Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 27, No. 5 (2003)

Vol. 27, No. 5 (2003)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

40 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Tom Billingsly

Tom Billingsly, Buckeye, Ariz

“Here’s an idea that a custom manure-hauling contractor came up with for his trucks with side-mounted gas tanks. He was working in extremely dusty, dirty conditions, hauling sludge onto cotton fields. The problem was that he had to keep changing fuel filters on the trucks because of sediment that would get into the fuel when refueling, or for other reasons. He told me he finally solved the problem by screwing a short length of pipe into the bottom of each gas tank. He simply put the pipe in the drain-out hole and put a cap on the pipe.”

What would happen is that as the diesel fuel sloshed around in the tank, sediment would settle down into the short piece of pipe. Every few days he would simply unscrew the cap and let a bit of fuel wash out onto the ground, clearing the sediment.

“It’s very simple and kept the fuel filters relatively clean. It gets the big stuff. Floating sediment still goes through the filter. The idea would work on any gas tank you can attach a pipe to.”

From the archive · Full text
Reader shop tip 1 of 2

Steve Spiering

Individual tip 1 of 2 from this reader’s published contribution.
Steve Spiering, 48594 Hwy. 158, Milbank, S. Dak. 57252 (ph 320 568-2246)

“The cable on my bin’s stirrator kept falling off. I had to put the cable back on up to four times a day, which got old. I solved the problem by welding on a shield off a rolling cultivator, which provides the pulley with a deeper flange. I started with a shield that matched the size of the pulley and cut off all the teeth. Then I welded the modified shield onto the pulley. The replacement flange deep-ened the pulley. Since I made this modification two years ago the cable hasn’t fallen off once.

From the archive · Full text
Reader shop tip 2 of 2

Steve Spiering

Individual tip 2 of 2 from this reader’s published contribution.
Steve Spiering, 48594 Hwy. 158, Milbank, S. Dak. 57252 (ph 320 568-2246)

“Our 7-in. dia., 55-ft. long, pto-driven grain auger wasn’t big enough to meet our needs any more, so I converted it to an electric-op-erated model to boost capacity. A 5 hp electric motor mounts on two lengths of 1 1/4-in. dia. steel tubing that attaches to the auger’s A-frame with four muffler clamps. The motor belt-drives the auger gearbox. If I want, I can use my tractor to pto-drive the auger again by loosening eight bolts on the clamps. The clamps can be slid up or down the frame in order to tighten or loosen the belts. The auger has a capacity of about 400 bu. per hour.”

From the archive · Full text
Reader shop tip

Max Serr

Max Serr, Paul, Idaho

“Here in Idaho we use a lot of 8 and 12-in. dia. underground pipe for irrigation. Eventually, the bottom side of the pipe rusts out. To fix it, you have to cut an entrance hole through the top side of the pipe and then go inside it and weld a steel plate over the rusted-out area. When that’s done you have to weld another plate over the entrance hole. Another way is to dig a very big hole under the pipe so that you can get underneath it and weld a plate onto the bottom side of the pipe. Either way, it’s a lot of work.

“I came up with an easier way by building my own giant pipe wrench. I use it to rotate 50-ft. long sections of pipe 180 degrees. Once the pipe has been rotated, I weld a plate on the bottom side of the pipe, and then I rotate the pipe back to its original position.

“I built the tool out of a 5-ft. long section of 1 1/2-in. (inside diameter) pipe, 4 ft. of no. 100 roller chain, and a 1/2-in. dia., 3-in. long metal hook. One end of the chain is welded to the pipe and loops back over the hook, which is also welded to the pipe.

“I think the same tool could be used on any object with a round surface.”

From the archive · Full text
Reader shop tip 1 of 2

Douglas V. Spencer

Individual tip 1 of 2 from this reader’s published contribution.
Douglas V. Spencer, Fenwick, W. Va.

“I couldn’t find any replacement grass seed tubes for my Massey Harris grain drill so I simply cut a cheap, plastic 1/2-in. dia. water hose to the proper length.

