Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 22, No. 3 (1998)

Vol. 22, No. 3 (1998)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 28–30

29 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Rockmount Research & Alloys, Inc.

Rockmount Research & Alloys, Inc., Box 2909, Vancouver, Wash. 98668 ph 206 254- 2020)

“We’ve come up with a way to re-move broken bolts and studs quickly and easily without using special equipment. The stud extraction procedure requires our Brutus electrode, a nut, and a washer. The Brutus electrode has a non-conductive coating that eliminates side arcing. It can be used on tool steel, stainless steel and hardend steel.

“You center the electrode rod in the hole and strike the arc on the broken stud. Maintain a very close arc with the rod contacting the center of the weld puddle. For horizontal situations strike and hold the arc slightly above center, without using a circular or weave technique. Allow the weld deposit to build up slowly to form a ‘nub’ just below the housing surface. The slag will flow to the sides, protecting the side walls.

“Allow the buildup deposit to cool, then chip the slage off the top ‘nub’ of the weldment. Select a flat washer that’s smaller than the stud hole and place it over the hole. Place a nut on the washer and continue buildup into the nut. After weldment is built up above the hole surface, angle the electrode slightly to weld the nut and washer to the weldment.

“Allow the assembly to air cool. Using a hand wrench, you can now back out the nut and broken stud.”

From the archive · Full text
Reader shop tip

Larry Johnson

Larry Johnson, Colo, Iowa

“When I harvest my crops I sometimes have to travel up to 30 miles from home. Instead of driving the combine home every night, I keep it in the field overnight and use a 120-gal. diesel fuel barrel, mounted on a trailer, to refuel it. Using a trailer keeps the mess of diesel fuel out of the pickup, and leaves the pickup free for other jobs. A chain and binder secures the barrel to the floor. I mounted a 12-volt electric fuel pump on the barrel and use alligator clips to hook it up to the battery in my pickup or combine.”

From the archive · Full text
Reader shop tip 1 of 2

Robert Crampton

Individual tip 1 of 2 from this reader’s published contribution.
Robert Crampton, Staples, Minn.

“I have three public roads going by my farm and often have trouble with hunters who tres-pass on posted land and scare my cattle. Some have even turned their dogs loose on my farm which drives the cattle away. One time I was driving around my farm and saw some guys with a dog kennel on back of their pickup. They said they were hunting for coyotes and that they would shoot them without walking on my land. However, I have trouble with gophers so I don’t want the coyotes killed. There have been confrontations, and one time I even had someone pull a gun on me. Most øf the time I’m alone so if I do complain to the sheriff it’s my word against the word of two or three hunters.

“That’s when I came up with the idea of using a telescoping video camera as a witness. I mounted the camera on a tripod on an old refrigerator tray on the passenger side of my pickup seat. I plug the camera into the pickup’s cigarette lighter, The camera zooms in and can also be swiveled up or down. Now I can videotape any problem situations to show the sheriff as proof.”

From the archive · Full text
Reader shop tip 2 of 2

Robert Crampton

Individual tip 2 of 2 from this reader’s published contribution.
Robert Crampton, Staples, Minn.

“Here’s another idea; To keep mice from entering my buildings in the fall, I buy chunks of mouse bait in 1-gal. pails from a local store. I cut a 1-in. dia. hole in the side of the pail where mice can enter and eat the bait. The pails are sold with four or five chunks of bait in them. I usually keep three chunks in each pail and put the rest of the chunks in 1-gal. ice cream pails which I also cut holes into. I have a half dozen of the pails around my house and also inside my barn and shed. Buying bait in volume this way is much less expensive than using cardboard bait boxes and the pails keep bait safe from pets and kids. A brick placed on top of each pail keeps the wind from blowing them around.”

From the archive · Full text
Reader shop tip

Ben Larison

Ben Larison, Mondamin, Iowa

“The engine on my 20-year-old International small square baler was originally designed to be started by hand cranking it. I made a self-starter for the engine by drilling a flywheel ring off a Chevrolet automatic transmission and bolting it to the engine’s belt drive pulley, then making a bracket to mount a 12-volt AC starter off an old Chevy car. The starter turns the flywheel ring which cranks the engine.”

