Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 20, No. 3 (1996)

Vol. 20, No. 3 (1996)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–32

47 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Brett Gettings

Brett Gettings, Gettings Farm, Fieldon, Ill.

“In a recent issue of FARM SHOW, a North Dakota farmer detailed problems he was having with his 1987 Deere 1610 27-ft. single depth control chisel plow. I have had some experience with this problem on similar equipment and would like to make a suggestion. Check in the machine’s parts manual to see if the wing lift cylinders (not the ones that fold it up) are supposed to be different sizes (diameter). If so, change the sides, putting the left on the right and the right on the left. It’s possible the dealer put them on incorrectly when doing setup.”

From the archive · Full text
Reader shop tip

Carroll Bantz

Carroll Bantz, Rowley, Iowa

“One modification we made to our shop was to mount a bank of old chicken house nests along one wall. The unit is 10 ft. long by 4 ft. high and each nest is 1 ft. square, so there are 40 boxes in all. I use them as bolt and nail bins. Each box is clearly marked with a marking pencil as to what’s inside.”

From the archive · Full text
Reader shop tip

Richard D. Peden

Richard D. Peden, North Manchester, Ind.

“When the muffler on our 3-wheeler rusted out, I welded the brackets from the rusted-out muffler to a muffler for an IH “B” tractor. For under $20 I put together a muffler that works fine. A new one would have been $70.”

From the archive · Full text
Reader shop tip

R. Berhow

R. Berhow, Osceola, Wis.

“We had problems with the notched rings that hold the wheels on the shafts of our Farmhand wheel rake. They’re made of cast iron, which was a poor choice. For one thing, replacements are too expensive. We substituted bearing retainers made of steel and we’ve never had a problem again.”

From the archive · Full text
Reader shop tip 1 of 2

Larry Losing

Individual tip 1 of 2 from this reader’s published contribution.
Larry Losing, Baker, Mont.

“The 2-in. shovels on our Deere 9350 hoe drills don’t last very long. We cut the shovels off straight and then weld on pieces of spring leaf steel cut off automotive springs. We sharpen the pieces and hard surface them. Then they last much longer.

From the archive · Full text
Reader shop tip 2 of 2

Larry Losing

Individual tip 2 of 2 from this reader’s published contribution.
Larry Losing, Baker, Mont.

“Another modification we made was installing a 6-71 Detroit diesel in our 1350 Minneapolis Moline. The old engine had problems. This fix works well.”

From the archive · Full text
Reader shop tip

James Johnson

James Johnson, Glade Spring, Virg.

“We made a tool that works great to remove injectors on Deere engines. You just take an old socket and cut it in half and weld a short length of pipe in the middle. Then cut a slot in one side to make room for the bleed-off line.”

From the archive · Full text
Reader shop tip

Virgil Storm

Virgil Storm, Lucas, Iowa

“To pre-vent damage to disc brakes and calipers on our Gleaner combine, we made mud shields that go over the brakes. They keep mud out of the brakes, preventing wear and keeping the brakes from freezing in winter.”

From the archive · Full text
Reader shop tip 1 of 2

Jon Becker

Individual tip 1 of 2 from this reader’s published contribution.
Jon Becker, Cumberland, Wis.

“Instead of replacing rusted-out silage handling conveyors, we lined them with plastic.

From the archive · Full text
Reader shop tip 2 of 2

Jon Becker

Individual tip 2 of 2 from this reader’s published contribution.
Jon Becker, Cumberland, Wis.

“Another good idea we had was moving our wet holding bin for corn drying inside our machine shed and installing a small dump pit outside with a used leg that moves grain to the holding bin. Works great. Lets us handle grain in all kinds of weather.”

From the archive · Full text
Reader shop tip

John Voigt

John Voigt, Avon, S.Dak.