From the archive · Full text
Reader shop tip 2 of 2

Douglas V. Spencer

Individual tip 2 of 2 from this reader’s published contribution.
Douglas V. Spencer, Fenwick, W. Va.

“To keep a pencil handy at all times, I tape a clothes pin to the pencil and then clip it to the bill of my cap. The pencil is always there when I need it.”

From the archive · Full text
Reader shop tip 1 of 3

Vic Smith

Individual tip 1 of 3 from this reader’s published contribution.
Vic Smith, Parkville, Mo.

“While restoring my great grandfather’s old 2-row Ford planter, I found that some springs were old and rusted. To solve the problem I bought surplus spring kits at Tractor Supply. I treated some of the old and rusted plates with Speed Dip, a product that’s used to weatherproof traps.

From the archive · Full text
Reader shop tip 2 of 3

Vic Smith

Individual tip 2 of 3 from this reader’s published contribution.
Vic Smith, Parkville, Mo.

“Instead of buying expensive penetrating oil, I mix diesel fuel with baking soda. Works just as well.

From the archive · Full text
Reader shop tip 3 of 3

Vic Smith

Individual tip 3 of 3 from this reader’s published contribution.
Vic Smith, Parkville, Mo.

“I lined my shop walls with pegboard and mounted exhaust fans on them. The fans are hooked up to timers. They keep my shop well ventilated.”

From the archive · Full text
Reader shop tip

Karl Rosendahl

Karl Rosendahl, Spring Grove, Minn.

“I came up with a simple way to find the causes of shorts in a car, pickup or tractor. I solder a wire to each end of a blown fuse and then connect a headlight bulb to the wire. Then I plug the blown fuse into each fuse socket. The bulb will shine brightly if there’s a short in a circuit. Then I disconnect the load or connectors one at a time until the bulb either glows dim or goes out. Be sure to use headlight bulbs with the same voltage rating as the system you’re testing.”

From the archive · Full text
Reader shop tip 1 of 4

Elmer Pinkerton

Individual tip 1 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.

“There are several suggestions around on how to remove the nut that holds the blade on push lawn mowers. Forget them all. An air impact wrench will bring that nut off in seconds without anything holding the blade. Also, on a chain saw nut when the book tells you to block the piston with wood through the port holes - don’t do it. Use the impact wrench but first be sure to determine whether it’s a left or right handed nut.

From the archive · Full text
Reader shop tip 2 of 4

Elmer Pinkerton

Individual tip 2 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.

“One of your readers suggested using two nuts as a gauge to sharpen drill bits. Fine idea, but it’s easier to use crazy glue to weld the nuts into one gauge.

From the archive · Full text
Reader shop tip 4 of 4

Elmer Pinkerton

Individual tip 4 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.

“In a recent issue someone said he used a short length of pipe to protect tire valve stems from damage. I like this idea because you can safely leave a trailer in a hog lot without having to worry about flat tires.”

From the archive · Full text
Reader shop tip 1 of 2

Cary Urka

Individual tip 1 of 2 from this reader’s published contribution.
Cary Urka, Brethren, Mich.

“I built an inexpensive wood stove out of an old fuel barrel. I mounted the barrel on four metal legs, then cut a door into one end of the barrel and installed a baffle inside. A stovepipe chimney extends up to the building’s roof. I use my forklift to haul the stove outside the shop where I clean out the ashes. A fan blows down toward the stove to help spread the heat around. A furnace filter mounts on the back side of the fan and filters the air before it goes through the fan motor. I lined both sides of the stove with fire brick and also welded a couple of angle iron stiffeners lengthwise to both sides of the stove to keep the sides of the barrel from buckling. The stiffeners are spaced 6 in. apart and located just above the fire brick.

From the archive · Full text
Reader shop tip 2 of 2

Cary Urka

Individual tip 2 of 2 from this reader’s published contribution.
Cary Urka, Brethren, Mich.

