From the archive · Full text
Feature story
Featured source: Ted Lacey
The floor chain on Ted Lacey’s 30-ft., self-loading round bale trailer was loose, and he was worried that it might jump off the frame. He had already taken out all the slack he could by using the trailer’s…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Red Rock Mfg., Pella, Iowa; ph 641 780-1748; www.redrockmfg.com
Their cast iron drawbar lock is a one-piece device that stops the 3-pt. drawbar from turning on Ford 9N, 8N, and 2N tractors, as well as some smaller Ferguson tractors. No bolts or pins are required for installation.
Read the complete tip →From the archive · Full text
Reader shop tip
SpynTec Industries, LLC, North Lima, Ohio ph 234 759-3105; www.spyntec. com
Their fuel-saving, free-spinning hub conversion kits are designed to solve problems associated with the wheel bearings on many Ford, Dodge, and Jeep vehicles.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Mike Becker
Mike Becker has no problem parting with his collection of manuals, brochures and ag equipment memorabilia. He says it helps that he is a “paper farmer”, not a collector.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S. Dak.
“I carry a generator in the back of my 2004 V-10 Ford pickup and needed a heat shield to protect the paint on the side of the box from muffler heat. I bought a metal basement window protector…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S. Dak.
“I’ve been carrying the generator around for years because it seems like there’s always a low tire or dead battery that needs fixing when you’re too far away from an electrical outlet. I recently had to replace the…
Read the complete tip →From the archive · Full text
Reader shop tip
Joe Bellor, Lapeer, Mich.
“To minimize problems with tires on wagons and trailers, we use silicone grease to seal the bead against leaks. We only use tubeless tires because they’re easier to put on and off.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: S&B Filters
Anyone who drives a pickup truck in extremely dusty conditions will be interested in the Truck Particle Separator filters from S&B. These are military-grade products with 49 small vortex tubes that clean dusty air before it enters the…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: PacPro Performance Parts
If you’re tired of dismantling half your Dodge pickup just to change the oil, you’ll like the new PacPro oil filtration relocation kit that moves the oil filter out into an open area for quick, hassle-free oil changes.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Tyler Daly
“Our new Tailgate Sawhorse extends your pickup or utility vehicle bed by 3 ft. using only a pair of ordinary 2 by 4 boards. Your vehicle then becomes a portable workbench,” says Tyler Daly, Erickson Mfg. Ltd., Thamesville,…
Read the complete story →From the archive · Full text
Reader shop tip
Quinton Parker, Fairbanks, Alaska
He’s a diesel mechanic at a shop that works with heavy diesel equipment such as loaders, bull dozers, and semi trucks.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Richard Liberda, Mandan, N. Dak.
“Mike also fixed my wife’s wheelchair. The wiring was shot so I took it to two places in town but they wanted a lot of money to rewire the chair. Mike just cut off the ends of wires…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Howard Ewen, Jr.
Overhead oil tanks, drip collectors and organized filters keep Howard Ewen’s shop clean and neat, making oil changes a lot easier. With 4 IH 4586 diesels, around 30 Olivers, 5 or 6 farm trucks, 3 pickups and several…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Vernon Hershberger
The older the baler, the more likely its owner will end up calling Vernon Hershberger for parts and repair, or at least advice. Fixing balers is a big part of Hershberger’s farm equipment repair business. If a customer…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Paul Petrocchi
Paul Petrocchi at American Windmill restores gear cases to better than new with a special oil seal and roller bearings.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Scott Urschel
Scott Urschel is a bonafide expert in the repair, restoration and general maintenance of Cub Cadet lawn and garden tractors. Urschel’s Cub Cadet Connection business carries a large supply of new, used and reproduction parts for virtually every…
Read the complete story →From the archive · Full text
Reader shop tip
Jeremy Simon, Blooming Prairie, Minn.
“I set up a battery charging station using an old Dewalt tool case. Using a rotary tool, I cut out the dividers in the case to make room for the chargers, which are held in place by a…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Dale McLaen
Old oil filters don’t last long in Dale McLaen’s on-farm auto repair shop. His shop-built, hydraulic crusher can handle even large truck and tractor filters and do it faster than $1,600 commercial alternatives.
Read the complete story →From the archive · Full text
Feature story
Featured source: Kenny McCulley
As an owner of businesses that use big trucks and heavy equipment, Kenny McCulley has accumulated an impressive collection of unique and expensive wrenches. But a couple of his “sideways” wrenches caught our attention.
