Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 31, No. 2 (2007)

Vol. 31, No. 2 (2007)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

32 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

John Veneziano

John Veneziano, Olmsted, Ohio

“I installed a 12-volt GM HEI (high energy ignition) electronic ignition in my 1951 Ford 8N tractor. It works great and eliminates the points. Kits are available for just about any type of equipment and distributors. You get better starts and easier maintenance. Just search up ‘high energy ignition’ kits on the internet and you’ll find them.”

From the archive · Full text
Reader shop tip

Doug McAlexander

Doug McAlexander, Cedar Grove, Tenn.

“Here’s a tip if you need a long lasting gasket. I had a problem with a gasket on an older IH tractor with an ether start booster. The gasket was bad and replacements kept going bad, too. So I cut one out of an All-Flex cattle ear tag. It worked great. They’re tough, pliable and made to stand up to lots of abuse. Later, I needed a washer on a bathtub faucet and I used an ear tag for that, too. Worked great.”

From the archive · Full text
Reader shop tip

John Knowles

John Knowles, Seaford, Dela.

“An Indiana FARM SHOW reader recently wrote in about his spark plug problems on an 8N Ford tractor. I wanted to point out that the original spec Champion H-10 plugs will not perform satisfactorily with unleaded gas. He should switch to the H-12. That’ll get the job done.”

From the archive · Full text
Reader shop tip

Joe Rupnicki

Joe Rupnicki, Soldier, Kan.

“I got tired of dragging a welder and tools around the farm when equipment broke down. So I bought a large cargo van – I think it had been a bread delivery truck. It’s 6 1/2 ft. tall inside and about 20 ft. long. There’s plenty of room inside for my welder, cutting torch, air compressor, and all the other tools I need. I don’t have to worry about rain and I can look it up so no worries about theft. It has two doors at the back that open up as wide as the van. It’s great when working on rented fields 15 miles away. It’s one of the best buys I ever made.”

From the archive · Full text
Reader shop tip

Burton Graves

Burton Graves, Sandusky, Mich.

“I’m concerned about a story in your Vol. 30, No. 6 issue that showed a fellow squirting ether into a hole in the air intake on a tractor. I was a mechanic for many years and I’ve seen the damage ether can do to an engine. If you use too much, it can blow the bearings right off the crankshaft – that’s how explosive it can be. The thing is, you should never have to use either if you keep your tractor tuned, keep the air cleaner clean, and keep up on other maintenance. Unless your tractor is set up from the factory with an ether-starting system, using ether is a very dangerous habit to get into.”

From the archive · Full text
Reader shop tip

David P. Campbell

David P. Campbell, Elnora, Ind.

“The plastic bar cover I use on my chainsaw kept coming off because it didn’t fit tight enough. To solve the problem, I taped one end of a bunge cord to the cover and hooked the other end onto the saw. Now the cover always stays on tight. It won’t flop off as I’m driving down the road with the chainsaw in the back of my pickup.”

From the archive · Full text
Reader shop tip

Lowell Tuplin

Lowell Tuplin, Ellerslie, P.E.I.

“During winter I use a winch on back of my tractor to skid logs out of the woods, and small trees and branches were catching on the valve stems on the rear tires and breaking them off.

All the fluid would drain out.

“To solve the problem, I came up with a bolt-on valve stem protector for the tires. It consists of a 4-in. long steel strap that goes around the valve stem and has holes drilled into it to match the wheel nuts. The strap extends from the wheel nuts down to the valve stem. A small box is welded onto the strap iron.

“Commercial valve stem protectors are available, but they have to be welded onto the wheel rim. Besides, I can’t use them because my tires have tubes inside them, and the heat from welding could melt the tube.”

From the archive · Full text
Reader shop tip 1 of 2

Wess Cornelius

Individual tip 1 of 2 from this reader’s published contribution.
Wess Cornelius, Winlock, Wash.

“I wanted to use my cherry picker to lift engines but couldn’t get it close enough to my motorcycle lift with the legs on. To solve the problem, I built an extension rack on the rear and bottom of the cherry picker. A cable runs from the top of the mast to the rear bottom of the rack. The longer the rack, the more canti-lever ability I gain. I fill the rack with 5-gal. buckets of sand, scrap metal, concrete, etc.

