Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 20, No. 2 (1996)

Vol. 20, No. 2 (1996)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–32

38 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Otto Wenz, Jr.

Otto Wenz, Jr., Tekamah, Neb.

“If you’re having trouble getting your IH 706, 806, or 1206 tractor into reverse, we can help. We’re Wenz Service Inc. (Rt. 1, Box 70A, Tekamah, Neb. 68061; ph 402 374-2202) and we’ve come up with a kit that solves the problem. We guarantee it’ll last for the life of the tractor.

“The problem with these tractors is that sooner or later bushings on the reverse toggle shaft wear down, making it difficult or impossible to get the tractors into reverse. Our kit consists primarily of a new bushing that’s over three times as long as the original 1-in. IH bushing. It installs on the re-verse toggle shaft.

“If you call us, we’ll send you one of our rebuilt top range covers, which includes the new bushing. Then you simply remove the top range cover on your tractor’s transmission and install ours. (The entire job takes about two hours). Then you send us back your old cover along with a check for the kit.

“We’ve shipped more than 150 kits in the last three years since we started selling them, and more than 99% of our customers have been thoroughly satisfied. The kit sells for $189.”

From the archive · Full text
Reader shop tip

Mark Schlueter

Mark Schlueter, Ryan, Iowa

“Since a lot of double wheel rake manufacturers use a spring-tooth design similar to that of the Gehl 418 I bought in 1992, I’m probably not the only one with this gripe.

“The teeth break off too easily. There are 40 teeth on each of the four wheels, and we’ve already replaced 200 and will have to replace the rest by the end of the upcom-ing season if not sooner. At $2.20 a pop, that adds up pretty fast.

“The problem seems to be that the holes the teeth fit into on the wheel aren’t much bigger than the teeth themselves, which makes for a pretty weak stress point. It cuts the metal and the teeth just shear off. I’ve considered drilling bigger holes for the teeth, reinforcing them with some sort of high tensile plastic or Teflon sleeves, then putting them back on. I haven’t tried it yet but I’d be anxious to hear from anyone who might have or might be able to suggest another solution to the problem. (My address is R.R. 1, Box 52A, Ryan, Iowa 52330).

“Meantime, other than tooth breakage, I couldn’t be more pleased with my Gehl rake. In my opinion, it’s the best rake for corn stalks money can buy.”

From the archive · Full text
Reader shop tip

Eldred Stocks

Eldred Stocks, Jordan, Minn.

“I found an easy way to remove ice buildup along our machine shed sliding door. Just lay a log chain out lengthwise outside the door. When ice and snow build up on top of the chain, all you do is hook a tractor or pickup up to the end of the chain and pull it out. It’ll loosen up all the buildup so you can shovel it away.”

From the archive · Full text
Reader shop tip

Dana Dittbenner

Dana Dittbenner, Seaforth, Minn.

“I use old ironing boards as portable shop benches. I have two in my workshop and I use them all the time. I also have one in my basement for gun cleaning and other small jobs. They are sturdy, portable, store easily in a small space, and usually have a padded surface so that tools and small parts do not roll around or get damaged. You can pick them up at garage sales for a dollar or less.”

From the archive · Full text
Reader shop tip 1 of 4

John M. Kiminski

Individual tip 1 of 4 from this reader’s published contribution.
John M. Kiminski, North Brookfield, Mass.

“I came up with a way to free up ‘king pins’ and some bearings that would not take grease. What I do is take off the quick tach fitting on the hose of my Porta Powr portable hydraulic power unit and fit it with a grease gun end. Then I use it to apply up to 10,000 lbs. of pressure while wiggling the bearing or king pin till hydraulic oil starts pushing through. I then use my regular grease gun, which pushes the oil out so I can get grease through like normal. When I’m done I put the hydraulic power unit back together and add a bit of oil to it. Works great.

