Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 33, No. 6 (2009)

Vol. 33, No. 6 (2009)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

29 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

John Benoit

John Benoit, Bourbonnais, Ill.

“FARM SHOW recently published a story on how to remove rust using a solution of washing soda (like Arm & Hammer) and water. I’ve found this method also works for removing hardened grass clippings from lawn mower blades.

“I mix one cup of soda with 5 gal. of warm water in a square plastic tub. I let the blade soak overnight. The next day I use a wire brush on the clippings and they come right off. Then I sharpen the blades and coat them with vegetable oil to keep grass from building up again.”

From the archive · Full text
Reader shop tip

Lyle Moege

Lyle Moege, Hurley, S. Dak.

“For years I had trouble starting my Deere 3010 gas tractor. Then on the recommendation of someone at our local NAPA store I installed a new semi truck battery. It has a tremendous 900 amps of cold cranking power and solved the problem immediately.

“It was a straight swap-out – a 12-volt battery for a 12-volt battery. However, the semi truck battery is much bigger and weighs a ton. To handle the weight I had to build an angle iron support bracket. In the past, starting the tractor was always a crapshoot and I often ended up using jumper cables. It didn’t matter if the weather was cold or not.

“I paid only $20 to $30 more for the semi truck battery than I would have for a Deere replacement battery. It was the best money I ever spent on this tractor.”

From the archive · Full text
Reader shop tip

Rodney Earl Claggett

Rodney Earl Claggett, East View, Ky.

“A lot of the scrapers on my Deere 13-ft. disk are gone which causes the disk to clog up, especially behind the wheels. I made my own inexpensive ‘scrapers’ using small chains. I ran them from the frame to the center of each disk. It keeps mud from building up and was a lot cheaper than new scrapers.”

From the archive · Full text
Reader shop tip 1 of 3

Steve Reeves

Individual tip 1 of 3 from this reader’s published contribution.
Steve Reeves, Benton, Ky.

“I use the teeth on my 21 hp Kubota backhoe to cut through tree roots. On big roots I use the teeth like a knife blade to shave the root down until it’s thin enough that I can pull it out. However, after a lot of use the teeth started coming loose. The teeth wiggled to either side, which made it difficult to keep them from sliding off the roots.

“I got tired of having to retighten the bolts all the time so I made a U-shaped weld around each tooth, making sure I welded right up next to the tooth but not into it. The weld keeps the tooth from wiggling from side to side, yet if a tooth ever breaks I can still loosen the bolt and slide it out.

From the archive · Full text
Reader shop tip 2 of 3

Steve Reeves

Individual tip 2 of 3 from this reader’s published contribution.
Steve Reeves, Benton, Ky.

“Eventually the teeth get dull and don’t do a good job of cutting through the roots. Then I use a hard surface welding rod and build the teeth back up with new metal. I use a grinder on the tooth until it’s razor sharp again.

From the archive · Full text
Reader shop tip 3 of 3

Steve Reeves

Individual tip 3 of 3 from this reader’s published contribution.
Steve Reeves, Benton, Ky.

“I have problems with arthritis, which makes it difficult to lay on a shop floor and work on equipment. To solve the problem I use a motorcycle hoist. It lets me raise the equipment to working height and then sit in a computer chair and roll around the machine as needed. The air lift operates off a compressor and is foot-operated. It has a capacity of up to 1,500 lbs. so I can use it to lift riding mowers, rototillers, pressure washers, and so forth. I bought the lift at Harbor Freight for $479 (ph 800 444-3353; www.harborfreight.com).”

From the archive · Full text
Reader shop tip 1 of 3

Trevor Bruntlett

Individual tip 1 of 3 from this reader’s published contribution.
Trevor Bruntlett, Chelan, Wash.

“Recently I bought a 2002 lawn tractor used and soon discovered someone had put something in the fuel tank that gummed up the entire fuel system. The plunger for the carburetor’s fuel metering system broke, and unfortunately I couldn’t get new parts. I solved the problem by installing the plunger out of a 15-year-old Briggs & Stratton 12 hp engine that I already had. Now the tractor runs great.

From the archive · Full text
Reader shop tip 2 of 3

Trevor Bruntlett

Individual tip 2 of 3 from this reader’s published contribution.
Trevor Bruntlett, Chelan, Wash.

