From the archive · Full text
Reader shop tip
Ed Panchyshak, Windsor, Ontario
“If you need an owner’s manual for an older model car or truck, there’s a company in California that can help. Call Faxon Auto Literature at 1-800-458-2734 or write to: 1655 East Sixth St., Corona, Calif. 91719. The cost is $10 plus $4.95 shipping.”
From the archive · Full text
Reader shop tip
David Buss, Clayton, Ill.
One of the hassles of operating most dry fertilizer spreader wagons is that you have to get on or off to set the wheel-driven fertilizer buggy gears by hand to put the rig in and out of gear. Buss solved the problem by welding a small hydraulic cylinder to brackets on the side of the tank and then connecting it to the length of chain used to lift the drive wheel off the ground wheel. Now, just a touch of the hydraulic cylinder raises or lowers the wheel.
“It’s convenient for transport and makes it nice when crossing wa-terways and the like,” notes Buss.
From the archive · Full text
Reader shop tip
Roland Schild, Greenview, Ill.
You’ll get a better grease job with an air-powered grease gun, according to Schild, who bought his gun at a NAPA auto parts store. He mounts the grease gun, which fits on top of a 5-gal. bucket of grease, on a 2-wheeler to make it easy to move around. It hooks up to a conventional air hose.
From the archive · Full text
Reader shop tip
Wayne Hutsul, Southgillies, Ontario
“Last winter the fan belt broke on my furnace. Not having a spare belt, I looked all over the farm for an extra one from another application. Then I recalled that panty hose or nylons can be used in an emergency. I dug out a pair of my wife’s panty hose and made up the length required, and then tied it down over the fan belt pulley and motor. It worked fine until I was able to get a replacement belt.” (Countryside Magazine)
From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Molnar, Leonard, Mich.
“I use a paint pen to write the size of wrench needed for the oil plug and type of filter needed under the hood of all my vehicles. This allows me to have the right tool when I go under the vehicle, saving time.
From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Molnar, Leonard, Mich.
“One other thing I do is to use dental tools to get into tight spots to clean. They’re strong and there’s nothing like them for certain jobs.”
From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Branum, New Madrid, Mo.
“My Caterpillar Challenger 65 had problems with the radiator getting clogged with dust. I solved the problem by mounting a steel plate at the front of the tractor under the big screen. It stopped the big fan from making a whirlwind that sucked dirt from the ground.
From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Branum, New Madrid, Mo.
“Another idea that works well for us is a seat I built that slides onto the tow hooks of my GMC 4-WD pickup. It rides low to the ground, extending out to the left side of the truck. We use it to flag fields for grading land. I use a Calc-N-Acre monitor to measure the distance for flags.”
From the archive · Full text
Reader shop tip
Allen & Linda Gullikson, Lonepine, Mont.
“This drill press ‘table saver’ lets you drill holes through without marring the drill press table. We used an 8-in. square piece of channel iron, welding four 3/4-in. bolts to the corners that are spaced to fit holes in the drill press table. You can clamp your work to the table saver with a vise grips or small C-clamp. When you get too many holes in it, you just throw it away and make another one.”
From the archive · Full text
Reader shop tip
Roland Schild, Greenfield, Ill.
Schild made a spring-loaded, cantilevered work light that’ll extend 18 ft. out from the wall.
Equipped with a 300 watt halogen bulb, he simply patterned the light after a small desk lamp. He took measurements off the small lamp and increased them proportionately, using 1-in. sq. steel tubing and three garage door springs to hold it in place. The light pivots on the end of the hinged arm, and it swings 180°, so it can be positioned at almost any angle. Schild built another light for another wall of his shop that reaches out 12 ft.
From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Jim Kaufman, Moundridge, Kan.
“Over time, field cultivator shanks tend to straighten out so that sweeps no longer run level. Rather than attempting the difficult task of recurving the shank, I bend the sweep. The method I use is to clamp the pointed end of the sweep in a vise. Then I slip a 3 to 4-ft. length of pipe over the shank portion of the sweep and let the pipe hang free. Using a torch, I heat the shank at the point where it meets the body of the sweep. The weight of the suspended pipe causes the sweep to slowly bend. With a little practice, sweeps can be easily and safely bent to any desired angle. I’ve used this technique on all sizes of sweeps and have never had a sweep break at the point at which it was bent.
From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jim Kaufman, Moundridge, Kan.
