Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 23, No. 1 (1999)

Vol. 23, No. 1 (1999)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 38–40

36 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Nathaniel Regier

Nathaniel Regier, Newton, Kan.

“I re-worked the hood on my 1978 Ford F-350 1-ton pickup so it tilts forward for easy service. I can stand right beside the engine to work on it. I just grab hold of the original latch on front of the hood and pull it down. My technique works well on Ford F series pickups made from 1971 to 1979 but I think the idea would work well on many models. I cut the hood just in front of the windshield. A pair of chains keep the hood from flipping forward all the way over. The chains have springs on them so when the hood goes up it doesn’t stop with a ‘jar’. I made the hinge out of two rubber supports and mounted them under the grill and above the bumper. The radiator was originally bolted onto a steel housing behind the grill. I had to build a steel frame for the radiator so that it stays with the pickup frame as I raise the hood.”

From the archive · Full text
Reader shop tip

John Out

John Out, Enderby, B.C., Canada

“My 10-ft. 6-in. Deere 1360 rotary mower-condi-tioner is equipped with six cutting discs. Three of the discs rotate in one direction and the other three rotate in the opposite direction. When the discs wear out, I switch each one with the one next to it. The discs wear only on one side so this allows them to wear on the other side. As a result I get twice as much life out of the discs without needing to buy new ones, which sell for more than $100 apiece (Canadian). I think the same idea would work on any brand mower-condi-tioner.”

From the archive · Full text
Reader shop tip

Richard Martin

Richard Martin, Burton View, Ill.

“My portable shop table has provided years of valuable service. It’s equipped with two angle iron legs on back and a single steel caster wheel on front which makes it easy to move around. It’s light enough to move about on our concrete shop floor, yet is built heavy enough to support a 6-in. vise and to serve as a portable welding surface. It’s 3 ft. high and has a steel top that’s 1 1/2 ft. wide by 2 ft. long. A pair of shelves under the top can be used to store materials. A pair of 2 3/4-in. long pipes mounted two thirds of the way up the legs serve as handles when moving the table around.”

From the archive · Full text
Reader shop tip 1 of 3

Bill White

Individual tip 1 of 3 from this reader’s published contribution.
Bill White, Twisp, Wash.

“A very good backyard mechanic told me that you can tighten up a slightly loose bearing with Lok-Tite. It takes up about 10 thousandths of an inch. All you do is thoroughly clean the surface where the bearing race goes intothe housing. (Starter fluid is a great cleaner). Then apply Lok-tite generously to either the race or the housing. Slide in the bearing race and let dry completely for a day. I tried it and it really did work on the wobble gear on my swather.

From the archive · Full text
Reader shop tip 2 of 3

Bill White

Individual tip 2 of 3 from this reader’s published contribution.
Bill White, Twisp, Wash.

“I used to use belt dressing by the case when cutting heavy hay. My dad put me onto roofing tar. Two or three finger blobs will smear all over and makes the whole belt grippey for 10 times as long as regular belt dressing.

From the archive · Full text
Reader shop tip 3 of 3

Bill White

Individual tip 3 of 3 from this reader’s published contribution.
Bill White, Twisp, Wash.

“I think the only way to mount a bench vise is on a pedastal mounted on an old truck rim for a base. A vise must be moveable. When I see a shop where the only vise is mounted on the workbench, I know the guy doesn’t do much mechanical work.”

From the archive · Full text
Reader shop tip 1 of 2

Larry D. Rudolph

Individual tip 1 of 2 from this reader’s published contribution.
Larry D. Rudolph, Lost Springs, Kan.

“We put six or seven 8-ft. railroad ties in the rear bed of our pickup for better traction in winter. It forms sort of a second floor. We can still carry bales, sacks and other equipment on top. We slide the tires off onto a 50-gal. drum laying down. One person can load and reload them this way.

From the archive · Full text
Reader shop tip 2 of 2

Larry D. Rudolph

Individual tip 2 of 2 from this reader’s published contribution.
Larry D. Rudolph, Lost Springs, Kan.

“Another idea that we use is putting equipment, bales and other materials on old tractor tires laying flat on the ground. It’s an easy, low-cost way to keep things off the wet ground.”