From the archive · Full text
Reader shop tip 2 of 4

John M. Kiminski

Individual tip 2 of 4 from this reader’s published contribution.
John M. Kiminski, North Brookfield, Mass.

“Here’s another idea: Several years ago I bought a $25 automotive electric fuel pump and put a length of gas line hose on both outlets. I’ve used it to drain out many a gas tank that needed repair or replacement, or on vehicles being junked. To power the pump, I attached two alligator clips to wires that run from the pump to the vehicle’s battery. A pair of vise grips holds the pump in place.

From the archive · Full text
Reader shop tip 3 of 4

John M. Kiminski

Individual tip 3 of 4 from this reader’s published contribution.
John M. Kiminski, North Brookfield, Mass.

“I made a portable gas tank out of a 1-gal. anti-freeze jug, a length of gas line hose and a metal tire valve stem. I first remove the core from the valve stem (on some stems you have to run a 3/16-in. drill through the stem to make it big enough for gas flow). Then I install the stem in a hole at the bottom of the plastic jug using rubber washers. I run a gas line hose from the valve stem to the vehicle’s fuel pump or just let gas gravity-feed into the carburetor directly. You have to remember to leave the cap loose on the jug so gas will flow.

From the archive · Full text
Reader shop tip 4 of 4

John M. Kiminski

Individual tip 4 of 4 from this reader’s published contribution.
John M. Kiminski, North Brookfield, Mass.

“I also install metal tire valve stems in the top of various liquid containers - like brake fluid - to make it easier to dispense them. You can easily seal them up with a valve stem cap.”

From the archive · Full text
Reader shop tip 1 of 2

Michael Pahls

Individual tip 1 of 2 from this reader’s published contribution.
Michael Pahls, Menifee, Calif

“I’ve found that a 50-50 mix of boiled linseed oil and turpentine works great to loosen seized bolts when working on old or antique equipment. It nourishes wood, protects old metal, and loosens bolts.

From the archive · Full text
Reader shop tip 2 of 2

Michael Pahls

Individual tip 2 of 2 from this reader’s published contribution.
Michael Pahls, Menifee, Calif

“One thing we did in our shop was to paint the floor with a concrete sealing paint. It makes cleanup easy and adds a professional look to our new building.”

From the archive · Full text
Reader shop tip

Charles Sorensen

Charles Sorensen, Corwith, Iowa

“I used galvanized steel pipe, a disk blade, and an old Teflon frying pan to make a portable, telescoping shop light that also doubles as a bolt or tool tray. The light can be adjusted from 4 to 7 ft. high. I welded the bottom of the 1 1/2-in. dia. pipe to the disk blade to make the main stand, then inserted a smaller diameter pipe inside it and mounted a Halogen light at the top of it. I drilled a hole in the side of the 1 1/2-in. dia. pipe and welded a nut onto it, then screwed a bolt that screws against the inside pipe to hold it up.

“I mounted an electric outlet at the bottom of the 1 1/2-in. dia. pipe and use it to power my shop tools. A wire runs from the outlet up inside the pipe to a switch, and from there to the light.

“The pan eliminates the need for a can to throw bolts into. It’s bolted to a steel ring that slides over the 1 1/2-in. dia. pipe. The ring allows me to turn the pan at any angle.”

From the archive · Full text
Reader shop tip

Glen Libbrecht

Glen Libbrecht, West Fargo, N.Dak.

“The original U-joint on my Deere 4850 tractor with mechanical front-wheel drive was wearing down the splined transmission shaft. To prevent further wear, a local welding shop disassembled the U-joint and cut the old yolk off. A slip yoke was welded in to allow for some movement in the driveline. The remaining yoke had two bushings welded on and then was cut so it could be clamped to the drive shaft. Now the small amount of play needed in the driveline is in the slip yoke and not wearing the transmission shaft. The repair cost about $232 but replacing the transmission shaft would have cost a lot more. I’ve used it this way for about three years with no problems.”

