Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 27, No. 4 (2003)

Vol. 27, No. 4 (2003)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

35 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Ken Sharabok

Ken Sharabok, Waverly, Tenn.

“Bushhogging is hard on a muffler. If a limb doesn’t reach out and knock it around, the back and forth jarring tends to weaken or break the weld at the bottom. When I put a new muffler on recently, I made a bracket out of strap metal and angle brackets. The welding is kind of ugly but it’s strong. (Muffler is upside down in photo.)”

From the archive · Full text
Reader shop tip

Ken Corthals

Ken Corthals, Burton, Mich.

“If a little foreign material falls into anti-freeze that I plan to reuse, I filter it with a fine mesh automotive paint filter. It’s the kind of filter that stores often give out for free when you buy painting supplies.”

From the archive · Full text
Reader shop tip

T.J. Shambaugh

T.J. Shambaugh, Oakley, Ill

Fed up with damage to spray booms, T.J. came up with a relatively easy way to hinge the ends of the booms. He used steering ball joints off a truck. Now, if the end of the boom digs into the ground, the hinged section pivots up and back.

From the archive · Full text
Reader shop tip 1 of 2

Cary Urka

Individual tip 1 of 2 from this reader’s published contribution.
Cary Urka, Brethren, Mich.

“I bought this steel rack at an auction for $50, painted it, and bolted it to my shop floor. The rack measures 12 ft. wide, 3 ft. deep, and 7 ft. high. Works great for storing miscellaneous objects, pieces of steel, etc. Bins on one end of the rack are used to store pipe fittings. I mounted a punching bag on the rack for occasional workouts.

From the archive · Full text
Reader shop tip 2 of 2

Cary Urka

Individual tip 2 of 2 from this reader’s published contribution.
Cary Urka, Brethren, Mich.

“I bought this desk at an auction for $5 and use it to store electrical parts, circuit break-ers, etc. I used metal tubing to build a shelf that mounts on top of the desk. I bolted a floor to the bottom side of the desk which I use to store an oil drain pan. Shims were bolted to the bottom side of the floor, allowing me to use my pallet jack to move the desk around.”

From the archive · Full text
Reader shop tip

Elliott Brothers

Elliott Brothers, Montrose, Ill.

Bruce and Roger Elliott built a crusher for oil filters. It reduces filters right down to hockey puck size and pushes out any remaining oil into a catch basin below. They used a piece of box beam with a hydraulic cylinder mounted inside of it. They cut away a lower portion of the box beam to put the filter in and welded it onto a base with a drain hole in it. An electric-hydraulic pump is used to supply hydraulic pressure.

From the archive · Full text
Reader shop tip

Keith Snyder

Keith Snyder, 2435 Route 973 East, Cogan Station, Penn. 17728 ph 570 494- 2627

“My homemade tractor stand mounts on wheels and uses a pair of hand-operated jacks to split the tractor, allowing installation of a new clutch or torque amplifier or removal of the engine. The stand attaches in four places, allowing the front of the tractor to be rolled forward. It allows me to easily move the tractor up or down so I can realign bolt holes and dowel pins during reassembly.

“The stand bolts directly to all Farmall models, from the 400 to the 1586. However, I believe it would also fit other brands of row crop tractors that have a similar front frame design. I’m willing to sell plans to make your own, which would include sizes and details for each piece. I’ll also custom build stands for others on request.”

From the archive · Full text
Reader shop tip

O.E.M. Tractor Parts

O.E.M. Tractor Parts, Rt. 9 East, Box 362, Bloomington, Ill. 61702 ph 800 283- 2122; email

[email protected]): Anyone who restores Farmall tractors will be interested in this new starter coil that’s designed to look just like the original, and work even better. The coil fits all Farmall models ever made. Both 6 and 12-volt models are available.

“It looks much more authentic than using an aftermarket coil,” says Dale Smith.

“It actually works better than the original coils because it uses modern technology, and because it’s wound tighter to provide even more spark. That’s important because with today’s lower octane gas a coil needs more spark.”

Smith says his company offers more than 1,000 different items that you can’t buy anywhere else.