From the archive · Full text
Reader shop tip

Dan Brown

Dan Brown, Christoval, Texas

“I’ve developed a device that screws onto an outside water faucet that lets you inject air into the faucet to prevent freezing in winter. I call it a Freeze Prevention Connector and it simply screws onto any out side faucet. You attach an air hose, open the water valve, and pump in enough air to push the water back into the building or under the ground. Then close the water valve. When you need water again, all you have to do is open the valve and the air will come out ahead of the water.

“This eliminates the need to shut off the water inside the building, or to drain the pipes.

And eliminates the need for freeze-proof valves.

“I have a patent pending on the device and hope to put it on the market soon.”

Contact: FARM SHOW Followup, Dan Brown, Texas Gems, P.O. Box 555, Christoval, Texas 76935 (ph 915 255-2254).

From the archive · Full text
Reader shop tip

Edward Curry

Edward Curry, Youngstown, Alberta

“I had trouble unloading heavy bales with my slide-in Dew Eze bale fork that mounts in the back of my pickup. This is an older model that is otherwise a very serviceable unit. Rather than buy something new, I modified it so it can handle bigger bales.

“I installed a lift assist cylinder underneath the main beam. The ram pushes against a re-inforced socket welded to the bottom of the main beam. It provides extra lift until the arms are almost straight up and then the regular hydraulics are sufficient.

“The assist cylinder is plumbed single acting into the lift circuit. The cylinder is a standard 3 by 8-in. ram which pins to mounts on the lower frame. The ram adds extra lift when unloading and cushions the drop when loading.”

From the archive · Full text
Reader shop tip

Carl Kulchyski

Carl Kulchyski, Van Anda, B.C.

“I thought other FARM SHOW readers might be interested in this foot-powered metal lathe that I’ve got in my basement. It was patented in 1876 and built by the A.R. Williams Machinery Co. of Toronto, Canada, although the frame has Rockford, Ill., stamped on the side. It has three pedals and an implement seat that slides back and forth, depending on what end of the lathe you’re working on. It’s in good working order even though it was used for years in one of the old isolated ship-yards on the British Columbia coast in Canada.”

From the archive · Full text
Reader shop tip

Scott Ibeling

Scott Ibeling, Aplington, Iowa

“There’s still a tremendous need for this power steering kit since there’s still so many of these pickups in operation,” says Scott, who makes a kit that solves all power steering problems on Ford 4-WD pickups from 1967 to 1977.

“Ford’s ram assist power steering used during those years has been plagued with per-petual problems.”

Ibeling says a sensing valve, which directs power to a hydraulic cylinder, often causes problems. Ford no longer makes repair parts. He sells a conversion kit with an integral power steering box for the pickups. The kit fits all Ford 100, 150, and 250 pickups from 1967 to 1977, whether they were equipped with manual or ram assist power steering. The kit consists of adapter plates, hardware and a special bit to drill the steering column, and the steering box. You remove the steering box and weld in adapter plate, then replace with included steering box.

Contact: FARM SHOW Followup, Scott Ibeling, 1014 Parrott St., Aplington, Iowa 50604 (ph 319 347-2491).

From the archive · Full text
Reader shop tip 1 of 5

Craig Froman

Individual tip 1 of 5 from this reader’s published contribution.
Craig Froman, English, Ind.

“I keep a bunch of golf tees in my toolbox for closing fuel or vacuum lines while during repairs. I also save all the plastic plugs and covers that come on new hydraulic hoses and fittings in order to put over hoses when doing repairs to keep out dirt and moisture. Small ones are especially useful for diesel injection pumps and lines.

From the archive · Full text
Reader shop tip 2 of 5

Craig Froman

Individual tip 2 of 5 from this reader’s published contribution.
Craig Froman, English, Ind.

“When I have to change engines on a mower - push or riding - I turn the mower upside down and weld the engine bolts to the frame (unless it’s aluminum or die cast) and take the nuts off on the top. Thereafter it’s a lot easier to take the engine off for repairs.

From the archive · Full text
Reader shop tip 3 of 5

Craig Froman

Individual tip 3 of 5 from this reader’s published contribution.
Craig Froman, English, Ind.

“Damage to inner tubes by rusty tractor rims can be avoided by wrapping the rim with duct tape. It will seal them up. It’s best to put two layers and make sure it’s smooth with no wrinkles.

From the archive · Full text
Reader shop tip 4 of 5

Craig Froman

Individual tip 4 of 5 from this reader’s published contribution.
Craig Froman, English, Ind.