From the archive · Full text
Reader shop tip

R. Hiller

R. Hiller, Greeley, Colo.

“Here’s how I start hard-to-start 2 to 8 hp. gas engines. First, I drill a 1/8-in. dia. hole through the air cleaner housing on the engine, making sure the hole is in line with the carburetor intake. Then I make a squirt can using a 1-quart plastic oil bottle that I fit with a metal cap. I weld a small brass tube to the center of the cap - the tube is an ink refill tube from a pen. One good squirt into the engine will get it started. I usually set the plastic can in boiling water before using it to ‘activate’ the gas. You can leave the hole open in the air cleaner as I do, or plug it with a metal screw.”

From the archive · Full text
Reader shop tip

Don Tupper

Don Tupper, Monroe, Wis.

Don used to get false readings when using his long level on stud walls until he made this level holder. The problem was finding a way to get an accurate reading even off a bowed stud. His holder only makes contact at the top and bottom of the wall stud. He made the holder by ripping a 7-in. wide sheet of 3/4-in. plywood. Then he cut out a section along one side that’s 1/4 in. wider than his level. He made 45° cuts on either end to leave a small, flat point to rest on the floor. A hand hold near the center of the holder makes it easy to carry and hold in place. Four strips of duct tape hold the level in place.

From the archive · Full text
Reader shop tip 1 of 2

Richard S. Gerhard

Individual tip 1 of 2 from this reader’s published contribution.
Richard S. Gerhard, Quakertown, Penn.

“To replace the drive belt on our garden tractor, I lift the front end of the tractor up with a front-end loader. That way I can get at it easily without crawling under the garden tractor,” noting that you should block the loader arms up for safety and put blocks under the tractor when it’s in the air.

From the archive · Full text
Reader shop tip 2 of 2

Richard S. Gerhard

Individual tip 2 of 2 from this reader’s published contribution.
Richard S. Gerhard, Quakertown, Penn.

“To replace the starter on a Briggs & Stratton motor, I cut the metal ventilating casing into three pieces. Now I don’t have to remove so many bolts and take the whole casing off to get at the starter.”

From the archive · Full text
Reader shop tip

Corey Hoseth

Corey Hoseth, Mahnomen, Minn.

“A common problem on the farm or around any equipment is failure of lines, hoses, steel wiring, etc., caused by rubbing. I’ve found that wear shields made by Epha Inc. (P.O. Box 1230, 5 Campbell Drive, Hermiston, Ore. 97838 ph 800 867-2351) help solve the problem.”

The company makes two types of wear shields.

“Hose protectors” wrap around the hose or wiring and are held in place by three zip-ties placed in grooves in the protectors (you use a pair of pliers to pull the zip-ties tight). The grooves protect the zip-ties and keep the protector from slipping. A company spokesman says hose protectors are practically indestructible and are effective in temperatures ranging from 40 degrees below zero to 400 degrees above. They can be used on hydraulic hoses, wiring harness, fuel lines, radiator hoses, battery cables, brake systems, air lines, oil lines, etc. They’re formulated to resist solvents, oils, grease, gasoline, etc. Available in 4, 6, and 8-in. lengths. They sell for $2 to $4 depending on the volume ordered (cable ties included).

Hose spacers and hose looms are designed to help keep hoses organized while also preventing hose abrasion at points of contact. Available in 3/4, 1, 1 1/2, and 1 3/ 8-in. sizes, they’re also installed with cable ties.

From the archive · Full text
Reader shop tip

John R. Pauls

John R. Pauls, Inman, Kan.

“My son was putting up a 40 by 64-ft. machine shed with 14-ft. high walls and couldn’t lift the rafters into place with his tractor and loader. Fully extended, the loader on his Massey 1135 reached only 13 ft. So I got $16.35 worth of odds and ends from a salvage yard and rigged a heavy-duty ‘rafter raiser’ that fits in the middle of bucket. I used a 15-ft. length of 4-in. dia. reinforced oil field pipe.

