From the archive · Full text
Reader shop tip
Bob Moty, Crystal Lake, Ill.
“I bought several Kangas Flex-Lube grease hose assemblies about 20 years ago after reading about them in FARM SHOW. They were made by Roy Kangas in Dodgeville, Mich., and are among the handiest tools I’ve ever bought. It’s…
Read the complete tip →From the archive · Full text
Reader shop tip
David A. Crooks, Ottawa, Kan.
“I found a way to make diesel engines run better on low sulfur fuel. When refueling, I use a skinny funnel and small tube to mix in 2-cycle outboard motor oil at a ration of 200:1, or 6…
Read the complete tip →From the archive · Full text
Reader shop tip
Fritz Groszkruger, Dumont, Iowa
“Our 2015 VW Golf TDI diesel has a feature that prevents you from making a mistake and putting gas into it. When we started storing diesel in a tank that used to hold gas, I had to find…
Read the complete tip →From the archive · Full text
Reader shop tip
Fritz Groszkruger, Dumont, Iowa
Zip ties can be used for lots of things. Fritz noticed this repair his neighbor made to a broken tarp strap. A tightly closed zip tie was placed over the broken ends and it works like new.
Read the complete tip →From the archive · Full text
Reader shop tip
Henry Yoder, Mt. Vernon, Mo.
“After I use a shovel, spade, digger, hoe or other digging tool, I clean it off thoroughly and then spray it with WD40. You can keep the cost down by buying a gallon of WD40 and using an…
Read the complete tip →From the archive · Full text
Reader shop tip
Joe Johnson, Meridian, Miss.
“I was working on a 3-cyl. Perkins diesel engine from a Massey Ferguson 150. I needed a way to keep debris from falling into the cylinder bores when cleaning the engine block surface for head gasket replacement.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Eugene Yoder, Goshen, Ind.
“My diesel fuel tank is outside, so I wrapped the filter and fuel lines with batt insulation and now my filter doesn’t gel anymore in the winter.
Read the complete tip →From the archive · Full text
Reader shop tip
Kyle Sand, Clearwater, Minn.
“Some of my best, or most user-friendly, funnels for adding engine oil have been the quart or gallon plastic oil containers themselves with the bottoms cut out.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Marvin Anderson, Glyndon, Minn.
“The valve lifters in my Ford Ranger’s engine were getting noisy so I added Schaeffer Moly E.P. engine oil treatment. It solved the problem (www.schaefferoil.com). This additive provides extreme pressure protection for an engine’s bearings, valve train, pistons…
Read the complete tip →From the archive · Full text
Reader shop tip
T. G. Skaggs, Campbellsville, Ky.
“If you have weak shocks that hold up trunk lids or car hoods you can take a piece of pvc slightly larger than the shock. I cut to fit the small end and install over the shock. When…
Read the complete tip →From the archive · Full text
Feature story
By By Dee Goerge, Contributing Editor
Featured source: Dee Goerge
Keeping the sandpaper discs on orbital and other handheld sanders is frustrating when the hook and loop sanding pads start to wear out. Instead of buying a replacement pad, I found a solution in my quilting supplies -…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Jay Boren
LockNLube introduced its grease coupler that locks onto zerks several years ago (Vol. 38, No. 3). Now it has introduced a new grease gun that eliminates the “follower” – the plunger that pushes grease out of the gun.…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S.Dak.
“I bought some heavy-duty reusable zip ties from Menards. I use them to connect box-end wrenches together. Keeps them all together. To use one of the wrenches, just push the button and release the zip tie.
Read the complete tip →From the archive · Full text
Reader shop tip
Gregory Herling, Roseau, Minn.
“When changing oil, I like to add an ounce of clean oil once most of the old oil has drained out. It helps to get all the old oil out. I often use a different weight oil than…
Read the complete tip →From the archive · Full text
Reader shop tip
Kathy Wilcox, Warren, Penn.
“One of the leading causes of house fires is lint in dryers. You should clean out the lint after every use. One of the best ways I’ve found to get all of the lint out is to use…
Read the complete tip →From the archive · Full text
Reader shop tip
Mike Bell, Colstrip, Mont.
“I got a kick out of the report in your last issue from a reader who almost injured himself melting wax onto a stuck bolt. I wanted to point out that the best way to take advantage of…
Read the complete tip →From the archive · Full text
Reader shop tip
Ray Haselby, Marshfield, Wis.
“The Accu-Mix container to mix oil and gas for 2-cycle engines makes it easy to measure ratios in one container. You can mix a little or a lot. The caps have gaskets so they don’t leak even when…
Read the complete tip →From the archive · Full text
Reader shop tip
Cal Miner, Willmar, Minn.
“Older fuel lines are a larger diameter than newer push-lock type hose. To use newer hose on an older engine, the old clamps won’t work. I made my own using an eyebolt. Just cut off the screw part,…
Read the complete tip →From the archive · Full text
Reader shop tip
David Walker, Arlington, Texas
“The muffler screen plugged up on my Echo weed eater and I had trouble cleaning it out. So I used a small drill bit to drill some holes and let the exhaust flow freely again.”
