Eric Webster
“I made this tire band saw out of two spare car tires. An electric motor belt-drives a pair of pulleys that turn a shaft that rotates the bottom tire. The saw blade runs from one tire to the…
Read the complete tip →928 shop tips and stories · page 12 of 16, newest issues first.
“I made this tire band saw out of two spare car tires. An electric motor belt-drives a pair of pulleys that turn a shaft that rotates the bottom tire. The saw blade runs from one tire to the…
Read the complete tip →“My homemade 48-in. belt sander is operated by a 1 hp electric motor. I use it to make furniture. The belt is 6 in. wide. A pair of screws at each end of the unit are used to…
Read the complete tip →“I mount a roll of paper towels on hangers that attach to the frame on the underside of the trunk lid on my Buick Century car. That way I always have a towel handy to clean off my…
Read the complete tip →Roger Wessels, Fairbury, Ill., came up with an idea that makes it easier to start the engine on his 1983 Allis Chalmers 720 riding mower.
Read the complete story →www.pivotpins.com): “Our company offers a wide variety of non-threaded fasteners including clevis pins, detent clevis pins, lynch pins, wire lock pins, tab lock pins, detent ring pins, positive lock pins, pull pins, ball plung-ers, ring pins, bent arm…
Read the complete tip →“I used to be in the fencing business and helped put up fences on game farms. To make it easier to do the job, I came up with this ‘wire twister’ that’s powered by a standard DeWalt 18-volt…
Read the complete tip →“I also have trouble with the brake light staying on in this GMC. To solve the problem, I simply unhook the battery cable for a few minutes and then hook it up again. This allows the computer to…
Read the complete tip →www.dakotariggers.com): This company offers a wide variety of wire rope assemblies and also nylon tie-down straps for hauling big bales, etc. They also sell winch lines and overhead hoist cables for shops.
Read the complete tip →“I’ve had problems breaking axle bolts on my Case 1845 Uni-Loader. Replacing the bolts is tough because I can’t get my hand into the holes to install them. I called the dealer and was told to pull the…
Read the complete tip →The Nail Kicker® denailer by RECONNX, Inc., is a handheld, air-powered nail remover that works up to four times faster than pulling nails by hand. It doesn’t just pull nails out. It “kicks” them out from the bottom.
Read the complete story →“It’s lightweight and much easier to use than hydraulic lifts and can be built a lot cheaper,” says Bruce Graham, Tyler, Texas, about his air-powered shop hoist.
Read the complete story →Instead of climbing stairs to get up to the 8-ft. high upper deck in his shop, Harry Engeland bought and modified an “electric-powered” platform. The unit was originally designed to lift a project up 3 ft. so it…
Read the complete story →“I made a simple 6-terminal throw switch in order to raise and lower my truck-mounted snowplow blade. It allowed me to convert my 12-volt winch, which would only power up, to power down, also. The throw handle sides…
Read the complete tip →“I use a shopping cart to haul my wire feed welder and acetylene tank around my shop. The welder rests on a metal shelf, and the tank mounts on brackets that attach to the cart. I widened the…
Read the complete tip →“Plastic wire spools - available free for the taking from motor or transformer shops - provide a neat and safe way to hang water/air hoses, extension cords, etc. The spools can be screwed directly to a wall or…
Read the complete tip →“A retractable extension cord made from an old vacuum cleaner cord mechanism gives me 25 ft. of cord for a drill.”
Read the complete tip →“Here’s an easy way to put threads all the way through lengths of pipe or square tubing. Use a woodworker’s dowling jig to make a centered, true pilot hole. Drill a hole and insert a nut. Weld around…
Read the complete tip →Paul Begin was tired of hurting his hands when trying to dislodge stubborn nuts and bolts on older salvage equipment. He finally decided to make a big wrench that used a worm gear to loosen bolts even in…
Read the complete story →Put this new gadget on a power drill and you’ll be able to cut through sheet metal, vinyl, steel mesh, ductwork, automotive body panels and thin sheeting.
