Maurice Tack
“I put Vermeer converging wheels on our Deere 510 round baler. They work well and were cheaper than Deere wheels.”
Read the complete tip →2077 shop tips and stories · page 27 of 35, newest issues first.
“I put Vermeer converging wheels on our Deere 510 round baler. They work well and were cheaper than Deere wheels.”
Read the complete tip →“I’ve had trouble with my pressure water system in that it waterlogs. My plumber inserted a rubber bladder in the pressure tank but it burst and got into the water lines and I had to dig up the…
Read the complete tip →“I used Pyro-Putty to fill a long 3/ 8-in. wide crack in the exhaust manifold on an old 855 Hercules engine. I think the re-pair is now stronger than the rest of the manifold. The putty stays in…
Read the complete tip →“We mounted low-cost duals on our 1992 New Holland 855 baler. It makes heavier, 1,800-lb. bales than the early New Holland 850 we had before so it had more of a tendency to bog down in wet fields.…
Read the complete tip →“I’ve gotten into the habit of using small ratchet cable come-alongs to help hook up heavy 3-pt. equipment. It saves a lot of effort, and is a good safety measure.”
Read the complete tip →“To clean out spray paint can nozzles, just take the nozzle off and squirt WD-40 through it. The squirt tube that comes with WD-40 fits right into a nozzle.”
Read the complete tip →“I spray bright orange paint on chains, binders, etc., to make them easy to spot if they ever fall off equipment.”
Read the complete tip →“We’ve used a Red Ball monitor on our sprayer for several years and it works well. One problem with it is that after a while the monitor tubes tend to get cloudy from sitting in the sun so…
Read the complete tip →“One labor-saving idea we came up with to handle our 62-ft., 8-in. dia. auger was to take the hydraulic leveling motor off our Deere disk and mount it on the auger to raise and lower it. Works great…
Read the complete tip →“I’ve made a support board for using with a lug wrench or breaker bar extension when loosening stubborn lug nuts. It slopes upward along the top edge with a series of slots so you can fit it at…
Read the complete tip →“A 2-liter pop bottle works great to collect oil out of ‘empty’ 1-qt. oil containers. They fit perfect in the top of the pop bottle. You’ll be surprised at how much oil you re-cover.
Read the complete tip →You can get a firm grip on anything from the smallest pipes to the biggest oil filters with this industrial strength clamping tool from New Zealand that’s just being introduced in the U.S.
Read the complete story →“One other thing I do is to use dental tools to get into tight spots to clean. They’re strong and there’s nothing like them for certain jobs.”
Read the complete tip →“Over time, field cultivator shanks tend to straighten out so that sweeps no longer run level. Rather than attempting the difficult task of recurving the shank, I bend the sweep. The method I use is to clamp the…
Read the complete tip →If you have trouble getting sweeps to penetrate hard ground, fiddle with the bolts on top of the sweeps, says Schmitz. He puts washers behind the sweeps, tilting the sweep forward a bit. He’s made the modification on…
Read the complete tip →“Last winter the fan belt broke on my furnace. Not having a spare belt, I looked all over the farm for an extra one from another application. Then I recalled that panty hose or nylons can be used…
Read the complete tip →“I made a gated irrigation pipe puller when I hurt my back in 1980 and still use today. It consists simply of a 32-in. length of 3/8-in. dia. rod with a 4-in. J-shaped hook on one end and…
Read the complete tip →“I re-cently came up with a neat idea for painting wheel rims without getting any paint on the tires. First, I deflate the tires and push the beads in a little. Then I lay a large piece of…
Read the complete tip →“Tired of paying an arm and a leg to buy specially manufactured spark plugs to fit antique farm machinery?
Read the complete tip →“In a recent issue of FARM SHOW, a North Dakota farmer detailed problems he was having with his 1987 Deere 1610 27-ft. single depth control chisel plow. I have had some experience with this problem on similar equipment…
Read the complete tip →“We had problems with U-joint failure on our older Deere 35 forage chopper. After we replaced it with an extra heavy duty joint, we had no more problems.”
Read the complete tip →“We had a problem with our Hesston 500 swather. It was making fairly bunchy wind-rows. We solved the problem by changing the angle of the header and installing ‘strip-pers’ for the auger to run against to knock crop…
Read the complete tip →“Instead of replacing rusted-out silage handling conveyors, we lined them with plastic.
Read the complete tip →“Another modification we made was installing a 6-71 Detroit diesel in our 1350 Minneapolis Moline. The old engine had problems. This fix works well.”