Read the complete tip →From the archive · Full text
Reader shop tip
Glenn A. Haley, Andover, N.H.
“A quick and easy way to thoroughly shake a spray paint can is to attach it to the blade in a reciprocating saw. Just use a couple hose clamps to hold the can on the blade and insert…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Henry Bergfelder, Harrington, Del.
“I always had trouble with female quick couplers leaking. I solved the problem by putting zip ties between the 2 cam locks. Works great.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Henry Bergfelder, Harrington, Del.
“I’ve had trouble with the LockNLube grease coupler that other people seem to like. I found that it wouldn’t stay on the grease fitting and is useless in tight places.”
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Moulder, Cheboygan, Mich.
“One of the leading causes of house fires is lint in dryers. You should clean out the lint after every use. One of the best ways I’ve found to get all the lint out is to use an…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Mason, Beaufort, N.C.
“I use Kiwi shoe polish on my table saw. I live in a very damp environment on the coast. If I put a coat of clear Kiwi on the cast iron saw table, it’s good to go for…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Milan Hochstetler, Cumberland, Va.
“After accidentally breaking the spokes on one of the wheels on my Montgomery Ward 20-in. band saw, I made a new one using 2 pieces of 3/4-in. thick plywood. I used Tite Bond III wood glue (www.titebond.com; ph…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Fred Wieck, Canyon, Texas
“When you need just a drop or two of oil to lube something, just pull the dipstick from whatever engine is close by and use what drips off the end.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Fred Wieck, Canyon, Texas
I’ve used Chapstick to do little lube jobs as well.”
Read the complete tip →From the archive · Full text
Reader shop tip
Fred Yutzy, Vermontville, Mich.
“To keep shovels and other tools clean and rust-free, I fill a 5-gal. bucket with sand and then saturate the sand with diesel fuel and motor oil. After I use a shovel, hoe or other such tool, I…
Read the complete tip →From the archive · Full text
Reader shop tip
Harold Billings, Kenosha, Wis.
“Our 50-year-old bathroom fan was squeaking badly. The bushings are worn out but replacing the fan would be difficult as it is an oddball one with unique mounting brackets. However, it’s easy to take it out for maintenance.…
Read the complete tip →From the archive · Full text
Reader shop tip
Jake Kappelman, Bloomfield, Iowa
“I had a warped fuel bowl mount that leaked fuel, even after I replaced the gasket. Instead of buying a new mount, I took a socket the same dia. as the fuel bowl, wrapped it with sandpaper, and…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Kevin McLain, Albany, Ore.
“I rigged up a little tool to put bleeder valve caps back on. There’s often no room to reach the valves so I attach 1/8 or 1/4-in. fittings to a hand-held vacuum pump which holds the caps until…
Read the complete tip →From the archive · Full text
Reader shop tip
Lyle Smith, Defiance, Ohio
“I use bags of dry ice to help remove stubborn bearings. I wrap a rag around the ice bag and place the bag on the shaft, then wait for about 20 min. The cold ice will shrink the…
Read the complete tip →From the archive · Full text
Reader shop tip
Marvin W. Anderson, Glyndon, Minn.
“If you use ethanol in small engines, plan on replacing the carb inlet needle and seat regularly. To minimize problems, I use carb cleaner instead of starting fluid to start small engines having trouble. The bonus is that…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Wess Cornelius, Winlock, Wash.
“Silicone spray that you would normally use to waterproof leather shoes works great on shovels to keep them clean and sharp. A spray can costs about $3 at a shoe store.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Carl Miner, Willmar, Minn.
“When I need to install or remove a spark plug in a tight place, I slip a short length of rubber fuel line over the plug. Makes it easier to thread the plug in without ruining the threads,…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Carl Miner, Willmar, Minn.
“I use swimming pool noodles to protect my knees when resting them against a ladder rung in order to keep my balance. The noodles can be easily moved from one rung to another.”
Read the complete tip →From the archive · Full text
Reader shop tip
Alfred J. Wolter, Breckenridge, Minn.
“I’ve found that many times when faced with stuck bolts or other parts, if I melt candle wax into them it will help loosen them.”
Read the complete tip →From the archive · Full text
Reader shop tip
Dan Flood, Toledo, Ill.
“A cover board spring broke on my Landoll Tilloll due to dirt buildup. It was constantly swinging back and forth. I solved the problem by bolting chains to the back of the cover board and pulling the chain…
Read the complete tip →From the archive · Full text
Reader shop tip
Dwight Veldhouse, Norcross, Minn.
“I’ve found that writing the oil capacity of a machine on its oil filter with a permanent marker saves time when servicing equipment.”
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Pettis, Plainview, Minn.