Read the complete story →“To charge more than one battery at a time I line up the batteries so that the positive posts are aligned, and then use a vise grip to clamp a wire to all the positive posts. The negative…
Read the complete tip →“In a recent issue of FARM SHOW someone complained that the disc brakes on their Super “M” and Super “MTA” tractors don’t last very long. Maybe this idea will help. Whenever you’re replacing the brakes on these tractors,…
Read the complete tip →“Years ago, I rescued one of those old-time, manually-operated tire changing machines from a service station that switched to using air-operated machines. It sits out of the way in a corner of my shop until it’s needed. I…
Read the complete tip →Need help with a welding problem? Or just want to connect with others who share your interest in sticking pieces of metal together? We went looking on-line for the best do-it-yourself welding sites.
Read the complete story →Bruce and Roger Elliott built a crusher for oil filters. It reduces filters right down to hockey puck size and pushes out any remaining oil into a catch basin below. They used a piece of box beam with…
Read the complete tip →Kevin uses a lot of temporary electric fence on his 175-head stock cow herd. Rolling the 17-gauge wire was always an unpleasant chore, until he developed a roller powered by his cordless electric drill. He welded washers and…
Read the complete tip →If something is easy to grease, it’s more likely to get greased. That’s what led to the development of this new hands-free, foot-operated grease gun that leaves your hands free to stretch and reach difficult grease points.
Read the complete story →“It works great and cost only about $200 to build,” says Rich DeVries, Forreston, Ill., about the sand blast cabinet he built out of a used 250-gal. fuel tank and scrap steel.
Read the complete story →George (Bing) Ribble converted a used power unit from a commercial car wash into a low-cost, portable pressure washer. When he needs hot water to wash, he hooks it up to a 40-gal. gas water heater that stands…
Read the complete story →After Brad Noth bought a Hypertherm 1000 plasma cutter, he decided he needed a better cutting table and ventilation system.
Read the complete story →“The top of our Lincoln MIG welder was always cluttered with tools, gloves, helmets, and so forth, making it impossible to raise the side panels and get into the welder to change wire spools.
Read the complete tip →Gord Stein of Barrhead, Alberta, is a bit of a “neat freak” in his farm shop. He says keeping everything organized and easily accessible helps him get his work done faster and more easily. One of his best…
Read the complete story →www.agstapletech.com): This company makes a lightweight fencing tool that holds up to 48 steel fence staples at a time in a cartridge. The tool is equipped with a spring-loaded plunger and is designed to be positioned over the…
Read the complete tip →“I save time by having special purpose tool boxes for electrical, plumbing, brakes, small engines, tires, wood working, etc. There’s some duplication of tools between boxes but it’s a lot easier than trying to pick all the necessary…
Read the complete tip →“In a recent FARM SHOW issue there was an article on problems with Super ‘M’ and Super ‘MTA’ disc brakes. The problem was they didn’t last very long. Maybe this will help. When re-pairing brakes, be sure to…
Read the complete tip →Robert Green doesn’t need a tower for his horizontal windmill. He doesn’t need a bunch of gears or blades. He doesn’t even need much wind.
Read the complete story →Jesse’s a diesel technology student at Lake Area Technical Institute, Watertown, S. Dak. He and Steve Peters, a diesel instructor, came up with an inexpensive way to recharge 90-amp Nippondenso alternators commonly found on Deere tractors.
Read the complete tip →Is your garden tractor engine shot? A new engine from the manufacturer will cost a bundle, if it’s available. Rebuilding an engine isn’t cheap either, unless you can do it yourself. Tim Padgett, at the Small Engine Warehouse,…
Read the complete story →Having trouble finding parts for an old pickup or car? Restoration Specialties and Supply, Inc., Windber, Penn., may have just what you’ve been looking for.
Read the complete story →Neil Ohler’s Ford Jubilee (9 NNA) tractor is 50 years old this year and still going strong. But Ohler nearly had to retire it for lack of a regulator.