“I made a mounting bracket out of angle and channel iron that welds to the pipe and bolts onto the bucket. The bracket holds the pipe completely rigid on the bucket. For extra strength, I used sucker rod to make a bridge on top of the pipe to reinforce it. The bridge welds to both ends of the pipe after tapering from about 1 1/2 ft. high in the center. I welded a hook onto the far end of the pipe so we could lift up rafter sections with chains. When the device is on the bucket and the bucket’s fully extended, it’ll reach 25 ft. in the air, no problem. It made life a lot easier putting up the machine shed.”

From the archive · Full text
Reader shop tip

Charlie Reich

Charlie Reich, Grants Pass, Ore.

“If you have an old “N” Ford tractor that’s having hydraulic lift problems, here’s how to check it out. Take off the left inspection cover. It’s the one that contains the pto lever. Start the tractor and make sure the pto is turning, indicating the pump is operating. Now lay on your back and look upwards through the opening to observe the lift cylinder and piston. While the pump is running and the lift arms are raised, there should be no oil leakage from around the piston nor should there be any oil coming from around the cylinder itself.

“If there is oil leakage, unbolt and lift off the hydraulic lift cover. That’s the piece the seat bolts to. Upon turning this unit over, you will see the cast iron hydraulic cylinder and piston assembly. There are two minor problems that can occur with the cylinder and assembly: 1. blown gaskets or 2. a leaking piston and worse, a cracked cylinder or a deeply pitted cylinder bore. If the oil was leaking from around the re-taining bolt holes, you probably have some blown gaskets. A complete transmission gasket kit is available for about $12 from Ford.

“Next, you may have to replace the re-lief valve. Grab a big pan or bucket that’ll hold the 5 gal. of transmission oil. After draining the oil, go around to the rear of the tractor and remove the four bolts holding the pto cover and pull out the pto shaft. Now reach down inside the inspection cover opening and unscrew the relief valve. It’s located on the rear of the hydraulic pump just under the (recently removed) pto shaft. If you want to make sure it’s bad, your Ford tractor dealer has a special gauge to test these relief valves. A new relief valve currently costs about $20.

“After installing the new valve, replace the pto shaft and refill with oil. This is a good time to replace the pto shaft seal and install a fresh batch of 90W gear lube.

“This repair will let your old “N” lift and hold like she used to. It’ll be good for another 50 years.” (Reprinted courtesy 9N-2N-8N-NAA Newsletter, P.O. Box 235, Chelsea, Vt. 05038)

From the archive · Full text
Reader shop tip

Edwin Ruff

Edwin Ruff, Moses Lake, Wash.

“To push another vehicle, tie an old tire to the front of your vehicle with a bungy cord. Then you can easily push another vehicle with no hard bumps. On corners or rough spots, you can give extra push and then catch up on the level again.”

From the archive · Full text
Reader shop tip

Eugene Sellers

Eugene Sellers, Trout Run, Penn.

“A lot of farmers have trouble with nuts on studs that refuse to unscrew. I apply ‘Never-Seize’ to any nut that I think I might have to re-move someday. If I think there’s a chance the nut will work loose I use threadlock. It also prevents nuts and bolts from rusting together.”

From the archive · Full text
Reader shop tip

Gary Duspiva

Gary Duspiva, Parma, Idaho

“I use WD-40 as a starting fluid on hard-starting 1-cyl. gas engines used on lawn mowers and other small power equipment. It provides some lubrication to the cylinder and doesn’t fire as hard as conventional starting fluid so it’s easier on the engine.”

From the archive · Full text
Reader shop tip

Harvey Mueller

Harvey Mueller, Neosho, Wis.

“The remote control I built for my Lincoln 275 amp hand-cranked stick welder back in 1950 has saved me a tremendous amount of time because I don’t have to run back and forth to my welder to turn heat up and down. It would probably work just as well on some newer welders.