“I made a bracket to hold my large Handy Man jack on the back of my tractor. Now I always have the jack with me in the field or when building fence. Real handy for a lot of jobs.

From the archive · Full text
Reader shop tip 5 of 5

Craig Froman

Individual tip 5 of 5 from this reader’s published contribution.
Craig Froman, English, Ind.

“You can make a paper towel holder for the shop or garage using a heavy wire coat hanger. Just cut one corner and make a couple of interlocking hooks. They also work well to hold rolls of tape, hose clamps, small bearings, etc.”

From the archive · Full text
Reader shop tip

Walt Behrens

Walt Behrens, Minot, N. Dak.

Walt’s company, Behrens Construction & Mfg., re-cently introduced this new patent-pending roller that attaches to the fence of a table saw to hold wood securely in place.

The “Roller Holder” consists of an 8-in. long by 2 1/2-in. dia. smooth PVC roller and 10 in. long steel arm. The roller turns on lubrication-free nylon bearings on the arm and the arm attaches to the table saw fence with a C-clamp. You position the roller as close to the blade as possible.

Sells for $24.95 plus $4 S&H. Contact: FARM SHOW Followup, Behrens Construction & Mfg., 7110 Co. Rd. 15 West, Box 227, Minot, N. Dak. 58703 (ph 800 659-1268 or 710 839-5643).

From the archive · Full text
Reader shop tip

Stanley Spohr

Stanley Spohr, Avilla, Ind.

“The best slag hammer I’ve ever used consists of half a combine sickle guard welded to a 1-ft. long, 3/4-in. dia. rod.

“The guard is made from a real hard material that’s ideal for knocking slag off welds. I’ve never had to sharpen it in the three or four years I’ve used it, unlike commercial slag hammers I’ve used in the past.

“It cost nothing to make and works like a charm.”

From the archive · Full text
Reader shop tip

Glen Thompson

Glen Thompson, Traer, Iowa

Glen came up with a low-cost effective way to keep water from leaking into the auger ports on his grain bin.

“I have a 6,000 bushel drying bin with three 4-in. dia. augers that go through the roof to storage bins. The flex of the roof often allows water to leak around the augers, damaging them when it freezes.

“I found that using spray-on Styrofoam insulation, the kind you buy for $3 or $4 a can at any hardware store, solves this problem. You simply apply the insulation 2 or 3 in. above the auger in a horseshoe shape that’s bigger than the auger itself. This forms a di-version above the roof to stop the leak.

“I tried this on one auger a couple years ago and it worked so well I did the same to the other two the following year. Just for looks, I’ve trimmed up the excess insulation with a knife and painted it to match the bin. You can make diversions for three or four augers and have half a can of insulation left.”

From the archive · Full text
Reader shop tip

Rodney D. Reese

Rodney D. Reese, Port Matilda, Pa.

After mounting a Gandy applicator on his Case-IH 8750 forage harvester, Rodney decided to make the applicator, which he uses to apply granular inoculant, automatic rather than manual.

“I mounted an industrial switch (Allen-Bradley 800T-B6B) under the upper feed roll on my forage harvester to operate the two-tube drop applicator. The applicator, which has extensions for a total capacity of 100 lbs., mounts ahead of the cutterbar and behind the feed roll to drop inoculant on silage as it enters the cutterhead.

“I used a regular trailer plug between the tractor and machine to supply 12-volt power. A pilot light in the tractor cab monitors operation.

“When silage raises the upper feed roll, the switch is on and the applicator runs. When the feed roll is down, the switch goes off and so does the applicator. That way, you’re only running the applicator when material is coming into the machine so you’re applying in-oculant more evenly than if you were controlling the operation by hand.

“This principle would work on any forage harvester. Any industrial ‘normally on’ switch, which you can buy at a good electrical supply company, would work.”

From the archive · Full text
Reader shop tip

Fred Lewton

Fred Lewton, Valley Grove, W. Va.

“I had rotator cuff surgery on my right shoulder in 1988, which made it even more troublesome than usual to reach behind me to operate the manual tie arm on my Massey Ferguson 560 round baler.

“So I came up with a ‘poor man’s’ automatic tie system from a variety of old parts I had around the shop. It cost nothing to make yet works as well as comparable after-mar-ket or optional factory-built systems that cost hundreds of dollars.