From the archive · Full text
Reader shop tip 2 of 2

Wess Cornelius

Individual tip 2 of 2 from this reader’s published contribution.
Wess Cornelius, Winlock, Wash.

“There’s never enough level space in a shop. To solve this problem, I mounted metal doors with hinged legs to one of the walls. When folded up, the doors are out of the way. When folded down, the doors make a nice workbench.”

From the archive · Full text
Reader shop tip

Metal Supermarkets

Metal Supermarkets, 170 Wilkinson Rd., Unit 18, Brampton, Ontario, Canada L6T 4Z5 ph 866 867-9344 or 905 459-0466; www.metalsupermarkets.com

If you need metal bars, plate, or sheet metal, you’ll be interested in this company. It claims to be the world’s largest supplier of small quantity metal and says it can provide one stop shopping for all your small metal requirements. It has a network of more than 80 stores world-wide.

The company serves metal shops, fabricators, machine shops, hobbyists, artists, company maintenance departments, or anyone else who needs various pieces of metal. Unlike traditional shops, they’re able to fill small orders. They cut metal to the customer’s specifications and don’t require minimum order sizes. If customers want they can have the metal cut to size while they wait.

The company website lists metal guide quick links for a wide range of metals, including cold finished steel, hot rolled steel bars, alloy bars, structural steel, steel tube and pipe, sheet steel, steel plate, aluminum, stainless steel, brass and copper, specialty products. You can use the website to request a quote and to find the store nearest to you.

From the archive · Full text
Reader shop tip

Lee Horstmeier

Lee Horstmeier, Pecatonica, Ill.

“I put a motion detector light up on the opposite wall from the walk-in door in my shop. When it gets dark enough the light comes on when I exit. And I don’t have to remember to turn it off later.”

From the archive · Full text
Reader shop tip 1 of 2

Ray Tuchscherer

Individual tip 1 of 2 from this reader’s published contribution.
Ray Tuchscherer, Langley, B.C.

“My cow barn was quite a low building. It needed a new tin roof so last winter I removed the roof in sections, leaving half the wall studs attached, then placed taller studs beside the old ones to make the barn 6 ft. higher. Now I can drive any equipment into it.

From the archive · Full text
Reader shop tip 2 of 2

Ray Tuchscherer

Individual tip 2 of 2 from this reader’s published contribution.
Ray Tuchscherer, Langley, B.C.

“I installed an old-style garage hoist (in-ground, big cylinder) in my shop. Works great for servicing vehicles, and it also makes a great adjustable height work bench.”

From the archive · Full text
Reader shop tip

Allan Melanson

Allan Melanson, LaGrange, Maine

“I couldn’t find a distributor for my 1980 Massey Ferguson 230 tractor. But I was able to buy an electronic ignition module that’s designed to bypass the points and eliminate the need for them. After installing the module my tractor has never run better. We bought the electronic ignitor kit module from Gary’s Garage (Poland Spring, Maine ph 207 998-5100). It’s made by Pertronix Performance Products; www.pertronix.com. I think I paid about $20 for the unit.”

From the archive · Full text
Reader shop tip

Bill Kobiskie

Bill Kobiskie, Milton, Kansas

“One day while I was in the field the power steering cylinder on my 1960’s Case 930 tractor fell out. Apparently the threads on the cylinder stripped, causing the cylinder rod to drop out. It was a good thing it happened in the field because when this problem happens the tractor’s steering wheels go wherever they want to go. I tried to find a new replacement cylinder and drag link but couldn’t. I was going to have the cylinder rethreaded, but then it would be too small.

“I solved the problem by drilling a 5/16-in. dia. hole through the drag link and also through the cylinder rod, and then I put a bolt through the hole and added lock nuts on it. Works great. I used a regular 5/16-in. hardware bolt so it can shear. Two years later it hasn’t sheared or been replaced.”

From the archive · Full text
Reader shop tip

Bob Bugger

Bob Bugger, Effingham, Ill.

Bob likes to keep a tidy shop. That’s why he created this setup to capture and hold grit and sparks from his chop saw.

