B.R. Mitcham
“My 1954 Farmall Cub had a clicking sound in all gears. After pulling the whole transmission and differential apart, it turned out to be a bushing in the reverse idler gear. I changd the bushing and no more clicking.”
Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39
33 selected entries · Complete text of selected entries
This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.
“My 1954 Farmall Cub had a clicking sound in all gears. After pulling the whole transmission and differential apart, it turned out to be a bushing in the reverse idler gear. I changd the bushing and no more clicking.”
“Like many of us, I use a chain hoist to lift the front of the lawn tractor to get at the blades. The last time I was going to do it, I was walking around the shop looking for the 2 by 4 that I use as a chain spreader to clear the sides of the hood when the clevis I keep on back of the tractor caught my eye. I thought, ‘Why not lift the rear of the tractor instead?’ “The tractor didn’t seem to mind and I got the blades sharpened and replaced with no problems. I think most people lift the front end because it’s lighter but it’s a lot more convenient to lift the back.”
“I made a pry bar from a pickup leaf spring. It’s thin, yet wide and strong. I had to heat it to bend one end. There was no need to sharpen the ends since it already had pretty thin ends but some springs would probably need that. The bar works great for removing wood trim without scarring, and the curved section is useful for lifting sheet rock an inch or so into position. I’m sure there will be many other uses I haven’t thought of yet.”
“If you have a dark corner in your workshop or back room, install a motion sensor light there. It comes on only when you go there and shuts itself off after you leave. Very useful if your hands are full.
“Another handy idea is that when I buy a come-along, I remove the slip hooks and permanently add about 2 ft. of chain with jam hooks to each end. This makes the come-along much more useful. They attach to many more situations without having to use extra chain.”
“We use a chainsaw tip grease gun to lubricate the regreasable bearings on an IH 470 disk after the grease fittings get worn by dirt. This works until the sides of the fitting wear through.
This company sells extraction tools driven by standard 3/8 and 1/4-in. reversible power drills, that make it easy to remove stripped or broken bolts and other threaded fasteners. The “ProGrabit” works on anything from a no. 4 screw to a 3/8-in. bolt.
“Drill-out” is a broken bolt extractor, consisting of a drill-bit and extractor in one tool.
“X-out” is designed to remove damaged screws by simply applying pressure on the fastener head with a reversible power tool. Or, it can be used manually with a ratcheting screwdriver.
“Old golf balls make comfortable file handles. Just drill a suitable size hole in the golf ball and drive it over the tang of the file. The right size hole will make a tight fit that keeps the golf ball on forever.”
“I’d like to know if anyone else has had problems using ethanol fuel in chainsaws. Here in Florida, I find the fuel boils and causes vapor lock as it gets toward the bottom of the tank. My saw manufacturer suggested using Stabil fuel preservative normally used for winter storage. It didn’t help. The saw has to cool down about an hour before I can restart it. Any suggestions?”
“I have an older Hydro-Mac skid loader and had a problem shearing the roll pins in the machine’s hydrostatic pumps. To solve the problem, I mounted stops on the pins’ forward and reverse travel. Now the arms don’t go far enough in to shear the pins before they reach the end of their travel inside the pump.”
“If you have an outside furnace that develops a slow leak, put a couple cans of radiator stop leak in it. It’ll solve the problem if the furnace doesn’t leak a lot.”
“My Kubota 4-WD tractor came equipped with industrial tread tires. Unfortunately there was no clearance for tire chains and I didn’t want to replace the wheels and tires. Instead I installed Tungsten studs in the tires, which greatly increased traction in snow. The studs are available from ATV and snowmobile dealers.”
“I built this roller stand out of angle iron and sq. tubing. I use it with my drill press and table saw when handling long material. Similar commercial roller stands sell for $20 to $30. I got the roller free from my school. It was the wrong size for another roller stand so they didn’t need it any more.”
“On small chains where even a 1/4-in. hook is too large, I take a cut link from a somewhat larger chain that’s still small enough to fit in one of the links. I put the cut link in the vise and close one half onto the chain, leaving the other half to hook into whatever link is necessary to secure something. It also works well to use such a chain in combination with a bungee strap.
