Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 35, No. 3 (2011)

Vol. 35, No. 3 (2011)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

41 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Ralph Stevens

Ralph Stevens, South Berwick, Maine

“I bumped up the mileage on my big 1994 Buick Roadmaster station wagon from 17 to 25 mpg by making a few simple changes. I installed Pulstar spark plugs (www.pulstar.com) and Granatelli spark plug wires (www.summitracing.com). I also installed a K&N air filter (www.knfilters.com) and a larger diameter exhaust system. Those changes really boosted mileage on this big gas guzzler with a 350 cu. in. engine.”

From the archive · Full text
Reader shop tip 1 of 2

Glenn Allen

Individual tip 1 of 2 from this reader’s published contribution.
Glenn Allen, Mt. Vernon, Ohio

“I had to remove a pulley from a driveshaft to replace a bearing on a driveshaft of a manure spreader. There was nothing to pull on so I welded a short piece of keystock to the hub for the puller to grab onto.

From the archive · Full text
Reader shop tip 2 of 2

Glenn Allen

Individual tip 2 of 2 from this reader’s published contribution.
Glenn Allen, Mt. Vernon, Ohio

“When I had to take the transmission out of my Versatile tractor, the dealer said we would have to pull it up and out the door of the cab. Instead, I dug a hole in the barnyard and parked the tractor over it to drop the transmission down. Took only about 10 min. once the shafts and lines were disconnected.”

From the archive · Full text
Reader shop tip 1 of 2

Harold Hart

Individual tip 1 of 2 from this reader’s published contribution.
Harold Hart, Hale, Mo.

“If you get a small tear or rust hole in a gas tank, there’s no need to drain the tank right away. Just rub a bar of soap over the leak and it’ll seal it up temporarily.

From the archive · Full text
Reader shop tip 2 of 2

Harold Hart

Individual tip 2 of 2 from this reader’s published contribution.
Harold Hart, Hale, Mo.

“To anchor bolts in concrete, drill a hole larger than the bolt you’re using and pour sulphur heated to liquid form in around the bolt.”

From the archive · Full text
Reader shop tip

Stephan Rodamaker

Stephan Rodamaker, Janesville, Iowa

“On my 2005 Deere 2210 tractor, there’s no access to the U-joints from the engine to the hydrostatic drive unit. So I cut a tidy hole in the floor at the rear with a grinder. Use a needle nose grease head for the joints. The yoke didn’t have a zerk so I spray motorcycle lube onto it. I use Amsoil spray which doesn’t fling off.”

From the archive · Full text
Reader shop tip

Doug McAlexander

Doug McAlexander, Cedar Grove, Tenn.

“To remove stuck wheels from the rear of a riding mower, I drilled two holes in the wheel an equal distance apart. Then I removed the wheel with an engine balancer puller.”

From the archive · Full text
Reader shop tip 1 of 3

Ralph Blackford

Individual tip 1 of 3 from this reader’s published contribution.
Ralph Blackford, Oak View, Calif.

“I mounted a vise on an old truck brake drum. Makes moving the vise easy and it’s heavy so you don’t have to bolt it down.

From the archive · Full text
Reader shop tip 2 of 3

Ralph Blackford

Individual tip 2 of 3 from this reader’s published contribution.
Ralph Blackford, Oak View, Calif.

“To carry my outboard motor around for maintenance, I modified a 2-wheel dolly to hold it. After working on the motor, I can simply wheel it back down to the boat.

From the archive · Full text
Reader shop tip 3 of 3

Ralph Blackford

Individual tip 3 of 3 from this reader’s published contribution.
Ralph Blackford, Oak View, Calif.

“A friend gave me a 36-in. dia. storm drain street cover. I made a welding and cutting table out of it by adding 3 legs. Works great.”

From the archive · Full text
Reader shop tip

Ronald E. Friedrich

Ronald E. Friedrich, Kenyon, Minn.

“I have an older trouble light with a metal cage. When the regular bulb blew out recently I decided to try a new CFL bulb. It gives out good light and, best of all, the metal shield stays cool. No more burnt arms.”

From the archive · Full text
Reader shop tip

John W. Collins

John W. Collins, Sherburne, N.Y.