“I built a parts washer from an old water softener barrel and a salvaged electric fuel pump. The plastic barrel had a screen platform at the bottom. I cut the top half of the barrel off and mounted the bottom half on a stand. The fuel pump circulates cleaning fluid through a 1/2-in. rubber hose. The only out-of-pocket expense was for a 12-volt power supply and No. 1 diesel fuel used for fluid.”

From the archive · Full text
Reader shop tip

David K. Curtis

David K. Curtis, Sedalia, Colo.

“We had a problem with our Hesston 500 swather. It was making fairly bunchy wind-rows. We solved the problem by changing the angle of the header and installing ‘strip-pers’ for the auger to run against to knock crop material off. In addition, we made header skids out of D-6 Caterpillar track pads and worn-out dozer blade cutting edges.”

From the archive · Full text
Reader shop tip 1 of 2

Dale Oldenberg

Individual tip 1 of 2 from this reader’s published contribution.
Dale Oldenberg, Medford, Wis.

“I make replacement machinery control lever knobs by using ping pong balls as forms and filling them with steel epoxy glue.

From the archive · Full text
Reader shop tip 2 of 2

Dale Oldenberg

Individual tip 2 of 2 from this reader’s published contribution.
Dale Oldenberg, Medford, Wis.

“We had problems with U-joint failure on our older Deere 35 forage chopper. After we replaced it with an extra heavy duty joint, we had no more problems.”

From the archive · Full text
Reader shop tip

Richard Keeney

Richard Keeney, Cuyler, N.Y.

“I turned a 15-gal. plastic barrel into a handy holder for redi-rod and flat stock. I cut the top off and then cut out a circle of wood with holes in it to fit the top of the barrel. The handle on the top edge of the barrel makes it easy to carry around.”

From the archive · Full text
Reader shop tip

Michael

Michael, Midland, Tex.

“I recently read in ‘Best of FARM SHOW’ about the man from Liberal, Mo., who made axle extensions for his Deere 4555 MFWD tractor. The modification was expensive - about $800 per side. There’s a much easier, and less expensive, way to accomplish the same thing. A machine shop can build a spacer that bolts between the front hub and wheel. They’re similar to the spacers used on rear dual wheels. They can be moved from one tractor to another easily. They also make the tractor turn much sharper. We have a 12-in set of spacers on our 8300 Deere and they work great. There are a number of people in our area who are running spacers like these in sizes ranging from 12 to 20 in. in width with no complaints. The new 8000 series Deere tractors are different from the older models, yet the same spacers will fit, unlike making an axle modification.”

From the archive · Full text
Reader shop tip

Andrew Szurek

Andrew Szurek, Minneapolis, Minn.

“I got an old refrigerator from my neighbor and I felt the frame was too good to just throw away. So I got the idea of turning it into a parts cabinet to hold odd parts, tools, and other miscellaneous items. I used angle iron to make runners for the drawers to slide in. Heavy sheet metal screws hold the angle iron runners in place. I used 1/4-in. plywood to make the bottoms of the drawers and 3/4-in. pine to make the sides. The drawers slide just fine.

“I mounted the entire cabinet on an angle iron frame fitted with old iron wheels. It’s been so handy around my shop that I made another one to have at my lake cabin.”

From the archive · Full text
Reader shop tip 1 of 2

Robert Tupper

Individual tip 1 of 2 from this reader’s published contribution.
Robert Tupper, Canton, S.Dak.

“Here’s an easy way to make a straight cut on pipe or round stock. Just wrap a square sheet of paper around the pipe and line it up evenly. The edge will be square to the surface of the pipe. Just mark the edge and it’ll be easy to make a square cut.

From the archive · Full text
Reader shop tip 2 of 2

Robert Tupper

Individual tip 2 of 2 from this reader’s published contribution.
Robert Tupper, Canton, S.Dak.

“You can make a simple screw slot cleaner out of a hack saw blade. Cut or break off a 4-in. piece of blade and grind one end down to a blunt point. Slip it into the end of a 4-in. long, 3/4-in. dia. piece of wood dowel. Drill 3/32-in. holes through the dowel and blade and put a nail or screw through to hold it in place. This tiny tool works great for cleaning paint, varnish or rust out of screw slots.”