Read the complete tip →“I turned a 15-gal. plastic barrel into a handy holder for redi-rod and flat stock. I cut the top off and then cut out a circle of wood with holes in it to fit the top of the…
Read the complete tip →“Here’s an easy way to make a straight cut on pipe or round stock. Just wrap a square sheet of paper around the pipe and line it up evenly. The edge will be square to the surface of…
Read the complete tip →“We have an old-style Richardson sweep plow equipped with 5 and 5 1/2-ft. sweeps. The U-joint knuckles on the rockshaft often break and new ones are no longer available. To solve the problem we remove the knuckles completely…
Read the complete tip →“My dad had trouble with the glow plug sensor on his 1988 GM Suburban equipped with a 6.2-liter diesel engine. After the dealer changed glow plugs and a sensor with no results I finally found the problem -…
Read the complete tip →“I mounted Deere 77 cotton stripper plant guides on my International 214 cotton picker units in order to make them ‘self cleaning’ in morningglory-infested fields. The Deere guides are much steeper than the IH guides so vines are…
Read the complete tip →“When I was working on a big engine and it came time to put the piston and new ring back in the cylinder hole, I couldn’t find a ring compressor that was big enough. I solved the problem…
Read the complete tip →“I got tired of having to open and close gates all the time on my horse corral so I came up with a simple solution. I left an opening by the gate that’s just wide enough so that…
Read the complete tip →A magnetized nail holding slot at the top of this new hammer makes it easy to start any nail even if only one hand is free. Simply fit the nail into the slot and drive it in.
Read the complete story →“An inexpensive hydraulic press can be made using two 10-in. long, 3-in. wide channel irons and connecting them with two 2-ft.
Read the complete tip →“B’Laster industrial-strength products have saved me a lot of headaches, time, and money for all my maintenance and repairs. The company makes penetrating catalysts, air-tool oil-conditioners, engine life extend-ers, silicone lubricants, citrus and aqueous degreasers, small engine tune-up…
Read the complete tip →“I mounted a 3-speed car transmission on my feeder wagon so that I can run it slow into my bunk feeder or fast for fenceline feeding.”
Read the complete tip →Don used to get false readings when using his long level on stud walls until he made this level holder. The problem was finding a way to get an accurate reading even off a bowed stud. His holder…
Read the complete tip →“I came up with a way to free up ‘king pins’ and some bearings that would not take grease. What I do is take off the quick tach fitting on the hose of my Porta Powr portable hydraulic…
Read the complete tip →“A lot of farmers have trouble with nuts on studs that refuse to unscrew. I apply ‘Never-Seize’ to any nut that I think I might have to re-move someday. If I think there’s a chance the nut will…
Read the complete tip →“I mounted a 3-speed car transmission on my feeder wagon so that I can deliver feed slowly into my bunk feeder or fast into fenceline bunks.”
Read the complete tip →“My hydraulic hand tools are different than any other tools ever developed,” says Bill Gallentine about his revolutionary new hand-operated tools that he says have already drawn a lot of attention from one of the world’s biggest companies.
Read the complete story →“I use a large, old dry chemical-type fire ex-tinguisher filled with gear lube to fill axle housings, etc., in hard-to-reach places. I replaced the pressure gauge at the top of the extinguisher with an air-fill pressure fitting so…
Read the complete tip →“I recently had to put a hole through a 12-in. hollow block for some pipe. Instead of using a chisel, I scribed a circle with a magic marker and nailed masonry nails to the circle at the 12,…
Read the complete tip →“When moving snow with a front-end loader, it’s difficult to keep the bucket from digging into the ground. To prevent the problem, I slit a piece of heavy-walled 2 1/ 2-in. dia. pipe and bolted it onto the…
Read the complete tip →“I use sections of road grader blade to rebuild the points on my subsoiler. I hard surface the sections of blade before installing them on my ripper. These points last as long or longer than store-bought. What’s more…
Read the complete tip →“I’ve found that clear plastic cooking oil bottles make good containers for nails, screws, bolts, etc. They’re tough and you can see what’s in them.
Read the complete tip →“I’ve found that one of the most useful things you can do is keep all pictures and literature on your equipment on file somewhere close-by at hand to keep parts numbers, sizes, and other important information at your…
Read the complete tip →“I was tired of always having funnels burp oil back at me instead of flowing right down so I came up with this idea for a ‘burpless funnel’. It works by simply allowing air to escape while you…
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →Text from the original printed page; see page image.
Read the complete tip →