Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 48, No. 1 (2024)

Vol. 48, No. 1 (2024)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 32–35

30 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Larry Goodman

Larry Goodman, Ionia, Mich.

“I accidently cut the cord while I was trimming shrubs with my electric hedge trimmer. While I was fixing the cord, I had the idea to hook a carabiner clip to my belt loop and run the extension cord through it. The cord moves easily and it’s out of the way.”

From the archive · Full text
Reader shop tip

Ronald Hurst

Ronald Hurst, Knoxville, Tenn.

“This is a handy, fairly inexpensive tool that turns a round hole (3/8 in.) in sheet metal into a rectangular hole, any size. I use my nibbler mostly for squaring holes in electrical/electronics projects (holes for things like digital displays, fuse holders, snap-in rocker switches, etc.).

“Nibbling tools exactly like this one sell online for anywhere from $7 to $16. One nibbler that I saw was a slight variation on this tool and was being sold for around $75. It was sold as a special tool for fine trimming of new metal frets for guitar necks, but from the look of that tool and the reviews that it received, I don’t think it was any better quality than the less expensive one pictured here.”

From the archive · Full text
Reader shop tip

Larry Harrington

Larry Harrington, Western, Neb.

“When adding the additional front generator pulleys on Deere irrigation engines, sometimes the original pulley comes loose, and the new pulley won’t stay on the crankshaft. In many cases, I’ve machined the crankshaft straight and rebuilt the pulley without removing the crank from the engine. The engine does have to run for this to work.

I’ve done this over 10 times without failure. It also works on some other engines.”

From the archive · Full text
Reader shop tip

Dale McLaen

Dale McLaen, Rutland, N.D

“Repeated plug-ups in the fuel filter between the tank and carb caused me to follow the fuel.

“I did an autopsy on the fuel filter and found it full of tiny, black, rubber-like particles. The tank was spotless, so I cut open the rubber fuel line. It looked fine on the outside but was junk on the inside.

“The rubber line had degraded and was falling apart internally. As it did so, rubber particles found their way to the fuel filter.

“A new fuel hose fixed the problem. If you see black particles in the fuel filter, check the fuel line.”

From the archive · Full text
Reader shop tip

Grady Hurst

Grady Hurst, Knoxville, Tenn.

“For lack of a better name, this is a ‘Pedal Presser Downer’ tool. You press down the gas or brake pedal of a car or track and put this tool in place to hold the pedal down. This idea came from an auto mechanic whom I worked with briefly in 1984. It’s easy to make and is a handy tool to have for checking brake lights, adjusting the brake light switch, temporarily increasing engine speed for battery charging or making other adjustments.

“The dimensions can vary, depending on what scrap materials are used and what vehicle or machinery it’s used on. For this one, I used 2 ft. of 1 in. dowel and a plank that’s 1-in. by 2 in. by 12 in. The hole in the plank is 1/8 in. larger than the dowel’s diameter. It’s a close fit so that the plank has to be only slightly out of square with the dowel to lock it in place on the dowel. A nail in each end of the dowel keeps the plank from sliding off when the tension is relieved.”

From the archive · Full text
Reader shop tip 1 of 3

Barry Swartz

Individual tip 1 of 3 from this reader’s published contribution.
Barry Swartz, Harleysville, Penn.

“Here’s a tire repair tip: I clamp a vise grip pliers onto the rim to stop a tire from ‘walking’ around the rim when trying to remove it.

From the archive · Full text
Reader shop tip 2 of 3

Barry Swartz

Individual tip 2 of 3 from this reader’s published contribution.
Barry Swartz, Harleysville, Penn.

“Got a nut that’s rounded off so you can’t remove it? Just spot-weld a second nut on top of it, using as big a nut as possible. Then turn it right off.

From the archive · Full text
Reader shop tip 3 of 3

Barry Swartz

Individual tip 3 of 3 from this reader’s published contribution.
Barry Swartz, Harleysville, Penn.

“To keep crop material from getting caught in the gap between the shield and wing on my discbine, I attached a flat metal tab to the shield to fill the gap between the shield and wing. Works great and doesn’t keep it from folding.”