Read the complete story →“Several acquaintenances of mine have had problems with the front-mounted coil burning out on their Ford 9N tractors, probably as the result of switching the tractor’s charging system from 6 to 12 volts. I had the same problem…
Read the complete tip →“This simple device comes in handy to re-pair wire fences. It makes a neat splice. It consists of a metal strip that’s 1 in. wide and 1/8 in. thick. One end is cut narrow and is bent into…
Read the complete tip →“I also converted an old gas grill that didn’t work any more into a portable parts washer, by replacing the grill with a 3-gal. electric-operated parts washer. I use the grill’s folding front and end sections to hold…
Read the complete tip →“I made a portable battery charger using a 2 1/2 hp Briggs & Stratton gas engine to belt-drive an automotive alternator. Both the engine and alternator mount on the frame of a push-type, 3-wheeled lawn edger.
Read the complete tip →“When I bought a used Ford 9N tractor, it was equipped with a pto-driven hydraulic pump. I wanted the tractor to have two hydraulic systems so I installed a power steering pump that’s belt-driven off the tractor’s alternator.…
Read the complete tip →“I made my own wood burning stove and mounted a heat exchanger inside the stove pipe. I use it to heat my 32 by 28-ft. shop building which has an 11-ft. high ceiling, as well as a 12-ft.…
Read the complete tip →If the performance of the brakes in your pickup, SUV, or car is not what you’d like, you might want to take a look at the idea of using cross-drilled - or slotted - rotors.
Read the complete story →“I had problems in my small shop area with dust. To solve the problem, I built a cover for my bench grinder that goes around the entire grinder except for on front. There’s enough room for me to…
Read the complete tip →“Here’s an idea I use to store drop cords, hoses or anything else that can be coiled up. It takes up very little space. On a post or wall, drive nails every 8 or 10 inches vertically. Make…
Read the complete tip →Anyone who has ever tried to tach weld a nipple fitting onto a steel pipe or tank knows it can be tricky. You have to hold the fitting with one hand and at the same time tach weld…
Read the complete story →He converted his acetylene welder to a propane model by removing the original oxygen tank and replacing it with a 20-lb. barbeque grill-sized propane bottle that he already had.
Read the complete tip →You can lower your shop heating bills with this new shop divider curtain from Rainbow Industries, Inc., S. Vienna, Ohio.
Read the complete story →“My Deere 435 round baler has dual twine tie arms which allow it to wrap two lines of twine at the same time. It uses a pair of twine ‘brakes’ which hold tension on the baler twine as…
Read the complete tip →“Our battery charger is very easy to drag all over the farm since we mounted it on an old golf bag cart. Golf carts are designed to roll easily over uneven ground, which makes them perfect for farm…
Read the complete tip →“While cleaning up after an ice storm, I came up with an easy way to splice broken fence wire. I stretch the wires so they overlap about 1 1/2 in. and then bend up about a 3/4-in. long…
Read the complete tip →No matter how long a lead-acid battery has been in or out of service, this new battery conditioner can extend its life, says IES, Innovative Energy Systems.
Read the complete story →While Michael Mortell was replacing the bolts that hold the shanks on his IH 4600 field cultivator recently, he figured he could eliminate that chore in the future if he could just figure out a way to lubricate…
Read the complete story →After our story in the last issue on West Coast Inventor Supply, a company that specializes in miniature parts for inventors and engineers (ph 949 858-7251), we heard from Bob Stevens at Small Parts Inc., a company based…
Read the complete story →“My Deere 435 round baler has dual twine tie arms which allow it to wrap two lines of twine at the same time. It uses a pair of twine ‘brakes’ which hold tension on the baler twine as…
Read the complete tip →“Often when drilling big holes on a drill press, even at the slowest speeds, it was too fast and I was always burning out bits. I decided there had to be a way to slow the drill down…
Read the complete story →“A lot of equipment today has small wheels on narrow hubs with bearings and thin metal or plastic caps over the hub.
Read the complete tip →