From the archive · Full text
Reader shop tip
Rodman & Co., Inc., 2823 N. San Fernando Blvd., Burbank, Calif. 91504 (ph 800 228-1806 or 818 846-9494; fax 9681)
“Our new ‘Nibbler’ sheet metal cutting head fits any electric, pneumatic or cordless drill with a speed range of 1,500 to 3,000 rpm’s. It cuts steel, brass, copper, aluminum, plastic, and fiberglass with no distortion, jagged edges, or…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Richard Cox, Jacksonville, Ill.
The two men also came up with a handy high-speed sander-buffer for polishing steel shafts and also for rounding wood. It’s a high-speed emery blade mounted on an electric motor, mounted parallel to a small work table. They…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Miller, Spencer, Wis.
“I bought a Delta 14-in. chop saw which lasted less than 2 years before the motor burned out. I then rebuilt the saw at about 3/4 the cost of new only to have it burn out again 2…
Read the complete tip →From the archive · Full text
Reader shop tip
LeRoy C. Mack, Manistique, Mich.
“When a tie rod end came apart on our Ford 7000 tractor, I found that the nylon bushing was shot. A new end would have cost $60. I cleaned everything out and replaced the O-ring with a loop…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Mike Ruppert, Wapakoneta, Ohio
“An idea I had in my shop was hanging some old school lockers on the wall, horizontally, three-high. They’re excellent for power tools, cords, and other miscellaneous equipment or parts.”
Read the complete tip →From the archive · Full text
Reader shop tip
Perry Hathaway, Claypool, Ind.
“To hook a battery charger up to a 600 Bobcat, I put an extension onto the positive cable so I don’t have to take the seat off to charge it.”
Read the complete tip →From the archive · Full text
Reader shop tip
Alan Maclean, Kingston, Ontario
“I modified my shop hydraulic press, which is equipped with a 5,000 lb. hand pump. Cylinder movement was slow. I installed a ‘T’ at the cylinder inlet and supplied oil to the ‘T’ with a small electric hydraulic…
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky.
“Here’s a photo that shows how I solved the problem of carrying tools and miscellaneous supplies on my Cub Cadet riding mower. I bolted a surplus ammunition box on the deck of the mower. I carry tools, tie…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Dale Spoerl, Elizabeth, Ill.
“The battery on my Farmall 1026 tractor was originally located under the cab where it was difficult to reach. It extended half way into the cab and I couldn’t get at it unless I opened both front windows.…
Read the complete tip →From the archive · Full text
Reader shop tip
Barry Diffenderfer, Manheim, Penn.
“When replacing a hose or wire on a piece of equipment, especially if it’s long or hard to get to, attach a piece of wire to the one end before pulling the old hose out. This makes it…
Read the complete tip →From the archive · Full text
Reader shop tip
Landis Zimmerman, Zimmerman Oliver-Cletrac, 1450 Diamond Station Rd., Ephrata, Penn. 17522 (ph 717 738- 2573)
“We specialize in parts and service for Oliver-Cletrac crawler tractors, featuring new, used and rebuilt parts. We have most of the mechanical parts available for the following models: HG, OC-3, OC-4 & 46, and OC-6. Parts availability for…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
North Dakota farmer named Bob Heinzman is an inventor who runs a manufacturing plant, along with his brother. Years ago FARM SHOW featured his mini-tree spade for transplanting large trees without the need for a big truck (that…
Read the complete story →From the archive · Full text
Reader shop tip
Gary Lantz, Augusta, Ill.
“I came up with a way to automatically start and stop the auger at my bin when unloading grain that I haul in from the field during harvest. I connected a mercury switch to a pair of 12-volt…
Read the complete tip →From the archive · Full text
Reader shop tip
Howard Vogel, Waverly, Iowa
“After looking at various commercial chop saws, I reached three conclusions: They weren’t built heavy enough, they didn’t cut angles with the accuracy I required, and I couldn’t jus-tify the expense.
Read the complete tip →From the archive · Full text
Reader shop tip
Bruce Lowery, Spotsylvania, Va.
“If you’re fed up with tripping over extension cords in your shop, get several surface-mounted electrical boxes, install receptacles, and hang them from the ceiling in your shop at various locations high enough to clear your head. Then…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“We needed more floor and wall space in our shop so we mounted our air compressor up out of the way, 10 ft. off the floor,” says Ken Brecht, Moorcroft, Wyo., who built a heavy steel platform to…
Read the complete story →From the archive · Full text
Feature story
By By Mick Lane
Featured source:
If you’re tired of dirt and sparks in your face while working underneath pickups and cars, Accessible Systems, Inc, Jonesborough, Tenn., has a possible solution.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Barry Clohassey, Tignish, P.E.I.