From the archive · Full text
Reader shop tip

Ryan Feige

Ryan Feige, Astoria, S. Dak.

“Two years ago I bought a Deere 4010 tractor equipped with a bad diesel engine for $2,500. The 6-cyl. engine had about 10,000 hours, used oil, and also needed head and injector work. I replaced it with a 6-cyl. turbocharged diesel out of a Deere 7700 combine. It was equipped with a big Bosch fuel injection pump and a water pump that’s bigger than the one on the original 4010 engine (older 7700s were equipped with a smaller Rosamaster injection pump and a smaller water pump just like on 4010s).

“To overhaul the original engine would’ve cost $3,000 to $3,500. It had 380 cu. in. and wasn’t turbocharged. The new engine has 404 cu. in and is turbocharged, giving it 140 hp compared to 80 before. There’s no visual difference but the tractor has a lot more power. Also, the new engine has only about 3,500 hours so it’s almost like starting out with a new engine. I paid $2,100 for the engine. I’d do the same thing again without hesitating.

“I borrowed the frame rails from a Deere 4320 tractor to make room for the fan on the new engine’s water pump. I had to lengthen the hood 4 in. so that the turbocharger would fit and also put in a new clutch and bell housing. The bell housing bolted right up.”

From the archive · Full text
Reader shop tip

Patrick Mahoney

Patrick Mahoney, Singerman Labora- tories, Murrysville, Penn.

“We’re a distributor for an amazing new corn oil-based hand cleaner that can be used with or without water. SavvySoap really cleans great. It can remove ink, grease, and paint and works better than toxic chemicals. You simply rub it into your skin and wipe it off with a cloth if water isn’t available. The product contains lanolin so it doesn’t crack the hands or smell bad. It’s totally biodegradable and, because it’s corn oil-based, it doesn’t create hazardous waste or water pollution.

“ “SavvySoap comes in a 1-gal. flat top container equipped with a pump. Sells for $17.95 per gal. A steel wall rack for the 1-gal. size sells for $7. Other sizes are also available.”

Contact: FARM SHOW Followup, Patrick Mahoney, Singerman Laboratories, 4091 Saltsburg Road, Murrysville, Penn. 15668 ph 800 798-7986; fax 412 798-0450).

From the archive · Full text
Reader shop tip 1 of 2

Universal Sales

Individual tip 1 of 2 from this reader’s published contribution.
Universal Sales, Box 55, McLeod, N. Dak. 58057 ph 701 439-2766

“Our new ‘Centipede’ socket holder holds sockets better than any other holder on the market. The polyurethane rail that holds the sockets is impervious to rust, corrosion, chemicals, and solvents and will bend even in cold weather. The rail is so flexible that you can bend it completely over and test a socket for size before removing it from the holder. Even when it’s loaded with sockets you can hang it, roll it, twist it, lay it flat, or throw it in your toolbox. A patented locking design holds the sockets in place. The rails hold 1/4, 3/8, or 1/2-in. sockets.

“The 1/4-in. model sells for $5, the 3/8-in. for $6, and the 1/2-in. for $7. The 3/8 and 1/ 4-in. sets together sell for $10, and a full set of all three models sells for $16. Add $4 for S&H.

From the archive · Full text
Reader shop tip 2 of 2

Universal Sales

Individual tip 2 of 2 from this reader’s published contribution.
Universal Sales, Box 55, McLeod, N. Dak. 58057 ph 701 439-2766

“We also sell tap and die sets - one with standard size taps and dies and the other with Metric. They’re made from Tungston tool steel alloy. Each set sells for $199 or you can buy them both for $375. Add $10 S&H per set.”

From the archive · Full text
Reader shop tip

Randy Mittlestadt

Randy Mittlestadt, Audubon Tractor Parts, Audubon, Iowa 50025 ph 800 831- 5730

“Our TSR replacement straw chopper for Deere combines sells for about one third less than the Deere factory price. It’s designed and built to exact standards and will bring your chopper back to original performance specifications. Besides offering complete straw chopper assemblies, we also offer a full line of straw chopper parts for Deere combines built since 1970. In Canada contact Dan Poss, Rempel Tractor Parts, Niverbille, Manitoba, Canada ph 800 244-7662.”

From the archive · Full text
Reader shop tip

Central Supply & Rubber Co.