“I wash all my equipment outside the shop using an Alcoa hot pressure washer that mounts inside my shop. The washer’s hose reel mounts about 3 ft. off the floor. I feed the hose out through a hole that I cut into the building wall and attach a wand to it. The washer’s on-off controls mount outside the building. Lets me wash equipment outside the building during the winter without ever having to open the door. The pressure washer is equipped with its own fuel burner to heat the water. The gas tank and fuel burner coil mount behind the pressure washer tank. I attached a big pipe to the tank to deliver the burner’s exhaust outside the building.”

From the archive · Full text
Reader shop tip

Donald Bunch

Donald Bunch, Bunch Farm Services, Inc., Box 712, Aberdeen, Miss. 39730 ph 662 369-9570

“I like the idea of using tire sealants, but I often find that it’s not easy to get the sealant into the tire. To solve the problem I made this little device. It consists of a 12-in. length of 2-in. dia. PVC pipe that’s threaded at one end. The flexible tube from an aerosol can of tire sealant is fitted on a hose barb that’s screwed into the cap. To use the device, I remove air from the mounted tire, then remove the cap with the valve stem in it and pour in the proper amount of tire sealant.

From the archive · Full text
Reader shop tip

Harvey Wasson

Harvey Wasson, Wasson’s Service, Perry, Mo.

“My hands don’t work as well as they used to, so when carrying heavy objects around my shop I simply wrap an old serpentine belt around the object. This idea works especially well on cylindrical gas tanks. It also works great for carrying metal or plastic pipe that’s wet or muddy because the belt won’t slip like my hands might. Ser-pentine belts can be found on most late model cars and trucks. I’ve used this idea for 10 years. Before serpentine belts came along I used conventional V-belts.”

From the archive · Full text
Reader shop tip

Bob Batteen

Bob Batteen, Box 401, Urbana, Iowa 52345

“In a recent issue of FARM SHOW someone complained that the disc brakes on their Super “M” and Super “MTA” tractors don’t last very long. Maybe this idea will help. Whenever you’re replacing the brakes on these tractors, be sure to clean all rust, etc. The reason is that the brake housing butts up against the brake drum, which butts up against the transmission housing. So make sure these surfaces are super clean. Then apply a thin coat of gasket maker to all the surfaces and reassemble everything. The brakes should be set according to instructions in the operator’s manual, and new boots should be installed. My Super “MTA” is a loader tractor and it sets outside all year long, yet the last time I installed new brakes was four years ago.”

From the archive · Full text
Reader shop tip 1 of 3

Bill Reeks

Individual tip 1 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“Lawn tractors usually get used only for mowing and maybe for towing a small cart or trailer. To make my new Sears Craftsman 17 1/2 hp riding mower more versatile, I removed the hood and installed a bumper equipped with a ball hitch. The bumper has an I-bolt on top of it that allows me to lift the front end of the tractor. As a result, I can sharpen blades without having to remove the tractor’s 42-in. mower deck or reach underneath it. I place a safety stand under the deck so it can’t fall.

From the archive · Full text
Reader shop tip 2 of 3

Bill Reeks

Individual tip 2 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“To charge more than one battery at a time I line up the batteries so that the positive posts are aligned, and then use a vise grip to clamp a wire to all the positive posts. The negative posts are also hooked up in the same way.

This idea allows one charger to charge several batteries at the same time.

From the archive · Full text
Reader shop tip 3 of 3

Bill Reeks

Individual tip 3 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“When using a grease gun, I find an old sock works good to wipe the grease fittings clean before I attach the hose/fitting. A hole in the sock can serve as a ‘thumb hole.’ This idea keeps my hands free of grease and dirt, too.”

From the archive · Full text
Reader shop tip

Roy Breighner

Roy Breighner, Heidlersburg, Penn.

“Years ago, I rescued one of those old-time, manually-operated tire changing machines from a service station that switched to using air-operated machines. It sits out of the way in a corner of my shop until it’s needed. I inserted a length of pipe with a stop welded onto it up through the bottom center part of the machine. I use a chain hoist to lift the machine into a matching pipe that’s cemented flush with the shop floor.”