From the archive · Full text
Reader shop tip 1 of 2

John Rochester

Individual tip 1 of 2 from this reader’s published contribution.
John Rochester, Charlotte, N.C.

“To make it easier to work hands-free in tight spaces, I attach a heavy chunk of metal to the magnet base of my rechargeable wireless work light. Holds it solidly in place.

From the archive · Full text
Reader shop tip 2 of 2

John Rochester

Individual tip 2 of 2 from this reader’s published contribution.
John Rochester, Charlotte, N.C.

“Here’s a good way to lengthen a rubber cargo strap. Just attach a piece of light chain. The chain won’t stretch and won’t jam up with knots.”

From the archive · Full text
Reader shop tip

Joseph Polonowski

Joseph Polonowski, Grand Rapids, Mich.

“In the latest edition of FARM SHOW, I read a report from a reader about his Milwaukee cordless saw that leaks oil after use. I have a suggestion that might help: When he’s finished using the saw, he should unscrew the cap on the oil tank, wait a couple of seconds, and then reinstall it. The pressure in the oil tank is often what causes the oil to squirt onto the bar and chain. With the cap off for a couple of seconds, the pressure releases, and the saw should stop leaking – or leak less – after use.”

From the archive · Full text
Reader shop tip 1 of 2

Fritz Groszkruger

Individual tip 1 of 2 from this reader’s published contribution.
Fritz Groszkruger, Dumont, Iowa

“The sliding doors on my pole barn used to be held in the center by a buried post with a welded piece that fit between the rails. It didn’t hold up, so I came up with the idea of using a pair of buried truck tires, spaced so the doors slide between them. Works much better.

From the archive · Full text
Reader shop tip 2 of 2

Fritz Groszkruger

Individual tip 2 of 2 from this reader’s published contribution.
Fritz Groszkruger, Dumont, Iowa

“The seal went bad on our old freezer, and we couldn’t find a replacement. Instead, we installed these toolbox latches that let us close the door really tight. Problem solved.”

From the archive · Full text
Reader shop tip

James B. Froelich

James B. Froelich, Cumberland, Md.

“I like to wear disposable nitrile gloves when doing dirty mechanical work, but they can be hard to put on. I sprinkle a little baby powder into them to make them much easier to slip into.”

From the archive · Full text
Reader shop tip 1 of 2

Ben Parks

Individual tip 1 of 2 from this reader’s published contribution.
Ben Parks, Austin, Texas

“With all the electronic devices around these days, I came up with an easier way to keep track of the USB cords I need. I bundle up a group of cords and color code the ends for certain types of devices. It lets me grab the whole bundle of cords without having to sort through a bunch of them to find the one I need. I also mark the top side of each USB plug so I can tell at a glance which is the top side when plugging in.

From the archive · Full text
Reader shop tip 2 of 2

Ben Parks

Individual tip 2 of 2 from this reader’s published contribution.
Ben Parks, Austin, Texas

“On 2-prong electric cords, I use permanent markers to mark the wide end so I can plug them into a 120-volt outlet the first time without having to look at the prongs. I use a black marker on a light-colored cord and a white marker on a black or brown cord.”

Shop feature stories

From the archive · Full text
Feature story

Battery Adapters Offer Tool Flexibility

Featured source: FARM SHOW

As professionals, hobbyists, and homeowners look to expand their power tool collections, they often feel limited to one brand due to exclusive battery systems. Going outside the brand means investing in additional batteries and chargers and finding storage solutions. Battery adapters allow users to use batteries from one brand with tools from another, giving users the flexibility to choose the best tool for the job without concern for battery compatibility. Most adapters are compact and easily attached to tools. We looked to social media accounts we follow for any standouts.

“Modern Milt” from Instagram recommends two different adapters. One is the ZDTAN MIL18DL for Milwaukee M18 18V batteries to DeWalt 20V lithium-ion battery tools ($21.99 on Amazon). The other is the Echoyee for DeWalt 18V or 20V lithium batteries to Milwaukee M18 tools ($16.88 on Amazon). While battery adapters offer a compatibility solution, there are a few things to consider before purchasing. Some adapters may not support all the features of the original battery, including battery life indicators.