Central Supply & Rubber Co., 109 North 9th St., Omaha, Neb. 68102 ph 800 444-8666

“You can jump start any vehicle without the need for jumper cables or another vehicle using our new Jump-N-Carry. The portable unit has its own battery and jumper cables and comes in a one-piece molded case. It provides 12-volt DC power or portable 110/ 120-volt AC power (for portable AC power an inverter is required, allowing the unit to operate TV’s, shop tools, etc.). It has 400 amps of cranking power. Two recharging methods can be used. Simply turn off the ignition key, connect the jumper cables, and start the vehicle. Or, turn off the ignition key, plug an optional male-male cord into a vehicle’s cigarette lighter, wait several minutes and start the vehicle. A battery status gauge indicates power available and when to recharge.”

From the archive · Full text
Reader shop tip

Clair & Warren Wilson

Clair & Warren Wilson, Winchester, Ill.

They recently bought a huge bridge crane from a railroad repair company to install in the 120 by 60-ft. shop they built out of an airplane hangar (featured in FARM SHOW’s Vol. 21, No. 6). The big railroad crane will fit nicely in the large shop.

They towed the crane home from a salvage yard in two pieces by equipping it with rear wheels and a heavy hitch in front. (C.F. Marley, Nokomis, Ill.)

From the archive · Full text
Reader shop tip

Larry Stephen

Larry Stephen, Martinsville, Ill.

He turned an old forklift mast into a heavy-duty shop elevator by mounting it along one wall and building a platform onto the mast in place of the forks. He uses it to ride up to the upper level of his shop. The elevator is controlled by electrically-powered hydraulics so a simple electric switch is used to move it up or down. Makes it easy to retrieve parts or other equipment from the upper storage area.

From the archive · Full text
Reader shop tip

Jim Rogers

Jim Rogers, Port Orford, Ore.

“You can keep gasoline fresh in unused machines with two commercial products that keep it from deteriorating. The most widely known is Stabil, which can be purchased at Wal-Mart and other stores. A small container of Stabil costing $3.97 will preserve 20 gallons while the larger container costing $8.97 treats 80 gallons. The company says it will keep fuel fresh for at least 5 years and much longer if the fuel is kept in sealed cans in a cool place.

“Another product called Gas Saver Plus is available by mail order. A $15.95 supply (plus $5.95 shipping) treats 160 gal. A $27.95 bottle treats 320 gal. Phone numbers for a couple of the mail outlets are 800-866-4876 or 303 277-0305.

“These products are ideal for any machine that sits around unused for long periods of time, such as as an emergency generator.”

From the archive · Full text
Reader shop tip

Brian R. Hebden

Brian R. Hebden, Springville, N.Y.

“I have easy access to my tools thanks to this pull-out tool tray which I built into the back of my pickup. The tray slides in and out of the bed. I used 2 by 4’s and a sheet of 4 by 8-ft. plywood to make the tray. Garage door hangers and caster wheels underneath the tray make the tray easy to roll out. I installed hold-down rails on the wheel wells or a center-mounted leg to keep the tray from tipping whenever it’s pulled out. At the job site I simply open the pickup’s tailgate and pull the tray out. The tools are easy to reach from all sides.”

From the archive · Full text
Reader shop tip

Ken Schultz

Ken Schultz, Chicago, Ill.

“Dad and I started using 2 and 3-lb. coffee cans for bolt storage a couple years ago after our garage burned down. We had stored bolts in cigar boxes, but they burned up in the fire and we had a real mess sorting bolts.

“Coffee cans are first and foremost fire-proof. They also stack easily in tight locations like our wall cabinet. Best of all, they’re free. The labels come off easily so you can use masking tape or duct tape to label them for sizes. We store everything from 1/4-in. dia. to 1-in. dia. bolts in them.”

From the archive · Full text
Reader shop tip

Bill Weston

Bill Weston, Floyd, Iowa

Bill’s company, Wesam Inc., manufactures replacement parts for automatic feeders and unloaders for most makes of vertical silos.

“Our replacement parts generally sell for 20 to 30 percent less than original equipment,” Bill says.