“With good bench grinders selling for $75 to $150, I decided to build my own using a pair of 1/ 4 hp electric motors salvaged from old household appliances. I welded a 3 1/2-ft. length of 2-in. dia.…
Read the complete tip →From the archive · Full text
Reader shop tip
Curt N. Balmer, Newton, N.J.
“In re-gards to the owner of a 1998 GM pickup in your last issue who complained about not being able to turn off the auto-on headlights, here’s how to do it. Just a light tap on the emergency…
Read the complete tip →From the archive · Full text
Reader shop tip
Dakota Tools, Inc., Box 261, Orford, N.H. 03777 (ph 888 597-3624; fax 603 353- 4836)
“Our new Multi-Tip Driver allows you to drive any size socket with no need to stop when switching from 1/4, 3/8, or 1/2 in. One model fits in a standard drill chuck. And our ratchet adapter snaps onto…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Briggs, Massing, Id.
“I made a farm office out of a 20-ft. trailerhouse. I bought it cheap, moved in a desk, and plumbed in sewer, phone, water and heat. It’s a handy way to keep tech manuals, paperwork, and other records…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“The main drive belt on my sugar beet de-foliator costs about $400 so I came up with a simple belt slip monitor that tells me if there’s a problem before a belt gets ruined,” says Earl Riopelle, Argyle,…
Read the complete story →From the archive · Full text
Reader shop tip
Mike Graham, Edison, Ohio
“You can fix a loose head on any size wooden handled hammer using this simple, low-cost method.
Read the complete tip →From the archive · Full text
Reader shop tip
Barry Zellitti, Dao, Colo.
“I had trouble removing the battery from a 610 Bobcat loader. I solved the problem by notching the frame brace 1/2-in. deep along the length of the battery.”
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 4
Individual tip 4 of 4 from this reader’s published contribution.
Craig Froman, English, Ind.
“To check for spark on a gas engine - large or small - I hook an electric fence tester to the spark plug wire and ground the other end to the engine. Then crank the starter. The tester…
Read the complete tip →From the archive · Full text
Reader shop tip
Fred Galehouse, Doylestory, Ohio
“I came up with a handy way to put a connector link into roller chains. I tie a piece of string or cord to one link and then thread it back through a link on the other side…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Russ Wahl, Cut Bank, Mont.
“I also made a rolling shop light by putting caster wheels on the bottom of a steel wheel rim and then welding a vertical pipe to the top of the wheel. I put a light at the top…
Read the complete tip →From the archive · Full text
Reader shop tip
Tom Collins, Aetna Engineering, Granada Hills, Calif.
Tom’s company sells what may be the only digital replacement tachometer on the market.
Read the complete tip →From the archive · Full text
Reader shop tip
James Collins, Richfield Springs, N.Y.
“One of the handiest ideas I’ve had in my shop are my nut and washer holders made from wire coat hangers. What I do is reshape a hanger so it looks like a big safety pin, with a…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
If you do your own welding, you might want to call Lincoln Electric to get a copy of their free guide, “Stick Electrode Welding Guide: Procedures and Techniques”. Even if you’re experienced, you might learn something new from…
Read the complete story →From the archive · Full text
Reader shop tip
Arvin De Cook, Sully, Iowa
Arvin mounted a powerful 300-watt floodlight on rolling frame made from bike parts into order to have good light anywhere in his shop or farmyard.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
“I also use detergent bottles to carry oil and mixed gasoline for my chainsaw. I put a 50:1 mix of gas and oil into a larger red bottle and chain oil in a smaller blue bottle. Then I…
Read the complete tip →From the archive · Full text
Reader shop tip
Rick Mabeus, Winfield, Iowa
“I got tired of always untangling my extension cords so I came up with the idea of putting them in empty plastic buckets. I now have five different cords in buckets. They’re easy to carry around and it’s…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Casper, I-Con, Chagrin Falls, Ohio
Ron has been selling a “flameless welding” product to big grain companies for years. Abraso-Weld, or “metal in a can”, has been used by Cargill and others to make industrial-size repair jobs without requiring con-ventional welding.
Read the complete tip →From the archive · Full text
Reader shop tip
John Out, Enderby, B.C., Canada
“My 10-ft. 6-in. Deere 1360 rotary mower-condi-tioner is equipped with six cutting discs. Three of the discs rotate in one direction and the other three rotate in the opposite direction. When the discs wear out, I switch each…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
This new combo welder lets you do both stick welding and wire feed welding with one machine.
Read the complete story →From the archive · Full text
Reader shop tip 5 of 5
Individual tip 5 of 5 from this reader’s published contribution.