From the archive · Full text
Reader shop tip

Brian Hageman

Brian Hageman, Decorah, Iowa

“I found an easy way to drain oil out of my Cub Cadet riding lawn mower. The frame doesn’t have a cut out to get at the quick-drain port, so I take a 90∞ sparkplug boot and put it over the drain port. I attach a 1/4 in. hose about a foot long that I run into a jug for disposal. It gets the job done with no mess.

From the archive · Full text
Reader shop tip

Douglas Hall

Douglas Hall, Wilson, N.Y.

When the gear-shift cover on my David Brown tractor became cracked I knew it would be hard to find the replacement parts. So I made a new cover using old rubber boots from the universal drive shaft of a front wheel drive car.

They didn’t quite fit watertight so I used two stainless steel clamps to secure them to the gear shifter. The best part is I didn’t spend more than $15.

From the archive · Full text
Reader shop tip

Pete Peters

Pete Peters, Osler, Saskatchewan

“I made a nut and bolt organizer out of old discs from a disc tiller. I put a 6-ft. piece of pipe through the holes in the center of the discs and welded them 10-in. apart. I can fit about five discs on a 6-ft. section of pipe. The base is another disc flipped over to provide stability. For smaller items you can put on more discs or discs of different sizes.”

From the archive · Full text
Reader shop tip

Kenneth Aller

Kenneth Aller, Louisville, Ohio

“For years we handled material on pallets by hand. We needed an easier, inexpensive way to do the job so we decided to use the loader bucket on our Deere 2555 tractor. We welded a bracket onto each side of the bucket, then mounted a set of forks onto a length of steel

pipe that fits into the brackets. It lets us quickly switch from loading and unloading dirt, sand or gravel to loading and unloading pallets of material - without ever leaving the tractor seat. The bucket can handle up to a 3,500-lb. load.”

From the archive · Full text
Reader shop tip

Dave Cook

Dave Cook, 28800 Cook Road, Washburn, Wis. 54891 (ph 715 373-2092)

Deere’s popular 420 garden tractor, made from 1954 to 1961, could originally be fitted with an optional foot throttle assembly. The company doesn’t make the foot throttle kit any more, so Dave Cook, Washburn, Wis., decided to produce a remanufactured version. The kit also fits the Deere 430 model.

“We copied castings from the original,” says Cook.

“The foot throttle assembly comes in handy for working in tight spots and for doing loader work. It operates in conjunction with the hand throttle and provides foot control of engine speeds.”

Shop feature stories

From the archive · Full text
Feature story

Shop Brightened With Sheet Metal

Featured source:

Mark Siegle will never have to paint the inside walls of his shop, thanks to the bright, reflective sheet metal he lined it with. Fire risk is also less.

Siegle is self-employed as a gas pipeline insulator and sheet metal worker. He noticed that gas plant buildings have metal interior liners made from aluminum sheeting. He liked the look and decided to finish the walls and ceiling of his own 28 by 40-ft. shop with it. The bright metal maximizes light supplied by the shop windows and ceiling fixtures.

The metal lining cost him $20 for each 3 by 8-ft. sheet, bringing his total cost to $2,000. As a finishing touch, he added blue metal trim where the ceiling meets the walls, around the windows, and on the joints between sheets.

Contact: FARM SHOW Followup, Mark Siegle, Box 5878, Westlock, Alberta, Canada T7P 2P6 (ph 780 349-6880; email: [email protected]).

From the archive · Full text
Feature story

Radiator Cleaning Tool

Featured source:

At least half the work of thoroughly cleaning out a radiator is removing it from the vehicle so you can get at it. Harvey Wasson of Perry, Missouri found “a way around that,” by making a tool that allows him to do a good job while it’s still on the vehicle.

Wasson operates a local radiator shop and has plenty of experience bringing radiators back into tiptop shape. The tool consists of a 30 in.-long piece of flexible 3/8-in. hydraulic hose with a 2 1/2-in. long piece of 3/8-in. copper water pipe at one end. The open end is soldered closed. Wasson then welded a flat washer on the side of the copper pipe and drilled three very small holes through the washer and the pipe.

