From the archive · Full text
Reader shop tip
Milton Webster, Taylor, Texas
“I’m a small engine mechanic, and over the years have noted that the solenoid shift starters on riding mowers sometimes make a ‘clicking’ noise caused by a hot battery. Many people think the clicking noise means the solenoid…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Red Rock Mfg., Pella, Iowa; ph 641 780-1748; www.redrockmfg.com
Their cast iron drawbar lock is a one-piece device that stops the 3-pt. drawbar from turning on Ford 9N, 8N, and 2N tractors, as well as some smaller Ferguson tractors. No bolts or pins are required for installation.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Cory Miedema
If you have an engine you need to keep running even in the coldest temps and it’s a long way from electric power, Cory Miedema has a solution. Universal Engine Heater Company has been heating off-grid, engine blocks…
Read the complete story →From the archive · Full text
Feature story
Featured source: Steve Beals
“International Harvester built more than 128 letter series Farmall tractor models from 1924 until 1985, and we carry parts for just about every one of them,” says Steve Beals, who runs Farmallparts.com.
Read the complete story →From the archive · Full text
Reader shop tip
Dave Doherty, Lebanon, Ore.
“I made a simple overhead lift by mounting a 4-in. I-beam in my shop fitted with a trolley and an electric hoist from Harber Freight. Very handy for picking up heavy stuff like mowers, ATV’s, and car engines.”
Read the complete tip →From the archive · Full text
Reader shop tip
David Jackson, Peoria, Ill.
“I needed a new floor mat for the cab on my Deere 4230 tractor. My dealer wanted over $300 for one so I went looking for a different solution. I realized that floor mats in car trunks are…
Read the complete tip →From the archive · Full text
Reader shop tip
Michael L. Morrison, Winterset, Iowa
“Sometimes when I have to hook up my 3-pt. mower, it’s tough to get close enough. To avoid hopping up and down off the tractor, I use a come-along to pull the mower up inch by inch. Very…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Paul Krejci, Deerton, Mich.
“When I had to remove damaged bolts from a cramped spot where no extractors would fit, I just welded a wrench to the bolt heads and then removed the bolts. Worked great.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Paul Krejci, Deerton, Mich.
“Another idea I had was mounting a car alternator to a lawn tractor so I can jump start equipment in remote areas of the farm when necessary.”
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Hafner, Chatfield, Minn.
“I had a belt that had been slipping on my riding mower for quite a while. I tried various belt dressings over the years without much luck. I went searching on the internet for a solution and came…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Steiner Tractor Parts, www.steinertractor.com; ph8002343280 (as printed)
You can update your Farmall tractor’s worn governor rockshaft bearings, seals, and bushings with Steiner’s new governor rockshaft repair kit. It’s designed to fit IH/Farmall A, B, C, Supers, 100, 130, 200, and 230 models. The 11-piece kit…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Andrew Sewell
“I made what I think might be the world’s first 3-handed sandblast cabinet,” says Andy Sewell, North Yorkshire, England.
Read the complete story →From the archive · Full text
Feature story
Featured source: Reid Allaway
“I converted our 1978 Hefty-G cultivating tractor from a gas engine to electric motor drive,” says Reid Allaway of Tourne-sol Farm in Quebec.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Richard Batstone
When Richard Batstone bought a 1953 Farmall Cub in the early 1980’s, he didn’t realize it marked the beginning of a new career for him. He spent 3 years restoring the well-used tractor.
Read the complete story →From the archive · Full text
Reader shop tip
Harold W. Allen, Taswell, Ind.
“The 113-in. drive belt on my 60-in. Deere lawn mower deck stretched to the point that it was slipping. Rather than replace it, I installed a shorter tension spring on it and got 2 more years of use…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Matthew B. Tollett, Asherton, Texas
“A lot of lawn mowers are hard to start. An older and wiser cousin of mine suggested sanding down the flywheel, cleaning the coil, and resetting the coil a bit wider. Presto! It worked!
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Richard Liberda, Mandan, N. Dak.
“The distributor on my Ford 8N tractor is hard to get at so my son Mike put a regular coil and condensor on the side of the block. He went right through the dead coil. Now, if the…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Lankford, South Rockwood, Mich.
“Some farm equipment batteries are exposed to the elements, like on my IH 706 tractor. I cover them with rubber using an old tire tube to keep off dust, grease, and sunlight.”