From the archive · Full text
Reader shop tip 1 of 2

Wayne Hagen

Individual tip 1 of 2 from this reader’s published contribution.
Wayne Hagen, Lake Alma, Sask.

“I’ve designed and built 5 machines for farm shops and machine shop operators. Three of my machines have already been featured in FARM SHOW: a 4-ft. brake and shear combination, a punch and bar shear, and an iron roller. My latest two machines are a 12-in. deep throat punch and a hydraulic tubing bender.

“The deep throat punch has a simple design that’s easy to build and would fit anyone’s budget. I used 1 1/2 in. steel plate for the body and most other parts. For the hydraulic cylinder I used a 30-ton ram built for hydraulic presses. The punch has a foot operated valve to give hands-free operation. It’ll punch a 1-in. dia. hole in 3/8-in. steel plate or a 3/4-in. hole in 1/2-in. plate. It will accept conventional punches so many shapes and sizes can be used.

From the archive · Full text
Reader shop tip 2 of 2

Wayne Hagen

Individual tip 2 of 2 from this reader’s published contribution.
Wayne Hagen, Lake Alma, Sask.

“The problem with most small tubing benders is that they’re hand-operated and must be upright to work and in tight spaces you can run out of room. They’re also labor intensive. My bender is built to work horizontally with an electric-driven hydraulic unit. It takes various tubing dies from 1/2 to 1 1/2-in. and I also made dies for square tubing and flat iron. It works great for bends on corral panels and other such jobs. It works best with standard wall round and square tubing up to 1 1/2-in. dia. and up to 2-in. flat iron.

“All my machines are built to work on an open center hydraulic system. They can all be connected to one central power unit. I can make detailed do-it-yourself plans available for any of them.”

From the archive · Full text
Reader shop tip 1 of 2

Michael Casson

Individual tip 1 of 2 from this reader’s published contribution.
Michael Casson, Chandler, Ind.

“I used an old stainless steel laundry room sink, an old cabinet door, and a 30-gal. steel barrel to make an inexpensive parts washer. The barrel contains cleaning fluid. A pump mounted on an angle iron frame bolted to the bottom of the sink pumps fluid through a hose up into the sink. The cabinet door is used as a lid and is hinged on back so I can flip it up or down. The angle iron frame keeps the sink centered over the barrel. The 2 by 3-ft. sink is big enough to wash engine heads and blocks. A screen in the sink drain filters out big pieces of dirt. Dirty fluid drains out the bottom of the sink and back into the barrel. I change the fluid twice a year.

From the archive · Full text
Reader shop tip 2 of 2

Michael Casson

Individual tip 2 of 2 from this reader’s published contribution.
Michael Casson, Chandler, Ind.

“I got tired of having to open and close gates all the time on my horse corral so I came up with a simple solution. I left an opening by the gate that’s just wide enough so that I can turn sideways and slip through. My horses are too big to go through it.”

From the archive · Full text
Reader shop tip 1 of 2

Joe Staadegaard

Individual tip 1 of 2 from this reader’s published contribution.
Joe Staadegaard, Lynnville Farm Equipment, Rt. 1, Windham Centre, Ontario, Canada (ph 519 426-4416)

“We’ve had a lot of problems with front wheel shimmy on Massey Ferguson 165 and 175 tractors, usually during road travel. I solved the problem by installing two automotive shocks under the front axle, with one end of each shock attached to the front axle and the other to the center steering pivot. it will prevent shimmying and also prevents the tire rod ends and other steering parts from wearing out as fast as they do now.

“I’ve made this fix on several tractors over the last couple years and received nothing but praise. I’ve even installed the shocks after rebuilding the steering system. We now have the parts available as a do-it-your-self kit with complete instructions. Sells for $125 (Canadian). Dealer inquiries welcome.