“The holes are bigger than a toothpick and smaller than a matchstick,” Wasson explains.

“They cause the water to come out at a very high pressure. The flat washer is necessary to slide the tool in next to the radiator without damaging the fins.”

At the other end of the hydraulic hose, Wasson installed an adapter to fit a garden hose and an on/off valve.

“I’ve used this tool on radiators in tractors, combines, bulldozers and cars. It works well because it pushes the water straight forward onto the radiator fins so they don’t bend like they would if you tried doing this with a regular 400-lb. pressure hose where you would have to spray the water at quite an angle because you couldn’t reach in properly,” he says.

“I wash one side of the radiator, and then go around and do the other side. This tool was cheap and easy to make.”

Contact: FARM SHOW Followup, Harvey Wasson, Wasson’s Service, Box 56, Perry, Mo. 63462 ph 573 565-2813 (shop), 573-565-2752 (home).

From the archive · Full text
Feature story

Vise-Mounting Bracket For Pickup Tailgates

Featured source:

Charlie Henderson, Burt, N.Y., recently called FARM SHOW to tell us about a vise mounting bracket he came up with. It allows him to quickly attach a vise to the tailgate on his pickup and use it as a workshop in the field.

The attachment has an L-shaped steel plate that hooks over the back edge of the tailgate. A 4 1/2-in. Sears vise mounts on top of this plate. The other end of the attachment clamps onto the front edge of the tailgate using a lever that you push down. To remove the attachment, Henderson simply raises the lever to release the clamping pressure on the front edge of the tailgate.

“I use it on my Chevrolet S10 pickup, but the unit is fully adjustable so it can be used on many different pickup models with different tailgates,” says Henderson.

“Once the attachment is adjusted to fit the tailgate, it can be installed or removed in only about two seconds. The bottom side of the attachment is covered with rubber to keep from marring the tailgate.

“The first model I built used a wrench to tighten a bolt and release the clamping pressure on the front edge of the tailgate. However, the lever is a lot easier to use.”

Contact: FARM SHOW Followup, Charlie Henderson, 5651 Wilson-Burt Road, Burt, N.Y. 14028 (ph 716 778-7827).

From the archive · Full text
Feature story

Replacement Mufflers, Hoods For Farmalls

Featured source:

You can restore the original look and sound of a Farmall tractor with these new replacement mufflers that are built to original specifications, both inside and out.

The mufflers are made from galvanized sheet metal and are designed to fit Farmall H and M models as well as Farmall A, B and C models. They clamp on using a zinc-plated clamp just like on the original mufflers.

“The way these mufflers are built internally is totally different from standard replacement mufflers. They make an altogether different sound that’s beefier and much more mellow,” says Mark Wood, Mark’s Tractors, Gifford, Ill.

“The mufflers are crimped together, with no external welds. At one time, several different manufacturers made original style mufflers for IH, but the last company quit making them about 20 years ago. Most replacement mufflers on the market don’t look or sound at all like the original ones.

“I came up with the idea because I restore tractors and got tired of the replacement models everyone was using. As far as I know we’re the only company that makes an original style muffler for this tractor.”

The mufflers sell for $79 plus $9 S&H. The zinc-plated clamps sell for $7 apiece.

Wood also recently introduced reproduction tractor hoods for Farmall A, B, and C tractors. The hoods attach with spring-loaded brackets .

“The original hoods on these tractors are made of thin sheet metal so they dent easily and also rust out. The thin metal makes it almost impossible to repair them to their original look,” says Wood.

The reproduction hoods are sold as bare, unpainted metal. They sell for $100 plus $15 S&H.

Contact: FARM SHOW Followup, Mark’s Tractors, 2636 County Road 2300 E., Gifford, Ill. 61847 (ph 217 694-4735).

From the archive · Full text
Feature story

One-Handed Pipe Wrench

Featured source:

You’ll only need one hand to use this new, heavy-duty, self-adjusting pipe wrench.