“An inexpensive method of building a high volume air compressor is to use a small compressor and a large volume tank. I use a 300-gal. tank off an old NH3 applicator. These tanks are cheap, fairly readily available, and heavily built. To save shop space, the tank can be placed outside. In the past I used a piston-type automotive air conditioning compressor powered by a 2-hp. motor. But under heavy use these compressors have a limited life since they rely on freon for internal cooling. When used as an air compressor, they eventually overheat. To avoid this problem, I switched to a compressor from an ammonia rather than a freon system. These compressors can be found in old locker and meat processing plants. The compressors have fans and fins for air cooling and are heavily built. For an investment of approximately $150, I now have a compressed air system that handles any air tool.”
From the archive · Full text
Reader shop tip
Tom Schmitz, Harlan, Iowa
If you have trouble getting sweeps to penetrate hard ground, fiddle with the bolts on top of the sweeps, says Schmitz. He puts washers behind the sweeps, tilting the sweep forward a bit. He’s made the modification on his Deere 875 cultivator.
“It changes the pitch on them. Real easy and inexpensive.” (Iowa Farmer Today)
From the archive · Full text
Reader shop tip
Francis Roberts, Seligman, Mo.
“My simple corrugated metal cutter is a great way to cut through corrugated sheet metal roofing or siding, whether you’re cutting straight across or at an angle,” says Roberts, who made his metal cutter out of scrap materials.
He made it with four 2 by 4’s and two 1-in. boards. The bottom two 2 by 4’s nail to the top of the two 1-in. boards in an “H” configuration, spaced only about 1/8 in. apart. The top two 2 by 4’s fit over the bottom two 2 by 4’s. Four bolts go down through the 2 by 4’s and the bottom 1-in. boards.
A long piece of galvanized wire is anchored at one side of the unit. A handle is tied to the loose end.
To make a cut, you simply slip a piece of sheet metal between the four 2 by 4’s, and then tighten down the four bolts. Then you loop the wire under the metal and pull it up between the 2 by 4’s on the other side of the metal. When you pull back on the wire, it’ll cut right through the metal.
“I recommend using oak 2 by 4’s on top that have good square edges to make a cleaner cut,” says Roberts, who lays the cutting frame down flat on the ground and stands in the middle of the 2 by 4’s when pulling up on the wire.”
From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky.
“Tin cans are great for carrying a quart bottle of oil under the hood of your car or pickup. Just find a tin can that’s large enough to hold a 1-qt. container and screw, wire or bolt it under the hood in an out-of-way place that’s easy to get at.”
From the archive · Full text
Reader shop tip
Alice & Robert Tupper, Canton, S. Dak.
“We’ve discovered we can keep our shop vac clean by slipping a section of panty hose over the filter to keep large and small material from collecting in the folds of the filter. It gives you better pickup longer.”
From the archive · Full text
Reader shop tip
R.S. Burrow, Wilson, Texas
“I made a gated irrigation pipe puller when I hurt my back in 1980 and still use today. It consists simply of a 32-in. length of 3/8-in. dia. rod with a 4-in. J-shaped hook on one end and a 4-in. straight handle on the other. You can pull pipe apart at the joints as well as put it back together without having to bend over. It’s the handiest tool I’ve ever come up with.”
From the archive · Full text
Reader shop tip
Marion Calmer, Alpha, Ill.
A Rapid-Reel air hose reel that bolts to the top of Marion’s 3 1/2 hp, 15 gal. portable compres-makes it a lot easier to use air tools in his shop. He purchased the reel at his local TSC store. The reel carries 100 ft. of extra hose but Calmer uses only 50 ft. That’s plenty to reach any corner of his shop.
From the archive · Full text
Reader shop tip
Al Kelley, Athens, Texas
“We specialize in replacement starters for Belarus tractors. Our starters are more reliable and cost less than the ones made by Belarus, which have lots of problems. We adapt new Delco starters made for 6.2-liter GM diesels to fit all Belarus tractors. Cost is $275 to $350. Also, if an armature ever goes out on one of our starters, it costs just $40 to $50 to re-pair.” Contact: FARM SHOW Followup, Kelley Industries, 412 B South Palestine, Athens, Texas 75751 (ph 800 256-2142 or 903 675-8311, fax 4594).
