyday conditions on a farm or ranch.

Built from heavy-duty steel at its Lancaster, S.C., facility, the bumpers can withstand impacts, heavy loads and tough terrain.

The Elite bumper is available in Full Guard, Pre-Runner Guard or No Guard options and can be customized with features such as a winch tray, D-ring mounts, a 2-in. receiver and lower guards.

Prices start at $1,920 plus shipping. Fab Fours’ Black Steel Elite Front Bumper fits Ford Super Duty trucks from 2008 and up. It can be purchased online or at authorized dealers across the country. Fab Fours also offers bumpers, guards and protectors for different vehicles online.

Customer reviews show that the bumper works well for those in rural settings. A farmer shared, “It’s held up great over the past year, even after plenty of wear and tear.” Another user mentioned, “It’s been useful for protecting my truck and makes it easier to get the job done.”

Bumpers come with a limited lifetime structural and a limited one-year finish warranty.

The bumpers can be purchased through select retailers or online. Shipping costs vary and can be shipped directly to a retailer for installation.

Contact: FARM SHOW Followup, Fab Fours Inc. 2213 Industrial Park Rd., Lancaster, S.C. 29720 (ph 866-385-1905; [email protected]; www.fabfours.com).

From the archive · Full text
Feature story

Easy-To-Customize Truck Bed Organizer

Featured source: Thomas Carton

The Tmat cargo management system is a collection of cargo blockers that divides truck beds into unique compartments fitted around your tools and equipment.

“Tmat got its start when we grew tired of struggling to keep our truck gear organized,” says Thomas Carton, company representative.

“Things always slid around; we knew there had to be a better way. So, we created a simple modular system that prevents cargo from shifting and keeps everything within reach. It’s quick to set up, rugged and built to make everyday work or hauling easier.”

Install Tmat between the wheel wells; the mat will easily slide across the truck bed and onto the tailgate for easier access.

“The modular design lets you customize your truck bed to match any task, and the slide-out feature saves you from climbing in and out all day,” says Carton.

“Tmat sets up in just 5 min., no tools needed. We wanted something that works as hard as we do, whether for work or adventure.”

Target customers are truck owners who want to protect their gear and truck beds while keeping everything organized and within reach.

“It’s perfect for anyone tired of climbing in and out of the truck bed all the time,” he says.

“We see a lot of interest from tradesmen, farmers and outdoor enthusiasts, especially folks who use Tonneau covers and need a solution that works seamlessly with them.” In his mind, the modular grid system sets Tmat apart.

“One of the best features is how it can slide out onto the tailgate, so you can grab things near the cab without having to climb in and out of the bed.”

The company offers different kits tailored to match specific truck bed lengths, ensuring a perfect fit for any truck with the same size bed. For example, Tmat’s universal short bed kit ($319.99) fits between the wheel wells of most short bed trucks between 5 ft. and 5 ft. 5 in. in length. Fully assembled, the mat measures up to 5 ft. 4in. long by 4 ft. 2 in. wide. Each kit includes 20 12-in. by 12-in. panels, 13 12-in. by 2-in. strips, two quick-fit blockers, two tight-fit blockers, and two adjustable blockers. Other size mats are available, varying in price and number of pieces, including 4 by 4 cargo organization systems for SUVs ($199.99) and slide-out mats for long beds measuring 8 ft. to 8 ft. 2 in. ($399.99).

The panels’ interlocking design allows them to be configured for almost any enclosed cargo space. A vehicle finder (www.tmat.com/collections/tmat-vehicle-kits) and an online calculator (www.tmat.com/collections/custom-builds) can help determine how many panels you need. You can verify the fit virtually by selecting your vehicle’s year, make, model and bed length.

Tmat also offers more than a dozen accessories that integrate seamlessly with the system for optimal personalization.

“We’re always working to add new accessories and improve the system,” Carton says.

Contact: FARM SHOW Followup, Tmat, Thomas Carton (ph 405-213-1436; [email protected]; www.tmat.com).