“To come up with an inexpensive but effective fire starter for a fireplace or brush pile, I simply tie an old sock in knots as tight as I can and soak it in a little diesel fuel or starting fluid. The sock will burn for several minutes which is enough to start most pieces of wood, even if they’re wet.
“I own a number of cordless tools (five drills, three saws, a caulking gun, and all of them have different voltages (12, 14.4, 18, and 24). I use a different color can of spray paint for each tool to mark the tool, the batteries, and the charger so I know at a glance where everything belongs. Otherwise the batteries and chargers are all black which makes them hard to tell apart.
“I had been using a small chain to keep my larger tubular gates open or closed, until I discovered an easier method that also saves on the gate’s hinges. To keep the gate from sagging, I screwed the post part of a screw hinge into a post at both the open and closed position of the gate - just slightly higher than the bottom of the gate - for the open end of the tubular gate to rest on. The hinge holds the gate so well that I no longer needed to chain it.”
“Here’s a foolproof way to drill out broken bolts in engine blocks, heads or any other kind of housing whenever the bolt breaks off below the surface. Cut off a 3/4 to 1-in. length of the same size bolt. Using a drill press, drill the center of the bolt portion with a small drill. Install the drilled-out bolt in the top of the hole where the bolt is broken. Using the same small drill, drill out the broken bolt using the drilled bolt as a guide. Once the broken bolt is center-drilled, you can use a bigger bit to drill out the broken bolt and it’ll always stay centered.”
“If you have a rusty bolt and nut and can’t hold the bolt end, try this. Take a same-sized nut, cut through one side, and thread it onto the exposed bolt threads. Then use a vice grip to clamp the nut and turn the stuck nut. I use this idea to change broken teeth on my belt-type windrow pickup, and it works great.”
“When I need to make a big spring longer without permanently stretching it, I have a couple of tricks that I use. These ideas work on all springs, little or big. Sometimes you have a really strong spring that you have to hook onto something at both ends. For example, there can be springs like this on hay- bine headers or balers; I have a ft. long, 1-in. dia. spring on my baler.
“I’ve found that you only need to lengthen it by an inch or two and my trick is to put flat washers between the coils of the spring by prying them apart with a screwdriver. I use an inch or so worth of 1/8-in. thick flat washers, and then pound them between the coils. That temporarily makes the spring longer so you can hook it on to what you need to. Once you lift the piece of equipment up it will stretch the spring out and the washers will all fall out.
“If you can take the spring off altogether, that’s when it’s easiest to put the washers in because the hooks on the ends can be snubbed up to something. I hook one end to a cement post or some other strong stationary object, and stretch the other end using a steel cable come-along, or a ratchety tie strap for little springs.”
“An easy way to collect metal fines from engine oil is to remove the drain plug, drill a hole through the center of it, and insert a pencil magnet so it sticks up into the oil pan. Glue it in place with epoxy. Watch the results at your next oil change.”
Tired of the frustration that short, light crops can cause when you’re trying to bale them? Roger Gutschmidt came up with a simple solution that made feeding problems on his baler pick-up disappear.
“I had trouble with my OMC roller baler on short or light hay and straw because it wouldn’t feed in properly and always piled up on the pick-up until it plugged the baler,” he says. Gutschmidt took a calculated gamble that the problem might be caused by rollers in his baler becoming somewhat slick from wear, and decided to coat them with something that would increase their ability to grab the plant material in the swath.
“I painted 3 of the drums with ‘Herculin-er,’ which is a liner for coating the interior of truck boxes to protect them with a rubber coating that’s kind of rough,” he explains.
“I brushed it on the rollers and the next morning it was hard as rock. The coating covers the cleats, too. It costs $25 per quart and I used about 1 quart per roller. I bought it at an automotive supply store.” Gutschmidt says he sandblasted the rollers first to make them rough because he wanted the best adhesion possible, but he doesn’t believe this step is essential.
“Depending on your baler, the beauty of it is that you don’t have to take anything apart. I just opened the back hatch and put the safety supports on and went to work painting on the Herculiner,” he says.
