From the archive · Full text
Feature story
Featured source:
An old AT & T service truck box makes a handy field service trailer for Nebraska farmer Charles Myers. He mounted the box onto a 3/4-ton pickup chassis and welded a homemade tongue on front.
Read the complete story →From the archive · Full text
Reader shop tip
Don Voss, Spiritwood, Sask.
“To re-pair combine pickup rollers, round baler rollers, Hesston straw chopper rotors, and any other rollers that have shafts with only one washer supporting the end, we’ve come up with a handy repair. We install two washers inside…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
The next time you need replacement drive train parts for your farm machinery, car, or truck, you might want to contact a Virginia parts supplier that sells drivetrain and component parts for 2 and 4-WD vehicles as well…
Read the complete story →From the archive · Full text
Reader shop tip
Keith P. Mayer, Naper, Neb.
“I own two GM pickups powered by 6.2-liter diesel engines. The engines work great and burn less fuel than comparable gas engines. The only thing I don’t like about them is the glow plug starting system.
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Stelmarski, Chesterland, Ohio
“We sell high quality rust replacement patch parts for domestic and foreign trucks, pickups and automobiles. We use only galvaneel, zinc over baked metal, to ensure that our parts will virtually never rust. As an example, we have…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
You can crush used oil filters to a fraction of their original size with this new “economy crusher”, says Bagley Equipment, Lodi, Calif.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Carol A. Brannaman, Mount Vernon, Iowa
Preventing tangles in extension cords has never been easier, thanks to this idea Carol came up with after she hauled away a pickup-full of old V-belts from a neighbor’s farm sale.
Read the complete tip →From the archive · Full text
Reader shop tip
Charlie Stough, Thermopolis, Wyo.
“There are many problems with the thermal linear actuator used to engage the 4-WD on late 1980’s GM pickups through current models. It’s an electro-mechanical part with an atrocious failure record. GM replaces over 100,000 a year. There…
Read the complete tip →From the archive · Full text
Reader shop tip
Ed Engdahl, Aurelia, Iowa
“I’ve discovered a way to remove hex nuts from axles on any 18-wheeler without using a hammer and chisel. Works great to take off wheels to repair axles or bearings.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.
“Here are a few shop-built tools I can’t do without.
Read the complete tip →From the archive · Full text
Reader shop tip
Jim & Roger Koppes, Medina, Ohio
“Here’s a time-saving revision we’ve made to strap ratchets on our flatbed bale-haul-ing trailers. By welding a 1/8-in. piece of flat stock onto the end of the ratchet and cutting a 3/8-in. square hole in the center, I…
Read the complete tip →From the archive · Full text
Reader shop tip
Richard Day, Neligh, Neb.
“You can start cold tractors and combines with what I call ‘jumper hoses’ that circulate hot coolant from a warmed-up engine to the cold one. You need two lengths of heater hose. Just cut the heater hose on…
Read the complete tip →From the archive · Full text
Reader shop tip
Charles Smart, Shellbrook, Sask.
Charles built a hydraulic shop press that attaches to a punch press so he could repair the housing on his 27 1/2-ft. 4153 Will Rich air seeder.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.
“Our 1987 Ford 250 diesel pickup is strong and runs good but the hydraulic clutch is poorly engineered. The master and slave cylinders are made out of plastic and wear out about every 50,000 miles. The cost to…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.
“To safely change the rear transmission on my 10-yard dump truck, I built a wood frame that goes just behind the cab, and I hung a chain and come-along from both the wood frame and from the hydraulic…
Read the complete tip →From the archive · Full text
Reader shop tip
Norman Foellmi, Sparta, Wis.
“I’ve discovered a new use for my wood splitter. I bent the forks on my bale loader and needed a way to straighten them out. I laid a railroad tie across the splitter, put the bent fork against…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Baldwin, Rock Rapids, Iowa
Back in the early 1960’s, before the advent of portable AC welders, Roger built a DC welder from a 32-volt generator out of a surplus WW II airplane.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Tom Graham, Henderson, Minn.
“I’ve discovered that auto salvage yards that wreck late model cars have used anti-freeze available. I bought a 55-gal. drum for $25 and use it in all my older cars, truck and farm machinery. Works as good as…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
If you’ve ever thought of turning an old engine into a high-volume air compressor, you’ll be interested in the way Clayton, Ill., farmer David Buss modified a 1961 Ford car engine to compress air. Buss left three of…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Lanny Hecker, Faucett, Mo.
“We put two pits in the floor of our shop to make it easier to service the bottom of vehicles. Much easier than jacking them up and using a creeper.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Lanny Hecker, Faucett, Mo.
“I came up with a handy device to check brake lights on cars and trucks when working alone. I welded a rod with a disk blade spacer on it for weight to a pair of vice grips. When…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
When you change the dirty oil in your tractor or combine’s engine, you probably think the job is done.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I built it to slip over the front bumper on my Dodge 3-ton grain truck to make it easier to service the engine,” says Michel Dufault, Haywood, Manitoba, about the 5-ft. long, 1-ft. wide service step he made…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 5
Individual tip 1 of 5 from this reader’s published contribution.