Most don’t contain a cut-off system to stop the battery from being used past the point of rechargeability, so it’s important to stop using the battery when performance starts to drop. The adapters need to be compatible with the voltage and power requirements of the tool to avoid damage.

From the archive · Full text
Feature story

Cleanout Door Cut In Skid Steer Frame

Featured source: Simon Oyler, Delphi, Indiana

Indiana crop and livestock farmer Simon Oyler has a simple way to clean out trash, dirt, and other materials from inside the pan of his and his dad’s L220 and L230 skid steer loaders.

“Instead of having to vacuum or blow out all the crud from inside the chassis, I cut a small trap door on the front of the frame where the hydrostatic motors are. Now I can blow out or wash out the debris, then replace the plate cover until it’s time to clean it again.” After cutting the frame, Oyler made a plate to cover the opening, then drilled tap holes and screwed the cover in place.

“It’s a simple idea that doesn’t affect the machine operation,” Oyler says.

“Now, when we tip up the cab to clean the machine, we remove the cover, and cleanout is very easy.” Contact: FARM SHOW Followup, Simon Oyler, Delphi, Indiana.

From the archive · Full text
Feature story

He Stores Extra Metal In Tote Frames

Featured source: Richard Arcement, Napoleonville, La.

Richard Arcement uses IBC tote frames as storage racks for scrap steel. Even better, by mounting the frames on a boat trailer, they’re mobile. The retired sugar cane farmer and mechanic can take them wherever he needs the steel. The trailer also makes it easy to get them out of the way when he needs space in the shop.

“I store signposts, angle iron, steel pipe and pvc pipe, anything I need to pick up around the shop,” says Arcement.

“It’s nice to have everything in one place, but also nice to be able to move it around as needed.”

Arcement had the frames, and putting them on the boat trailer made the concept more user-friendly. The trailer, which once carried a small aluminum boat, was wide enough to mount one tote frame at the rear over the 12-in. wheels.

“I just welded it in place,” says Arcement.

“To mount the other tote frame, I needed to add some cross pieces over the trailer frame where it narrows closer to the hitch.”

He welded two pieces of bed frame angle iron to the trailer frame and then welded the tote frame to it.

“Bed frame angle iron is great,” says Arcement.

“It’s made of stress-proof steel, and you can’t bend it. I use it for all kinds of projects.”

Moving the trailer around even when loaded with steel is easy, thanks to a short boom Arcement made for his 32-hp. Ford tractor.

“The boom mounts to the 3-pt., making it easy to pick up the hitch and pull or push the trailer around.”

Contact: FARM SHOW Followup, Richard Arcement, 3615 Hwy. 1, Napoleonville, La. 70390 (ph 985-637-1538).

From the archive · Full text
Feature story

Jerk Rope Pulls And Tows Them All

Featured source: Jerk Rope / Red Barn Manufacturing, Coldwater, Kan.

The shock-absorbing rope featured in 2016 (Vol. 40, No. 1) is still just as handy for farmers pulling stuck equipment out of the field or semis out of a ditch.

It eliminates the “jerk” when pulling and it’s much safer.

“Jerk Rope works like a shock absorber and has more pulling energy. If it does break, there’s no explosive recoil to fly through a cab,” says Jon Levendoski, one of the owners.

With Grade 100 oblong links and a patented braided nylon web assembly, Jerk Rope hooks up to chains, straps, and cables used for pulling and towing. At less than 2 ft. long, the smallest version, the Mini Jerk, sells for $287.50 and is small enough to store in a vehicle and powerful enough to pull 20,000 lbs.

Bigger versions pull even more: Little Jerk, 54,000 lbs.; Junior Jerk, 75,000 lbs.; and Big Jerk,100,000 lbs.

“Since 2016, farmers, county workers, and fire departments have used them for vehicles and equipment stuck in the sand, snow, or mud,” Levendoski says.