“I’ve already made 100 bales and it’s not coming off one bit. Because it’s got such good adhesion and it’s grippy, the rollers grab the hay much better than they did before.” Contact: FARM SHOW Followup, Gutschmidt Manufacturing LLC, Roger Gutschmidt, 6651 Hwy. 56, Gackle, N. Dak. 58442 (ph 701 698-2310; [email protected]).
“It hangs on the side of my tractor in a pvc mounting bracket. I find all kinds of uses for it,” says Eric “Moose” Petrevich, Glen Gardner, N. J., about his homemade hammer with a chisel hidden in the handle. He made the hammer out of a 2-ft. piece of threaded 1 1/8-in. dia. steel pipe. The chisel is welded to the metal end cap that screws onto one end of the pipe. A hammer head is welded to the other end.
“I made it because I found that often whenever I needed a hammer I also needed a chisel,” says Petrevich.
“Carrying both tools all the time was a pain, and often the chisel got lost.” He drilled a hole in the end cap and stuck the chisel through so its hitting end extends just outside the end cap. The “Moose Mallet” fits inside a short length of pvc pipe mounted on his tractor. He also takes it scuba diving. A chain link welded to the top of the hammer head serves as a handy carrying loop. Contact: FARM SHOW Followup, Eric “Moose” Petrevich, 210 Route 513, Glen Gardner, N.J. 08826 (ph 908 638-3433; [email protected]).
Louis Giesting added 40 hp to his Massey Ferguson 1105 when he switched engines. Repowered and cleaned up, the 1105 is back in the field again and working better than ever with its Fox engine.
“I bought the 1105 with about 5,000 hours on it, but it hadn’t been used for at least three years,” says Giesting.
“The previous owner said he didn’t know how good the engine was, and we found out. It blew a head gasket after 30 hours of use.” When Giesting opened the engine, he saw more trouble than it was worth. Instead of rebuilding, he and his brother Allen and a friend, Adam Nobbe, decided to swap engines. Since quitting dairying a few years ago, the Giesting’s 6200 Fox forage harvester sat unused.
“We had about 1500 hours on it over 11 seasons,” explains Giesting.
“We replaced the clutch and pressure plate, had the radiator cleaned by a professional radiator shop and had new paint applied.”
In addition to the newly refurbished engine and radiator, the three men gave the 1105 a major renovation. An after market cab was removed, the front end was taken off and the tractor split. The lighting system was rewired.
“The Fox engine only needed a set of rings and seals,” says Giesting.
“The biggest problem was modifying the oil pan. We also needed to do some work on the bell housing, but otherwise it went right in.”
A few added touches included new tires, a straight pipe for exhaust and a set of used fenders.
“We cleaned up the old sheet metal and repainted it,” says Giesting.
“We are getting a canopy for it from a salvage yard and a few other things to dress it up. It works really well, and we will be using it heavily this spring.”
Contact: FARM SHOW Followup, Louis Giesting, 24107 Pocket Rd., Batesville, Ind. 47006 (ph 812 934-2279).
Andy Gheen, Athol, N.Y., recently contacted FARM SHOW with several examples of why you don’t always have to buy new batteries when the old ones go bad.
“My Sears Craftsman 18-volt cordless drill came with two batteries and a charger. The batteries wouldn’t hold a charge after only eight months. When I contacted the company I was shocked to learn that a single new battery would cost $67, more than the entire drill kit had cost only eight months earlier.
“To solve the problem I engineered a new power system that makes use of one 12-volt battery.” He threw away the old batteries and bought a small 12-volt, sealed AGM deep cycle battery that measures only 3 in. high by 5 in. long. He connected the drill’s power leads to the battery posts. Then he set the drill’s handle down on top of the battery, carefully balancing it, and taped the battery to the drill with electric tape.
“I made this conversion five years ago and it’s still working great. Nobody laughs when they see it,” says Gheen.
“AGM batteries cost only about $20. They contain more gel than liquid so they’re safe to use.” Another idea he had is using a small solar panel to recharge cordless drill batteries.