Unlike traditional pipe wrenches, there is no need to tighten an adjustment nut with the RAPIDGRIP wrench. The wrench features a spring-loaded hook jaw design that automatically adjusts to fit pipe or other surfaces up to 2 in. in diameter. A thumb trigger allows users to easily apply or remove it from the work piece.

“Currently the RAPIDGRIP wrench is the only heavy-duty wrench of its type available in the market,” says Matt Ondrejko, product manager, hand tools, at Ridge Tool Co., Elyria, Ohio.

The 12-in. wrench weighs about 5 lbs. and has a jaw capacity of 2 in. It’s made with a cast handle and forged steel jaw with replaceable parts and is backed by the manufacturer with a lifetime warranty.

You can purchase it wherever Ridgid tools are sold, or order it on line at toolup.com or grainger.com. The online price is under $25, including shipping.

Contact: FARM SHOW Followup, Ridge Tool Co., 400 Clark St., Elyria Ohio 44035 (ph 800 769-7743; email: customerservice @ridgid.com; website: www.ridgid.com).

From the archive · Full text
Feature story

They “Respline” Crankshafts

Featured source:

If you’ve got a Deere 70, 720 or 730 tractor equipped with a diesel engine - or another Deere 2-cyl. model - you’ll be interested in this ad we saw in a recent issue of Green magazine.

Renaissance Tractor of Chehalis, Wash., has come up with a new process to repair damaged splines and adjust the nut threads on the crankshafts on Deere 70, 720 and 730 diesel tractors.

“We do a lot of engine work in these tractors and have found they often have damaged splines. However, the journals and bearings are still good,” says owner Albert Ulrich.

“What we do isn’t rocket science but it works. First we magnuflux the crankshaft to make sure there are no cracks in it. Then we use a lathe to turn down any bad spots before welding it back up. If there are cracks in the splined area we can often grind the cracks down and then weld on new material to build the damaged area up again. The lathe is then used to turn down the welded-on material so that it’s round again. The final step is to cut in new splines.”

Ulrich says it typically costs about $500 to respline the crankshaft on a Deere 730.

“A new crankshaft for this model costs about $1,300 so you can save a lot of money.”

According to Ulrich, Deere used this shaft design on a number of different models so the tooling and procedure they use can be applied to a wide vareity of Deere 2-cyl. tractors. He says they may be able to respline crankshafts on other tractors on a case by case basis.

Contact: FARM SHOW Followup, Albert Ulrich, 120 Cabe Road, Chehalis, Wash. 98532 (ph 360 748-0026; email: Albert@renaissancetractor).

From the archive · Full text
Feature story

Best On-Line Sites For Welders

Featured source:

Need help with a welding problem? Or just want to connect with others who share your interest in sticking pieces of metal together? We went looking on-line for the best do-it-yourself welding sites.

Here’s what we found.

1. www.lincolnelectric.com At the main site, you can subscribe to an on-line newsletter and email questions to Lincoln experts. For an extensive library of technical articles on numerous welding topics, you can chase the links from the main page, or go directly to www,lincolnelectric.com/knowledge/articles 2. www.hobartwelders.com or www.MillerWelds.com Both Hobart and Miller Electric are sub-sidiaries of Illinois Tool Works.

Most helpful at these sites is Welding Talk, the Hobart/Miller welding forum, where you’ll find users sharing product information, advice and projects. The forum is overseen by Hobart and Miller experts who frequently chime in with an appropriate “attaboy” or “don’t do that.”

3. www.arcsmith.com/ntt.htm Website for National Torch Tip, makers of flame torch tips for all makes and models of torches, as well as oxy-fuel consumables for an array of applications.

4. www.welding.com This site was founded to let buyers and sellers of welding products get together. The site includes information on products, problem solving, and even welding jobs.

5. www.welding.org Site details training programs of all kinds and training materials such as books, videos, and CDs.

6. www.amweld.org Information here is on welding-related books, events, articles, and products.

7. www.stagesmith.com If you’re just looking for tons of links on additional welding and metal projects, from bike building to jewelry making to machinery repair, check out this site.