“Quick extraction and the safety factor are the important advantages. The Jerk Rope is OSHA and MSHA compliant and is also used in the mining industry,” Levendoski adds. He cites one example when Jerk Rope was used to pull a 6x6 articulated dump truck after a 4-in. snatch strap broke. Videos on the website show examples of pulling out several pieces of equipment. The Jerk Rope is made in the U.S. and is available for sale on the website and through dealers listed on the website.

Contact: FARM SHOW Followup, Jerk Rope, Red Barn Manufacturing, P.O. Box 427, Coldwater, Kan. 67029 (ph 715-381-9948; [email protected]; www.jerkrope.com).

From the archive · Full text
Feature story

Hydraulic Hose Crimps Where Needed

Featured source: Parker

The KarryKrimp line of portable hose crimpers from Parker lets you make hydraulic hoses when you need them, where you need them. Any user can make factory-quality hose assemblies quickly, easily, and cost-effectively. Crimp the fitting to the proper diameter every time. The crimpers are easy to operate and built to provide years of dependable service. They can crimp straight or bent-stem fittings.

The KarryKrimp hydraulic hose crimping machine provides up to 30 tons of force to crimp heads on hoses from 1/4-in. up to 1 1/4-in. ID, 2-wire braid, and up to 5/8-in. ID, 4-wire braid. It weighs just 55 lbs. The crimper operates at up to 10,000 psi. It has a length of 12 in., a width of 15 in., and a height of 30 in. It comes with two dies, a crimp head, hose assembly, and a stand. It’s priced at $5,360 at Grainger.com. The crimper tool alone is priced at $2,600 on the Parker website.

The KarryKrimp 2 has a 60-ton force and can crimp 1 1/4-in. ID, 2-wire braid, 1-in. ID, 6-wire spiral, and up to 1 1/4-in. ID, 4-wire spiral hoses.

The portable crimper does not include a power source. It can be used with any of the six pumps from Parker. They include small and large hand pumps, small and large electric pumps, an air/hydraulic pump, and a vehicle battery-powered pump. All deliver up to 10,000 psi. Prices are available from distributors.

The Parkrimp family of crimping machines offers a broad array of crimping equipment from small to large and portable to bench or floor mount. Visit the Parker website for a list of local distributors. Some products are for sale directly from Parker.

Contact: FARM SHOW Followup, Parker (ph toll-free 800-272-7537; [email protected]; https://ph.parker.com).

From the archive · Full text
Feature story

Heat Up Your Farm Buildings With These Large Heaters

Featured source: Nick Reilly, Fortville, Ind.

Advanced Radiant Systems is helping farmers keep large pole barns and high-ceiling shops warm in cold weather.

Its gas-fired, natural gas or propane, single-stage unitary range radiant heaters are rated up to 220,000 Btu/hr. and run off a standard 120-volt electrical supply.

“These systems heat the concrete and not the air,” says Nick Reilly, National Sales Director.

“The heat comes from the ground up to where it’s needed, so you get a warmer temperature at the ground level rather than at the ceiling.”

Standard features of the heaters include aluminum combustion tubes and gasket, direct spark ignition, heavy-duty couplers, a self-diagnostic ignition module, and parabolic aluminum reflectors.

U or L-shaped bends for specific layouts, side shields, brackets, and termination vents are optional.

“Farmers like them for their larger buildings because they heat from the bottom to the top,” Reilly says.

“If they’re opening big overhead or sliding doors, heat recovery times are quicker than with other systems.”

The radiant heaters come in 10 to 70 ft. lengths and range in price from $1,200 to $3,200 plus S&H.

Manufacturing is in Indianapolis, with the heaters distributed by a network of dealers throughout the U.S.

Contact: FARM SHOW Followup, Nick Reilly, Advanced Radiant Systems, 315 N. Madison St., Fortville, Ind. 46040 (ph 800-874-3285; [email protected]; www.advancedradiantsystems.com).

From the archive · Full text
Feature story

Heavy-Duty Custom Truck Toolboxes

Featured source: Myron Thiessen, Winkler, Manitoba, Canada

Time and tools are valuable commodities to service truck owners. Drawer Packs save both of them, says Myron Thiessen, parts manager for Soaring Eagle H.D. Truck Parts and Accessories.