“I used a 12-volt rear window motor out of a 1978 GMC Suburban. I used two U-bolts to mount the electric motor on the 1 1/2-in. dia. bar which runs from one side of the baler to the other and on which the manual tie arm pivots. I welded a piece of 1-in. dia. rebar, which I bent into a 90 degree angle, into the eyelet that originally held the rope that engages and disengages the tie arm. The rebar extends the arm so that travel is exactly 70 in., enough to tie my 60 in. long bales.

“I next ran electric wires back inside the tractor cab along the hydraulic lines and connected them to the window motor switch which I mounted inside a 2 by 4-in. metal electric box. I simply mount the box wherever it’s handy in the cab with a magnet.

“Now, the only manual operation in baling remains cutting the twine. Saves a lot of time and aggravation, and a lot of strain on my shoulder.”

From the archive · Full text
Reader shop tip

Roland Schild

Roland Schild, Greenfield, Ill.

Roland mounted a big fluorescent light on top of his 10-ft. long shop boom to provide light for working outside at night.

“The boom swings outside of the door and the light shines right over the work area,” he says.

“Somebody gave me an old 4 by 6-ft.

tire sign that I covered with masonite on one side. I painted the masonite white to reflect light and mounted the sign on 4-ft. high pipe legs above the boom which is made of 5-in. H beam.”

From the archive · Full text
Reader shop tip 1 of 2

Roger Wessels

Individual tip 1 of 2 from this reader’s published contribution.
Roger Wessels, Fairbury, Ill.

Roger is hard-pressed to explain why the axle frame on his Deere 7700 combine, as well as those on the 6600, 6620 and 7720 series, are 2 in. farther to the left of center on the right side than on the left side.

“I can tell the difference in the way they steer, which isn’t as straight,” he says.

“Deere’s approach to the problem was to sell the customer a 2-in. spacer to install on the right wheel rim. Why they did so is beyond my understanding.

“I modified the axle frame on my combine by making two heavy-duty face plates that install on each side of the axle to spread out wheels equidistantly to exactly 120 in. I had them cut out of 1-in. thick plate at The Farm Shop (P.O. Box 36, Congerville, Ill. 61729; ph 309 448-2338). I drilled out the spacer blocks between the two plates. They’re heavier built and cost less than comparable Deere extension brackets, and they work great to improve handling.”

From the archive · Full text
Reader shop tip 2 of 2

Roger Wessels

Individual tip 2 of 2 from this reader’s published contribution.
Roger Wessels, Fairbury, Ill.

Roger also retrofitted the drive wheels on his 7700 with a pair of Alliance 12-ply knobby tires from Harry’s Farm Tire Service (Jackson St. Place, Wheatland, Iowa 52777; ph 319 374-1253).

“The reason for doing so was to reduce lug tracks from the combine and, thus, cut down on vibration in the cab of my 4640 when V-ripping bean ground after I combine,” he says.

Shop feature stories

From the archive · Full text
Feature story

MIG And Stick Welder Rolled Into One

Featured source:

This new combo welder lets you do both stick welding and wire feed welding with one machine.

The Gunslinger has 260-amp MIG power with built-in 150-amp stick welding capability, allowing you to use one machine to do both stick and wire feed welding. It costs less than the price of some conventional MIG-only machines, says the company. It delivers a full 40 percent duty cycle at 260 amps compared with the lower duty cycles of some 250 amp MIG-only machines. Its maximum wire speed is one of the highest in its class, says the company.

Welds up to 1/2-in. thick metal. Sells for $1,550. Contact: FARM SHOW Followup, Panasonic Factory Automation, 9377 West Grand Ave., Franklin Park, Ill. 60131 (ph 888 726-9353; fax 847 288-4564).

From the archive · Full text
Feature story

Rolling Stairway Handy In Shop, Farmyard

Featured source:

An Illinois farmer bought a set of metal stairs when a local manufacturer went out of business and reworked them for use in his shop, mounting them on wheels and adding a 4-ft. square platform on top.

John Imhoff, Roanoke, Ill., says the rolling stairway provides him with easy access to any part of his 50-ft. sq. shop. It can also be rolled outside to put the tarp on his semi truck, etc.

“Climbing up the stairway is a lot easier than climbing up a ladder and it’s easy to roll around,” says Imhoff, who credits employee Dave Kindig (pictured) for most of the modifications made to the stair-way.