“As far as I know we’re the only U.S. manufacturer that offers original parts to restore International Harvester tractors and make them look as authentic as possible.

Some of the parts we offer include hoods, battery boxes, lights, wiring harnesses, and so on.”

From the archive · Full text
Reader shop tip

Steve Spiering

Steve Spiering, 48594 Hwy. 158, Milbank, S. Dak. 57252 (ph 320 568-2246)

“I made a pull-out drawer for my shop bench that allows me to pull out my chop saw any time I want to cut long stock. The chop saw is bolted to the drawer, which is made out of plywood and rides on a pair of extender rails and inside a couple of brackets that mount on the bench. The drawer has a high back side that catches any debris thrown by the chop saw and keeps it from falling onto the bench. I paid $8 for the rails which I bought at a liquidator store.

“The drawer really comes in handy. I don’t need it if I’m cutting something short, but if I want to cut something long I just pull out the drawer. When I’m done cutting I just push the drawer back in so it’s out of the way.”

From the archive · Full text
Reader shop tip

Elmer Pinkerton

Elmer Pinkerton, Elmwood, Neb.

“I enjoyed reading how Leland Saele of Forth Worth, Texas, used his shop-vac, a 5-gal. bucket, and a 1-quart oil bottle to make an ‘oil vacuum’ for sucking oil out of his Honda lawn mower engine (Vol. 27, No. 3). Many years ago I had a friend who blew out duck and goose eggs so that he could make painted religious decorations. I made him a similar oil vac. From the lid of a 1-gal. wide-mouth jar I soldered in two small copper tubes that go inside the jar - one very short tube and another that’s a few inches longer. Both tubes were kept separate from each other. A rubber hose ran from the long tube up to the vacuum line of a car engine, and another rubber hose ran from the shorter tube to the egg.

“To prepare the egg, a small hole was made in one end of it. A small allen wrench was drill chucked and inserted to scramble the egg contents. Then another hole was put in the other end of the egg.”

From the archive · Full text
Reader shop tip

Lloyd Schade

Lloyd Schade, 35250 Schade Dr., Homer, Alaska 99603 ph 907 235-8949; fax 907 235-3408; email

[email protected]: You can keep expensive gas and diesel fuel from leaking out of your tanks by using this new vacuum relief unit to seal them. The unit automatically relieves the tank’s vacuum as you pump the gas or diesel out for use. It also prevents evaporation of the fuel due to temperature fluxuation. Another advantage is that the pump works easier and the metering is more accurate. The unit works well with gravity flow systems. It fits any standard 2-in. bung on barrels or tanks and can be removed for filling the container. Sells for $17.95 plus $2 S&H.

From the archive · Full text
Reader shop tip

K.L. Morgan

K.L. Morgan, Nampa, Idaho

“Whenever I put weed killer in my backpack sprayer, I put three or four drops of dish washing detergent in it. The wetting agent in soap makes a big difference. It’s cheaper than the fancy stuff used by professional spray companies.”

From the archive · Full text
Reader shop tip

Kevin Weber

Kevin Weber, G&A Farms, Hopkinton, Iowa

Kevin uses a lot of temporary electric fence on his 175-head stock cow herd. Rolling the 17-gauge wire was always an unpleasant chore, until he developed a roller powered by his cordless electric drill. He welded washers and two 1/2-in. nuts onto a 1/2 dia., 8-in. long bolt. He then attached a door handle to one end of the bolt and ground the opposite end of the bolt square to fit into his drill. The door handle is attached so the bolt can spin freely. Washers welded to the bolt near the door handle have smaller bolts attached to the outside of the washers that slip into the end of the spool of wire, so that the spool spins when the bolt spins. Weber says the device lets him roll wire twice as fast as he could before, with much less fatigue.”

From the archive · Full text
Reader shop tip

Ray Baillargeon

Ray Baillargeon, North Battleford, Sask.

“To keep birds out of sheds or other buildings, I use an owl decoy or two, hung from the roof or above the door of the building. The decoy sways in the breeze and acts alive. It works well because birds seem to have an inbred fear of owls. This idea works no matter what the weather.”