From the archive · Full text
Reader shop tip 2 of 2

Joe Staadegaard

Individual tip 2 of 2 from this reader’s published contribution.
Joe Staadegaard, Lynnville Farm Equipment, Rt. 1, Windham Centre, Ontario, Canada (ph 519 426-4416)

“We also sell a carburetor kit for old Ferguson tractors, models 20-80 and 20-85 that have the English model 24T-2 carburetors. The kit has a throttle shaft, needle and seal, floats, gaskets, fiber washers and instructions. Since all parts are custom-made, they’re not cheap but they’ll let you get a little more life out of the old Fergies.”

From the archive · Full text
Reader shop tip

Damon Reed

Damon Reed, Cane Hill, Ark.

“Round bale feeders rust out. To solve the problem I cut 16-in. metal strips out of an old water tank and welded them around the bottom. Took just an hour and a half. The bale feeder is now much stronger.”

From the archive · Full text
Reader shop tip

Marvin Finger

Marvin Finger, Rozel, Kan.

“When I was working on a big engine and it came time to put the piston and new ring back in the cylinder hole, I couldn’t find a ring compressor that was big enough. I solved the problem by using two large worm screw hose clamps. I unscrewed them all the way out and then screwed the ends together to make one large clamp. I used the wooden handle on a 3-lb. hammer to carefully tap the piston down. The hose clamp was wide enough to compress two rings at a time.”

From the archive · Full text
Reader shop tip 1 of 2

Jeff Roberts

Individual tip 1 of 2 from this reader’s published contribution.
Jeff Roberts, Needville, Texas

“I mounted Deere 77 cotton stripper plant guides on my International 214 cotton picker units in order to make them ‘self cleaning’ in morningglory-infested fields. The Deere guides are much steeper than the IH guides so vines are more likely to slide off them whenever I back up at the end of the field.

From the archive · Full text
Reader shop tip 2 of 2

Jeff Roberts

Individual tip 2 of 2 from this reader’s published contribution.
Jeff Roberts, Needville, Texas

“I use a magic marker to write down the oil filter number, oil capacity, drain plug size, or other maintenance information under the hood of my pickups, cars, and tractors. It eliminates having to crawl under them all the time at oil changing time in order to find out what tools or parts are needed. I write down the information in a convenient area that’s free of grease, and oil.”

From the archive · Full text
Reader shop tip 1 of 2

Jeff Krehbiel

Individual tip 1 of 2 from this reader’s published contribution.
Jeff Krehbiel, Hydro, Okla.

“We have an old-style Richardson sweep plow equipped with 5 and 5 1/2-ft. sweeps. The U-joint knuckles on the rockshaft often break and new ones are no longer available. To solve the problem we remove the knuckles completely and put 3 by 8-in. hydraulic cylinders plumbed in series on each section. Works great.

From the archive · Full text
Reader shop tip 2 of 2

Jeff Krehbiel

Individual tip 2 of 2 from this reader’s published contribution.
Jeff Krehbiel, Hydro, Okla.

“My dad had trouble with the glow plug sensor on his 1988 GM Suburban equipped with a 6.2-liter diesel engine. After the dealer changed glow plugs and a sensor with no results I finally found the problem - a loose ground to the sensor. It cost $225 to repair. It should have cost 25 cents at the most.”

From the archive · Full text
Reader shop tip 1 of 2

Dan Jedlicka

Individual tip 1 of 2 from this reader’s published contribution.
Dan Jedlicka, Central City, Iowa

“An inexpensive hydraulic press can be made using two 10-in. long, 3-in. wide channel irons and connecting them with two 2-ft.

long, 3/4-in. dia. threaded rods. Simply position it upright in a vise and put a bottle jack between the channel iron pieces. The rods make it easy to adjust for size as needed.