About 3 years ago, the Canadian manufacturers, noted for building semi-truck HVAC boxes and other trucking accessories, responded to customers’ requests to build toolboxes for their service trucks.

“They came to us and said how difficult it was to get what they wanted in a timely manner that was cost-effective,” Thiessen says, instead of the 30 to 40 weeks it was taking to get custom toolboxes.

Soaring Eagle came up with a design to keep standard sizes on hand and the ability to deliver product within 1 to 2 mos. For more custom sizes, turnaround time is 2 to 4 mos.

Customers order the overall size they need and specific drawer measurements to hold their tools. Built with heavy-duty slides and 11-gauge aluminum, each drawer can hold up to 500 lbs.

“Each drawer is removable to allow customers to move parts or tools to any area of their job site,” Thiessen says, and each drawer has a lock and key. Customers like the handy T-handles that make it easier to open the drawer when wearing heavy gloves.

Drawer Packs range from standard models at $1,100 to $4,000 for completely customized orders.

“We’re a younger, smaller company, so we work with our customers to give them personal attention,” Thiessen says. That means customers receive quotes quickly and aren’t handed off from one department to another.

All products can be ordered directly from the company and shipped anywhere in the U.S. and Canada.

Contact: FARM SHOW Followup, Soaring Eagle H.D. Truck Parts and Accessories, 465 George Ave., Winkler, Manitoba, Canada R6W 0J4 (ph 204-331-4000; toll-free 833-455-2473; [email protected]; www.soaringeaglehd.com).

From the archive · Full text
Feature story

These Holders Secure And Protect Tools

Featured source: Kiley Faggionato, Monroeville, Ohio

D-Lock tool holders can hold securely in place shovels and other tools on all types of vehicles. Made in the U.S. by Jones Manufacturing Inc., they’re a smaller version of the company’s J-Lock load lock holders that semi drivers use to secure load locks on the back of their cabs.

“There’s nothing like this out there,” says Kiley Faggionato, owner of Jones Manufacturing.

“Tools clamp in the D-Lock, and there’s a bar to keep them in place.”

The tool racks accommodate all types of long-handled tools, such as shovels, rakes, brooms, sledgehammers, hoes, pitchforks, post-hole diggers, and come-alongs.

Besides preventing tools from moving, the system helps deter theft.

Made locally in Ohio, the locking springs and parts are powder-coated and durable. Different configurations, starting with 2-tool holders ($53.90 plus S&H), make the D-Lock versatile to work on equipment trailers, dump trucks, toolbox tops, and other equipment.

“They’ve been available for about 15 years, so they’re well tested,” Faggionato says. Jones Manufacturing sells the holders and other products through its website, has partnered with several OEM dealers, and welcomes inquiries from dealers.

Contact: FARM SHOW Followup, Jones Manufacturing, 20 Fort Monroe Industrial Park Ave., P.O. Box 143, Monroeville, Ohio 44847 (ph 419-465-2009; [email protected]; www.jones-mfg.com).

From the archive · Full text
Feature story

How To Read Your Tire Sidewalls

Featured source: Dawson Tire & Wheel, Gothenburg, Neb.

Tires aren’t cheap, so it pays to know all you can about them. Tire sidewalls are loaded with information if you know how to interpret it. When Dawson Tire & Wheel introduced their TreadSure App (Vol. 47, No. 6), they also built a website that highlights the information on sidewalls and what it means.

“Five Parts of A Sidewall You Should Know” is the title of the website page. The information starts with the tire size label with its four data points. • Tire width and distance between sidewalls and the letter code that designates load capacity. • The ratio of sidewall height to the tire width. • The third data point, if present, is a letter such as R for radial. • Numeric code for the rim diameter in inches The largest amount of data on the sidewall lists the speed rating and load index number for the tire. Speed ratings are indicated by a letter or letter and number for the maximum speed, such as A2 for 6 mph up to G for 55 mph. Many implement and passenger car tires have ratings far beyond G.