From the archive · Full text
Reader shop tip 2 of 3

Bud Hoopes

Individual tip 2 of 3 from this reader’s published contribution.
Bud Hoopes, Beloit, Ohio

I also cut a 3-ft. yardstick off at 12 in. and siliconed it to the lid. It comes in handy for measuring bolts, etc.

From the archive · Full text
Reader shop tip

Elmer Pinkerton

Elmer Pinkerton, Elmwood, Neb.

“In the last issue of FARM SHOW, Charles Poole of Ottawa, Ill., says...’Take an empty steel drum and weld two fittings onto the drum...’ Anyone who welds on a steel drum better have a million dollar insurance policy on his life made out to his wife and kids. A drum can be empty for 60 years and still have enough stuff in the pores of the metal to blow when heated. There are only two results. It might blow and it might not. Is it worth the gamble?”

From the archive · Full text
Reader shop tip

Brent Norton

Brent Norton, Lodi, Ohio

“Here’s a neat, easy way to get oil stains off concrete. Just mix equal parts of cat litter and lime dust and drop it on the stain. Sweep up the compound, and it picks up the oil, and the concrete comes back white.”

From the archive · Full text
Reader shop tip

Woods Equipment

Woods Equipment, Oregon, Ill. Ph 815 732-9395; website: www.woodsonline.com

This company introduces Vintage Iron, a new line of Tisco repair and restoration parts for tractors built from 1939 to 1969. Parts are available for a wide range of brands including Allis Chalmers, Case, Cockshutt, Case/David Brown, Ford, IH/Farmall, John Deere, Massey Ferguson, Minneapolis Moline, Oliver and White. Parts are manufactured to restoration standards.

Shop feature stories

From the archive · Full text
Feature story

Refueling Made Easier With Home-Built Stand

Featured source:

On a busy farm, refueling tractors and trucks is an ongoing task, but Gord Stein of Barrhead, Alberta made the job easier and safer by building a good-looking metal fuel tank stand.

The unit holds three 300-gal. tanks 9 ft. off the ground. Stein hooked two of the tanks together for a 600-gal. diesel capacity, and he uses the third tank for gas.

He included a 2-ft. wide walkway (3 ft. off the ground), complete with a two-step ladder and handrail, for reaching tractor fuel caps. Just beneath the walkway, Stein installed two metal storage compartments for keeping jugs and miscellaneous items.

Another ladder leads up to a tank-level platform. A guard rail makes the lofty perch a safer place to be.

Stein used 2 7/8-in. oilfield pipe for the frame of the stand and metal strap iron for side braces and tank cradles. The ladders and guard rail are made of 3/4-in. sucker rod.

He says materials cost him under $300 (Canada), and it took him about a week to built the unit.

Contact: FARM SHOW Followup, Gord Stein, R.R.#3, Site 2, Box 9, Barrhead, Alberta, Canada T7N 1N4 (ph 780 674-4706).

From the archive · Full text
Feature story

Salvage Yard Specializes In Compact Tractors

Featured source:

Want used or rebuilt parts for Deere, Ford or Kubota utility tractors? Contact James Weaver, Shippensburg, Pennsylvania. Or maybe you have a junked compact tractor you’d like to unload. He might take it off your hands.

Weaver operates Weaver’s Repair, a tractor and skid loader repair business.

“We also buy and sell used compact tractors and loaders,” he says. As an offshoot of the business, he recently started a salvage yard just for compact tractors.

“We have several tractors for salvage parts on hand and are always looking for more,” he says. For the time being, he’s concentrating on Deere, Ford and Kubota brands because they’re more prominent in his area.

Generally, he prices used parts for 50 percent or less of the price of new ones.

“If you want a part rebuilt, we can do that, too,” he says.

Business has been growing steadily as more people learn about the new salvage yard and he anticipates a growing need for whole salvage tractors.

“We can ship parts by UPS or truck freight, and are set up to take Discover, Master Card, VISA, and American Express charge cards,” he notes.