“It consists of a gear reduction box and a small electric motor that mounts on back of the welder.

“The add-on gear reduction box chain drives the welder’s drive shaft with a # 50 roller chain.

“A 30-ft. length of 3/8 in. dia. cable connects the electric motor with a 1 by 3-in. hand-held control box. To increase heat, I simply toggle the switch on top of the control box forward and toggle it backwards to decrease heat.

“I’ll make plans available if there’s enough interest. I’m at P.O. Box 156, Neosho, Wis. 53059-0156 (ph 414 625-3451).”

From the archive · Full text
Reader shop tip

James Nedrow

James Nedrow, Ashton, Idaho

“Our 1977 White 2-70 diesel tractor has never started easy - we’ve always had to use the electric engine heater every morning year around. In the winter we have to spray ether into the air cleaner in order to get it started. To solve the problem we disconnected the manifold air heater and installed an ether injector from an IH 1466 which didn’t even need it. It works like a charm. However, we have to be sure we don’t push the ether button until the starter is turning the engine and we have to use the ether very lightly.”

From the archive · Full text
Reader shop tip 1 of 2

Paul Donley, Jr.

Individual tip 1 of 2 from this reader’s published contribution.
Paul Donley, Jr., Capron, Ill.

“Old farm bulk milk tanks make great cattle water tanks. They are made from stainless steel so they never rust, have a double wall to help keep water from freezing, and are strong. I have three milk tank waterers on my farm.

From the archive · Full text
Reader shop tip 2 of 2

Paul Donley, Jr.

Individual tip 2 of 2 from this reader’s published contribution.
Paul Donley, Jr., Capron, Ill.

“I mounted a 3-speed car transmission on my feeder wagon so that I can deliver feed slowly into my bunk feeder or fast into fenceline bunks.”

From the archive · Full text
Reader shop tip

Richard Roth

Richard Roth, Scott City, Mo.

“When a bearing went out on the cylinder shaft on my combine all that was left was the inner race. The shaft was too long to use a bearing puller so I used a small air grinder equipped with a 1/32-in. cut-off wheel to cut across the race, allowing it to pop and slide right off.”

From the archive · Full text
Reader shop tip

Dennis E. Heck

Dennis E. Heck, Pendleton, Ind.

“To remove a broken-off bolt I weld a nut onto the top of the bolt so that I can use a wrench to remove it. Heat from the arc-welder will help loosen the bolt if it’s really stuck tight.”

From the archive · Full text
Reader shop tip

Galen Winger

Galen Winger, St. Joseph, Mo.

“When I built my shop I had to grade one side down 3 ft. in order to make it level. I used the extra space to make a pair of steel ramps for servicing my car. First I poured a 4-ft. high concrete wall. Then I welded several short pieces of 10 by 12-in. ‘H’ beam end to end about 20 ft. long and cut them in half to make two ‘T’ beams. I used 4 1/2-in. pipe for posts and set them 4 ft. apart. Then I placed the ‘T’ beams on top of the wall and posts to make the ramps. I later doubled the width of one ramp to accommodate small and mid-sized cars. Works great. I find myself servicing cars more often now because the ramps make cars so much easier to service.”

Shop feature stories

From the archive · Full text
Feature story

“De-Icer” For Older Model Tractors

Featured source:

For years Roger Kuntz had problems in freezing weather with carburetor icing in his old Massey Harris tractor. He solved the problem by making an air pre-heater for the tractor and says the idea would work on other tractors, too.

The idea involved making a heat chamber around the muffler pipe. Outside air enters the chamber through perforations at the bottom, runs up along side the heated exhaust pipe, and then out through a piece of pipe down to the air cleaner and into the carburetor.

Kuntz says the hot air keeps the carburetor free of ice and also helps efficiency of the engine.

“It’s a simple idea that’s easy to make and works well,” he says.