Edwin Ruff, Moses Lake, Wash.
“I mounted an automotive air conditioning compressor on the engine in my pickup, driven by V-belt off an extra pulley on the crankshaft. I mounted an air tank under the pickup between the frame to hold air and…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
James B. Barbour, Hallstead, Penn.
“Another idea I had was making a cradle to fit my hydraulic floor jack to make it easier to change starters on cars or trucks. It’s just a short piece of channel iron with a bolt down the…
Read the complete tip →From the archive · Full text
Reader shop tip
Peter DeJong, Sebringville, Ontario
DeJong cleans field drain tile as a sideline business.
Read the complete tip →From the archive · Full text
Reader shop tip
Scott T. Frank, Loveland, Colo.
“I put 2-in. wide strips of industrial velcro along the top rail on each side of the bed of my Ford F-150 pickup. Then I put some under my cross-mount toolbox which holds the toolbox in position anywhere…
Read the complete tip →From the archive · Full text
Reader shop tip
Ed Panchyshak, Windsor, Ontario
“If you need an owner’s manual for an older model car or truck, there’s a company in California that can help. Call Faxon Auto Literature at 1-800-458-2734 or write to: 1655 East Sixth St., Corona, Calif. 91719. The…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Branum, New Madrid, Mo.
“Another idea that works well for us is a seat I built that slides onto the tow hooks of my GMC 4-WD pickup. It rides low to the ground, extending out to the left side of the truck.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Molnar, Leonard, Mich.
“I use a paint pen to write the size of wrench needed for the oil plug and type of filter needed under the hood of all my vehicles. This allows me to have the right tool when I…
Read the complete tip →From the archive · Full text
Reader shop tip
Alice & Robert Tupper, Canton, S. Dak.
“We’ve discovered we can keep our shop vac clean by slipping a section of panty hose over the filter to keep large and small material from collecting in the folds of the filter. It gives you better pickup…
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky.
“Tin cans are great for carrying a quart bottle of oil under the hood of your car or pickup. Just find a tin can that’s large enough to hold a 1-qt. container and screw, wire or bolt it…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Overhead “creepers” that let you lie down while working from the top side of a vehicle aren’t new. But Dennis Fisher, Sisseton, S. Dak., has designed one that can be used to service almost any machine.
Read the complete story →From the archive · Full text
Feature story
Featured source:
When his Hot Shot portable pressure washer wore out, Rich Maus, Chandler, Ariz., turned it into a low-cost filtering unit that allows him to convert used motor oil into a diesel fuel additive for his semi trucks.
Read the complete story →From the archive · Full text
Reader shop tip
Greg Evans, Concord, Va.
“We replaced the rubber pivot on the blade on our New Holland Haybine with a tie rod end from a truck. No more problems.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jeff Roberts, Needville, Texas
“I use a magic marker to write down the oil filter number, oil capacity, drain plug size, or other maintenance information under the hood of my pickups, cars, and tractors. It eliminates having to crawl under them all…
Read the complete tip →From the archive · Full text
Reader shop tip
Eldred Stocks, Jordan, Minn.
“I found an easy way to remove ice buildup along our machine shed sliding door. Just lay a log chain out lengthwise outside the door. When ice and snow build up on top of the chain, all you…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
John M. Kiminski, North Brookfield, Mass.
“Here’s another idea: Several years ago I bought a $25 automotive electric fuel pump and put a length of gas line hose on both outlets. I’ve used it to drain out many a gas tank that needed repair…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
John M. Kiminski, North Brookfield, Mass.
“I made a portable gas tank out of a 1-gal. anti-freeze jug, a length of gas line hose and a metal tire valve stem. I first remove the core from the valve stem (on some stems you have…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“It lets me work from the top side of the engine - anywhere under the hood - with both my hands free,” says Wesley Linn, Mena, Ark., about his “top side” mechanic’s creeper.
Read the complete story →From the archive · Full text
Reader shop tip
Edwin Ruff, Moses Lake, Wash.
“To push another vehicle, tie an old tire to the front of your vehicle with a bungy cord. Then you can easily push another vehicle with no hard bumps. On corners or rough spots, you can give extra…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Robert Ingram, McArthur, Calif.
“I usually change my own oil in my vehicles and it was always hard to remember when the oil was changed last and what number the oil filter was. So now when I change oil and filter, I…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Suter, Altoona, Penn.
“When I recently had to take apart the front hub of my 1979 Ford F-250 4-WD pickup, a friend suggested that instead of buying the $35 wrench to take off the nut that I could make one out…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
This new U-joint puller for pto driveshafts lets you remove bearing cups quickly and easily without damaging the driveshaft, yokes, cups, or bearings, says Tiger Tool International, Inc., Sumas, Wash.
Read the complete story →From the archive · Full text
Reader shop tip
William E. Craycraft, Bloomingdale, Ind.
He rigged up a simple oiler for the chain at the top of his grain bin auger.
Read the complete tip →