It’s an elbow and a small length of 3-in. dia. pipe that’s bent at an angle and leads from the chop saw’s original spark deflector down into a coffee can.

“The chop saw’s original spark deflector is designed to deflect grit and sparks forward instead of straight up. My pipe deflector improves on the idea by capturing most of the material in the coffee can,” says Bugger.

He built a base for the chop saw using an old brake drum and a stand pipe, on top of which he welded a metal table top. The chop saw’s original mounting plate attaches to this plate by a pair of screws.

“If I want to take the saw somewhere else, I just undo the wing nuts on the two screws and carry the saw off,” says Bugger.

The add-on plate extends about 18 in. off to one side of the saw, where cutoff pieces can drop onto it. A short length of pipe that’s welded under the plate serves as a depth guide for cutting multiple pieces to the same length.

“I just bump the piece I want to cut up against the pipe and saw it, then repeat the process.”

From the archive · Full text
Reader shop tip

Elmridge Machine

Elmridge Machine, 94 Fairview Rd., Lititz, Penn. 17543 ph 717 664-1079

A farmer came up with this 2-wheel dolly and it worked so well a local machine shop decided to put it on the market.

A hinged pin is designed to slide up into hitches on equipment tongues. As the long handle on the dolly is pushed down, the pin lifts the tongue up off its jack. Small and large equipment can be maneuvered into out-of-the-way corners for storage.

Sells for $155 plus storage.

From the archive · Full text
Reader shop tip

Mel Primrose

Mel Primrose, Westlock, Alberta

He built a 5 by 7-ft. portable work bench that he can move around the shop, sometimes right outside onto the building’s concrete apron.

He made a light channel iron frame and added three large wooden storage drawers on each side. The table’s legs each have 3-in. castor wheels, and he installed a vice, various hooks and a power outlet to make it more useful.

“I even surprised myself how much I use this table and how often I roll it outside. When the weather’s nice, I like to move it out onto the pad in front of the shop in the daylight. If I’m not finished at the end of the day, I can just roll it back inside for the night.”

To compliment the portable table, Primrose also built a portable stool and tool caddy that can go along with the table. In addition, he made a variety of tool carriers that can sit on the table but make it easy to transport various accessories from one place to another.

From the archive · Full text
Reader shop tip

Dale McIntyre

Dale McIntyre, Orangeville, Ill.

A couple dozen carriage bolts and an old bald car tire, helped Dale McIntyre extend the life of a tractor tire for another year.

The Orangeville, Illinois, man explains that one of the tires on his F-20 Farmall was old and had a small tear in it, where the tread met the sidewall. He only used the tractor weekly for moving snow and yard work, so he couldn’t justify purchasing a new tire.

When the tear got up to 1 ft. long, he decided to get creative. With his knife he cut out an 18 by 12-in. piece from an old car tire, which included the tread and a couple of inches of each sidewall. He sanded the edges to bevel them out so they wouldn’t damage the tractor tire’s tube. He slipped the piece of tire inside the tractor tire and drilled 3/8-in. holes every couple of inches, about 3 in. from the edge of the patching material. He slipped 1 1/2-in. long, 5/16-in. carriage head bolts through the holes from inside the tire and tightened washers and nuts on the outside.

“It looked a little strange,” McIntyre says, but it worked.

After a year he found a good deal on used tractor tires and took the patched tire off. The tube and tire were still working just fine, McIntyre says.

From the archive · Full text
Reader shop tip

Keith Switzer

Keith Switzer, Cromwell, Minn.

“I keep several sets of cheap tools around for difficult repair problems. That way, if I have to bend a tool or cut one off, I haven’t ruined an expensive tool. It’s surprising how often I use them.”

From the archive · Full text
Reader shop tip

Art Gomez

Art Gomez, Scott City, Kansas

“To change out a fuel pump on a 1986 GMC 305 V8, I cut out a piece of pliable plastic wide enough to fit in the engine block slot to hold the pin in place. I tried grease first to hold the pin but it didn’t work. After fitting the plastic into the slot, I could push the pin back far enough to slip the thin plastic behind it. The fuel pump arm fits right behind the plastic allowing me to get the pump in place.”