Read the complete story →From the archive · Full text
Feature story
Featured source: Ron Heidebrink
Retired engineer and pilot Ron Heidebrink has invented a double alternator for use on farm tractors, combines and other vehicles such as trucks, construction equipment and even military vehicles.
Read the complete story →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Stephen Zonies, Fayston, Vt.
“I had a rusty bumper that wouldn’t pass Vermont’s vehicle inspection. Instead of buying an expensive replacement bumper, I filled it in with body putty and hardware cloth. The repair has lasted for years.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Andrew Sokol
“You can give your diesel pickup exhaust a more finished look with our new Sinister Dual Wall Exhaust Tip. It’s relatively inexpensive and easy to install,” says Andrew Sokol, vice president of sales and marketing at Sinister Diesel…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Jim Carter
If you have an old GM truck from 1934 to 1972 you’ll want to check out Jim Carter Truck Parts. The Independence, Mo., businessman has been restoring and dealing with antique vehicle restoration parts for more than 30…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Tom Buckley, Surprise, Az.
“A lot of people don’t know about Tri-Flow Superior Lubricant. It contains Teflon and is great for lubing locks, hinges, and much more. It’s great on my 1952 F3 pickup. No shop or work truck should be without…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Steve Cotsalas
If you have rusted equipment or tools, instead of trying to remove the rust, consider “converting” the rust - never to return again. That’s what Black Star Rust Converter does according to Steve Cotsalas, president of MROCHEM.com, which…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Andrew Sokol
You can keep your diesel engine coolant clean with a new filtration system from Sinister Diesel. It filters out casting sand, metal shavings, rust and mineral deposits that are even found in new engines. On high mileage and…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: LeRoy Oleson, Jr.
If you need a part for a riding mower, LeRoy Oleson, Jr., likely has it. He has mowers by the hundreds waiting to be parted out and mower parts on shelves numbered in the thousands. His South Dakota…
Read the complete story →From the archive · Full text
Feature story
Featured source: Michael Heron
When the hydraulic pump on his 1980’s Deere F425 hydrostatic drive riding mower failed and a new pump from Deere couldn’t be found, Michael Heron, Rivercourse, Alberta, decided to replace it with the power steering pump off a…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Gary Swensen, Yankton, S. Dak.
“When I use my gooseneck trailer, I like to put some grease on the ball. When it’s not in use the grease collects dirt and leaves. This little coffee cup solves the problem.”
Read the complete tip →From the archive · Full text
Reader shop tip
James Rissler, Hopkinsville, Ky.
“The brass pickup tube froze and cracked on an older Briggs & Stratton engine – the kind that has a metal gas tank with the carburetor on top. In the winter, water got into the gas and froze,…
Read the complete tip →From the archive · Full text
Reader shop tip
Andy Kozlowski, Califon, N.J.
“I don’t like shop workstands that make you hold the stand at the desired height and then try to lock it in place at the same time. The problem isn’t as bad when working with fixed height surfaces…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Christopher Hubbard
Engine tinkerer and car enthusiast Christopher Hubbard was often frustrated with the poor performance of conventional oil filters and the fact that they haven’t changed much in 50 years or more. So he took the giant leap of…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Andrew J. Horst, Hagerstown, Md.
“During cold winter months hydraulic hammer paste can’t be pumped. So I slide the grease gun into my truck tailpipe with the truck running to heat it up. Works great.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Andrew J. Horst, Hagerstown, Md.
“The tube for windshield washer fluid cracked on my truck. Rather than replacing the whole thing, I cut out the bad section and used electrical heat shrink tubing infused with glue to install a new section. Worked great…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S. Dak.
“One of my sons is the parts manager at a local Ford dealership. He let me come in one day to take pictures of the mechanics working on a truck engine. It’s a lot different working on a…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S. Dak.
“I bought a small tire machine from Harbor Freight. I don’t use it that often because it only works on small tires so I didn’t want to mount it in my shop. Instead, I mounted it on an…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron McMurray, Beverly Hills, Fla.
“In a recent issue of FARM SHOW a reader said he was having trouble keeping the headlights on in his Dodge pickup, even after he changed out the switch. I think he has a bad ground on the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Bob Muller, Delanson, N.Y.
“On older vehicles, I often replace the plug in the bottom of fuel tanks with a 2 to 3-in. nipple and petcock. This serves as a ‘dirt leg’, allows me to easily drain off old gas, check for…
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Payne, Coldwater, Miss.