Read the complete tip →From the archive · Full text
Reader shop tip
“I sell a conversion kit that uses gear reduction starters to convert the 2-cyl. diesel engines on Deere tractors to electric start. It’s designed for Deere 70, 720, 730, 80, 820, and 830 models. Switching to a 12-volt…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Vernon Hershberger
The older the baler, the more likely its owner will end up calling Vernon Hershberger for parts and repair, or at least advice. Fixing balers is a big part of Hershberger’s farm equipment repair business. If a customer…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Scott Urschel
Scott Urschel is a bonafide expert in the repair, restoration and general maintenance of Cub Cadet lawn and garden tractors. Urschel’s Cub Cadet Connection business carries a large supply of new, used and reproduction parts for virtually every…
Read the complete story →From the archive · Full text
Reader shop tip
Dave Meiners, Edgerton, Minn.
“When the factory spring broke on my garden tractor’s shift lever, the lever wouldn’t stay in place. I came up with a quick fix by attaching a door spring to the housing in a way that keeps the…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Keith Fisher, New Palestine, Ind.
“After sharpening mower blades, I put vinyl tape on the sharp edges until I’m ready to put them back on the mower. It prevents a lot of small cuts.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bruce Noel, Leslie, Mich.
“A large roller bearing failed on my combine. It would have been unsafe to use a torch to remove it. Instead, I used a Dremel tool to cut it off. That fixed the problem.
Read the complete tip →From the archive · Full text
Reader shop tip
Nick Wiederhold, Williamsburg, Ohio
“The engine on my Swisher Trail Mower kept dying while I was mowing. I thought the problem might be that I was going up and down hills with a gravity-flow fuel system, so I made a bracket that’s…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Galen Snoeberger
Galen Snoeberger can clean up the hydraulic valve mess often found on older Deere tractors. His kit costs about $100 less than Deere’s fix and takes less than 5 min. to install.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Scott Madson
When you need a tractor part, it’s nice to know that the salesman has hands-on experience with tractors and tractor repair. That’s the kind of help Madson’s Service Inc., in St. Nazianz, Wis., prides itself in offering. What…
Read the complete story →From the archive · Full text
Feature story
Featured source: Ron Heidebrink
Retired engineer and pilot Ron Heidebrink has invented a double alternator for use on farm tractors, combines and other vehicles such as trucks, construction equipment and even military vehicles.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Eric Porch
If you have a wiring harness that’s burned or otherwise damaged, Porch Electric can rebuild or replicate it. The company specializes in not just harnesses, but also in everything electric for tractors – mostly of the IH variety,…
Read the complete story →From the archive · Full text
Reader shop tip
Doug Clark, Ilderton, Ontario
“A reader in your last issue said his Kubota L3130 diesel would not start on a real cold day if it had already been warmed up and then shut off – unless he leaves it long enough for…
Read the complete tip →From the archive · Full text
Reader shop tip
John Grady, Northern Ohio Truck Center, Inc., Norwalk, Ohio ph 419 668-4826 or cell ph 419 577-1408
He offers 12-volt gear reduction starters for Deere 70, 720, and 730 diesel 2-cyl. tractors as well as Deere 80, 820, and 830 models. Prices start at $995 to replace a pony start motor. A 12-volt starter for…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Stephen Zonies, Fayston, Vt.
“The gear-box on my bushhog mower started leaking gear oil. It would have been an expensive repair if I had tried to fix it. Instead, I just filled the gearbox with high-quality grease. That solved the problem.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Ethan Rice
Ethan Rice, Spring Hill, Kansas, converted a Harbor Freight floor shop crane to a 3-pt. mounted crane.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Dennis Carpenter Ford Products, ph8004769653; www.dennis-carpenter.com (as printed)
After years of producing “as original” reproduction parts for N-series Ford tractors, the company recently introduced a line of reproduction hood kits for the Ford Jubilee, NAA, 600-800 series, 601-801 series, 2000 and 4000 tractors as well as…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gene Johnson, McDermott, Ohio
“Several years ago I switched my 1954 Ford NAA tractor over to electronic ignition. I had been changing points a couple times a year. The new electronic module was only about $70 and took just a half hour…
Read the complete tip →From the archive · Full text
Reader shop tip
Gerald Ripps, San Antonio, Texas
“On older Ford tractors there’s a plastic knob on a valve located under the fuel sediment bowl that eventually wears out. To solve the problem, I bought a 1/4-in. female thread, full port valve at Harbor Freight and…
Read the complete tip →From the archive · Full text
Reader shop tip
Paul L. Stine, Renick, W.Va.