The load index number is a 3-digit code for the carrying capacity at its proper pressurization and speed. Dawson Tire & Wheel offers a tire chart with common index codes and their pound/kilogram equivalency.

A second speed/load rating present inside a circle indicates being able to travel at a faster speed under a reduced load.

Also found on the sidewall is a date code for when the tire was made, preceded by a letter code for the company that made it.

Other information elements on the sidewall include the bead seating marker for the inflation pressure needed to set the bead and the tire safety warning.

While on the website page, request Dawson Tire & Wheel’s Tire Chart. It’s a powerful aid to understanding correct tire pairings for fronts and backs, ply rating symbols, speed rating symbols, and bias-to-metric conversions. It also covers carrying capacities, an equivalency table, and more.

Contact: FARM SHOW Followup, Dawson Tire & Wheel, P.O. Box 128, Gothenburg, Neb. 69138 (ph toll-free 888-302-5926; [email protected]; https://treadsure.app/how-to-read-the-sidewall-of-an-ag-tire/).

From the archive · Full text
Feature story

Garage Lift Adds Handy Storage

Featured source: Greg Smith

Powerline’s Vantage motorized storage lift creates extra storage space in your garage for your “stuff” and your vehicles, says Greg Smith, owner of the Indianapolis company.

In his previous business, he sold thousands of car and truck above-ground lifts. In retirement, he noticed that people were parking expensive cars in the driveway because their garages were filled with “other stuff.” Smith designed and patented a single-column storage lift to solve the problem.

“The Vantage storage lift is anchored to the concrete floor just like a two post above ground lift,” Smith says, noting concrete floors should be at least 3 1/2 in. thick.

There are two column heights and four platform sizes available. The platforms easily raise and lower 1,500 lbs. and the motorized lift is a much safer and easier option than manually carrying things up and down a ladder.

“The turned single-column design allows the storage lift to be mounted in just about any garage location,” Smith says. A garage ceiling height of only 8 ft. has plenty of available overhead storage space.

The lifts are designed to raise and lower heavy items such as ZTR mowers, UTVs, ATVs, motorcycles, and golf carts, in addition to patio furniture, holiday decorations, and an assortment of totes.

The steel component parts of the Vantage storage lift are powder coated. The motor and cable pulley system are factory assembled to the column. Customers need to provide their own decking material (plywood is the most popular). Smith says installation is fairly simple and takes two able-bodied people about 4 hrs. to install.

The servo motor operates on 110V or 220V with no modifications. The 220V raises and lowers twice as fast as 110V. The electric motor and cable pulley system is more user-friendly than a hydraulic lifting system, and the wireless remote operates the lift from over 50 ft.

Prices range from $3,800 to $5,400, plus freight costs in Indianapolis, Ind. The lifts are also available for customer pickup. Smith welcomes inquiries from potential dealers interested in having multiple units drop shipped.

For FARM SHOW readers, Smith is offering 10 lifts at a special marketing promotion of 40 percent off the website pricing. Customers pay all freight costs and agree to provide videos/photos of the installed lift.

Smith notes that by Spring 2024, a 12-ft. column platform storage should be available.

“It’s perfect for farmers and ranchers with overhead mezzanine storage in their outbuildings,” he says.

Smith notes that the Powerline website has videos and pictures to help customers understand how the lift creates additional garage floor space out of cubic air space.

Contact: FARM SHOW Followup, Powerline Vantage Storage Lift (www.powerlinelift.com).

From the archive · Full text
Feature story

How To Keep Tall Vehicles Snow-Free

Featured source: Angel-Guard Products, Worcester, Mass.

Angel-Guard Products has developed the Mobile RoofBrum, a unique tool for cleaning snow from even the tallest commercial and agricultural equipment. The RoofBrum comes with a three-piece, 12-ft. long adjustable handle. A 60-degree bend attachment helps reach and remove snow from high platforms while standing securely on the ground. The oversized head is non-abrasive and made from durable cross-linked polyethylene foam, strong enough to remove even wet snow and ice. Angel-Guard’s promotional material states, “The lightweight and easy-to-maneuver broom eliminates the need to climb ladders, a major safety hazard. You can clear snow from your vehicle while standing safely on the ground. It’s perfect for a variety of vehicles, including box trucks, cargo vans, travel trailers, and school buses. The RoofBrum also makes it easy to comply with the law since, in many states, it’s illegal to drive with snow on the roof of a vehicle.” The RoofBrum sells for $89 from their Massachusetts warehouse via UPS Ground.