“I use it often to access a balcony on one side of my shop where I store parts. I also use it to change light bulbs in the shop ceiling.”

The stairway originally was equipped with a pair of vertical steel legs on back. However, mounting a platform on top re-quired support so Kindig cut off the legs and repositioned them at an angle. The legs are braced by a pair of criss-crossed steel rods. Wheels at the back mount on a pivoting axle made from steel tubing. It pivots from side to side so that all four wheels carry an equal load on uneven ground. To reduce any danger of tipping, threaded adjustment cranks can be used to tighten down either end of the axle and make it rigid.

The platform at the top of the stairway consists of a metal frame covered by plywood.

Contact: FARM SHOW Followup, John Imhoff, RR 2, Box 52, Roanoke, Ill. 61561 (ph 309 923-7345).

From the archive · Full text
Feature story

“Roller Chain Ruler” Takes The Guesswork Out Of Broken Chain Repairs

Featured source:

If you’ve ever had to replace a broken chain roller, you know it can be a pain to get the chain sized right. This new “Roller Chain Ruler” has pegs on one side that hold the chain in place and large numbers on both sides of the ruler that tell you how many chain links you’ll need. The ruler can also be read in millimeters and inches.

“It’s a lot faster than counting individual links and also eliminates the possibity that you’ll miscount the links,” says Kent Zimmerman, John Day Co., Omaha, Neb.

The ruler is made from recycled plastic so it isn’t affected by gas, solvents, or oils. A hole at each end of the ruler lets you hang it from a wall or mount it on a bench. Comes in a set of three different rulers for No. 40, 50, and 60 chain.

Sells for $35 plus S&H. Contact: FARM SHOW Followup, John Day Co., 6263 Abbott Drive, Omaha, Neb. 68110 (ph 800 767-2273 or 402 455-8000; fax 402 457-3811) or Roller Chain Ruler, Rt. 1, Box 85, Elbow Lake, Minn. 56531 (ph 218 685-4604).

From the archive · Full text
Feature story

Oil Saver Empties Quart Bottles

Featured source:

Every last drop of motor oil out of plastic quart bottles can be collected with this new recovery unit that can be set up on your workbench or hung from your shop or garage wall.

It consists of a plastic collection unit that holds five 1-qt. bottles upside down so that every last ounce of hard-to-get oil drains out. The oil runs down a channel to another quart bottle positioned below.

Sells for $7 plus $5 S&H. Contact: FARM SHOW Followup, Auto Accessories of America, Route 322, Box 427, Boalsburg, Pa. 16827 (ph 800 458-3475 or 814 364-2141; fax 9615).

From the archive · Full text
Feature story

Rotating Mitre Band Saw

Featured source:

The head on this rotating mitre band saw can be moved left or right up to 45 degrees, allowing you to switch to a different cutting angle in seconds, says Ellis Mfg., Verona, Wis.

The two-wheeled Ellis 1600 is equipped with a 1-in. wide blade and is powered by a 1 hp, 110-volt electric motor. The turntable mounts on a half-moon casting. A built-in protractor allows for fast and accurate selection of angles, and a movable guide arm can be used to make the cut as accurate as possible.

Unit mounts on 10-in. wheels and has legs that are adjustable for height.

Sells for $2,395 plus S&H. Contact: FARM SHOW Followup, Ellis Mfg. Co., Inc., Box 930219, Verona, Wis. 53593 (ph 800 383-5547).

From the archive · Full text
Feature story

Shop-Built Bandsaw

Featured source:

“I made it because the commercial models I looked at were either too small for my needs or so big I couldn’t justify the cost,” says Stan Weichel about a bandsaw he built for his metal-working shop where he custom-builds specialty equipment.

The Odessa, Sask., farmer’s design incor-porates some features not even found on big commercial saws that cost $4,000 or more.

“For example, it has adjustable saw guides which you adjust with set screws so you can square the blade back again,” Weichel notes.

“They’re made of 2 by 2-in roller bearings and allow me to move the blade up or down 3/16 in. or 1/4 in. to the left or right.”

Weichel’s saw mounts on a 26-in. high, 4-ft. long steel table. Two of the legs have wheels so it’s easy to move around.

A 20-ga. hinged steel cover shields the blade and other working parts of the saw.