“You need a good cutting fluid for drilling and tapping work, and I really like Amsoil compressor fluid. It was recommended to me by a friend. I’ve been an industrial mechanic for about 30 years, and this compressor…
Read the complete tip →From the archive · Full text
Reader shop tip
Kevin Mclain, Albany, Ore.
“I rigged up a little tool to put bleeder valve caps on. With no room to reach some fittings, this simple idea lets me put caps over valves. I also plan on using it to cap grease fittings…
Read the complete tip →From the archive · Full text
Reader shop tip
Len Mallas, Fond du Lac, Wis.
“When I needed to repair the drain pump on our washing machine, I first had to get water out of the tub. I did it by attaching a wet vac to the drain hose on the machine. Worked…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Atlee Miller
Atlee Miller says if you’re looking for parts for pneumatic or mechanical systems, he likely has what you need. With more than 10,000 lines of parts on hand (30,000 in all), he may be right. That’s especially true…
Read the complete story →From the archive · Full text
Reader shop tip
Carl Deaubler, Minford, Ohio
“To reclaim refrigerant from an air conditioning system, I put a 30-lb. tank inside a 5-gal. bucket and pack it in ice. Connect the center hose from a gauge set to the tank. Before opening the valve to…
Read the complete tip →From the archive · Full text
Reader shop tip
Gene Johnson, McDermott, Ohio
“My 2009 Chevy Impala got stuck in park while at a McDonald’s drive-thru when the button on the shifter stopped working. We hit down on top of the shifter to release it, but later figured out that we…
Read the complete tip →From the archive · Full text
Reader shop tip
Jacob Schrock, Trenton, Mo.
“To test pto-powered equipment, I made a bracket to hold a hydraulic motor on the forks of my skid steer. Then I put a 6-tooth spline on the motor’s shaft and hooked it up to auxilliary ports on…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Holt, Cincinnati, Ohio
“The dipstick handle broke on a 2-cyl. Kohler engine and the remainder fell down into the tube. To get it out, I took some clear plastic tubing and connected it to a hand-operated vacuum pump from a brake…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Olen J. Bontrager, Bloomfield, Iowa
“If you have squeaky windshield wipers and it’s not the blades, the problem is likely with the linkage down below. Just a few drops of oil will solve the problem.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Olen J. Bontrager, Bloomfield, Iowa
“A small tire on my garden tiller went flat. I squirted some expensive stuff into the tire but it didn’t last so I coated the bead on the rim with silicone caulk. It has held ever since.”
Read the complete tip →From the archive · Full text
Reader shop tip
Simon Lapp, Ashville, Ohio
“I had a problem with snow blowing into my 23-year-old pole barn under the ventilating ridge cap. I was going to replace the weatherstripping but got to looking at it and decided it would be easier to push…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
David Simpler, Elkton, Md.
“I needed a low-cost way to protect the hydraulic couplers on my skid loader, so I cut up an old heater hose that I already had into 3 to 4-in. lengths that friction fit onto the coupler. I…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
David Simpler, Elkton, Md.
“I wanted a spreader bar that I could use with my skid loader to pick up equipment, so I ordered some chain hooks and used a standard 3-ft. long, Cat. I drawbar to serve as the bar. It’s…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Donald Bunch, Aberdeen, Miss.
“There are times I just need a little ‘swoosh’ of air to blow something off. Not enough to mess with an air compressor. Instead, I keep a little 1-quart pump-up sprayer nearby to use. It works surprisingly well.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Elden Reese, Jonesburg, Mo.
“I use a mixture of used motor oil and transmission fluid on rusted parts or bolts. After applying some, I soak an old sock and put it over the parts to keep them soaked.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Elden Reese, Jonesburg, Mo.
“I bought a tilting car ramp from a car dealer going out of business for $175. I couldn’t build one for that. I set it up outside on a sloping concrete pad so it’s self-cleaning.”
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Swensen, Yankton, S. Dak.
“I learned the hard way that you should never buy the cheap 134a refrigerant that you see on sale all over the place. This stuff is mostly propane, which is why it’s so cheap at $4 to $5.…
Read the complete tip →From the archive · Full text
Reader shop tip
Terry Morgel, Avon, Minn.
“When I buy products in aerosol cans, I write the date on the cans with a permanent marker so I can always tell which cans are older and use those up first.”
Read the complete tip →From the archive · Full text
Reader shop tip
David S. Pepper, Kansas City, Kan.
“A small squirt of starting fluid into the air intake will help start small gas engines that have not been started for a long period of time. The fluid will get you one or two firings which will…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Gary Spohn, Tampa, Kan.
“I mounted a garden hose reel on the top of my portable upright air compressor so I can put 50 ft. of air hose on it. Now I can easily reel and unreel air hose as needed.”
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Swensen, Yankton, S. Dak.
“The little screen in the bottom of a funnel came loose and ended up in the bottom of my fuel tank. Instead of throwing the funnel away, I made a big screen from some window screen and a…
Read the complete tip →