Craig Froman, English, Ind.
“You can make a paper towel holder for the shop or garage using a heavy wire coat hanger. Just cut one corner and make a couple of interlocking hooks. They also work well to hold rolls of tape,…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Cottonwood Welding’s new Black Max hydraulic press is built tough and comes in three models with 50, 100, and 125-ton capacities. The 50-ton model has a 12-in. cylinder stroke and a self-contained hydraulic system equipped with a 2-speed…
Read the complete story →From the archive · Full text
Feature story
Featured source:
The head on this rotating mitre band saw can be moved left or right up to 45 degrees, allowing you to switch to a different cutting angle in seconds, says Ellis Mfg., Verona, Wis.
Read the complete story →From the archive · Full text
Reader shop tip
Fred Mueller, Sheridan, Wyo.
You can make your own tow ropes, lead ropes, catch or show ropes, piggin’ strings and lariats with this old-style rope-maker that Fred re-cently brought back into production.
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Anyone with an older Cat crawler will want to take a look at this new converter that lets you mount an alternator in place of the gear-driven generator.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“We wanted an easy way to partition off part of our 50 by 50-ft. shop so we could wash or paint equipment without getting water or paint all over everything,” says John Imhoff, who, along with Dave and…
Read the complete story →From the archive · Full text
Reader shop tip
A. David Karge, Tallmadge, Ohio
“Many drill bits bigger than 1/2-in. dia. have a tendency to slip in the drill chuck. If you grind three flat sides onto the shank, you can solve the problem. You can space these equidistant around the shank…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Watt, Westlock, Alberta
Ron’s company, Hi-Tech Distributors, manufactures and sells a Swedish-designed injector flush system for diesel engines that uses a slightly different approach than other such systems on the market.
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky
This shut-off switch for stopping my table saw was quick and easy to make. It lets me shut off the saw without taking my hands off materials I’m holding. It consists of a 3 by 10-in. board, 1/…
Read the complete tip →From the archive · Full text
Reader shop tip
Keith P. Mayer, Naper, Neb.
“I own two GM 6.2-liter diesel-powered pickups that are reliable and burn considerably less fuel than pickups with comparable gas engines. However, GM’s starting aid system is a major problem. It relies on a ‘glow plug’ system that…
Read the complete tip →From the archive · Full text
Reader shop tip
John Tesch, Mervin, Sask.
“Here are the photos of my home-built, bench-mounted grinder and brush wheel (Vol. 22, No. 3, page 30). As the story explained, the electric motors from worn out pumps can be converted into shop bench grinders and cutters.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Doug Clark, Goderich, Ontario
“In Vol. 22, No. 1, Dan Petersen of Curtice, Ohio, asks for help to get the battery charging on his Massey-Ferguson 180 tractor. I assume that it’s wired correctly, has an old-style Delco alternator, and an external voltage…
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Dawson, Wheatley, Ontario
“I rigged up a buzzer that sounds whenever I turn off my Allis-Chalmers 185 diesel tractor but forget to remove the key. It has saved me from having a dead battery more than once. On older tractors like…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert J. Niederkorn, Chaffee, Mo.
Robert has a fabulous idea for disabled or inexperienced combine operators - foot operated header controls.
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Leonard Seltzer, Manhattan, Ill., made a low-cost portable light stand using a spare donut-type car tire as the base.
Read the complete story →From the archive · Full text
Feature story
Featured source:
You can take advantage of all the available space in your shop with this 2 or 3-story storage system that eliminates the need to build structural floors. It uses heavy rivet-style shelving that you assemble with a hammer.
Read the complete story →From the archive · Full text
Reader shop tip
Central Supply & Rubber Co., 109 North 9th St., Omaha, Neb. 68102 ph 800 444-8666
“You can jump start any vehicle without the need for jumper cables or another vehicle using our new Jump-N-Carry. The portable unit has its own battery and jumper cables and comes in a one-piece molded case. It provides…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Stephen, Martinsville, Ill.
He turned an old forklift mast into a heavy-duty shop elevator by mounting it along one wall and building a platform onto the mast in place of the forks. He uses it to ride up to the upper…
Read the complete tip →From the archive · Full text
Reader shop tip
John E. Tesch, Mervin, Sask.
John and his brother, Adolph, have converted electric motors from worn out pumps into shop bench grinders and cutters.
Read the complete tip →From the archive · Full text
Reader shop tip
Joyce Dulin, Cordova, Md.
Joyce and her husband, Bunky, operate Antique Gauges Inc., which handles custom-built replacement gauges (temperature, oil pressure, amperage, etc.) for tractors built between the 1930’s and ‘50’s. They’re exact reproductions of originals.
Read the complete tip →