Contact: FARM SHOW Followup, Roger Kuntz, Rt. 1, Box 69, Grainfield, Kan. 67737.

From the archive · Full text
Feature story

“Top Side” Mechanic’s Creeper

Featured source:

“It lets me work from the top side of the engine - anywhere under the hood - with both my hands free,” says Wesley Linn, Mena, Ark., about his “top side” mechanic’s creeper.

The 5-ft. long creeper is made from steel tubing and angle iron. It rolls on four caster wheels. A ladder leads up to a 4-ft. long, height-adjustable platform covered by 1-in. foam rubber and naugahyde. Telescoping legs, held in place by steel pins, allow the platform to be raised up to 6 ft. high.

“I can position it to straddle the front wheels from the side or go over the radiator in front. The caster wheels make it easy to move around. I built it about 12 years ago after an alternator burned out on my 1979 GMC pickup. The alternator was difficult to reach and I watched as a young mechanic tried to reach it. He was kicking, scratching, and clawing and ended up getting poked hard in the side. I decided to build something for him that would make such jobs easier.”

Contact: FARM SHOW Followup, Wesley Linn, 1307 Ransom Road, Mena, Ark. 71953 (ph 501 394-7478).

From the archive · Full text
Feature story

Drill/Tap Guide Makes Engine Work Easier

Featured source:

If you’ve ever had trouble repairing or re-placing an exhaust manifold on Deere 400 and 500 series engines, you’ll like this new drill/tap guide which was introduced at the recent National Farm Machinery Show at Louisville, Ky.

“Often if you have to replace the turbocharger, studs are corroded and break off,” explains inventor Vince Jeffries of Jackson-Lee-Pearson Inc., Flora, Ind.

“This guide allows you to remove the broken stud by hitting it dead center with the drill bit, avoiding damage to the threads on the manifold. You can even do the work without taking the manifold off. It’s a real time and money-saver.”

It consists of a metal plate the size of the base of a turbocharger. It has four 3/8-in. holes, corresponding to stud positions on the exhaust manifold. You simply line up the plate on the manifold, bolt it to two unbroken studs, then insert one of three guide sleeves over the broken stud. You choose the sleeve for the job you’re doing - drilling, retapping, or installing a helicoil.

Comes with replaceable hardened guides for 5/32-in., 5/16-in., and 25/64-in. drill bits.

Sells for $165 apiece for the Deere series engines plus $5 S&H. (Can also be custom-built for most other engines). Indiana residents add 5% tax where applicable.

Contact: FARM SHOW Followup, Jackson-Lee-Pearson Inc., State Rt. 75 South, Flora, Ind., 46929 (ph 219 967-4164; fax 4230).

From the archive · Full text
Feature story

“Gapless Rings” Increase Engine Life

Featured source:

“I learned about gapless piston rings from a driver who competed in the Pikes Peak Hill Climb,” says Harry Wallace, who was so impressed with Total Seal piston rings he became a distributor.

“The design puts two rings in the same groove so end gaps overlap, reducing compression gases leaking into the crankcase,” Wallace says.

Installing the gapless rings on an engine reduces ring leakage to 2% or less, increases manifold vacuum, improves cold starts, extends oil changes, raises compression tests more than a point, and increases fuel mileage and decreases cooling requirements.

The rings are available for almost any engine including farm tractors (antique also), chain saws, snowmobiles, 18-wheelers, and automobiles. They’re available for both gas and diesel engines.

Total Seal rings generally run about 60% more than ordinary piston rings. An information package, including a sample ring, is available for $15.50.

Contact: FARM SHOW Followup, EN-GINE I.Q., Harry Wallace, P.O. Box 521, Woodland Park, Colo. 80866-0521 (ph 719 687-3761).

From the archive · Full text
Feature story

“Whipper Reel” Cord Retriever

Featured source:

If you’re tired of hassling with tangled-up extension cords, you’ll want to take a look at this “Whipper Reel” cord retriever that fastens to walls or ceilings or can be staked to the ground.