Contact: FARM SHOW Followup, James Weaver, Weaver’s Repair, 9507 Forest Ridge Road, Shippensburg, Pa. 17257 (ph 717 477-9332).

From the archive · Full text
Feature story

Where To Get Hydraulic Pumps Fixed

Featured source:

Need a hydraulic pump repaired? FluidPower Service Corporation can handle any size job, says Ken Jirak, company vice president. While they have big customers like Universal Studios in Florida, no customer is too small.

“There isn’t anybody we won’t help,” says Ken.

“If someone calls with a hydraulic pump problem, we’ll do our best to identify the part numbers and the pump, what it would cost new, and what it would cost to rebuild it.”

Fluid Power offers a full range of services including cylinder reconditioning and hon-ing. They can handle cylinders from 1 1/2 to 16 in. in diameter and up to 25 ft. in length. Not only can they hone, grind and polish, but they can do hard chrome plating as well.

Repair isn’t for every pump, advises the hydraulics expert. If a pump cost less than $300 (generally anything up to 15 to 20 gpm), he suggests it’s probably better to replace than repair.

“If the gear housing goes bad, the plates will go bad,” explains Jirak.

“By the time you invest in a technician’s time to take it apart, replace parts and test it, you will have exceeded the value of a new pump. Higher pressure, higher volume, vane and piston pumps are often more economical to repair than replace.”

Jirak advises carefully studying hydraulic pumps and cylinders before installing them in a machine.

“Why take the time to build a machine around a component if you don’t know if it is good,” he asks.

Before installing or using a used component, Jirak suggests a careful visual exami-nation. Look for wear, especially on the drive shaft.

“If there is wear on the spline-shaft, it will accelerate wear on the coupling. If the unit is performing well, but there is a shaft seal leak or a housing leak, send it in,” says Jirak.

Contact: FARM SHOW Followup, Ken Jirak, FluidPower Service Company, 4474 Walden Ave., Lancaster, N.Y. 14086 (ph 716 681-8474; fax 716-681-8514; website: www.aaafps.com).

From the archive · Full text
Feature story

Foot-Operated Grease Gun

Featured source:

If something is easy to grease, it’s more likely to get greased. That’s what led to the development of this new hands-free, foot-operated grease gun that leaves your hands free to stretch and reach difficult grease points.

The “G. Gun” is a metal canister that’s equipped with a 10-ft. high pressure hose. It holds up to 18 lbs. of grease. The bottom of the unit is equipped with a self-priming pump. A clip-on lid keeps out rain and dust. To grease the zerk you simply step down on a pedal on one side of the canister. The unit can be pumped by hand when used under low machinery.

The company that sells the unit, Horn Trading Inc., supplies grease in handy 5-lb. squeeze pouches for clean and easy filling.

“It holds a lot more grease than hand-held guns and also applies much more pressure,” says Linda Sara.

“The unit has an operating pressure up to 9,000 psi, so it does a good job of dislodging any dirt and grit that may be in the zerk. Unlike air-powered or electric grease guns it has no batteries to recharge or compressor to hook up to.”

Sells for $264 including S&H.

Contact: FARM SHOW Followup, Horn Trading, 11960 New Kings Road, Jackson-ville, Fla. 32219 (ph toll-free 866 756-6775; fax 904 765-2260; email: [email protected]; website: www.horntrading.com).

From the archive · Full text
Feature story

Fuel Tank Sand Blasting Cabinet

Featured source:

“It works great and cost only about $200 to build,” says Rich DeVries, Forreston, Ill., about the sand blast cabinet he built out of a used 250-gal. fuel tank and scrap steel.

He lengthened the tank stand’s legs to 4 ft. A 3-ft. wide, 14-in. high window was cut into one side along with a pair of 7 1/2-in. dia. access holes, spaced 16 in. apart. He fitted the access holes with protective gloves that he bought from a tool and equipment company.

A rectangular-shaped sand hopper welds it onto the bottom of the tank. He cut out one end of the tank and converted it into an access door.