Contact: FARM SHOW Followup, Angel-Guard Products, 120 Goddard Memorial Drive, Worcester, Mass. 01603 (ph 800-325-4832; [email protected]; www.angelguardproducts.com).

From the archive · Full text
Feature story

This Wrench Gets Into Tight Spaces

Featured source: Pipe Vise, Texas

The newest offering from Texas-based Pipe Vise is the Micro 5, a self-adjusting wrench for small nuts and bolts found in tight spaces.

The Micro 5 is 6 in. long and weighs just over 1/4 lb. The spring-loaded jaw offers several wrench sizes from 5/16 in. to 3/4 in. It has a polished chrome finish, and the handle is contoured for comfort.

The Micro 5 sells for $55 on the company website with free shipping in the U.S.

Contact: FARM SHOW Followup, Pipe Vise (ph 832-303-1149; www.pipevise.com).

From the archive · Full text
Feature story

Easy 4-Way Skid Steer LED Lights

Featured source: Dale McLaen, Rutland, N.D.

You can never have too much light when moving snow with a skid steer at night, but too bright a light can blind others working around you. Dale McLaen solved the problem by attaching LED lights to the front, rear, and sides of his older Bobcat.

“They’re incredibly bright without being blinding,” says McLaen.

“They take very little power to operate, and the side lights let you see all around the machine.

McLaen went online when looking for supplemental lights. He found Auxbeam brand 18W front and rear lights at $25 per pair. For the side lights, he chose Aukmak Rock Light brand 9W lights. They came in a set of four for $28. All were found on Amazon.

“They’re all weatherproof and only took about 4 hrs. to mount and wire in,” says McLaen.

“The large increase in visibility was worth the small cost.”

Contact: FARM SHOW Followup, Dale McLaen, 13756 Hwy 11, Rutland, N.D. 58067 (ph 701-678-5232).

From the archive · Full text
Feature story

Two-Post Car Lift Saves Garage Space

Featured source: Tool Warehouse Inc.

Tool Warehouse Inc. sells two-post vehicle lifts that allow space-efficient storage in small garages and make it easier to get underneath them for at-home mechanic work. These lifts can eliminate the daily “vehicle shuffle” by preventing cars from parking each other in. While four-post lifts are more common, two-post lifts are gaining traction. They’re mounted into the floor and use metal arms to support the weight of each vehicle. The primary drawback is that fewer supports mean less room for error when using them. The lifts only work if you correctly identify the right lifting points, which vary between vehicles. In other words, they require more precision to use. Two-post car lifts also need a sturdy floor for installation - usually at least 4 to 5 in. thick. A car lift installer can check first to ensure the concrete is thick enough to handle the lift’s weight. Four-post lifts, in contrast, require less precision, as all four vehicle wheels are supported by a post of the lift platform. However, they give less access to the vehicle’s underside and consequently won’t work as well for at-home repairs. They also weigh significantly more and can be a challenge to install. The TWI Proline Service Storage two-post lift supports up to 6,000 lbs. with a lifting height of 85 in. It’s a standard two-post chain-over cylinder operation built with a solid platform for easy parking. The handheld pendant control allows users to raise and lower the lift, and safety latches come with electronic limit switches. It’s powered by 220v or 2.2 hp. and has chain equalization for superior stability. Overall dimensions are 130 7/8 in. high, 104 in. wide, and 2,700 lbs. You can purchase the lift from the company website for $4,999.99. Note that you might need to upgrade your garage to handle the TWI lift’s 220V motor. Four-post lifts are also available, starting at $6,399. Contact: FARM SHOW Followup, Tool Warehouse Inc. (ph 877-722-4260; [email protected]; www.toolwarehouseinc.com).