From the archive · Full text
Feature story

Trap Pulls Sediment From Fuel Tanks

Featured source:

When John Edwards read the FARM SHOW article on Bill Mossback’s modified filter system for fuel tanks on old tractors (Vol. 27, No. 2), it struck a chord with him.

He has a couple of old Continental 4-cyl. engines that he uses on his farm that run well and have plenty of power to meet his needs. The only problem was that sediment and water in the fuel tanks were frequently too much for the old engines’ sediment bulbs to handle.

To overcome the problem, Edwards came up with a design he says is cheaper and easier to install than Mossback’s. It involves removing the sediment bulb from the bottom of the tank and putting a short pipe nipple in its place. Then he screwed a T fitting onto the nipple and put an elbow on the side of that to which he remounted the sediment bulb. At the bottom of the T, he added another short nipple and then a reducer. At the lower end of the reducer, he screwed in a drain cock.

Fuel still flows through the elbow to the sediment bulb and on to the carburetor, but bigger sediment settles to the bottom of the small sump area created at the bottom of the T fitting.

“Before I start the engine, I open the drain cock and let it run until the fuel comes out clean. Water and rust run out. If the tank has a lot of residue in it, you’ll need to drain it off more often, especially at first,” he says.

“Most gas tanks have 3/8-in. fittings but you can use whatever you need to make the small sump area,” he says. The advantage of this design over an in-tank filter is that over time, this actually removes sediment from the tanks. The only downside is that it lowers the sediment bulb about an inch, so you have to be sure there’s enough room under the tank to install this,” he says.

Contact: FARM SHOW Followup, John Edwards, 11299 County Route 28, Prattsburgh, N.Y. 14873 (ph 607 868-3131).

From the archive · Full text
Feature story

Diesel “Repowers” Provide Cheap Transportation

Featured source:

Tired of high gasoline prices? Don’t mind driving an older vehicle? Maybe you need to follow Mark Overbye’s lead and replace your gas guzzlers with diesels.

Over the past 10 years, Overbye has put diesel engines into two pickups, a Surburban, and a Ford straight truck.

The Lake Alma, Saskatchewan, farmer and cattleman says the first repower job he did was putting a 5.7-liter GMC diesel in a 1965 GMC pickup. He later put a 5.9-liter Cummins diesel from a Dodge pickup into a 1976 GMC crewcab. And for a family vehicle, he put a 6.2-liter diesel in a 1965 GMC Suburban.

“If you have the time, a shop to do the work in, the patience to do it right, and don’t mind driving an older vehicle, you can save a lot of money, particularly on fuel,” he says.

“I’m a mechanic and I have a repair shop on the farm where I work on just about everything,” he says.

“When you go out to get a diesel engine, it’s best to buy the whole vehicle if you can, or at least get as much of the engine and radiator mountings and attachments as possible,” he advises.

“At the time I did the 1965 pickup, I was working off the farm for a John Deere dealer 40 miles away, and needed something cheap to drive to work,” he says. The pickup was inexpensive, but the gasoline engine was worn out. So he found a junked 1984 Oldsmobile with a 5.7-liter diesel in it.

He salvaged the engine and Turbo 350 3-speed automatic transmission from the Olds and sold much of the remainder of the car for parts. He says the engine and transmission fit easily into the old 1/2-ton pickup. He’s put nearly 70,000 miles on the pickup since putting in the engine in 1994.

“I’d heard some negative things about the 5.7-liter diesel, but it was in good shape at the time. I rebuilt the fuel pump and replaced the injectors a few years ago, but it hasn’t given me any other trouble. It’s still going strong,” he says.

Since he was trying to achieve the best fuel efficiency possible, he later changed the gears in the old pickup’s differential.

“It had a 3.73 rear end in it when I got it,” he says.

“I found a 3.08 rear end in a junked early 1970s Chevy and put that into it. That change alone got me another 3 to 5 miles per gallon.”

A few years later Overbye found a 1976 GMC crewcab 4-WD pickup that he could redo.