“A couple of years ago I got a good deal on a heavy steel shop table, but I wasn’t sure where to place it in my shop. Putting the table against a wall would limit its use for…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Rickie Stich
Rickie Stich, Portersville, Penn., converted a shop engine hoist to mount on the back of his Kubota 23 hp. tractor, by fitting it with 3-pt. mounting brackets. He can quickly convert the hoist back to a stand-alone unit…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Jeff Grantmeyer
“Chrysler has been screwing up steering since the first Dodge Ram,” says Jeff Grantmeyer at Borgeson, manufacturer of replacement steering components.
Read the complete story →From the archive · Full text
Reader shop tip
Abe Snake, Peebles, Ohio
“If you are the owner of an AMC or Chrysler-produced vehicle equipped with a 4.0L fuel-injected 6-cyl. engine that hasn’t already had coolant leak into the crankcase, don’t be smug. There is ample evidence in the salvage yards…
Read the complete tip →From the archive · Full text
Reader shop tip
David Norman, Bay St. Louis, Miss.
“I keep hydraulic floor jacks in 4 different pickups. I gave each jack an extra 2 in. of lifting height by welding a 4-in. length of 2-in. square tubing onto it. I removed the pin that secures a…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Gary Swensen
“One day two of my sons each had projects going outside where they needed compressed air, sharing one large line from the compressor in my shop. When I asked if I could use the hose to air up…
Read the complete story →From the archive · Full text
Feature story
Featured source: Ben Wagner
Ben Wagner faced a $2,000 bill to fix a leak around the dipstick on his 7.3 Power Stroke Ford truck until a friend shared a tip. All he needed was a 20-gauge shotgun bore brush and a piece…
Read the complete story →From the archive · Full text
Feature story
Featured source: John Baker
“Thanks to the internet and PayPal, I was able to grow a tiny custom gasket-making business into one that supplies customers in the U.S., Canada, Britain, Australia and many other parts of the world,” says John Baker, owner…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Will and Ryan Garrett
Brothers Will and Ryan Garrett followed their father into the business of repairing radiators. Later, it was their desire for working “outside the box” that got them into custom manufacturing. Fifteen years later Radiator Supply House produces custom…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Brandon Parks, Geno’s Garage, Cumming, Ga. (www.genosgarage.com; ph 800-755-1715)
“The oil filter in 2013-2018 Ram Cummins heavy-duty pickups is notoriously difficult and messy to remove. Our oil filter cap-off tool threads onto the top of the filter, allowing you to easily pull the filter straight out without…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Jerry Lanser, Longmont, Colo.
“I have a 4 by 8-ft. freestanding workbench which works great, but there was never enough room to store commonly used tools close by.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Glen Wasmuth
Glen Wasmuth takes his tools to the job, whether in the shop or around the yard. His shop on wheels is loaded with tools of all sizes, from wrenches and bits to grinders, cutting torches, drill presses and…
Read the complete story →From the archive · Full text
Reader shop tip
D.S. Lindsay, Val Caron, Ontario
“I regularly fill old flat tires with expanding foam designed for insulating cracks in buildings. It works great on the right tires. You don’t use it on high-speed car or truck tires. But for tires used around the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Martin E. Matousek, Lake Geneva, Wis.
“After working on vehicle brake systems, I smear chassis grease on the brake bleeder screws and over the threads on steel brake lines and hoses. It seals them to keep out road salt and water. Next time you…
Read the complete tip →From the archive · Full text
Reader shop tip
Tony Ryba, Johnstown, Penn.
“I have a 2016 Ford F150 XL truck. Sometimes, when backing up, I’ll open the door and look behind me. The warning chime goes off and the warning lights come on telling me the transmission is not in…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Harrell Cummings
Last spring when Harrell Cummings bought a new hand truck, he didn’t throw out the old one. Instead he repurposed it into a useful welding cart.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Chris McClure
The MaxJax lifting system by Danmar is a portable, two-post lift that can fit in any garage. Roll it into place and bolt it to preplaced, drop-in anchors. Hook it up to the mobile power unit, attach the…
Read the complete story →From the archive · Full text
Feature story
Featured source: Don Prestien
Don Prestien, Wildwood, Mo., turned an old engine-driven 10k generator into a pto-driven unit that can operate off any tractor’s 540 rpm pto. He took the fan drive pulley and pto shaft off an old portable grain dryer…
Read the complete story →