It consists of a 13-in. dia. pvc reel and a length of pvc tube that the cord feeds into. One end of the tube attaches to the rim of the reel and the other attaches to a bracket that extends a couple feet out from the reel.

To wind a cord onto the reel, you simply grab onto the tube and use it to turn the reel in a clockwise direction.

“It takes just one hand to operate and has no motors or springs to wear out or break like on other cord retrieval systems. The cord flows in as smooth as silk,” says Sonny Olson, manufacturer.

“The reel holds up to 125 ft. of 14 or 16-ga. cord and up to 100 ft. of 12-ga. cord. You never have to touch the cord while winding it up.“ Sells for $129.50. Olson has also come up with an innovative air hose reel that he says is like nothing else on the market. The Ultra Lite Hosereel (weighs just 10 lbs.) comes pre-spooled with 50 ft. of 3/8-in. dia. air hose.

“It has an ultra smooth exit and retrieve,” notes Olson.

Contact: FARM SHOW Followup, Win Enterprises, 2641 Quail Rd., Chapman, Kansas 67431 (ph 913 922-6513).

From the archive · Full text
Feature story

Revolutionary New Hydraulic Hand Tools

Featured source:

“My hydraulic hand tools are different than any other tools ever developed,” says Bill Gallentine about his revolutionary new hand-operated tools that he says have already drawn a lot of attention from one of the world’s biggest companies.

So far, Gallentine has incorporated his new design into three tools - a large (38-in. long) vise grip-type tool, a small (8-in. long) vise grip, and a 12-in. long cable cutter. The basic design behind the tools could be used in many other tools as well, he notes.

“They work like a hand-cranked bottle jack only a lot faster because they feature a two-stage hydraulic pump instead of a single stage pump,” Gallentine explains.

“There’s a pressurized reservoir inside each tool so they can be used in any position without affecting operation of the ram. A trigger activates jaw return or blade adjustment. They’re entirely modular so repairs, if needed, are easy.”

The tools are capable of exerting tremendous pressure with little hand strain, he notes. Up to 4,000 psi’s for the large vise and up to 2,500 psi’s for the small vise and cable cutter.

Contact: FARM SHOW Followup, Bill Gallentine, 615 Country Club Road, Hood River, Ore. 97031 (ph 503 386-5907).

From the archive · Full text
Feature story

Make Your Own “Roto Rooter”

Featured source:

You can make your own low-cost “roto rooter” out of odds and ends you probably already have on hand, says J.D. Higdon.

Higdon came up with the idea to help a friend clear a 4-in. drainage line.

He first made a cutter head out of a 7 1/ 4-in. circular saw blade. Three pie-shaped pieces were cut out with a torch. Both sides of each of the three prongs were then sharpened on each side.

The three propeller-like blades were next bent forward with a vise-grip as they were heated with an acetylene torch. The hole in the middle of the blade remains centered.

The blade mounts on a 5/8-in., 11 by 3-in. hex-headed bolt. A 1/4-in. dia. hole was drilled about 2 in. deep in the end opposite the threads. Two smaller holes, for set screws, were drilled at 90° through the sides of the bolt.

On the threaded end of the bolt, a 5/8 nut was threaded on and welded in place. The blade then slips on the shaft with teeth facing outwards. A lock washer and another 5/8-in. nut hold the blade in place. A 1/4-in stiff guidewire cable inserts into the head of the bolt and runs to a spool slipped over a 3-in. water pipe. A vise-grip locks the cable to the pipe so he can rotate the spool and pipe together to turn the cutter head.

“We found the obstruction about 60 ft.

into the drain pipe,” says Allison.

“Altogether, it took 80 ft. of cable, including passing through a 90° elbow.” (Back-woods Home Magazine, 1257 Siskiyou Blvd. No. 213, Ashland, Ore. 97520.).