“We make all of the bearings and wear parts that either break down or wear out. Parts include augers and auger knives, wall wheels and wall cleaner assemblies, drive shafts, bushings, blowers and discharge chutes. We also sell new Farm-Eze belt feeders and a full line of belts, 12 to 48 in. wide.

“Our most requested parts are 7 and 9-in. dia. augers. Impeller assemblies could be considered our most unusual parts since every manufacturer has their own idea on how they should be designed and built.”

Contact: FARM SHOW Followup, Wesam Inc., First Ave., Floyd, Iowa 50435 (ph 515 398-2875; fax 2846).

From the archive · Full text
Reader shop tip 1 of 2

Karl Plesums

Individual tip 1 of 2 from this reader’s published contribution.
Karl Plesums, Spooner, Wis.

“I modified our Deere 7000 4-row (36-in.) corn planter so that the casting lips which hold the closing wheel assemblies don’t break when planting rocky ground. That used to happen to us every 40 acres or so but since I modified the planter we’ve broken only two lips in 1,500 acres.

“The problem is that the bolt holding the casting in place behind the downpressure spring on the closing wheel isn’t big enough and is too rigid. I replaced the original 1 in. long bolts with 2 1/2-in. long bolts. I also added a compression spring (the kind used on doorstops) in between the bolt head and the casting so the assembly flexes over rocky terrain.

“This modification costs only a buck or two per row and works like a charm. In fact, it worked so well on our Deere planter I even modified the new Kinze 8-row (30-in.) planter we bought last year before ever taking it to the field. We haven’t broken even one casting on it.

From the archive · Full text
Reader shop tip 2 of 2

Karl Plesums

Individual tip 2 of 2 from this reader’s published contribution.
Karl Plesums, Spooner, Wis.

“Three years ago, on the coldest day of winter, I also came up with an easy way to unplug Big Jim silo unloader chutes. Dad had accidentally plugged the hole down to the bottom conveyor with a frozen chunk of silage. I spent about four hours trying to poke a hole through the mess but to no avail.

“I finally decided to try an ice-type auger. I welded a 2-ft. length of 4-in. dia. flighting to a piece of 3/4-in. dia. black pipe. I used a small pipe wrench to screw the auger through the plug up. It took only about 15 minutes to unplug the mess.

“Incidentally, you can bolt several sections of black pipe to the auger to go through deeper plugs. I’ve since used this to unplug 25 ft. of haylage in about 20 minutes.”

From the archive · Full text
Reader shop tip

John E. Tesch

John E. Tesch, Mervin, Sask.

John and his brother, Adolph, have converted electric motors from worn out pumps into shop bench grinders and cutters.

“Electric motors in damaged pumps are often still good and cost nothing,” says John.

“I converted the first motor about five years ago and it worked so well I just converted another one last winter.

“You simply remove the electric motor from the pump, saving the pump’s impeller shaft to install on the motor’s output shaft. Attach an arbor and washers to the threaded end of the shaft so you can fit a grinding wheel or abrasive wheel on the end.

“I built an open-ended box with a flange on both ends out of 16-ga. sheet metal for a motor housing. I installed an off/on switch in a rectangular hole I cut in the front of the box and wired it to the motor, which mounts inside the box. The box mounts on my work bench on a plate attached to the bottom.

“It looks just like a factory job and didn’t cost more than the $10 or $20 each wheel cost at our local hardware store.”

From the archive · Full text
Reader shop tip

David Green

David Green, Lubbock, Texas

“We manufacture head gaskets for antique and current model tractors, trucks, and stationary engines of any brand. We make them from composites, such as wire inserted asbestos fiber with metal fire rings, or from solid soft annealed copper.

“Our most commonly requested gaskets are for Farmall M, Oliver 88, Deere and McCormick-Deering tractors. We make custom gaskets to fit any engine no matter how rare.

“Prices range from $40 for some 2-cyl. engines up to $380 for some 6-cyl. engines. Our gaskets average in the neighborhood of $75.”

Contact: FARM SHOW Followup, Lubbock Gasket & Supply, 402 19th St., Lubbock, Texas 79401 (ph 800 527-2064 or 806 763-2801; fax 0965).

From the archive · Full text
Reader shop tip

Joyce Dulin

Joyce Dulin, Cordova, Md.

