Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Oscar Scott, Perryton, Texas
Unscrew a hydraulic oil filter, and if you just lose a few gallons of oil, you’re lucky. Oscar Scott wasn’t, so he figured out how to eliminate oil loss and the mess that often comes with it. His…
Read the complete story →From the archive · Full text
Reader shop tip
David Simpler, Elkton, Md.
“After putting four new tires on my skid steer, I had recurring problems with two losing air over time. I finally figured it out. Those little needle/toothpick-like bits on the tread are also on the bead of the…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Stone, Warrenton, Ga.
“We’ve always used bailer twine around the farm, and inevitably, it’ll become a tangled mess which eventually just gets thrown away. Our simple solution is to put the twine in an old 5-gal. oil bucket and run the…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“When picking up many small items, a dustpan works great. Dustpans also work to scoop water off the floor and into a bucket.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“If you don’t finish a project and will be going back to it the next day, set up a table near it and place only the tools you’ll need to finish on it. They’ll be nearby and ready…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“Use a mill cut board instead of a square to mark cuts.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Stephen Zonies, Waitsfield, Vt.
“I’m sure many readers have used just a small amount of caulking, tried to seal the tube, and then discovered it had set. This technique works for me.
Read the complete tip →From the archive · Full text
Reader shop tip
George H. Clark Jr., Seneca, S.C.
“I removed the carburetor on my Stihl MS 291 using a cheap deep-well socket and turned it down to fit the holes.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“Case IH Maxxum tractors have a foam seal under the cab roof that deteriorates and drastically reduces A/C cooling capability. No longer OEM, I used Emseal sealing foam to repair them.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“A 630 Bobcat skid steer hydrostat pump had the input shaft seal retaining snap ring groove destroyed. Rather than buying a new housing or pump, I ground down the housing flush with the mounting flange and had a…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“I’ve added small flat free wheels to each front corner of my 7-ft. Brush Hog. It now doesn’t gouge or cut in like it used to.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
William Sanford, Roxboro, N.C.
“Before removing the power adjust wheels and tires from a 1965 Deere 1010 tractor, I purchased a service manual and read it instead of trying to figure it out on my own.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
William Sanford, Roxboro, N.C.
“My money-saving methods consist of repairing everything I can in my shop and realizing that sometimes I lack the tools or the special expertise to complete a project, so I ask for help.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
William Sanford, Roxboro, N.C.
“I label all parts and hardware so I can locate them. This saves more steps than you can imagine.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Kevin Schrock, Millersburg, Ohio
Bunker Hill Cables of Holmes County, Ohio, sells individual cables directly to customers. These include affordably-priced replacements for name-brand equipment, duplicates of obsolete cables, and custom work for customer-specific applications.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Laurie Ziegler, Maple Plain, Minn.
Farmers, musicians and car enthusiasts are catching on to a product motorcyclists have been using for a couple of decades. BugSlide® was created by a Wisconsin man who rode a motorcycle and was looking for a way to…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Steve Vargo, Valley Grove, W.Va.
At nearly 80, Steve Vargo had no interest in having to jump off his IH 706, so he engineered an emergency stop. He did so after backing it out of his shed and finding himself without steering or…
Read the complete story →From the archive · Full text
Reader shop tip
Dale Witham, Rainier, Ore.
“After drum lines break on my logging Cats and skidder, I replace the line with a new or good, used 5/8-in. line. Usually, the lines are dry and in good shape, with a lot of life left in…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Dr. Karl Spees, Port Angeles, Wash.
“I found a set of new jumper cables at a garage sale at a price too good to pass up. I connected both cables to my work and the other ends to my ground lead clamp. I had…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Steven Janis, Howell, Mich.
“When pulling an engine in the gravel driveway, casters don’t roll, and it’ll sink. Get a couple of 1/2-in. sheets of OSB and lay them end to end under the vehicle. Put the picker on them when you…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
Steven Janis, Howell, Mich.