From the archive · Full text
Reader shop tip
Leonard Donovan, E E Donovan & Sons, Mallorytown, Ontario
“Our Deere 3130 (2840 model in U.S.) was a hard starter in cold weather. So I bought new higher-cranking batteries than the Deere originals and wired them up differently to solve the problem. I used two new 950 cold cranking amp batteries. I then ran separate lines from each battery directly to the starter instead of from one battery to the next and then to the starter. The engine cranks faster and longer and starts easier.”
From the archive · Full text
Reader shop tip
Ernest Wagner, Delta, Ohio
“You can make an older IH tractor steer like a brand new Cadillac with a power steering system like the one I made for my 1939 Model A. The identical design could probably be used on any Farmall A built between 1937 through the mid-1940’s since they all had the same manual steering system.
“I got a power steering control unit and hydraulic cylinder off a junked Massey combine and a power steering pump off a car. I removed the tractor’s steering shaft and attached the combine’s power steering unit to the tractor’s steering wheel. I mounted the power steering pump on the side of the engine and belt-drive it off a pulley on the generator. I mounted the ram end of the hydraulic cylinder on the front axle and the rear end on the tie rod. I plumbed the system together with 3/8-in. dia. copper tubing.
“It cost only about $50 and works like a dream.”
From the archive · Full text
Reader shop tip
Dave Waldner, Shaunavon, Sask.
“We were constantly breaking knife guards on our four Versatile 400 swathers when harvesting lentils. So we came up with a money-saving way to recycle guards with one usable side.
“We cut these guards apart in the center and use a home-built jig, which is set up to assure bolt holes are properly spaced, to weld the good guards back together. We estimate we’re saving $800 in a year in replacement costs.”
From the archive · Full text
Reader shop tip
Joe Ross, Waynesburg, Pa.
“We specialize in rebuilding magnetos for 1920’s to mid 1950’s Farmall tractors. We use only stock parts when replacing ignition coil windings, which will cost anywhere from $40 up to $180 depending on which brand magneto your tractor was equipped with. We also replace magnets, condensor or points if necessary. The complete package runs from $100 to $300. All you have to do is unbolt the magneto and bring or send it to us at: Ross Tractor Sales, 40 S. Woodland Ave., Waynesburg, Pa. 15370; ph 412 627-6966.”
From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Brian Yokimas, East Selkirk, Manitoba
“When it comes to heading off potential mechanical problems with your combine, there’s nothing quite as effective as an ordinary mechanic’s stethoscope.
“You can buy one at any good auto parts or tool supply store for around $30 (U.S.). I’ve used one ever since I began farming 27 years ago and wouldn’t be without it. Thanks to the stethoscope, my 13-year-old New Holland TR 85 combine got through another 1,000-acre small grain harvest last year without a hitch. I use the 12-in. probe on the stethoscope to listen to every bearing as I run the machine real slowly. A bearing in good condition will make a smooth whir-ring sound, while one that needs replacing will growl or clunk. You’ll catch a bad bearing much faster this way.
From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Brian Yokimas, East Selkirk, Manitoba
“You can keep the retracting fingers on the feeder drum in your combine from wearing prematurely by making a simple modification. I’ve done it on 10 used combines in my 27 years of farming and know it re-ally helps prolong finger life.
“I simply change to smaller drive sprockets, usually the smaller of the two drive sprockets. I’ve found a 20 percent re-duction in size from the original is ideal. For instance, if the drive has a 20-tooth sprocket, I replace it with a 16-tooth sprocket.
“With this modification, the machine runs quieter and should last 20 percent longer. If the average combine is used 15 years, that translates to three extra years of use. All for just a couple hours work.”
From the archive · Full text
Reader shop tip
David Schlies, Denmark, Wis.
“On those bitterly cold below zero winter days when I’ve got manure to haul, I’ve come up with a low-cost way to keep it from sticking to metal spreaders, making both spreading and clean-up a breeze.
“I simply coat the inside steel surfaces of my New Idea 363 320-bu. spreader with diesel fuel or waste oil. I apply a thin coating with an old broom. Works really well.”
From the archive · Full text
Reader shop tip
Steve Pope, Brown’s Summit, N.C.
“We’re America’s largest distributor of replacement parts for lawn and garden power equipment. We handle parts for everything from lawn tractors to string trimmers. Everything’s listed in our free 500-page catalogue.” Contact: FARM SHOW Followup, Dixie Sales, 5920 Summit Ave., Brown’s Summit, N.C. 27410 (ph 800 753-4943; fax 800 535-2862, or 910 375-7500; fax 910 621-3555).