Shop feature stories

From the archive · Full text
Feature story

He’s Got Johnny Popper Parts

Featured source: Joel Martin

Need a gasket for a 1937 B John Deere? How about a radiator core or grill screen for a 1947 MC built at Deere’s Dubuque factory? Maybe you need original style lights for a 1957 620 or a muffler or sway block kit for a 1967 3020? Whether it’s a part for a 2-cylinder Johnny Popper or a New Generation 4-cylinder, Joel Martin has it. If he doesn’t have it, he knows where to get it.

“Most of my work is with two-cylinders, but I have parts or can get them for newer Deeres too,” says Martin.

“I can get parts for just about any other brand.”

It is Deere tractor parts, however, that his Martin Parts & Repair specializes in finding. Demand for his services and his parts continues to grow as Deere phases out and stops making parts for its older tractors. It is also a market that Martin grew into.

“I grew up farming with older tractors and working on them,” he says.

“I bought one and fixed it up and sold it. Then I started doing it for others, and finally I got into selling parts. For the past 6 years, it has been a full time job.”

Martin still restores 2-cylinder Deeres, though mostly for other people. He also breaks some down for parts he and others need. While he also sells Deere parts if available, it is the after market or reproduction parts that are the biggest sellers.

“We sell a fair amount of piston kits,” he says.

“After 40 to 50 years or more, engines wear out. With aluminum pistons, the tractors have higher compression and more power. Gasket kits from Deere are pretty expensive, so I stock whatever I can get from aftermarket suppliers.”

Contact: FARM SHOW Followup, Martin Parts & Repair, 217 S. Red School Road, Morgantown, Penn. 19543 (ph 610 913-6299; [email protected]).

From the archive · Full text
Feature story

Home-Built Radial Arm Saw For Cutting Steel

Featured source: Loron Skretteberg

“I used to build pole buildings and hated using tin cutters to cut the sheet metal. So one weekend I went out to my shop and built a radial arm steel cutting saw,” says Loron Skretteberg, Carson, N. Dak.

The saw will cut sheet steel at any angle up to 45 degrees.

“Once you get your angle set, one person can cut faster than four people can put up the sheets. It reduces the time it takes to put up the sheet metal on a building by at least 50 percent,” he says.

The sheet metal panel lays between a set of angle iron guides to keep it straight. The panel guide frame is 36 in. wide which is the standard sheet metal width.

The saw is set up on a 2-wheeled, home-built trailer and is powered by an electric motor that has a 16-in. blade bolted to it. The motor is bolted to a small metal carriage that’s free to ride between a pair of channel iron guides. To change the cutting angle the operator simply loosens a set screw.

To attach the cutting blade to the motor, Skretteberg had a local shop machine a big 1-in. dia. bolt and drill a hole in the bolt head so the bolt could be slid onto the motor’s shaft. The blade has a 1-in. dia. hole in it which fit right over the other end of the bolt. A nut keeps the blade on tight.

“As far as I know, no one makes a commercial radial arm cutting saw that can handle pole barn sheet metal, which comes in 3-ft. wide strips. My only expense was for the blade,” says Skretteberg.

“Whenever I start moving the blade across at an angle the sheet metal tends to vibrate and pull the sheet back. To keep the metal from sliding I clamp a vise grip onto a small metal tab on back of the trailer.”

Contact: FARM SHOW Followup, Loron Skretteberg, 5880 54th Ave. S.W., Carson, N. Dak. 58529 (ph 701 622-3261; [email protected]).

From the archive · Full text
Feature story

Snowmobile Engine Converted Into Low-Cost Air Compressor

Featured source: Wess Cornelius

Wess Cornelius couldn’t justify the expense of a new air compressor. So the Winlock, Wash., man converted a Rotec 500 cc, 2-cyl. snowmobile engine into a low-cost air compressor.

A 3/4 hp electric motor shaft-drives the Rotec engine, which is used to deliver air to a nearby air tank.

He removed the two spark plugs from the top side of the engine, then used square steel tubing and nylon block to build a pair of shuttle valves which he welded into the spark plug holes. He closed off the engine’s intake ports and hooked up a pair of 1 1/2-in. dia. rubber hoses to the exhaust ports. The hoses are hooked up to a commercial air tank. Turning on the electric motor, via a pressure switch, causes air to get sucked in through the shuttle valves. At that point the engine’s pistons go down, the valves open up, and the air is moved through the spark plugs toward the piston. As the pistons come back up, the valves close off and air is pushed back out the hoses and exhaust ports.