“I had to rebuild the bucket on my T-340 crawler when the welded frame broke apart. I bought some 3/8-in. thick plate steel and drilled 1/2-in. dia. pilot holes in it with my small drill press and then proceeded to use the tailstock hand screw on my lathe to drill the holes out to a larger size. It took just a few minutes to open up all the holes. Lots of power and I didn’t have to track down a larger drill press.”

From the archive · Full text
Reader shop tip

Bert Bitter

Bert Bitter, Black Earth, Wis.

“Many of us have gas-powered weed whips that only run a short time. About 90 percent of time it’s an easy fix. The manufacturers run the gas line through the side of the plastic gas tank by drilling a hole smaller than the outer diameter of the gas line. The gas line slowly gets pinched and chokes off the flow of gas to the carb.

“The solution to the problem is to pull the gas line out and drill a hole in the tank at least one drill size larger. Then soak the gas line in boiling water for a few minutes to relax the pinched section. Reassemble and all should be well. I bought a pallet of 37 returned Sears weed whips and was able to repair 30 of them with this trick.”

From the archive · Full text
Reader shop tip

Truett Bell

Truett Bell, Pattison, Texas

“Two years ago I bought a set of Bad Dog Tools drill bits after seeing them demonstrated at a wood working show. The first one I used broke after just a revolution or two. I checked the other 14 bits and only two of them had straight shanks. The rest were so out of alignment that they were useless. I got no response from the company when I contacted them.”

From the archive · Full text
Reader shop tip

Richard Faber

Richard Faber, Tiffin, Ohio

“To anyone interested in how to charge small 12-volt lead acid batteries when you only have a larger 12-volt, 10-amp charger, here’s what you do. Hook a 12-volt light bulb – such as a no. 1157 taillight bulb – in series with the charger and you’ll have a 2.1 amp charger. As the battery takes a charge, the bulb will go dim and dimmer as it is being charged so there’s no worry of overcharging if left on too long.”

From the archive · Full text
Reader shop tip

Jerry Smith

Jerry Smith, Ionia County, Mich.

“Like many of your subscribers in rural areas, I have suffered through a power outage or two. A few years ago, several of my appliances were damaged by a voltage surge. Trying to fix them myself, I learned about a common electronic component called an M.O.V. (metal oxide varister). These are usually a small blue or green disk with two wires soldered to the circuit board. They are in practically every modern appliance for surge protection. They are usually soldered in near the power supply of a circuit board just after the fuse and connect from line voltage to the ground. At line voltage no electricity goes through the M.O.V. but at higher voltage, almost all the electricity goes through to ground and blows a fuse on the circuit board. Often you can visually spot a blackened crack in the M.O.V. The M.O.V. isn’t necessary for the component to work, so if you find a damaged M.O.V., cut it out. Then replace any blown fuses and try to turn the appliance on. If it works, the M.O.V. was the problem. Then go to your local electronics supply store and buy a new one to solder in to replace the old one. I have replaced several at about $2 each.”

From the archive · Full text
Reader shop tip

Larry Goodman

Larry Goodman, Ionia, Mich.

“The company I work for was going to dispose of a steam cleaner that had been sitting around for years because the pump was worn out. However, the water coil and burner were in good shape. I plumbed in a 4-ft. hydraulic hose from the tank from the heater to the washer. Now I have 3,000 psi of hot water (approximately 150°) all for a few dollars. Works great to clean grease off equipment.”

From the archive · Full text
Reader shop tip 1 of 3

Steven Troyer

Individual tip 1 of 3 from this reader’s published contribution.
Steven Troyer, Millersburg, Ohio

“My grandpa converted a freon tank into this portable air tank. He attached a quick coupler that’s used to fill the tank with air. Then he screwed two male coupler ends together to fill it from a supply air hose. Works great for airing up low tires in the field or operating small air tools.

When converting you have to be certain to eliminate all gas inside the tank. You shouldn’t put over 125 psi in a converted tank like this.