“I bought a tiny 1.8-watt solar panel for $16 at Northern Equipment (ph 800 221-0516; www.northerntool.com) and mounted it outside my garage. I run leads from the solar panel to the drill’s power leads. The solar panel has a diode built into it so it won’t overcharge the battery, and at night it prevents the battery’s electricity from going back to the solar panel. These are really nice solar panels that have a lot of power,” says Gheen. He also found a unique way to make use of used deep cycle batteries.
“I use old deep cycle batteries that I get from a local NAPA auto parts store. When people are heading off on vacation they’ll often turn in a perfectly good deep cycle battery and buy a brand new battery to avoid spoiling their vacation. I pay $8 to the store for the battery core, and then I connect the battery to my solar panels and use them to light my barn. I’ve found that you can operate a lot of lights off a single deep cycle battery.” Contact: FARM SHOW Followup, Andy Gheen, 89 Cameron Road, Athol, N.Y. 12810.
Old combine hydraulic steering motors can be used to make a shop press easier to operate, says Orvie Wideman, Wallenstein, Ontario, who replaced the spool control valve on his shop press with a hydrostatic steering motor off an old Massey Ferguson 815 combine. He made a metal bracket to mount the motor on the press’s frame. A hydraulic pump, belt-driven by a 1 1/2 hp electric motor, is used to operate the steering motor. To move the press up or down Wideman simply turns the combine’s steering wheel.
“It works much better than the press’s original control valve because I can ‘feather’ the press up or down exactly where I want it. With such precision control I don’t have to rebend material nearly as often,” says Wide-man.
“I think the same idea would work on an H-style arbor press or leaf break.
“I bought most of the materials that I used at a salvage yard. I paid $125 for the steering motor and $75 for the hydraulic pump, which came off an old swather. I already had the electric motor.” Contact: FARM SHOW Followup, Orvie Wideman, 4155 Ament Line, R.R. 3, Wallenstein, Ontario Canada N0B 2S0 (ph 519 698-2911).
With its single plunger and multiple outlets, the handy Grease Bug lube system helps ensure that grease fittings don’t get overlooked when rushing to the field or to work. Just turn the dial to each of up to 6 fittings and then pump.
The Grease Bug Pump can be mounted on any equipment that needs to be greased regularly or on a stand-alone frame. Separate feeder hoses carry grease to the bearings or pivot points to be lubricated.
“Simply remove the existing grease fitting and attach the fitting supplied with the Grease Bug Pump,” says Chrissa Chverchko, of InventHelp.
InventHelp sells the unit on its website for $200 plus S&H.
Each Grease Bug comes with several different types of fittings and standard tubing. The 7-ft. tubes can be cut to length, with replacement tubing and fittings generally available at local hardware stores.
Refilling the pump is easy too. It uses standard 3-oz grease tubes. The reservoir can also be directly filled with bulk grease.
Contact: FARM SHOW Followup, In-ventHelpStore, 217 Ninth St., Pittsburgh, Penn. 15222 (ph 412 288-1368 or 800 851-6030; www.inventhelpstore.com).
When his father suggested that Ryan Lusk put a Cummins engine in his 1968 Corvette, Lusk dismissed the idea. But when two friends said it couldn’t be done anyway, Lusk couldn’t ignore the challenge. He proved them wrong, and this year he turned heads when he started drag racing with his Cummins-powered Corvette. The Mitchellville, Iowa, resident works as a diesel mechanic and started his own sideline business — Low Budget Diesel Performance, focusing on diesel conversions and boosting diesel performance. Lusk had already converted several gas pickups to diesel before he started installing a 1998 12-valve Cummins in his Corvette, together with 1995 47RH Dodge lock up overdrive transmission with a Goerend Brothers triple billet torque converter. The ‘Vette was also fitted with a Sonnax billet input shaft and hub, Goerend-built valve body and many other modifications to get ultimate power from the engine. Lusk’s first challenge was putting a big engine in a small space.