The air-powered blast gun hooks up to a 6 1/2 hp, 220-volt, electric-powered air compressor. A siphon hose runs from the gun down into the sand. When he pulls the trigger on the gun, sand is sucked up out of the bucket and is blown out. A 6-in. dia. exhaust fan removes dust during sandblasting. Three 100-watt bulbs inside a jar hang inside the tank to provide light.

“It works great and can be easily moved around our shop,” says DeVries.

“Commercial sand blasters this size cost up to $4,000. I bought the gloves and sandblaster gun new from an Ohio company called TIPS.

“The blast gun was blowing paint off the back wall of the tank and might have ended up blowing a hole through it so I screwed some vinyl siding onto the wall. The vinyl is soft enough that sand bounces right off it without affecting it.”

Contact: FARM SHOW Followup, Rich DeVries, 10606 N. Hollywood Rd., Forreston, Ill. 61030 (ph 815 938-3393 or 815 238-4494; email: [email protected]).

From the archive · Full text
Feature story

Portable Sand Blaster

Featured source:

For objects that are too large to fit into his fuel tank sand blast cabinet, Rich DeVries used an old supplement feeder to build a portable sandblaster that mounts on four small rubber wheels.

The unit’s metal cone was originally an old A.O. Smith Harvestore supplement meter and measures 30 in. high and 2 ft. in diameter. He mounted a suction tube, made out of conduit, inside the cone.

To use, DeVries transfers the air-powered blast gun and foot-operated valve from the fuel tank cabinet to the portable model. He mounted quick disconnects on the foot-op-erated valve and also on the blast gun to make the job easier.

“It really comes in handy. I can roll it anywhere I want and use it outside my shop building,” says DeVries.

Contact: FARM SHOW Followup, Rich DeVries, 10606 N. Hollywood Rd., Forreston, Ill. 61030 (ph 815 938-3393; email: [email protected]).

From the archive · Full text
Feature story

Skid Steer Motor Swap A Snap

Featured source:

Replacing a fried engine on his Owatonna skid steer loader was a snap for Brent Norton, Lodi, Ohio, who replaced the original engine with a 24 hp Onan engine. The biggest problem he had was matching the crankshaft on the engine to the shaft on his skid steer. It turned out to be simple to resolve.

“I laid two pieces of 1 by 1-in. rebar stock parallel across the frame and then set the motor on it,” he says.

“Then I shimmed the motor up until the shafts matched and then bolted the engine down to the frame and double nutted it. It locked the rebar and the shims in place.”

Because 2-cyl. engines are noted for backpressure, Norton modified the exhaust system from a single stack to a double stainless steel pipe. He notes that the double stack has kept the motor running cooler. The only other modification he had to make was to run an extension made from coolant hose from the original air cooler to the new carburetor.

Norton uses his skid steer primarily for snow moving and for forklift work. After getting it running again, he cut a manure fork bucket apart and rebuilt it with pallet forks. This allows him to use the unit to store pallets of items on shelves in his barn.

Contact FARM SHOW Followup, Brent Norton, 8389 Congress Road, Lodi, Ohio 44254 (ph330 948-3307).

From the archive · Full text
Feature story

Hot Water Pressure Washer

Featured source:

George (Bing) Ribble converted a used power unit from a commercial car wash into a low-cost, portable pressure washer. When he needs hot water to wash, he hooks it up to a 40-gal. gas water heater that stands next to a water hydrant outside his shop building.

The pressure washer mounts on a 2-wheeled cart and is operated by a 5 hp electric motor, which belt-drives a 3-piston pump.

“I got the washer power unit from my nephew who works for a company that makes commercial power wash systems. It was originally powered by a 1 1/2 hp electric motor, which didn’t have enough power for my needs so I replaced it with the 5 hp motor. The power unit was originally equipped with a single-groove pulley which I converted to a double-groove. It can pump at up to 2,000 lbs. pressure so I have to be careful when using it,” says Ribble, of Hettick, Ill.

“I built it for less than $200. It works as good as commercial hot water pressure washers that sell for $2,000 or more. I collect antique tractors and use it a lot to keep them clean. The hot water works great for washing grease and dirt off the tractors. I already had the motor. I paid $100 for the car wash power unit and got the hot water heater free from someone who wanted a new one.”