A check valve at the air tank keeps air from coming back out of tank and into the engine.

“I use it to do heavy duty work in my shop,” says Wess.

“It didn’t cost much to build. I already had the electric motor and the air tank. I bought the Rotec snowmobile engine for $10 from someone who didn’t need it any more.”

Contact: FARM SHOW Followup, Wess Cornelius, 1312 Ferrier Rd., Winlock, Wash. 98596 (ph 360 785-4178).

From the archive · Full text
Feature story

“Carousel Shop Table”

Featured source: Wess Cornelius

“It puts my shop tools right at my fingertips without having to do any walking,” says Wess Cornelius, Winlock, Wash., who converted a round wooden kitchen table into a rotating shop table.

He started with a 4-ft. dia. wooden table with a single leg leading down to a metal base. He cut the pipe off, then slipped an-other pipe of smaller diameter inside the cut-off pipe, Then he welded the smaller diameter pipe to the base of the table.

He can raise the table to the elevation he wants by adjusting a collar that he mounted on the bottom pipe.

“It’s amazing how well it works,” says Wess.

“Sometimes I line up tools and parts around the entire perimeter of the table. That way I can stand in one place and work on multiple facets of a project. I lay something out, and as I need a tool or part I can grab hold of the table and bring the tool to me. I bolted a vise to the table because a vise comes in handy for many different projects. ” Contact: FARM SHOW Followup, Wess Cornelius, 1312 Ferrier Rd., Winlock, Wash. 98596 (ph 360 785-4178).

From the archive · Full text
Feature story

Repowered Skid Steer Runs “Better Than New”

Featured source: James Ruopp

A broken timing gear in the motor of his Case IH skid steer turned out to be good luck for James Ruopp. With no parts to be found, he had no choice but to replace the old Tecumseh motor.

“I had a lot of trouble with the Tecumseh and had been considering replacing it for several years,” says Ruopp.

“I chose a Briggs and Stratton Vanguard. It can do at an idle what the other engine struggled to do at full power, and it’s only two horsepower bigger.”

The V-Twin Vanguard engine he went with produces 18 hp to the Tecumseh’s 16. Re-placing one with the other was fairly simple. In addition to pulling the engine out, Ruopp also eliminated the electric fuel pump and the rectifier that charged the Tecumseh battery, neither of which were needed for the integrated Vanguard.

The Vanguard still needed more space to fit the Case skid steer compartment. Ruopp removed the backup rope pull starter to create clearance for the oil cooler at the rear of the engine. Needing still more space, he cut about 1/2 in. off the engine mount. This allowed him to line the engine up with the electric clutch that runs the hydraulics. Bolt holes to secure the engine matched perfectly.

“I thought the biggest problem would be matching the Vanguard’s 1-in. crankshaft with the electric clutch that was built for the Tecumseh’s 1 1/8-in. crankshaft,” says Ruopp.

“A machinist in town solved the problem easily with some shims.”

Ruopp also rerouted the throttle cable and plans to reroute the starter switch currently on the engine.

“It has not been a problem yet, as I can reach back and start it or adjust the choke,” he says.

“The Vanguard works great,” says Ruopp.

“My only regret is not doing it sooner.”

Contact: FARM SHOW Followup, James Ruopp, 2730 160th St., Marshalltown, Iowa 50158 (ph 641 753-7048).

From the archive · Full text
Feature story

Car Motor Makes Good Sandblaster

Featured source: Harold Witulski

“I made a sand blaster-compressor from a car motor,” says Harold Witulski of Beatrice, Neb.

“The sand tank is made from an old water softener tank.”

Since he already had the old motor and hydraulic hoses, the only thing he had to buy was the ceramic nozzle and a sandblasting hood to protect his head.

Witulski started his project by removing the valve rocker arms, intake springs and push rods from the motor. Then he installed lightweight springs on the intake valves so when the piston goes down, it can suck air in.