“My 2009 L3130 Kubota tractor starts fine when it’s cold but if I shut it off after it’s warmed up, it won’t restart. It only happens on the coldest days of the year and it won’t start again…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Jay Russell
Abilene Machine has a fast start option for traditionally hard-to-start 30 series Deere diesels and many other models. Abilene’s planetary gear reduction starter has more torque and turns the engine over at a higher rate, so it starts…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Ed Guenther
“I was born and raised on a farm, and spent a lot of time fixing old tractors and working on cars as a teenager. I gravitated toward fuel injection repair about 20 years ago, opened this shop in…
Read the complete story →From the archive · Full text
Feature story
Featured source: Mark Rinke
“My 855 Deere is a really nice mower tractor and easy to drive, but I made it safer and more ergonomically correct with a few simple improvements,” says Minnesota handyman Mark Rinke. He replaced the original seat, extended…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Gene Wedde
Gene Wedde’s salvage yard is relatively small but he gives his customers big-time service. At a time when many salvage yards put most of their resources into big and late model equipment, Wedde and Sons Vintage Iron focuses…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bob Nelson, Kamiah, Idaho
“My 2014 Deere 50-75 tractor doesn’t like 15-40-weight oil in winter. It starts hard, the oil light comes on, and it won’t heat up to working temperature. I switched to 10-30 oil, which the factory okays. Problem solved.
Read the complete tip →From the archive · Full text
Reader shop tip
Dennis Helmus, White Cloud, Mich.
“Hydraulic lines and filters were exposed underneath my 2012 Kubota L3650 HST tractor. To keep lines from getting damaged, I installed a skid plate, boxing in the hydraulic lines.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Douglas Creswell, Mount Airy, Md.
“One handy thing I did in my barn was to bolt a 4 by 4 to the concrete floor that I can shove against when mounting a front loader bucket on my Ford 1310 tractor. Very handy.
Read the complete tip →From the archive · Full text
Reader shop tip
Fritz Groszkruger, Dumont, Iowa
“I’ve got a ‘global attachment’ quick-tach Deere front-end loader. To release attachments, you pull out the handle and turn. The problem I had was that if I hit a bump while the pins were out, it would snap…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Allan Isaac
“I needed a little belt grinder for touching up ends of threaded rod, so I made one from an old cordless 4 1/2-in grinder,” says Allan Isaac. He made a machined flat pulley on his lathe to screw…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
John Didde, Greenstore, Overland Park, Kansas (ph 913 832-5001; www. Greenstore.org)
“Our Rear Wheel Puller is designed to fit John Deere A, B, G and H tractors. The kit comes with a 1-in. thick round puller plate with elongated holes in it and 4 threaded bolts. You put the…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Gary Swensen
Gary Swensen saw an old Farmall M snap in two when the loader was overloaded. Equipped with a Dual 345 loader and grapple, the M with its wide front end couldn’t handle the 7-ft. bucket loaded with dirt.
Read the complete story →From the archive · Full text
Feature story
Featured source: The Tractor Doctor
FARM SHOW readers often use our stories as inspiration for ideas of their own, and that’s exactly what happened when a story about a simple way to add electric power steering to a Farmall B was read by…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dave Hoover
Dave Hoover knows discbine mower conditioners and has the parts to prove it. With more than 200 parts in stock, the discbine expert ships parts to discbine owners across the U. S. and Canada.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Phil Heisey
If you’re restoring a Cockshutt or Co-op tractor and need parts, chances are very good that Pennsylvania collector Phil Heisey has exactly what you’re looking for. Heisey and his wife, Noreen, have more than 1,000 parts on hand,…
Read the complete story →From the archive · Full text
Reader shop tip
Dave Meiners, Edgerton, Minn.
“I had a hard time using a box end-open end wrench in order to break the stud bolts loose on my tractor’s front wheels. To gain more leverage, I hooked the box end of a second, slightly larger…
Read the complete tip →From the archive · Full text
Reader shop tip
Fred Welton, Grove City, Penn.
“Teeth for a Pequa hay tedder are about $9 apiece at my dealer. With a few minor adjustments, the $1.99 rake teeth sold at Tractor Supply stores make a good replacement. The savings add up if you have…
Read the complete tip →From the archive · Full text
Reader shop tip
Jeff Grube, Wisconsin Rapids, Wis.
“One unique repair I made recently was on my Deere riding mower. The brass sleeve around the driveshaft to the mower deck blades locked up. Deere wanted $200 for a new sleeve. I took it to my machinist…
Read the complete tip →From the archive · Full text
Reader shop tip
Leete Etheridge, Columbus, Texas
“I enjoyed the story you had about the guy who strapped a fuel tank to the back wheel of a blocked up tractor, then ran the wheel to clean rust out of the tank. Instead of using a…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bob Muller, Delanson, N.Y.
“A lot of people don’t know about Corn Head Grease, otherwise called thixotropic grease.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Glenn Fisher
Glenn Fisher, Homer, Ga., came up with an easy way to sharpen the blades on his 3-pt. mounted bush hog mower equipped with a 5-ft. deck.
Read the complete story →