Contact: FARM SHOW Followup, George (Bing) Ribble, 25766 Mt. Ragan Rd., Hettick, Ill. 62649 (ph 618 778-5752).

From the archive · Full text
Feature story

Do-It-Yourself Sandblast Cabinet

Featured source:

Want to build your own sandblasting cabinet, but at a loss as to where to start?

TP Tools has kits and plans for sale. Kits start at $159. Plans are $7.50.

They’re available through their catalog, toll-free number, or on their website by click-ing on the blasting cabinet and then on “nozzles, jets, kits, plans, parts.”

Contact: FARM SHOW Followup, TP Tools & Equipment, Division of Tip Plus Corp., 7075 Route 446, Box 649, Canfield, Ohio 44406 (ph 800 321-9260; website: www.tptools.com).

From the archive · Full text
Feature story

They Rebuild IH Hydro Tractor Transmissions

Featured source:

If you own an older model International Harvester “Hydro” tractor, you’ll be interested in the service provided by an Iowa company that rebuilds the tractor’s hydrostatic transmission at far less cost than the price of a new transmission.

Steffen Fluid Power, Sioux City, Iowa has been rebuilding hydrostatic transmissions on IH tractors for years, mainly for another company. Now they’re expanding their efforts to include working directly with farmers and local repair shops.

“The charge pump is the part that fails most often on these transmissions,” says Dave Harder.

“Unfortunately, you can’t buy parts to repair the charge pump from Case IH. The alternative is to buy a new charge pump from Case IH for more than $2,000, or try to find a replacement charge pump at a salvage yard. However, it’s hard to find a replacement charge pump at salvage yards because they all get worn. To solve the problem, we con-tract with a machine shop that makes the parts we need to rebuild the pumps. So instead of spending more than $2,000 for a new charge pump, we can usually rebuild the one you already have for about $600. The pump fits right into the tractor transmission without requiring any modification to the tractor at all. Usually, rebuilding the charge pump is part of a complete transmission rebuild.”

Harder says they can completely rebuild the hydrostatic transmission on any of the 12 different IH Hydro tractor models, all of them built before the early 1980’s.

“There are a lot of old IH hydrostatic drive tractors still out there working every day. Farmers like them for doing chores and especially for loader work.”

Contact: FARM SHOW Followup, Dave Harder, Steffen Fluid Power, 623 West 7th St., Sioux City, Iowa 51103 (ph 800 783-3832; email: [email protected]).

From the archive · Full text
Feature story

“Downdraft” Cutting Table

Featured source:

After Brad Noth bought a Hypertherm 1000 plasma cutter, he decided he needed a better cutting table and ventilation system.

“The plasma cutter is an excellent machine but it produces a lot of heavy smoke,” he says.

So he built a portable downdraft cutting table equipped with its own fan exhaust. Smoke is pulled down through the table, which is partially open on top. From there it goes through a pair of curved 8-in. dia. pipes to a couple of squirrel cage fans mounted on one side of the table. The fans are belt-driven by a 1 hp 1,725 rpm electric motor.

The 3-ft. high table measures 4 by 5 ft. and has drop-in grates made from 3/16-in. thick, 1 1/2-in. wide flat stock. A hopper under the table funnels sparks and slag down into a re-movable catch pan. A pair of 8-in. dia. holes were cut halfway up on opposite sides of the hopper. Elbows and some short lengths of stove pipe connect the holes to the fans.

An extension cord is attached to a switch that he mounted on the table. Whenever Noth wants to use his plasma cutter, he pushes the table next to an overhead garage door and raises the door a foot or two so he can blow the fan exhaust outside.

“I was surprised at how well it works, especially because I had never seen a downdraft system like this before,” says Noth.

“It works much better than a hood system and is also much cleaner and healthier. The fans are two 1/3 hp 1,000 cfm single-inlet radial blowers that I found at a local repair shop. Since the fans are symetrical, I had to reconstruct one fan wheel so that I could run both fans back-to-back on a single shaft with a pulley in between them.”