From the archive · Full text
Reader shop tip 2 of 3

Steven Troyer

Individual tip 2 of 3 from this reader’s published contribution.
Steven Troyer, Millersburg, Ohio

“Grandpa also made this sanding attachment for his 1/4-in. air drill that works great for polishing the inside of any hole. He made it out of a 3-in. long, 1/2-in. dia. cold-rolled round steel bar, with the end turned down to 1/4 in. to fit into the drill chuck. The bar has a saw cut endwise deep enough that I can fit a strip of 1-in. dia. coated sandpaper in it. The strip of sandpaper wraps itself around the steel rod. Centrifugal force pushes the sandpaper out - it actually does a nicer job than I can with a file. The sandpaper is the kind often used on lathes and comes in up to 100-ft. rolls.

From the archive · Full text
Reader shop tip 3 of 3

Steven Troyer

Individual tip 3 of 3 from this reader’s published contribution.
Steven Troyer, Millersburg, Ohio

“I use several different bottom dies with our hydraulic press. The one shown in the photo is made from 1 3/4-in. dia., 6-in. long rounds set 4 in. apart on a 1/2-in. thick steel plate. My 50-ton press can bend 1/2 by 6-in. bars on it.

“Top dies have to be made according to the configuration of your press. A square bar could be used, up at 45 degrees, if sufficiently supported vertically.”

From the archive · Full text
Reader shop tip 1 of 2

Wes Cornelius

Individual tip 1 of 2 from this reader’s published contribution.
Wes Cornelius, Winlock, Wash.

“I live in a building that’s more than 100 years old, with a metal roof that was nailed on in the 1960’s. Over the years a few leaks have developed. I tried re-screwing the roof and seam-sealing those areas, but it wouldn’t last for very long. Finally one cold, wet, blustery day I went into the attic with an aerosol can of insulation spray foam. I used a flashlight to locate each leak and then sprayed a little foam on the nail or into the seam. The foam bubbled up to create a nice seal. Problem solved.

From the archive · Full text
Reader shop tip 2 of 2

Wes Cornelius

Individual tip 2 of 2 from this reader’s published contribution.
Wes Cornelius, Winlock, Wash.

“To clean household appliances I apply a coat of car wax to all sheet metal. The wax keeps appliances looking brand new.”

From the archive · Full text
Reader shop tip

Roger Avram

Roger Avram, Twining, Mich.

“I welded 2 oil filter wrenches together to come up with this dual strap oil filter wrench, which makes removing hard-to-turn oil filters a much easier job. The dual strap applies the load to a greater area which increases the torque, and it won’t crush the filter like a single strap filter might.”

From the archive · Full text
Reader shop tip 1 of 2

Chad Travis

Individual tip 1 of 2 from this reader’s published contribution.
Chad Travis, Drasco, Ark.

“The bird beak design on my hand-forged staple puller works great for removing deeply embedded staples from trees and posts. The tool has good balance and feel, and there’s a piece of strap metal welded on top to hammer on.

From the archive · Full text
Reader shop tip 2 of 2

Chad Travis

Individual tip 2 of 2 from this reader’s published contribution.
Chad Travis, Drasco, Ark.

“The pto control lever on my Deere 5000 series tractor broke off in my hand one day when I was using it, so I decided to replace it with one that I made out of 3/4-in. dia. solid cold-rolled rod. I heated the tubing and made a double bend handle at the top. The handle extends much farther off the operator’s platform than the factory one, so now I don’t have to reach as far to engage or disengage the pto. And, there’s enough room underneath the handle for my chainsaw.”

From the archive · Full text
Reader shop tip 1 of 2

Leonard Hodges

Individual tip 1 of 2 from this reader’s published contribution.
Leonard Hodges, Callaway, Va.

“The starter pulley on Cub Cadet garden tractors can be easily damaged when you try to remove it because it’s made from lightweight metal. A new replacement pulley costs about $35. To solve the problem, I made a puller that prevents the damage. I have a few in stock, and they sell for $50 plus S&H.

From the archive · Full text
Reader shop tip 2 of 2

Leonard Hodges

Individual tip 2 of 2 from this reader’s published contribution.
Leonard Hodges, Callaway, Va.

“I came up with a tool for my Cub Cadet garden tractor that compresses the spring on the tractor’s driveshaft, making it easier to replace the tractor’s throw-out bearing. It’s a safe way to get the job done. Anyone who’s interested can call me and I’ll tell them how to make it.”