From the archive · Full text
Reader shop tip 2 of 2

Dan Jedlicka

Individual tip 2 of 2 from this reader’s published contribution.
Dan Jedlicka, Central City, Iowa

“My Ford 5-bar, 3-pt. pto-powered hay rake does a great job of raking hay but also makes a good tender for fluffing up rained-on windrows. Simply criss cross the drive belt which causes the bars to turn backward. It kicks hay just enough to open the smashed windrows.”

From the archive · Full text
Reader shop tip

Wallace E. Keller

Wallace E. Keller, Mt. Horeb, Wis.

“I have an 8-ft. long, 3-pt. blade that’s quite heavy. To make it easier to mount I attach a pair of chains to each end and hang it from a stand that I built from a length of pipe and steel rods. I put a car jack under the hitch arms to make it easy to hook up to my 3-pt.”

From the archive · Full text
Reader shop tip

Leon Harbur

Leon Harbur, Kirksville, Mo.

“You can fill a puncture hole in a tractor tire with black silicone to keep mud and water out. It works well and will last a long time. It also works for weather cracks.”

From the archive · Full text
Reader shop tip

Wade Hancock

Wade Hancock, Cullman, Ala.

“The fuel line on my Ford 5600 tractor began leaking at the tank - the solder joint had cracked. Rather than removing the tank I simply drained it and fixed it with a product called JB Weld. It’s like an epoxy glude and worked very well.”

From the archive · Full text
Reader shop tip

Daniel Diener

Daniel Diener, Melrose Park, Ill.

“B’Laster industrial-strength products have saved me a lot of headaches, time, and money for all my maintenance and repairs. The company makes penetrating catalysts, air-tool oil-conditioners, engine life extend-ers, silicone lubricants, citrus and aqueous degreasers, small engine tune-up products, etc. I like the products so well that I became a distributor (10620 Nevada Ave., Melrose Park, Ill. 60164).

From the archive · Full text
Reader shop tip

Galen Winger

Galen Winger, St. Joseph, Mo.

“When I built my shop I had to grade one side down 3 ft. in order to make it level. I poured a 4-ft. high concrete wall and welded several short lengths of 10 by 12-in. H-beam end to end about 20 ft. long, then cut them in half to make two ‘T-beams’. I used 4 1/2-in. steel pipe for posts and spaced them 4 ft. apart. I placed the ‘T-beams’ on top of the wall and posts to make ramps that I use to service cars. I later doubled the width of one ramp to accommodate small and mid-size cars. Works great. I find that I service my cars more often now because they’re so easy to service - I don’t have to crawl under them.”

From the archive · Full text
Reader shop tip 1 of 2

Paul Donley, Jr.

Individual tip 1 of 2 from this reader’s published contribution.
Paul Donley, Jr., Capron, Ill.

“Old stainless steel bulk milk tanks make great cattle water tanks. They never rust and are double-walled to help keep water from freezing . Also, they’re built strong. I have three of them on my farm.

From the archive · Full text
Reader shop tip 2 of 2

Paul Donley, Jr.

Individual tip 2 of 2 from this reader’s published contribution.
Paul Donley, Jr., Capron, Ill.

“I mounted a 3-speed car transmission on my feeder wagon so that I can run it slow into my bunk feeder or fast for fenceline feeding.”

Shop feature stories

From the archive · Full text
Feature story

Pressure Washer Converted To Filter For Used Motor Oil

Featured source:

When his Hot Shot portable pressure washer wore out, Rich Maus, Chandler, Ariz., turned it into a low-cost filtering unit that allows him to convert used motor oil into a diesel fuel additive for his semi trucks.

“It’s an inexpensive source of fuel that also solves a disposal problem. I use it whenever I change oil,” says Maus, who operates a commercial trucking business.

He stripped the 3-wheeled pressure washer down to the 110-volt electric motor and pump. He mounted two spin-on fuel filters (designed for Cummins diesel engines) onto lengths of angle iron welded to one side of the cart. The filters plumb into the pressure side of the pump. To use the rig he starts the pump and puts one end of a rubber hose from the suction side of the pump into the oil drain pan. The pump draws oil out of the pan and pumps it through a rubber hose into the first fuel filter. From there it goes through a short length of hose to the second filter and then out a hose to a storage tank.