From the archive · Full text
Reader shop tip
Dennis E. Heck, Pendleton, Ind.
“Many people do not know there’s a special welding rod on the market for extracting broken-off bolts. Called X-TRACT-ALLOY (X-ERGON Co., 1570 East Northgate Blvd., P.O. Box 152102, Irving, Texas 75012; ph 800 527-7782 or 214 438-0306), it’s ideal for welding a nut to a broken bolt because it flows down into the threads but won’t adhere to the equipment that you’re pulling the bolt out of. You simply lay it on top of the broken bolts, strike an arc on the bolt, and fill the nut. The rod is available in 3/16, 5/32, 1/8, 3/32 and 5/ 16 in. dia. Sells for around $50 per pound.”
From the archive · Full text
Reader shop tip
Duane Miller, Middlebury, Ohio
“If you have an old windmill that you would like to see in good operating condition, I can help. I sell, service, install, repair, restore, overhaul, even manufacture parts for old windmills, virtually any model ever built. I’ll travel just about anywhere to work on them, too. A windmill requires an annual oil change and greasing of all external moving parts. The most common problem I fix in the shop is replacing bearings and shafts, which costs approximately $600 to $1,000. House calls cost more.” Contact: FARM SHOW Follwup, Sam’s Windmill Service, 14386 Co. Rd. 14, Middlebury, Ind. 46540 (ph/fax 219 825-2877).
From the archive · Full text
Reader shop tip
John Richardson, New Lothrop, Mich.
“Tired of paying an arm and a leg to buy specially manufactured spark plugs to fit antique farm machinery?
“I’ve come up with an adapter that lets you use an ordinary automotive spark plugs in your old engines. An ordinary automotive spark plug screws into the adapter, which then screws into the engine. Inciden-tally, I’ve had many orders for adapters for Deere “hit and miss” stationary engines, which require my 1/2-in. NPT adapter.
“Three sizes are available - 18 mm, 7/8 in. and 1/2 in. for $5 apiece plus $2 S&H. (Orders of 50 or more are $4 apiece).” Contact: FARM SHOW Followup, R.E.A.M. Corp., P.O. Box 311, New Lothrop, Mich. 48460 (ph 517 743-4360).
From the archive · Full text
Reader shop tip
Harlan Olson, Elbow Lake, Minn.
“I made this handy swing-out shop light a few years ago.
“I started with a 10 by 12-in., 500-watt quartz outdoor light. I mounted it on track rollers off a sliding door, threading heavy-duty wiring through a 16-ft. length of 1 1/2-in. dia. electrical conduit. The conduit attaches to a swivel that bolts to a stud on one wall of my shop. The light swings 180°. The light hangs about 10-ft. above the floor. The track wheels permit me to pull the light to the farthest corners of my shop, from work bench to drill press to second work bench, etc. It works better than I’d ever dreamed and is particularly useful for working on engines.”
From the archive · Full text
Reader shop tip
Ed Allspach, Mt. Pulaski, Ill.
“We could only use our 1941 IHC M for pulling our 6-row cultivator until we built a quick-tach 3 pt. hitch for it. Now we use it all the time to pull our 7-ft. sickle mower and 9-ft. disk mower.
“We made the 3-pt. using lift arms off an old Ferguson tractor and Cat # 2 arms off a Case tractor. It’s raised by a 4-in. hydraulic cylinder with 18-in. stroke that we clamped between the rear axle housing and top link. The quick-tach mechanism is store-bought. The whole system cost virtually nothing to build and gives us a tractor that’s 100 times more useful than before.”
From the archive · Full text
Reader shop tip
Walter S. Pittman, Sury, Va.
Walter and his son came up with a quick and easy way to change chaff separator trays on their early 1980’s Massey-Ferguson 750 combine.
“Those galvanized pans are heavy and have to be slid in and out just so. There’s hardly any room inside the machine to work,” he says.
“We made rails out of 1 1/ 4-in. angle iron that bolt to each side of the machine and act as guides for taking pans out and putting them in again. They turn what used to be a 1 1/2-day job into a 1/2-day job.”
From the archive · Full text
Reader shop tip
J.E. Williams, Windsor, Mo.
“I re-cently came up with a neat idea for painting wheel rims without getting any paint on the tires. First, I deflate the tires and push the beads in a little. Then I lay a large piece of paper over the wheel rim and run my thumb around the rim to make an impression on the paper. Then I cut out the curves and slip the paper under the rim.’’