Joyce and her husband, Bunky, operate Antique Gauges Inc., which handles custom-built replacement gauges (temperature, oil pressure, amperage, etc.) for tractors built between the 1930’s and ‘50’s. They’re exact reproductions of originals.

“Our white-faced Deere gauges are our biggest sellers, ranging in price from $35 to $42,” Joyce says.

“Hydraulic pressure gauges for IH tractors are our most unusual, running $47. There’s $5 S&H on all orders.”

Contact: FARM SHOW Followup, Antique Gauges Inc., 12287 Old Skipton Rd., Cordova, Md. 21625 (ph/fax 410 822-4963).

From the archive · Full text
Reader shop tip

Kurt Jacobi

Kurt Jacobi, Anaheim, Calif.

“We custom-build hard-to-find pistons for any engine, import or domestic. We’ve been building pistons for over 80 years and have over 77,000 parts listed in our catalog, ranging in size from 1 1/2-in. dia. up to 10-in. dia.

“Our most commonly requested piston in the ag market is for old Deere G’s and Minneapolis-Molines. Of course, price varies according to size and how much modification is specified, but a standard piston for a Deere G runs about $210.

“At this time, we have a lead time of seven weeks on orders due to the high demand.”

Contact: FARM SHOW Followup, Jahns Quality Pistons, 1360 N. Jefferson St., Ana-heim, Calif. 92807 (ph 800 225-0277 or 714 579-3795; fax 524-6607).

From the archive · Full text
Reader shop tip

Barbara Bland

Barbara Bland, Paris, Ky.

If the clutch lever on your old Deere tractor wobbles side-to-side a couple inches when the tractor idles, you’ll want to check out this “puller” Barbara’s late husband, Jess, invented.

It’s designed for easy pivot pin removal, which can often be tricky.

It consists of two blocks. One has two bolt holes in the ends. The other has a large hole (for the clutch pivot pin head to pass through) and two threaded holes for the puller bolts.

To use, first loosen the large nut on the end next to the tang on the gearbox. Turn the nut until it is flush with the end of the threaded portion of the pivot pin to provide more area for the puller bar to contact. Install the puller with block A contacting the pivot pin nut and block B in contact with the clutch lever so that the head of the pivot pin can pass through the large hole. Slowly tighten the bolts, keeping the bars parallel, until the nut contacts the tang. Remove the nut and push off the rest of the way.

Sells for $29.50 including S&H. Contact: FARM SHOW Followup, Mrs. Jess Bland, 2255 Millersburg Rd., Paris, Ky. 40361 (ph 606 484-3326).

From the archive · Full text
Reader shop tip

Robert Schum

Robert Schum, Saint Meinrad, Ind.

“I made a low-cost workbench by welding a steel I-beam on top of a pair of old steel wheels. I keep the workbench outside my shed. The I-beam is 18 in. high and 10 in. wide, and the wheels are about 30 in. high. It really comes in handy for sharpening Bush Hog or lawn mower blades. I clamp the blades right onto the I-beam and use a portable grinder. The lip of the I-beam comes in handy for storing small parts and keeps them from getting lost. If I ever need to move the workbench I can just pick it up with a front-end loader.”

From the archive · Full text
Reader shop tip 1 of 2

Jack Dyck

Individual tip 1 of 2 from this reader’s published contribution.
Jack Dyck, Richmond, B.C.

“I built my own pto-driven air compressor by mounting a right angle gearbox and pulley unit - salvaged from an old tractor- on a steel bracket that I bolted onto a 200-gal. air tank. I also mounted a used compressor equipped with its own pulley on the bracket. I use a tractor to pto-drive the gearbox which belt-drives the compressor. The compressor blows air through a copper tube that goes through the bracket and into the tank. The original pulley on the gearbox was designed for a flat belt. I replaced it with a bigger 2-groove pulley, using an adapter to install it.

“I work part time for a construction business and got the idea while working at a place that had no electricity. I was given the compressor and found the tank alongside a road. I made an adjuster that lets me move the bracket back and forth to tighten the belt.

From the archive · Full text
Reader shop tip 2 of 2

Jack Dyck

Individual tip 2 of 2 from this reader’s published contribution.
Jack Dyck, Richmond, B.C.