The commercial high-speed Matrix blade is 3/4 in. high by 0.035 in. wide by 106 in. long. It’s driven by two pulleys and a gear-box from a 3/4 hp electric motor mounted on one side of the table.

It easily handles up to 7 in. high by 12 in. wide steel, Weichel says.

“I’ve used it to cut hundreds of meat bandsaws that I make as well as snowmo-bile and livestock trailers,” he says.

Out-of-pocket expense was $1,000 (Canadian).

Contact: FARM SHOW Followup, Stan Weichel, Box 51, Odessa, Sask., Canada S0G 3S0 (ph 306 957-2043).

From the archive · Full text
Feature story

Low-Cost All-In-One Metal Fabricator

Featured source:

“Comparable machines cost four times as much,” says Mike Nimmo about the “All-In-One Fabrication Shop,” a compact metal-working tool with 40 tons of power.

Powered by a 110-volt 3/4 hp motor, it can punch, shear, notch, bend, form and press.

The shear can handle flat, round, square and angled steel up to 3/8-in. thick and can be switched to an 8-in. brake that’ll bend steel up to 1/4 in. thick.

The 40-ton punch has a 3 3/4-in. deep throat and can punch a 1-in. dia. hole in 3/8-in. steel. It’s capable of four to six strokes per minute.

Options include a variety of punches and dies, a heavy-duty notcher attachment and a pipe notcher.

Sells for under $2,500. Contact: FARM SHOW Followup, METALpro Ironworkers, 1320 Plainfield Avenue, Janesville, Wis. 53545 (ph 800 558-1345 or 608 758-1345; fax 1272).

From the archive · Full text
Feature story

Compact Bender

Featured source:

“It’s becoming one of the most popular tools among both professional and hobbyist metal workers because of its ultra-compact size,” says the manufacturer of the “Compact Universal Pipe Bender.”

Weighing only 60 lbs. and standing just 38 1/2-in. high, the “Compact Bender” has the capacity to bend up to 5/16 by 2-in. flat steel, 5/8-in. solid round or solid square hot rolled mild steel. A sharp right angle bend attachment (included) bends up to 3/16 by 2-in. or 1/4 by 1 1/4-in. flats. Includes seven 1 to 3-in. heat-treated steel dies, die rack, square stop block, heat-treated pins, stand, sharp right angle bend attachment, and instruction manual.

Sells for $398; S&H included in U.S. Contact: FARM SHOW Followup, Shop Outfitters, 605 South Adams St., Laramie, Wyo. 82070 (ph 307 745-5999; fax 742-5999).

From the archive · Full text
Feature story

Hydraulic Presses

Featured source:

Cottonwood Welding’s new Black Max hydraulic press is built tough and comes in three models with 50, 100, and 125-ton capacities. The 50-ton model has a 12-in. cylinder stroke and a self-contained hydraulic system equipped with a 2-speed hydraulic pump; 6-position bed height adjustment; an open-ended frame for long parts; press blocks and V-blocks as standard equipment; and 2-in. bed pins with hardened holes. It uses single phase electricity; 3-phase is optional. The 100-ton model is 86 in. high and 64 in. wide and has a maximum working width of 48 in.

“The bed is hydraulically raised or lowered on all models. A pressure gauge is standard equipment.

“The 50-ton model sells for $3,250; the 100-ton model for $4,595; and the 125-ton model for $5,295. All prices are F.O.B. Cot-tonwood, Minn.

Contact: FARM SHOW Followup, Cot-tonwood Welding & Machine, Inc., Box 15, Cottonwood, Minn. 56229 (ph 507 423-6666; fax 5609):

From the archive · Full text
Feature story

Full Range Of Iron Workers

Featured source:

“We offer 18 different iron workers ranging from 42 to 150 tons in capacity. They all have a ‘guillotine’ action that cuts cleaner and more evenly for the full length of the cut. Other machines use a ‘scissors’ action which loses force at the far end of the blades and causes greater metal defor-mation. Our iron workers can also be used to cut, bend, punch, notch, and work on flat stock, round bars, and angle iron.

“The 42-ton model sells for about $5,000 plus S&H and the 150-ton model for about $30,000 plus S&H.”

Contact: FARM SHOW Followup, MLM Enterprises, 13307 525th Ave., Cos-mos, Minn. 56228 (ph 800 737-7975).