“I cut out the floor of the car and built a new floor out of 1 by 1-in. angle iron for frame work, and .040 aluminum plate,” Lusk says. The next challenge was modifying or making everything tie into the transmission and engine. One sponsor, Gilmore Diesel Performance from Kingdom City, Mo., built and modified the transmission, and another sponsor, PureFlow Technologies, supplied a fuel system. Lusk and a few friends and relatives did the rest of the car work themselves — including making frame changes, building motor mounts, welding in a 14-pt. roll cage, adjusting the Ford 9-in. rear end, and building the tilt front end. Because of the space needed for the roll cage Lusk (re-luctantly) removed the Corvette’s dashboard and replaced it with a smaller aluminum dashboard.
“Graham from Sargent’s garage in Des Moines, Iowa, aligned the car and it launch-es beautifully down the track,” Lusk says.
“The guys still can’t believe that engine fit in there.” While it’s a hassle to get some parts, such as the injection pump, Lusk designed the car so he can pull out the transmission with minimal work. Changing engines improved gas mileage to about 26 mpg and the car drives and rides great, Lusk says. It sounds like a truck so people look twice when he starts the car. Because of the car’s 3,650-lb. weight (with driver), he competes in the pro-stock class at National Hot Rod Diesel Association races.
In early races this year he completed the 1/8-mile distance in 7.87 seconds at 90 mph. Lusk’s brother, Nick, also drives the car in the Sportsman ET class. The car has a single small Schwitzer turbo and uses turbo blankets supplied by sponsor Turbo Performance Products to help spool the turbo at the line. Lusk plans to change his injectors and turbo setup to boost his power to 55 to 65 hp in the near future. More details of the Corvette’s specifi - cations can be found on Lusk’s business’ website. He invites readers to contact him regarding diesel-rebuilding challenges they might have. Contact: FARM SHOW Followup, Ryan Lusk, 5185 NE 116th St., Mitch-ellville, Iowa 50169 (ph 515 967-3342; [email protected]; www.low-budgetdiesel.com).
Fixing tractors started out as a necessity for Brian Wischmeyer when he was 16. The tractors he and his father worked on were the ones they used on their Ottawa, Ohio farm. Eight years later, Wischmeyer is still at it with a reputation for good work that has spread from neighbor to neighbor. He recently started advertising his business, Brian’s Tractor Restoration, to fill in his off time from farming with his dad. Wischmeyer studied ag business at college, but gained most of his restoration skills working with an auto body expert who also rebuilds engines.
“My specialty is painting,” Wischmeyer says.
“Most guys don’t take the time to get a tractor ready to paint, and a successful paint job is 90 percent preparation.” He has invested in good equipment to power wash and sandblast all the grease and old paint. He also wet sands after applying primer and before adding a final clear coat. In addition to painting restored tractors, he paints new equipment for local dealers. The 24-year-old can do more than just paint, however. He points out that there’s no use painting a tractor to make it look new if there’s something wrong with it. He offers complete overhauls, if needed.
“On the last one I took off every nut and bolt,” Wischmeyer says. He buys parts books for every model he works on. Many of his customers are collectors who appreciate his professional painting.
“I work on a lot of Ford 8N and Deere 420’s and 730’s also,” he says. Wischmeyer charges $25/hour and he estimates approximate costs ahead of time. Painting a small Ford 8N runs about $700, for example. The work is satisfying, Wischmeyer says. He isn’t fond of the prep work for painting, but likes the challenge of fixing tractors.
“The part I like the best is when you get it back together and painted, and it looks like new,” he says. Contact: FARM SHOW Followup, Brian Wischmeyer, Brian’s Tractor Restoration, 13295 Rd. 8M, Ottawa, Ohio 45875 (ph 419 235-4339; [email protected]).
Georg Hertz-Kleptow of Dapp, Alberta couldn’t justify the cost of a commercial hydraulic-cylinder sleeve puller, so he made his own. With only about a $360 investment and 12 hrs. of his time, Hertz-Kleptow built a unit that serves his needs well.
“Hydraulic sleeve pullers are very expensive and it’s not something you use every day. You could spend $5,000 for a comparable unit,” he says.
