Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Vehicles & Trucks

1127 shop tips and stories · page 13 of 19, newest issues first.

From the archive · Full text
Reader shop tip 1 of 2

H.J. Trahan

Individual tip 1 of 2 from this reader’s published contribution.
H.J. Trahan, Jennings, La.

“With old equipment, I always had trouble getting tires to pop onto the rim. I started using motor oil to make them slip on, but unfortunately when I tried that on my farm pickup and turned a corner,…

Read the complete tip →
From the archive · Full text
Reader shop tip 4 of 4

Ben Burlingame

Individual tip 4 of 4 from this reader’s published contribution.
Ben Burlingame, Charlton, Mass.

“We keep a 55-gal. drum in one corner of our garage to drain oil into. With all our trucks and equipment, it sure is nice to be able to put the oil in one place. When the barrel…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Allen Ahlbrecht

Individual tip 1 of 2 from this reader’s published contribution.
Allen Ahlbrecht, Hector, Minn.

“We had been having a lot of problems with wheel bearings on equipment, especially the smaller tag axles bolted to our trucks to get past road restrictions each spring. After switching to a synthetic grease, the problem went…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Marvin Kroontje

Individual tip 1 of 2 from this reader’s published contribution.
Marvin Kroontje, Magnolia, Minn.

“I use a 1/2-in. dia., 3-ft. length of galvanized water pipe - with the last foot curved - to tighten belts on vehicle alternators, power steering units and air conditioning units. It makes a great pry bar once…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

W.A. Gibbs

Individual tip 1 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.

“When I lost the ignition key to my 1958 Chevrolet 2-ton dump truck, I was able to come up with a simple, low-cost solution without ever touching the old ignition switch. It was a lot easier than putting…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

W.A. Gibbs

Individual tip 2 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.

“I used the same idea on my 1961 Deere 1010 dozer, except that on the dozer I installed an extra switch. I still use both switches. With the original switch I had trouble burning up ignition points. Now…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Dan Gray

Individual tip 2 of 2 from this reader’s published contribution.
Dan Gray, Dewberry, Alberta

“When I want to bleed brakes but don’t have any help, I use an air valve and a modified tire pump – the old cylinder style. I regu-late the air pressure to about 30 psi and brace the…

Read the complete tip →
From the archive · Full text
Reader shop tip

Harbor Products, Inc.

Harbor Products, Inc., Carson City, Nevada ph 877 847-2628 or 201 681-3648; www.rescuetape.com

This company re-cently introduced a new product called Rescue Tape. It’s made of a self-bonding silicone with no adhesive so when removed it never leaves any sticky residue like traditional adhesive tapes. When stretched and wrapped under tension,…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Bill Wilson

Individual tip 1 of 2 from this reader’s published contribution.
Bill Wilson, 44 Gable Road, Thompson Falls, Montana 59873 ph 406 827-3006)

“I mounted a pair of standard overhead chain hoists perpendicular to each other on the ceiling of my shop. Both hoists slide back and forth on separate trolleys. I’ve used them to put a new clutch in my…

Read the complete tip →