“If you don’t have the skills to rebuild an engine, seek a local builder for classes to help you (for a fee). Learned skills, problems solved, and pride in yourself. I trained my son for backup skills. It…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
Steven Janis, Howell, Mich.
“I bought a gantry crane from Harbor Freight to help with body/chassis swaps. You just can’t use farm jacks and cement blocks all your life.
Read the complete tip →From the archive · Full text
Reader shop tip
Travis Weber, Ontario
“It seems the plastic tube on the metal wire handles on pails disintegrates quickly with daily use. After dealing with sore finger joints, I discovered a 3 1/2-in. piece of 3/8 or 1/2-in. braided water hose makes a…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Allen Pederson, Nashua, Iowa
“Always carry a needle or stick pin in the lining of your billfold. Use it for slivers, to clean screens, etc.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Allen Pederson, Nashua, Iowa
“Put bright paint or tape around dipstick holders. It’ll help make them quicker to find in the engine compartment.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Jim Stone, Warrenton, Ga.
“We’ve always used bailer twine around the farm, and inevitably, it’ll become a tangled mess which eventually just gets thrown away. Our simple solution is to put the twine in an old 5-gal. oil bucket and run the…
Read the complete tip →From the archive · Full text
Reader shop tip
John Kiminski, North Brookfield, Mass.
“If you have an air compressor that’s hard to start in cold weather, tee in a ball valve at the outlet pump pipe. Open it when it first starts for about 20 to 30 seconds, then close it…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Keith Streeter, Warren, Vt.
“I cut some 2 by 8s, spaced 2 to 3 ft. apart, so I can stack sap buckets horizontally without them sticking together.”
Read the complete tip →From the archive · Full text
Reader shop tip
Max McCaw, Coal Valley, Ill.
“To rewind my string trimmer, I pull off what string I need for both sides. Insert and wind both at the same time. After winding, I cut the loop and install it. It’s a lot easier than winding…
Read the complete tip →From the archive · Full text
Reader shop tip
Pat Bryson, Canaan, N.H.
“Take the fuel filter out of the bottom of the fuel tank and put it in a place you can easily access.”
Read the complete tip →From the archive · Full text
Reader shop tip
Paul Tylutki
“All too often, we try to get the necessary balance when lifting awkward objects. I generally use a 2-in. ratchet tie-down as a leveler. It works wonderfully when trying to align.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“A 630 Bobcat skid steer hydrostat pump had the input shaft seal retaining snap ring groove destroyed. Rather than buying a new housing or pump, I ground down the housing flush with the mounting flange and had a…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“I’ve added small flat free wheels to each front corner of my 7-ft. Brush Hog. It now doesn’t gouge or cut in like it used to.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
William Nadeau, Warren, Maine
“My induction heater works well on rusted nuts and bolts without a flamer.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
William Nadeau, Warren, Maine
“I’ve used my heavy-duty nut splitter on up to 3/4-in. nuts. It only takes a minute and saves the bolt.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Wayne Hopper and Bill Garniss, Brussels, Ontario, Canada
In April 2023, Brussels, Ontario, farmer Wayne Hopper bought a used Deere 8650 4-WD tractor from a farmer near Aylmer, Ontario, thinking he’d gotten a good deal. However, as he drove it to a dealer in Walton, Ontario,…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Shawn Peterson, Woonsocket, S.D.
As a farmer, Shawn Peterson was frustrated with how long it took him to clean farm equipment air filters every day before heading to the field to harvest corn and soybeans. So, 14 years ago, he built his…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Greg Boyd, Berkley, Mass.
“My air supply tank has a Schrader (or bicycle tire) fitting, and it was constantly jamming or taking forever to fill the portable tank. I remembered an article from FARM SHOW where somebody had a quicker way to…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Seaton, Delavan, Ill.