“I also made my own pressure washer that’s powered by the engine off a 1962 Volkswagen Beetle car. I removed the clutch plate from the flywheel and filled in the center of the clutch with a small steel plate, then drilled holes into the plate and bolted on a 3-groove pulley. The pulley, covered for safety, belt-drives a Giant pump that I bolted onto a steel bracket. I bolted half of a VW transmission case to the engine block (the early VW transmissions were built in two pieces) and bolted an 8-in. channel iron bracket onto the transmission in order to mount the pump. Water travels from the pump through steel hydraulic hoses and into a wand (not shown). I knocked the valves out of the connectors on the hoses so that they’re totally open.

“The original VW fan housing is still used to cool the engine. I didn’t change anything on the housing except to close some ducts in order to get more air to the engine. I mounted a pair of switches on the housing. One is the ignition switch (the transmission contains the engine’s starter mounting) and the other activates an automatic throttle that I made. The throttle is a flow switch that’s activated by flowing water - it closes a relay which ener-gizes an electromagnet on the throttle. It always keeps the engine running at idle until I pull a trigger on the wand - then it will rev up the engine to its pre-set maximum. As soon as I let go of the throttle switch the engine returns to idle.

“The pump bracket has slotted holes for adjusting belt tension. I just loosen a bolt to adjust the tension.

“The fuel tank is from an outboard motor. I use an automotive electric fuel pump to supply the carburetor with fuel. The pump is wired into the ignition switch so that whenever the ignition is on, the pump is working.

“I’m semi-retired but have started a pressure washing business. I use my homemade pressure washer to clean houses, driveways, sidewalks, etc. I even use it to wash restau-rants. It mounts in the back of my pickup.”

From the archive · Full text
Reader shop tip

Jeremy Subriar

Jeremy Subriar, Riverside, Calif.

“K&N Engineering’s reusable ‘Million Mile Air Filter’ is the best air filter you can buy. It uses premium cotton gauze instead of conventional paper to increase the life of the filter, increase horsepower and mileage. Under normal conditions, you take it out and clean it every 30,000 to 40,000 miles using our cleaning kit, which includes a special cleanser. Then you simply rinse off the filter with water, let it dry thoroughly, lightly coat it with a mineral-based red-dyed oil (so you can see when it’s dirty again) and reinstall it.

“The filters, which come pre-oiled, are available for virtually any car or light truck, foreign or domestic, and we can often match sizes to fit farm equipment, too. Prices range from approximately $12 up to $120. Our cleaning kit sells for around $10.”

Contact: FARM SHOW Followup, K&N Engineering, P.O. Box 1329, Riverside, Calif. 92502 (ph 800 992-3000, access code 38-04, or 909 684-9762).

Shop feature stories

From the archive · Full text
Feature story

Heavy Duty, Adjustable, Two-Story Shelving

Featured source:

You can take advantage of all the available space in your shop with this 2 or 3-story storage system that eliminates the need to build structural floors. It uses heavy rivet-style shelving that you assemble with a hammer.

“These shelves are very versatile as you simply buy beams and posts. Beams come in lengths starting at 12 in. and go up to 48 in. in 6-in. increments, and 48 to 96 in. in 12-in. increments. Makes it possible to build a variety of shelf sizes from 12 by 12 in. up to 48 by 96 in. and build them 2 to 28 ft. tall with shelf levels adjustable on 1 1/2-in. centers. There are bolt-on walkways available for these 2 and 3-story systems, which makes it much safer to access the high shelves because you don’t have to work from a ladder.

“The shelves provide a lot of storage space while taking up little area because they take up dead air space that would normally be lost above 7 or 8 ft. high shelves,” says John Ward, St. Anthony, Iowa.

Standard units hold 350 lbs. per shelf; heavy units can hold up to 2,000 lbs. per shelf on 4-ft. wide spans.

The shelving system comes with a baked-on enamel finish. Galvanized or zinc plated finish is also available.

A standard shelving system that’s that’s 4 ft. long, 2 ft. deep, and 7 ft. high with 5 shelves sells for about $87 (plywood or wire decking not supplied).

Contact: FARM SHOW Followup, Ward Enterprises, 1223 170th St., St. Anthony, Iowa 50239 (ph 800 947-7929 or 515 477-8334; fax 8326).