From the archive · Full text
Reader shop tip

George Rodman

George Rodman, Ostrander, Ohio

“I’ve had great success starting lawn mowers in the spring, by squirting a shot of gas directly into the carburetor using a hypodermic syringe. I’ve found that small plastic complimentary shampoo bottles offered by motels work well for this, too. Maybe even better because they last longer, as the gas tends to destroy the rubber in a hypodermic syringe.”

Shop feature stories

From the archive · Full text
Feature story

“Tumbler” Dresses Up Metalwork

Featured source: Brian Johnson

When blacksmith Brian Johnson finishes a custom metalworking job, he likes to soften edges and polish the steel. His homemade parts tumbler filled with waste from a metal punch press does just that.

“It gives the pieces I make a nice burnished appearance before I clear coat them,” he says.

“I made some pot and pan hangers out of steel strap and square stock for clients recently. The tumbler took the sharp edges off and added eye appeal.”

The tumbler drum, which rotates at about 42 rpm’s, is fashioned from a 30-lb. propane tank. Johnson cut one end off – after first purging all gas from the tank – and remounted it with hinges and a latch. It rides on steel bearings mounted at the ends of four arms made from square tubing. A fifth bearing mounted to a rear arm rides against the tapered end of the barrel.

“That fifth bearing helps to keep the tumbler from walking as it rotates,” says Johnson.

“I covered the bearings with rubber hose material. I think that along with the drive belt, it helps hold down the noise.”

Power to rotate the tumbler is supplied by a 1/2 hp electric motor. A worm drive gear reducer transfers the power with more than enough torque to the drive belt.

“I picked up a 20-in. pressed steel pulley and cut out a hole roughly the size of the tank,” says Johnson.

“I pounded it in place over the tank and it fit tight. I’ve never had to weld it or secure it in any way.”

A 3/4-in. belt runs from the pulley on the gear reduction pulley and around the tank pulley. Belt tension is maintained automatically.

“I mounted the motor and the gear reduction case on a steel plate and hinged one end of it to the frame,” says Johnson.

“The weight is enough to keep the belt tight.”

The tumbler is a lot lighter than it looks, thanks to the square tubing frame. Johnson says it weighs about 90 lbs. when empty. He estimates he has about $100 in it. Most parts, aside from the previously unused motor, came from an area scrap dealer. That included the perfectly good gear reduction unit that he got for scrap iron price.

Contact: FARM SHOW Followup, Brian Johnson, 16777 County Rd. 75 N.W., Clear-water, Minn. 55320 (ph 320 558-6898).

From the archive · Full text
Feature story

Pickup-Mounted Metal Bender

Featured source: Warren Farley

Warren Farley didn’t have enough room in his small garage for a stationary metal bender, so he built one that fits into the receiver hitch on back of his pickup. The unit consists of a 4-in. sq. vertical steel tube welded to two 12-in. sq. metal plates and uses four 18-in. long arms and a 36-in. long handle at the end to do the bending. A 4-bolt, adjustable clamp on the tube attaches to an adjustable hitch plate on the pickup. He used 3/4-in. thick, 2-in. wide steel to build the arms and drilled 5/8-in. dia. holes through them, which accept grade 5 bolts that hold the arms together.

“I built it after I bought a small stationary metal bender from Harbor Freight. It only cost $80 but couldn’t even bend 2-in. material,” says Farley.

“I ended up spending nearly 4 times that to build my bender, but it’s portable and is built a lot heavier. It’ll bend steel up to 3 in. wide and 3/8 in. thick, or maybe thicker, and with the long handle, it’s very easy to use.

“It weighs about 200 lbs. so I use a small 2-wheeled cart to move it around. It’s all I can do to lift it into the back of my pickup.” Contact: FARM SHOW Followup, Warren Farley, 280 State Street, Jackson, Ohio 45640 ([email protected]).

From the archive · Full text
Feature story

Seed Boot Mounting Repair Kit

Featured source: Craig Craft

Craig Craft recently sent FARM SHOW photos of a kit he developed to solve a common problem with the seed boots on Deere 50, 60, and 90 Series no-till grain drills.