“I’m really happy with mine. It’s a 30-ton puller with a 5-in. inside dia. cylinder.” The specialty tool pulls engine sleeves and also presses new ones in. It’s something that Hertz-Kleptow needed in his shop, where he works for neighboring farmers and also himself. Hertz-Kleptow saved money by being able to use an existing hydraulic pump in his shop – one that he normally uses on his hydraulic press. Hertz-Kleptow salvaged two hydraulic cylinder rods from an old air seeder and used them as the sleeve puller’s frame. To power his unit, he already had a hydraulic cylinder “laying around”. He spent about $80 on hydraulic fittings, hoses, 2 pressure gauges and other miscellaneous materials. Because various engines have different sleeve sizes, the puller also needed several adapter plates. Hertz-Kleptow had a local machine shop make up 3 sizes of adapter plates for about $40 each. The adapter sits under the sleeve to catch the bottom edge of the liner, and a threaded rod connecting the hydraulic cylinder to the adapter plate pulls the liner up through the boring.
“I also use the sleeve puller for pulling large tractor tires off axles as well as pulling king pins out of the front axles of FWA tractors to remove final drive pivot housings,” Hertz-Kleptow says.
“You only need a welder, a torch and a drill press to build it.” Contact: FARM SHOW Followup, Georg Hertz-Kleptow, P. O. Box 206, Dapp, Alberta Canada T0G 0S0 (ph 780 954-2149; [email protected]).
By injecting a little propane into diesel engines you get faster speeds, more power, and a cleaner burn, says Craig Ridgeway, RMR Pro-Diesel Technology. Ridgeway says his Propane Enhancer, a patented progressive fuel valve, is catching on fast. He’s installed the system on turbo-powered semis, field tractors and even pickups.
“The secret to using propane is to deliver the right amount at the right time,” says Ridgeway, who has been burning propane in diesel engines since he was a kid on the family farm.
“If you deliver too much or not enough, you lose fuel efficiency.”
Ridgeway’s valves are activated by the engine’s turbo boost pressure. He offers a single-stage valve for use with boost pressure under 30 lbs. and a two-stage valve for pressure of 30 lbs. and more. As the boost pressure increases, more vapor propane is fed into the air intake, giving the engine only the amount of propane needed to maximize efficiency.
Ridgeway explains that equalized injection into all cylinders is vital. If too much propane goes into the first cylinders in line, it can damage them because they won’t get enough lubricating diesel.
Each installation of the valve is specific to that particular engine. Ridgeway takes into account tire size, transmission, rear end gear-ing and whether the engine operates under heavy or light loads.
“We have an advanced dynamometer in our shop that gives us an accurate reading of engine usage and exact settings for our system,” explains Ridgeway.
“If you can’t come to us, we provide a suggested setting based on our records of installation on the same engine in a similar situation. Once installed, it can be fine tuned to get the optimum flow.”
Ridgeway has installed propane valve on more than 700 engines over the past four years with zero engine failures due to propane. RMR promotes an increase of one to three miles per gallon on over the road diesels. Ridgeway says he likes to be con-servative in promises. His results, as well as customer reported results, point to much higher returns.
“I’ve raised my mileage pulling trailers by 6 mpg,” he says.
“Overall, my Duramax Dodge has gone from 14 to 16 mpg to 25 to 32 mpg.” Ridgeway has also installed his propane units on field tractors and bulldozers. He reports his 8640 Deere burned 16 gph pulling his 30-ft. chisel plow. Injecting only 1 1/2 to 2 gal. of propane per hour dropped diesel use to 9.2 gph. The increased power also let him “I put a system on a D4 Cat, and it boosted output from its rated 57 horsepower to 120 when using propane,” says Ridgeway.
“I’ve put mega hours on it pushing twice as much dirt as it used to do on diesel alone.”
He says the propane simply helps burn diesel fuel more efficiently. Typically, he explains, only about 75 percent of diesel used is burned. With the propane injected, efficiency jumps to 98 percent.
“That’s where we get our increased power,” says Ridgeway.
“We turn that wasted fuel into energy.”
Burning the diesel more completely re-duces carbon buildup in an engine for longer engine life. It also cleans up the exhaust.
“We had a customer from Utah take his truck in for the mandatory state inspection way.
“With our propane valve installed, his truck dropped from 11 percent particulates to zero.”