“I found a junked 1993 Dodge 4-WD with a 5.9-liter Cummins diesel. The engine was fine, but the body was in sad shape,” he says.

The 1976 model wasn’t in much better shape. The cab was fine, but it took parts from several other Chevy and GMC pickups to make it acceptable all over.

“The box came off a 1987 pickup. The front clip is off a 1980 model, and the frame, axles and drivetrain were salvaged from a 1984 model,” he says.

The 5.9-liter was a tight fit under the GMC’s hood, but he didn’t have to cut the firewall or the radiator for it to fit. The biggest problem was that he had to build a new cross member to fit under the crew cab.

“I used the dimensions from the Dodge to pattern the new one, so it wasn’t that difficult a problem to solve,” he says. For a transmission, he left the GMC transfer case in place and attached it to the 5-speed manual transmission that was in the Dodge.

The crew cab pickup has become his primary farm vehicle now, and he uses it for everything from running around the farm to pulling a 5th wheel trailer. He figures he spent less than $11,000 on the crew cab rebuild and repower.

Overbye’s family vehicle is the 1965 Sub-urban.

“I had been looking for an early Surburban for awhile. I finally found a good body in North Dakota. I mounted that on a frame salvaged from a 1980 half-ton Chevy pickup. For an engine, I found a totaled 1982 Chevy Blazer with a 6.2-liter diesel. The engine, mounts and radiator were useable, but not much else,” he says.

“I used the transmission and transfer case from the 1980 pickup in the Suburban. The conversion went so well we get 22 miles per U.S. gallon on the highway.”

He says the easiest conversion he’s done was helping his father-in-law, Kenneth Oberkirsch, put a 3208 Cat engine in a 1977 L700 Ford truck.

“He replaced a 391 cu. in. gasoline engine. The donor engine came from a 1983 Ford 8000 truck. There were more differences in the trucks than I had antici-pated, but the only real problem was finding the right pto shaft to operate the hydraulics on it. He used the 5-speed transmission from the 8000 and the 2-speed rear end from the L700. The clutch and bell housing came from the 8000.”

Overbye says besides fuel savings, he also enjoys the fun and challenge of repower projects. He’d be happy to advise anyone who’s interested in replacing gasoline engines with diesels.

Contact: FARM SHOW Followup, Mark Overbye, Box 213, Lake Alma, Sask., Canada S0C 1M0 (ph 306 447-4708).

From the archive · Full text
Feature story

Narrow Two-Wheel Cart Stores Behind Pickup Seat

Featured source:

Chuck Woods is an avid hunter. But after three back surgeries he couldn’t do any more heavy lifting. Rather than give up on his love of hunting he invented a cart that allows him to transport heavy game with minimal effort. What’s more, the collapsible cart folds up into a package just 6 in. wide, small enough to fit behind the back of a pickup seat.

Woods designed the “Neet Kart” with two in-line wheels so it could be used on deer paths in the woods and fit through narrow barn doors and gates. The big-wheeled cart easily climbs over logs and rocks without losing its cargo due to tie-down straps.

Another advantage of the Neet Kart is that it can pick up a load using the cart itself, saving your back. You just lay the cart down next to the deer or other cargo, tie it on, and then grab the steel frame and lean back using your body weight to pull the cart onto its wheels.

“What’s amazing about it is that I don’t have to lift a single pound. The weight of my body does all the lifting. I use tubular steel for the frame because I don’t want my hunting to be limited by the amount of weight my cart can carry out,” he says. The entire frame is welded completely together, not just in spots.

“I even had a couple structural engineers look it over and give me approval,” he says. It weighs only 32 lbs. because of its tubular steel construction and it folds up in less than five minutes.

Woods’ new cart is so strong that search and rescue units from around the state have expressed interest in using it for their operations.

“The Neet Kart is versatile enough to hold packs, a stretcher, or any other equipment you can think of,” Woods says.

Neet Kart sells for $425.

Contact: FARM SHOW Followup, Chuck Woods, 5300 S. HWY. 2, Libby Mont. 59923 (ph 877 690-4170; [email protected]).