“Deere no-till drills use a pair of cast iron lugs on the main arm to mount the seed boot. The lugs don’t have replaceable bushings. As the center seed boot mounting hole wears, the rear of the seed boot works loose and flexes upward, allowing seed to randomly miss the furrow,” says Craft. His solution to the problem involves drilling out the hole on the seed boot mounting lug, then installing a hardened full length bushing made from heat-treated aircraft grade alloy steel.

“Restoring the tight fit of the boots results in better stands and higher yields,” says Craft.

“The repair can be made with the mounting arms still mounted on the drill. The seed boots themselves require no modification. Only the seed boot and opener blade have to be removed.” The kit he developed includes a 2-piece drilling jig that’s used to drill through the hole, and the hardened bushings. The bushings are driven into the worn-out holes in the mounting lugs using a simple driving tool that Craft designed.

“The new bushings allow the seed boot to pivot as originally designed,” says Craft.

“Thanks to our drilling jig, the holes are true and parallel to the original location. The kit actually lets you restore the seed boot mounting clearances to better than new tolerances. For example, factory new 50 Series drills have less than 3/4 in. total bearing surface for the seed boot mounting bolts, while drills repaired using our method have 2.125 in. of total bearing surface.

“The repair allows you to use OEM parts and hardware. Factory and aftermarket seed boots, mounting bolts, and leaf springs can be installed without modification.” A complete kit for 12-row drills sells for $475 plus S&H; 24-row drills, $595 plus S&H; 32-row drills, $695 plus S&H; 44-row drills, $795 plus S&H. Contact: FARM SHOW Followup, Craig Craft, Craft Air Services, LLC, 865 Swamp Rd., Hertford, N.C. 27944 (ph 252 426-9676; [email protected]; www.jddrillfix.com).

From the archive · Full text
Feature story

Wireless “Ears” Help Pinpoint Noisy Mechanical Problems

Featured source: JS Products

Finding an annoying noise inside or under-neath a vehicle is a whole lot easier with the Wireless ChassisEAR from JS Products. You simply clamp one of the sensors into a suspect area and take a test drive.

JS Products sent FARM SHOW a set of sensors to try out and both the sensor/transmitters and receiver worked as promised.

With units strapped in each wheel well, road noise transmitted clearly to the headset connected to the receiver. Clamped to the water pump, the sound of fluid movement was clear. The 6-way switch lets the operator quickly move from monitoring one transmitter to another. (While four transmitters are standard with the ChassisEAR kit, two more can be added).

Wanting to test it out with a problem vehicle, we gave the diagnostics kit to mechanic and FARM SHOW contributor Jerry McCabe (Vol. 34, No. 5). He tried it out and was pleased with how it worked.

“This would be great for a one-man shop or anyone who works on his own equipment,” suggests McCabe, who runs McCabe Auto Repair in Preston, Minn.

“I can have another mechanic jump in back and slide from side to side to help locate a problem sound, but that takes him away from his job. For $200, this unit makes finding the problem fast and easy.”

The wireless transmitter consists of a small rectangular box with microphone clamps. A magnet on the transmitter box holds it in place temporarily until Velcro straps can secure it.

The microphone clamps are wired to the transmitter. They can be clamped to springs, torque rods, shocks, body mounts, dash assembly, drive train, axle hubs, ring and pinion bearings, oil pump, etc.

Contact: FARM SHOW Followup, JS Products, Inc., 5440 S. Procyon Ave., Las Vegas, Nevada 89118 (ph 702 362-7011; toll free 800 255-7011; [email protected]; www.steelmantools.com).

From the archive · Full text
Feature story

Pto Clutch Kit For 2-Cyl. Deeres

Featured source: Dan Weber

If you have a two-cylinder Deere, you can save money two ways with the WTR Pto Clutch Kit. The kit includes all the disks and separator points needed to replace the entire pto clutch.

“Buy the complete kit, and you can save up to 70 percent compared with buying each piece individually from Deere,” says Dennis Weber, WTR.

“Replacing them all at once saves time and extends the life on all the parts compared to replacing only those with visible damage.”

Weber compares replacing parts piecemeal to replacing only one tire out of four.