Ridgeway says he can literally see the difference on his 8640 Deere.
“When I am burning straight diesel, I can see the shadow of the exhaust on the ground,” he says.
“When I turn on the propane, the shadow goes away.”
Ridgeway charges $2,995 for a valve and tank system installed.
“When you put a pencil to it, you’ll be surprised how quickly it pays for itself in fuel savings and extra power,” he says.
Contact: FARM SHOW Followup, RMR Pro-Diesel Technology, 401 Main St., Jet, Okla. 73749 (ph 580 626-4583; fax 580 626-4584; [email protected]; www.prodieseltech.net).
With her three patent-pending clamps, Re-nae Becker can easily reconfigure and repair the horse corrals on her California ranch.
“The whole idea is to make do with what you already have,” she explains.
“We really wanted the flexibility to change our corrals around. We searched everywhere to find a fence clamp that would securely attach a perpendicular intersection but there was no such product available. With the help of my friend, who’s in the fabrication industry, we created 90 Proof Clamps.”
“The rail (clamp) is used to connect two corral panels by attaching the horizontal rail of one panel to the horizontal rail of the second,” Becker explains.
“The purpose is to allow the user to build their stalls or pad-docks any size they need without having to rely on the dimensions of the vertical posts that make up the frame of the panel. Typically, a 24-ft. panel is supported by three vertical posts, every 8 ft. Therefore, there was no way to split the corral in even halves - until now.” The pole clamp has a figure-8 twist that allows the connection of vertical and horizontal pipes. The versatile T-clamp offers an alternative to repair broken pipes as well as a variety of other uses such as adding pipes to the top of the corral for extra reinforcement.
“The T-clamp will withstand more than 1,200 lbs. of pressure and you don’t have to hire a welder to install,” Becker says.
“The clamps also make it simple to fix broken pipes.” Carriage bolts and nuts secure the clamps. At $9 to $14 the clamps are also affordable. Becker, an avid horse rider who takes trips across the Mojave Desert and Death Valley, has been using the clamps on corrals for her 6 horses for nearly two years. She sells them through her website and about 50 businesses in the West.
“We haven’t had any returns. The comment I get from everybody is ‘Why I didn’t think of that?’ ” says Becker.
Contact: FARM SHOW Followup, Renae Becker, Trio Ranch, 31915 Trail Rd., Agua Dulce, Calif. 91390 (ph 805 890-5495; www.trioranch.com).
These new sealed containers have been used in the oil drilling industry and other industrial markets for several years to handle petroleum products. They’re now being introduced to agricultural markets by Genoa Business Forms (GBF).
“I grew up on a farm and recall using open cans to transfer oil from a barrel to a tractor,” says Rex Young, GBF.
“A little dust or a bit of rust didn’t seem to matter. Those days are over with the engines being introduced these days. Contaminate levels have to be next to nothing on Tier 3 and Tier 4 engines.”
The “iCan” containers are designed with tightly sealed ports for filling and disbursing liquids safely, quickly and cleanly. The containers are made of high-density polyethylene. They come in 2, 5 and 10-liter sizes. Pour lids use twist-open nozzles and light-switch style breather vents for easy pouring. There are three different nozzle sizes for different pouring rates. Extension hoses and hand pumps are also available. Industry research indicates that lube oil contamination accounts for 70 to 80 percent of all engine failure and wear. While the iCan design can help reduce or prevent contamination, they also help with another common problem - misuse.
“Each container lid comes with color coded tags and clear plastic tag holders,” says Young.
iCan containers range in price from $8.99 to $19.99. Pour lids equipped with a quick-fill port and a twist-open nozzle are priced at $27.99. Pump lids with a quick-fill port and a threaded accessory port range from $13.99. They are designed to work with the hand pump, which is priced at $39.99. All units are available as components or in a sample kit for $199.99 (a 10 percent discount). The kit contains all three container sizes, lids, extra extension hoses and identification pouches.
Contact: FARM SHOW Followup, Form8700-22.com, 445 Park Ave., Syca-more, Ill. 60178 (ph 815 895-9933; www.form8700-22.com).