“When starting 1-cyl. engines by keeping the valves from sticking open, make sure the piston is all the way at top dead center.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Lenus Yeo, Clinton, Ontario
“I had to replace bearings on the header drive shaft on my swather. The bolts holding the flangette went through one side of a partition. The other side was only accessible by crawling under the swather to the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 5
Individual tip 1 of 5 from this reader’s published contribution.
Doug Comden, Brethren, Mich.
“I’ve found 150:1 or 200:1 2-stroke oil mix in 4-stroke small engines helps with the ethanol issue.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 5
Individual tip 2 of 5 from this reader’s published contribution.
Doug Comden, Brethren, Mich.
“Don’t keep sharp machine tools (mills, taps, etc.) in piles in drawers. Keep them in original containers or split pieces of rubber hose.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 5
Individual tip 3 of 5 from this reader’s published contribution.
Doug Comden, Brethren, Mich.
“Always use cutting oil or coolant systems.
Read the complete tip →From the archive · Full text
Reader shop tip 5 of 5
Individual tip 5 of 5 from this reader’s published contribution.
Doug Comden, Brethren, Mich.
“I always use Tap Magic for tapping and die work.”
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Meeks, Verona, Va.
“Do you have a bathroom sink light with a pull chain that keeps wearing out? Replace the switch with a toggle switch—they’re very durable.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“This may seem strange, but it works. When working with a spring-loaded drive belt that keeps falling off its pulleys, use a strip of rubber and a boot lace to hang the belt under tension while removing/installing the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“When reassembling something that uses screws, pinning one corner helps hold parts in line until I get a few screws back in. This is a reused concrete form from a septic tank lid.
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Norris, Hollister, Calif.
“Safety is no accident. Before starting any task, take a few moments to lay out a plan. Then, before starting, ask yourself, ‘What can go wrong?’ Just a few moments can save injuries and maybe your life.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Norm Sieting, Rapid City, Mich.
“Another frustration was with the splitter stroke. The wedge always stopped about 2 in. short of the back plate. Any stringy wood hung together, requiring me to pull it apart or run it through again, but reversed.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Richard Labelle, Napierville, Quebec, Canada
Univer-Co developed a clean and handy tool to consistently apply grease where it’s needed most.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Douglas Downing, Swan, Iowa
Longtime FARM SHOW readers may have discovered the Nealey Tire Repair Kit when they were first introduced in 1981 (Vol. 5, No. 1). And it’s likely they still use it today to repair tubeless tires on farm equipment,…
Read the complete story →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Meeks, Verona, Va.
“Do you have a key to the house or shop that’s hard to find on your ring of keys? You can get colored plastic key top covers, but they make the key bulky, and mine wore out quickly.…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“To get something really firm in a bench vise, put it all the way down on the bar or use a spacer block.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“If you need to clean paint or caulk off a screwdriver, put a heavy razor blade in a vise.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“A C-clamp makes a great movable handle for moving plywood.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 4
Individual tip 4 of 4 from this reader’s published contribution.
John Rochester, Charlotte, N.C.
“I use a paint can lid as a low-sided parts/tool tray when working under my car. It’s easy to reach into, slides easily, and is easy to clean.”
Read the complete tip →From the archive · Full text
Reader shop tip
Paul Schmittauer, Albany, Ohio
“I use my leaf blower to clear snow from my sidewalks and garage ramp. If you get to it while it’s still dry and powdery, the blower will clean it down to the bare concrete. I also use…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ralph Volkman, Black Creek, Wis.
“The steel toes in my boots hurt my feet. Before throwing them away, I used a bearing press to bend them outward. It worked—no more sore feet!”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Wyatt Van Damme, Belmont, Manitoba, Canada
Wyatt Van Damme has a simple solution for frozen brakes with The Meth Head canister. Van Damme recalls fighting with frozen brakes while growing up on the family farm. While injecting methyl hydrate into a brake system does…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Doug Peccianti, Sacramento, Calif.
Doug Peccianti of Sacramento, Calif., has a custom urinal in his welding shop that always attracts attention, as it’s made from a Chevrolet Turbo 400.
Read the complete story →