“All too often, tractor owners open up a clutch pack and find a few plates where the linings have fallen off,” he says, “They just replace them. A few days or weeks later more fall off, and they have to open up the clutch again to replace those.”

Equally important, he adds, is the increased wear on the replaced parts from having a damaged part undetected and not replaced. This is as true of separator points as the lined plates.

“People look at separator points and think they don’t have to replace them unless they are burned or obviously damaged,” he says.

“But grooves in a separator point can shorten the life of the lining on a new clutch disc.”

Another advantage to replacing old pto clutch packs with new ones is improved quality. Weber explains that the glue used to fix the linings and the material is much superior to earlier versions.

“I don’t think I’ve seen linings come off the newer versions,” he says.

“They are just a lot more durable.”

Clutch kits vary in price from $249 for earlier model two-cylinders to $445 for 820 and 830 Deere tractors.

Contact: FARM SHOW Followup, WTR, 3508 Maddy Anne Ct., Rapid City, S. Dak. 57701 (605 209-9698; [email protected]; www.wtrparts.com).

From the archive · Full text
Feature story

He Turned An Alternator Into A Great Stick Welder

Featured source: Mike Toppen

Mike Toppen turned an old truck alternator and a Sears garden tractor into a portable, high output stick welder. He also uses it to jump-start vehicles and for high amperage charging. He can even use it to run a TIG welder or power his circle saw or other “brush-type” tools.

“A normal automotive alternator can be used for a welder, but is limited to 60 to 70 amps output current,” says Toppen.

“If you’re a welder, you know it’s nice to have a higher output current than this. I used a truck alternator with double-drive belts and from 135 to 185 output amps. This makes for a nice capacity unit.”

The used truck alternator is brushless with a stationary field coil that protrudes into the double V-belt driven field shell. This allows Toppen to put larger amounts of voltage into the field coil without overtaxing brushes. Otherwise, the alternator had the usual regulator, diode trio and bridge rectifier under the plate on the end cap.

“I removed the plate which let me also remove the regulator and the diode trio that I didn’t need as I didn’t want them regulating (limiting) output,” explains Toppen.

“I also removed the bridge rectifier and replaced it with an RD-05 from Regitar. It doesn’t use avalanche diodes, which it’s said don’t last long in a welder.”

With those minor changes, sandblasting and repainting parts, Toppen had his welder. With the help of a friend, he bent steel plate to make a mounting frame for the front of his Sears garden tractor. Its 12 hp Koehler engine had pulleys in place for various Sears add-ons that made it ideal to power the welder.

“I still needed to get the rpm’s up from the tractor engine’s 3,200 to 3,600 maximum rpm’s to the 7,000 to 8,000 I needed for the alternator,” says Toppen.

“I added a jackshaft with a two-stage gear induction.”

To allow for adjusting the belt drive, Top-pen machined a lengthwise slot in the adapter plate. He used pieces of square tubing to raise the welder and to mount it to the plate for easy adjusting.

“I knew I would need 40 to 50 volts and around 80 amps to get a decent arc when welding,” says Toppen.

“My 12 hp engine was more than sufficient in power. The 50 amps times 80 volts equals 4,000 watts, which is equal to 5 hp. We got another 7 hp to work with.”

A pair of low cost jumper cables connects the garden tractor battery to alligator clamps on the field to power up the coil. Welding cables connect to the output posts on the alternator.

The first time Toppen fired up the welder, he selected an all purpose rod and a heavier duty rod. He quickly found he could adjust the engine rpm’s to the welding rod to find its particular output “sweet spot”.

“The great thing is that I can use it on the garden tractor the way I have it, or I can mount it on a full size tractor or even under the hood of a pickup if there’s room for a jackshaft,” says Toppen.

“I’ve done equipment repairs in the field, welding tongues back on wagons and such. It adds real versatility to the shop.”

Toppen offers more in-depth instructions for making the portable welder on a CD that he sells for $15 plus $3 shipping. The CD, along with other Toppen instructional CD’s, is available on Toppen’s eBay store. It includes high quality images, schematics and wiring diagrams. Also included are modifications to use the portable welder as a TIG torch and for running a carbon arc torch. He also explains how the welder can be used to power brush-type motors.