“I removed the carburetor and made an adapter for the air cleaner. Next, I removed the inside of the eight old spark plugs, and welded on the outer ring of a one-way hydraulic ball valve (which lets the air out of the cylinder one way and won’t let it back in),” he explains.

“These were taken off of hydraulic fittings.”

Witulski ran hoses from the valves to an air manifold he’d made from a foot-long section of 2-in. pipe with plugs welded on both ends of it. Then, he drilled holes along the pipe’s length, positioning four on each side to go to the spark plugs, and a large hole on one end to go to a T at the bottom of the sand tank. After welding fittings into the holes, he used a 1-in. hose to connect the end of the pipe to the sand tank, and 1/2-in. hoses, which run to the spark plugs, creating eight places for the air to go in.

At the other end of the pipe, he installed a smaller hole and fitting for a 3/8-in hose which allows the air to exit to the top of the sand tank.

He made the sand tank by placing a ball valve at the bottom of an old water softener. Witulski connected this to a T where the air comes in. The T also has a 1-in. dia. hose connected where the air and sand travel out to the ceramic sandblasting nozzle.

“When you open the ball valve, the sand will fall down into the air stream,” he explains.

“There was already a 3-in. hole at the top of the tank, with an airtight plug that works good to put the sand in. You adjust the ball valve at the bottom to set the amount of sand you want in the air stream.”

Witulski mounted a salvaged pto to the engine, allowing him to hook onto the tractor’s pto. This turns the compressor engine the same way it did while running on the car. In this way, he says he’s able to maintain oil pressure in his motor.

“I also moved the car’s radiator and fan to the back end of the motor for cooling.” he says.

“You have to use dry sand, otherwise it will plug up everything. I usually get fine fill sand ahead of time and shake it through a house screen to make sure it’s fine enough - then let it dry in the shed so it’s ready to use.”

Witulski says he generally uses his sand blaster for only an hour at a time, but cau-tions that if you’re going to use it continuously, you should probably use copper tubing from the spark plugs to the manifold because it gets pretty hot.

Contact: FARM SHOW Followup, Harold Witulski, 8558 W. Lilac Rd., Beatrice, Neb. 68310 (ph 402 228-0633).

From the archive · Full text
Feature story

Semi Shop Trailer

By By Rex Gogerty
Featured source: Christiansen Brothers Construction

I spotted this converted semi trailer used by a local construction company. I think the idea could also be useful for farmers who are short on shop space, or who want a mobile work space.

Christiansen Brothers Construction in Cherokee, Iowa, used lengths of strap iron and expanded metal to make steps, railing, and an unloading platform on back. The easy-to-setup folding platform has enough room to swing out the big doors on back, and to carry large work in and out of the trailer. There’s also a door cut into the side of the trailer, and storage racks and large drawers hanging under the bed of the trailer.

From the archive · Full text
Feature story

Farmall H Repowered With Mercedes Benz Diesel

Featured source: Lloyd Statz

Put a Mercedes Benz 2.2-liter, 4-cyl. diesel engine into a 1944 Farmall H and you’ll have a nice, smooth-running combination, says Lloyd Statz of Elmwood, Wis., who did just that.

“Years ago I used a tractor just like this one to do chores. I always thought it would be great to repower a Farmall H with a Chevy 6-cylinder engine. However, the Mercedes engine looks like it belongs in there. I spent about six months on the project.”

The engine came out of a 1969 Mercedes Benz that had been setting in the weeds for about 10 years. Statz is a bison rancher, so he was able to trade bison meat for the car. He bought the tractor from a neighbor for $200. The engine on it was frozen.

The tractor still has its original starter, flywheel, and bell housing. The new engine was the same length as the original one so he didn’t have to lengthen the tractor frame at all. The crankshaft on the Mercedes engine was slightly shorter than the one on the tractor’s original engine, so he had an adapter made to fit between the crankshaft and the tractor’s original flywheel.Installing the fan was tricky. There wasn’t room for the tractor’s original fan, so he found one off another car. A pulley off another IH tractor is used to belt-drive the fan.

He welded a short length of channel iron vertically to the left side of the tractor to support the alternator. He also cut a notch in the tractor’s frame rail to provide room for the oil filter. He also bolted on new motor mounts.