“I’ve been using it on the Cummins NTC and Cat 3406 diesel engines in my semi trucks for over 10 years with no problems at all,” says Maus.

“The filters catch all large contaminants that might harm a diesel engine’s fuel pump or injectors. Used motor oil can’t exceed .05 percent of the total fuel volume. It has fewer btu’s than diesel fuel but I’ve never been able to recognize any loss of power because the amount I add is so small. There might be more smoke in the exhaust, but it’s hardly noticeable. I use it on all my diesel trucks and filter about 100 gal. per year. I’m sure that filtered used oil could also be used on diesel tractors.

“My only expense was for the two fuel filters which cost about $8 apiece. If you’re going to burn waste oil in an off-road tractor or stationary engine you don’t have to pay taxes on it. However, if you’re going to use it in an on-highway vehicle you do have to pay highway taxes on it. Contact your state to find out about the paperwork that’s required.”

Contact: FARM SHOW Followup, Rich Maus, 20510 S. Greenfield, Chan-dler, Ariz. 85249 (ph 602 988-1213).

From the archive · Full text
Feature story

Heavy Duty Rolling Shop Crane

Featured source:

“My homemade shop crane makes it easy and safe to move heavy loads virtually anywhere inside my shop,” says Daryl Scheer, Mapleton, Iowa. The frame of the 4-wheeled crane was built from scrap steel. It’s equipped with a 3-ton chain hoist that rolls back and forth on the top I-beam. Both ends of the crane mount on wheels so it can be rolled anywhere in the shop.

“It’s one of the handiest tools in my shop,” says Scheer.

“I looked at commercial shop cranes and the more I looked, the more I decided that I could build my own. It’s 16 ft. wide and 14 ft. high but can be raised or lowered by jacking it up and changing the position of a pin in each leg. I’ve even used it to pull cabs off tractors.”

The sides are made from 4 by 7-in. steel tubing salvaged from the frames of old row crop cultivators and the top is made from a 4 by 8-in. steel I-beam salvaged from an old bridge. He useed 2 1/2-in. sq. steel tubing to make corner braces and 4-in. dia. pipe to make the legs.

Contact: FARM SHOW Followup, Daryl Scheer, 310 S. 8th St., Mapleton, Iowa 51034 (ph 712 882-1439).

From the archive · Full text
Feature story

Hammer Makes Nail-Starting Easy

Featured source:

A magnetized nail holding slot at the top of this new hammer makes it easy to start any nail even if only one hand is free. Simply fit the nail into the slot and drive it in.

The new hammer also features a trian-gular head that the manufacturer says is easier to use in corners and is better balanced.

Comes with a choice of head weights ranging from 10 to 30 oz.

Start at $23.95 plus S&H. Contact: FARM SHOW Followup, Ted Hammers Inc., 6152 Mission Gorge Road, Suite G, San Diego, Calif. 92120 (ph 800 645-2434 or 619 584-1190).

From the archive · Full text
Feature story

Stick-On Magnets Boost Oil Filter Performance

Featured source:

Putting magnets on oil filters to pull out metal filings seems like such a simple idea that you have to wonder why it has never caught on.

In recent months we’ve come across two companies that make stick-on magnets designed to boost oil filter performance.

Zoor Inc., Redmond, Wash., says its new “Super Magnaforce Oil Magnet” simply snaps onto the bottom of any filter. It can be reused every time you change oil.

Three sizes are available. Size A for light engines sells for $21.95; size B for semi trucks and tractors sells for $29.95, and size C for automatic transmissions and fuel tanks sells for $11.95.

Contact: FARM SHOW Followup, Zoor Inc., 14572 N.E. 95th St., Redmond, Wash. 98052 (ph 206 861-8400).