Noth estimates his total cost to build the table at about $500.

Contact: FARM SHOW Followup, Brad Noth, 9018 Enterprise Road, Tomah, Wis. 54660 (ph 608 372-3191).

From the archive · Full text
Feature story

Log Splitter Breaks Beads

Featured source:

“I use my vertical log splitter to break the beads on car and implement wheels. It works slicker than a whistle,” says Dick Carey, Shell Rock, Iowa.

Carey bought the splitter from a neighbor who had built it. It uses a pto-operated pump to drive a 10-ton hydraulic cylinder with a V-shaped wedge that Carey welded onto it. The cylinder mounts on top of a rectangular steel frame. A hand-operated control on back of the splitter is used to raise and lower it.

To break the bead, Carey places the tire on top of a 1-ft. long wooden block inside the frame opening.

Contact: FARM SHOW Followup, Dick Carey, 33636 290th St., Shell Rock, Iowa 50670 (ph 319 987-2610).

From the archive · Full text
Feature story

Custom Gaskets For Any Purpose

Featured source:

If you need a gasket for an older engine or machine, call Lubbock Gasket & Supply, Lubbock, Texas.

They stock head gaskets for many older engines and maintain a supply of other higher demand gaskets for older farm, construction and oil field equipment.

And if they don’t have the specific gasket you need, they’ll make it for you. Eddie Smith, general manager, says if you have the original gasket, that’s their best pattern to use for making a new one. Without the original, you’ll need to supply them with a tracing or accurate drawing of the gasket, complete with dimensions. You’ll need to measure hole sizes, distance between holes, metal thickness, etc. And you’ll need to tell them what material and thickness to use.

Lubbock Gasket makes gaskets from cork, graphited asbestos, or from either soft an-nealed copper or solid copper.

“If you don’t know what material you need, send us a piece of the old gasket and we’ll try to match it,” Smith says.

“We do a lot of business with engine rebuilders who re-bore cylinders and need head gaskets that are no longer stock,” he says.

“We also work with tractor pullers who modify their engines. We keep a file on these, so if someone needs a replacement for one of our custom gaskets, we can make it up quickly. Or if they bought a pulling tractor or modified engine from someone we’ve dealt with, they can call us with just the information on where they got the engine and we can make them a new one.”

In addition to custom flat gaskets, Lubbock Gasket also keeps bulk O-ring material in stock and can make O-rings to your specifications.

Contact: FARM SHOW Followup, Lubbock Gasket & Supply, 402 19th Street, Lubbock, Texas 79401 (ph 800 527-2064; fax 806 763-0965; email: [email protected]; website: www.lubbockgasket.com).

From the archive · Full text
Feature story

Space-Saving Mower Deck Storage

Featured source:

“I built it because my Kubota mower deck was taking up too much floor space in my garage,” says Larry Cohenno, Willet, N.Y., who came up with a pair of small wheels and axles that allow him to store his 60-in. deck vertically instead of horizontally.

“Every year I remove the deck for the winter so that I can install a snow blade on the tractor. This idea saves space and also makes the deck easier to service,” says Cohenno.

The patent pending axles are 13 in. long and fitted with 3-in. high wheels. They mount in place of a pair of anti-scalping wheels on back of the deck. Cohenno simply pins the axles on in place of the scalping wheels.

The axles are made from 1-in. dia. steel.

“The kit is designed specifically for Kubota mid-mount mower decks, but I think the same idea would work with other brand name decks using four anti-scalp wheels with 1-in. dia. shafts. The wheels are rated at 250 lbs. apiece so I don’t think they’d have any problem supporting a 300-lb. deck,” notes Cohenno.

Cohenno sells the wheels and axles on Ebay.com and Tractorbynet.com for $69.95 including S&H in the 48 contiguous states. He also wholesales them to dealers for $62 who sell them at a retail price of $99.95.

Contact: FARM SHOW Followup, Larry Cohenno Sr., 710 State Route 26, Willet, N.Y. 13863 (ph 607 863-4208; email: [email protected]).