He used 4-in. dia. steel pipe to make a muffler and mounted a commercial exhaust pipe inside it.

“It runs smooth without being too loud,” says Statz.

“Running at idle it makes a little bit of a diesel hammering sound, but when I run it a little faster, say at 1,500 rpm’s, it sounds more like a gas engine. Generally I run the engine at 2,000 to 2,500 rpm’s.

“It runs super cheap for doing light chores.

I used it last fall to operate an auger and deliver corn into a 3,000 bu. bin, and the fuel level hardly went down at all. I removed the tractor’s original hydraulic system and installed a belt-driven hydraulic pump so it now has live hydraulics. I used the hydraulics last summer to operate an 8-wheeled hay rake.

“At tractor speed, it doesn’t have much more power than the H but it will run faster. I’ve had it up to 35 mph, and I think in high gear it would go 40 mph.

“The hardest part of the project was installing the fan, and rerouting the radiator hose to the opposite side of the engine.”

Despite setting outside for 10 years, the car engine started right up.

“The first thing I did was to put a big channel lock on the front pulley and turn it. I was surprised that I could turn the crankshaft over. It didn’t turn hard at all,” notes Statz.

Contact: FARM SHOW Followup, Lloyd Statz, N6148 170th St., Elmwood, Wis. 54740 (ph 715 639-3205; [email protected]).

From the archive · Full text
Feature story

He Custom-Machines Complex Parts

Featured source: Levi Glick

Getting rough work milled or machined is seldom hard to do at a local metal shop. But getting a complex part machined, which requires fine valve and stem work, can be a lot tougher. One alternative is to use a remote machinist that specializes in exacting work. Levi Glick of H.C. Co., Quarryville, Penn., is one such specialist.

“A mechanical drawing or sketch is ideal for us to work from, or we can reproduce from a sample piece or a damaged part,” says Glick.

“We can even take dimensions over the phone or by fax.”

Glick has an automatic milling machine that works with bar stock up to 1 1/2 in. in diameter and up to 6 in. long, producing very complex pieces. He is also equipped to do milling and lathe work on larger pieces of stock.

Past work has included tapered shafts and tubes up to three feet in length, as well as hub machining and one-of-a-kind carburetor parts. Custom business is a small part of his workload, with the majority of his business associated with propane lamp burners.

“Lamp line heads with their valves, valve wheels and stems are very exacting and are about 90 percent of our business,” he says.

“We’re always interested in production work, but are also available for custom work.”

Contact: FARM SHOW Followup, H.C. Co., 418 Furnace Road, Quarryville, Penn. 17566 (ph 717 786-1049; fax 717 806-3093).

From the archive · Full text
Feature story

Kit Solves Cold Weather Problems With Honda V-Twin Engines

Featured source: Ken Young

“Our new air induction kit solves cold weather icing problems on Honda V-twin engines equipped with overhead muffler systems,” says Ken Young, Brandon, Manitoba.

The kit is designed only for V-twin 20 and 24 hp Honda engines equipped with overhead mufflers.

“These engines are commonly used on grain augers and belt conveyors. They’re good engines, but they have a problem with the carburetor icing up in cold, damp weather and stalling the engine,” says Young.

“It’s hard to tell whether the carburetor is flooding or starving for fuel. This problem happens because it takes a large fan to keep the two cylinders cool, and the large blast of cold air coming off the fan supercools the carburetor, causing it to ice up.”

The kit consists of a metal deflector that prewarms the air going into the carburetor. The deflector bolts onto the back side of the engine, forcing the carburetor to draw warm air from the muffler before it enters the carburetor.

“The kit can stay in place all year long. You can switch from warm weather to cold weather operation instantly by simply flipping a lever, which redirects the air flow away from the muffler and into the engine’s normal air intake system,” says Young.

“It takes less than 20 minutes to install the kit. A small notch has to be made in the air filter cover to accommodate the air deflector that goes on the side of the engine.”

Sells for $125 (Canadian) plus S&H. Contact: FARM SHOW Followup, Ken Young, Site 325, P.O. Box 17, RR 3, Brandon, Manitoba, Canada R7A 5Y3 (ph 204 728-2714; [email protected]).