Contact: FARM SHOW Followup, Mike Toppen, P.O. Box 138, Burnips, Mich. 49314 (ph 269 673-5597; [email protected]; http://site.toppentech.com/; http://stores. ebay.com/TOPPENTECH).

From the archive · Full text
Feature story

“Combo” Safety Glasses Also Protect Ears

Featured source: Wedworth Mfg.

You get both eye and ear protection in one with these new “combo” safety glasses that are equipped with built-in earplugs on the frames. The built-in earplugs hook onto ear pieces that are part of the eyeglass frame, so when you remove the glasses the ear plugs come out of your ears. If you want to wear the glasses without the earplugs, simply fold the plugs over so they lay against the eyeglass frame. The combo eyeglasses are available either clear or colored. They sell for $12.99 plus S&H. Foam ear plugs are replacable.

Contact: FARM SHOW Followup, Wadsworth Mfg., 35008 Dublin Gulch Road, St. Ignatius, Mont. 59865 (ph 800 535-2428; [email protected]; www.cattlebanders.com).

From the archive · Full text
Feature story

Sturdy Tractor-Mounted Chain Box

Featured source: Roger Gutschmidt

Roger Gutschmidt’s Deere 7530 MFWD tractor is fitted with a handy storage box he built and mounted to the front end.

“The box is made from 8 by 8-in. sq. tubing with 3/8-in. sidewalls, and it’s 21 in. long, which is the width of my tractor. I made it heavy duty so it won’t get damaged or crushed if I accidentally bump it,” he says.

“I made the box to hold a log chain, hitch pins, and clevis. It’s sturdy and easy to get to, and there really isn’t a place to put a tool box anywhere else. I don’t want this stuff inside the cab on the floor where it could get stepped on or bump the cab glass and break it.” The box has a cover at each end for easy accessibility. The covers pivot on a bolt in one of the lower corners.

“Before mounting the box to my tractor, I painted it to match, and I think it looks real good,” Gutschmidt adds.

Contact: FARM SHOW Followup, Gutschmidt Manufacturing LLC, Roger Gutschmidt, 6651 Hwy. 56, Gackle, N. Dak. 58442 (ph 701 698-2310; [email protected]).

From the archive · Full text
Feature story

How To Lubricate Hard-To-Reach Areas

Featured source: Jeremy Aaron

Jeremy Aaron, an aircraft mechanic from Washington, Penn., was tired of not being able to reach some areas on machines being serviced with the plastic straws that come standard with WD-40 and aerosol products. Getting at remote areas inside engine compartments meant spraying the whole area from a distance, making a mess and wasting chemicals. So, he invented what he calls Extend-A-Lube Super Straws. Super Straws are 16-in. nozzles that are compatible with virtually all aerosol cans that come with standard length straws and can easily be cut to any length you need. Aaron packages his Super Straws along with another product called Hold-Its. These are elastic rings that wrap around the can and hold onto the straw so it won’t get lost. They’re sold through tool distributors. A pack of three Super Straws and three Hold-Its sells for $4 plus $1.25 S&H. Contact: FARM SHOW Followup, Extend-A-Lube, 4009 Outlook Dr., West Mifflin, Penn. 15122 ([email protected]).

From the archive · Full text
Feature story

Simple Ground Heat System Cools, Heats Shop

Featured source: Wess Cornelius

Wess Cornelius’s made-it-myself ground heat system provides heating and cooling for his shop at minimal cost.

“I use it to help heat and cool my 15 by 32-ft. shop,” says the Winlock, Wash., man. A friend used a trencher to bury 100 ft. of 4-in. dia. plastic non-perforated drain pipe 4 ft. deep in the ground. It was buried in a loop around the shop. After installing the pipe in the trench, he attached an elbow to both ends and brought the pipe up at both ends inside the shop. A few inches extend above the floor. A small electric fan at one end of the building is used to suck air through the tube. The fan is placed inside a 5-gal. bucket with a 4-in. dia. hole cut into the bottom.

“It provides free energy and was cheap to put together. I paid $100 for the pipe and $75 to hire the trenching work,” says Cornelius.