Another approach is to attach new “rare-earth” super magnets to the sides of filters. TBO Advisor, an aircraft engine publication out of Wilton, CT, recommends attaching four magnets per filter.

“They’re small enough to fit onto the filter but powerful enough to suck ferrous wear particles out of the oil,” says a company spokesman.

“Conventional magnets are too weak to do the job - most of the magnetic field passes harmlessly into the filter’s steel shell. Rare earth magnets are several times stronger than conventional magnets and are a relatively new development in the electronics industry. They’re becoming widely used in stereo speakers and in reduced size electric motors.

“If you cut open the filter after magnets have been used on it you’ll find a pasty, fine build-up of metal particles where the magnets were attached. The magnets can be reused every time you change filters. If you’re concerned that the magnets might vibrate around and change position you can use masking tape to hold them down.”

A set of four magnets sells for $30 plus $5 S&H.

Contact: FARM SHOW Followup, TBO Advisor, Box 477, Wilton, CT 06897 (ph 800 707-4826 or 203-834-0330).

From the archive · Full text
Feature story

Two New Tools For Making Deere Tractor Repairs

Featured source:

Mechanic and inventor Bruce Gamble, La Feria, Texas, designed and built a tool to repair the front casting on Deere MFWD tractors.

“It works fast and saves about $1,000 per job,” says Gamble.

The problem is that the front axle pivot pin wears through the bronze bushing and into the casting, thus “egg-shaping” the hole. If you try to put a new bushing in the hole, it won’t hold.

Gamble’s tool makes it possible to drill out the old hole to a larger diameter and then install a new bushing. The best part is you can make the repair right on the tractor.

His tool consists of a 1 1/2-in. dia., 25-in. long boring bar that attaches to a 1/2-in. electric drill, a guide assembly, and a drill press-type feeding mechanism. Gamble removes the front axle and weights and bolts a 16-in. sq., 3/4-in. thick steel plate onto the front of the frame to hold the drill in place. The guide assembly bolts to the plate to keep the boring bar aligned properly. He inserts the boring bar through a hole in the plate and into the worn-out casting and drills it out until it’s round, cranking the handles on the tool as necessary to slowly feed the bar into the casting. Then he drives a steel bushing into the hole to bring it back to its original size and rein-serts the front axle.

“It takes only about two hours to install the tool and bore out the casting,” says Gamble.

“Otherwise, replacing the castings is a 20-hour job which can tie up your tractor for days. You have to remove the tractor’s weights, fuel tank, hydraulic pump, oil reservoirs and, on some tractors, the side frames. The casting weighs about 1,000 lbs. so it’s hard to handle and you can break bolts, hydraulic lines, etc.”

Gamble sells the tool for $2,000 plus S&H. Custom made bushings - depending on the size of the hole you have to drill - sell for $50 apiece plus S&H.

Gamble also makes a specialty tool for repairing the hole in the wheel casting where the tie rod fits on Deere 2955 tractors. The problem is that the outside end of the tie rod works loose causing it to wear on the hole in the axle casting. The tie rod cannot then be tightened up because the hole is wallowed out. The only solution is to replace the axle casting at a cost of about $850 per side plus seals and labor. The tool consists of a 1-in. thick steel plate that bolts onto the casting using the fender mounting holes. The plate has a bushing that fits over the hole and serves as a guide for a drill bit.

Gamble removes the tie rod and bolts the tool in place, then uses a 1/2-in. drill with a 1 1/4-in. bit to drill through the bushing and into the hole. Once it’s drilled out, he presses a tapered bushing into the hole and reinserts the tie rod.

“It takes only about 20 minutes to re-pair the hole on each side of the axle,” he says.

The tool sells for $400 plus S&H. Bushings sell for $30 apiece plus S&H.

Contact: FARM SHOW Followup, Bruce Gamble, Rt. 1, Box 173, La Feria, Texas 78559 (ph 210 797-2169)