“The ambient air temperature 4 ft. deep in the ground is 50 to 54 degrees. It’ll change the air temperature 10 to 20 degrees, so if I go to my shop on a 30 degree day, the temperature inside the shop will be 40 to 50 degrees. During the winter, I usually turn the fan on about 2 hrs. before I go to the shop. If I leave the fan on at night when it’s freezing outside it’ll still keep the shop at 45 degrees or higher. It also helps on hot summer days. I’ve used it several days when the outside temperature was over 90 degrees, yet the shop stayed at about 75 degrees. If I had left the fan on overnight the shop might have cooled even more.” Contact: FARM SHOW Followup, Wess Cornelius, 1312 Ferrier Rd., Winlock, Wash. 98596 (ph 360 785-4178).

From the archive · Full text
Feature story

Tractor Loader Tool Holders

Featured source: Dan Bodda

“I just bought a new L4240 Kubota tractor cab and loader. I used to carry a toolbox in the cab of my last tractor and it was always in the way. So this time I decided to find a better way to hold a few chains, tools and pins,” says Dan Bodas, Pittsburg, Mo.

“The loader has two smaller 4-in. dia. tubes where the loader attaches to the chassis, and a larger 4 1/4-in. tube in the loader frame itself.

“I bought four 4-in. dia. pvc expander plugs, which make perfect covers in the ends of the tubes. The plugs expand so no adhesive is required to hold them in and you get a watertight storage compartment. The plugs cost just $5.99 each and come in different sizes.

“The 4-in. plugs fit perfectly into the two 4-in. pipes. They were a little loose in the bigger 4 1/4 in. loader tube so I bought a 4-in. pvc connector fitting and cut a slot in one side to allow it to slip inside the loader tube. The expander plugs fit perfect into the pvc inserts.” Contact: FARM SHOW Followup, Dan Bodas, HC 77, Box 1043B, Pittsburg, Mo. 65724 (ph 417-327-6767; [email protected])

From the archive · Full text
Feature story

“Socket Board” Makes Tools Easy To Find

Featured source: Mike Sieve

Mike Sieve is able to organize sockets by drive and size, and organize wrenches by size, thanks to the handy tool organizer he built. The tool organizer’s backboard measures 8 ft. long by 26 in. high and is made from 14-ga. sheet metal set inside a frame made from lengths of 1 1/2-in. angle iron. The various size drive sockets set on rows of pegs that extend through the backboard. There’s a 12-in. deep shelf underneath.

“The backboard is painted black, and the silver sockets and wrenches really look nice against it,” says Sieve.

“I built it because I had been storing my sockets and tools on a cart, but it seemed like I could never find the size that I needed quickly. For me, finding the tools I need is all about speed.” He welded 4 pieces of angle iron together to make the shelf frame, then cut out a piece from the sheet metal to fit inside and tack welded it on. Then he cut out the backboard. The next job was the hardest – laying out the pattern for the holes where the pegs, actually nails – go through.

“I needed to figure out which socket sizes I already had, and which sizes would be available to add in the future. I decided I wanted to have at least 5 rows of sockets plus 1 deep socket for my 1/4, 3/8 and 1/2-in. drives. I keep SAE sockets on the left side of the board and metric on the right. I figured I needed to accommodate socket sizes up to 2 in. or 50 mm.” The bottom half of the board is used to store 1/4 and 3/8-in. drive sockets, which are spaced 1 1/2 in. apart both horizontally and vertically. These sockets extend 6 rows high and go all the way to both ends of the backboard. The top half of the board is used for 1/2 and 3/4-in. drive sockets. The top row is only for 3/4-in. drive sockets, which are spaced 2 1/2 in. apart. Right below it are 6 rows of 1/2-in. sockets, which are spaced 1 3/4 in. apart both horizontally and vertically.

“To get the pegs ready, I drilled out a hole sized for the nails that I wanted to use,” says Sieve.

“I used nails that would be 1/2 in. longer than the socket’s total length. Drilling all those holes was a tedious job. Then I placed all the nails in their holes and welded them to the board from the back side. Contact: FARM SHOW Followup, Mike Sieve, 2345 Ritchance Rd., Alfred, Ont., Canada K0B 1A0 (ph 613 675-2754 or 613 577-2099; [email protected]).