“The 12 hp engine in my Sears Craftsman lawn tractor had only 25 lbs. of compression which made it hard to start and kept it from running well. I replaced the 12 hp engine with a much smaller 3 1⁄2 hp engine off an old push mower. I use the tractor mainly to pull small trailers and to move snow with a 4-ft. wide front-mounted blade. Most of the power used by the 12 hp engine went to driving the mower blades, so even just a 3 1⁄2 hp engine provides enough power for what I need.

From the archive · Full text
Reader shop tip 3 of 3

Trevor Bruntlett

Individual tip 3 of 3 from this reader’s published contribution.
Trevor Bruntlett, Chelan, Wash.

“I burn wood and used oil at the same time in my barrel stove to heat my 24 by 36-ft. shop. I start the fire with wood and paper and once the fire gets going good I add about two quarts of oil. It’s a good way to get rid of used oil, and it reduces the amount of wood I use to heat the shop. I add oil every time I reload the stove. I just open the front door and throw in a pail full of oil. The wood burns hot enough that it vapor-izes the oil and burns it off without creating a lot of smoke like you get when burning just straight oil. My shop doesn’t have any insulation, but the shop stays comfortably warm even when it’s 20 degrees above zero outside.”

From the archive · Full text
Reader shop tip 1 of 3

Gilbert F. Conn

Individual tip 1 of 3 from this reader’s published contribution.
Gilbert F. Conn, Pittsburgh, Penn.

“A case-hardened bolt broke off on my tractor’s water pump and I wasn’t able to drill it out, so I used a Dremel tool and four small grinding stones to do the job. The grindstones I used are 3/8 in. in dia. and pointed at one end. I would grind out a little of the bolt and then use an air gun to blow out the material. I wore out four grindstones before I was able to drill out all of the bolt. Then I rethreaded the hole and applied Loktite. The job took two hours, but it saved me from having to buy a new engine block.

From the archive · Full text
Reader shop tip 2 of 3

Gilbert F. Conn

Individual tip 2 of 3 from this reader’s published contribution.
Gilbert F. Conn, Pittsburgh, Penn.

“The steering wheel on my 1948 Deere A tractor was all chewed up and had deep cracks around the wheel’s three spokes. I used Billy Mays Mighty Putty to build the wheel back up to its original condition, even making molded grips for my fingers (ph 800 967-2312; www.mightyputty.com). Then I bought a leather steering wheel cover at Wal-Mart and put it on over the wheel. It saved me the $70 cost of a new steering wheel and took only about one hour to do the job. The steering wheel looks like new again.

From the archive · Full text
Reader shop tip 3 of 3

Gilbert F. Conn

Individual tip 3 of 3 from this reader’s published contribution.
Gilbert F. Conn, Pittsburgh, Penn.

“I often use my New Holland 555E backhoe, which is equipped with an extend-a-hoe, to lift machinery off the ground for easier maintenance or repair work. I can easily flip the machine over in mid-air. The backhoe can lift up to 30 ft. high.”

From the archive · Full text
Reader shop tip

L. Putnam Foley

L. Putnam Foley, Bulger, Penn.

“I had problems with hay plugging up in my 1992 New Holland 848 round baler due to worn rollers. I was able to get the bale started, but the rollers were so slippery the hay wouldn’t keep going through and soon started plugging up. I had to stop often and pull out the hay.

“I didn’t want to spend the money on a new baler so we had to try something else. My grandson coated the rollers with a non-slip liner, the kind used on truck beds, and it has totally solved the problem. The coating is starting to wear out now so we plan to apply another coat before next summer. The baler’s bottom roller is made of steel and the top one rubber. Only the steel roller was worn but my grandson painted both rollers anyway. I don’t know if the bed liner had any effect on the rubber roller. I didn’t start having this problem until recently because in the past we made mostly silage bales, and the wet hay went through the rollers without slipping.”

From the archive · Full text
Reader shop tip

Andy Sewell

Andy Sewell, North Yorkshire, England

“I use empty 2-liter milk containers to store small parts. I wash the container out and let it dry, then cut out the top. The containers store neatly on shelves, and you can use a Sharpie pen to write on the bottom. This idea works so well that I haven’t thrown out a milk container in two years.”

From the archive · Full text
Reader shop tip

Jim Rist

Jim Rist, Granbury, Texas

“I own a 2007 Kawasaki Mule 3010 utility vehicle with only about 400 hours, but already the fuel pump on it has quit working. A new fuel pump costs $279, and I couldn’t expect it to last any longer.

“To solve the problem I bought a 12-volt fuel pump made by Airtex at a local auto parts store. The Airtex fuel pump was in the same psi range (2.5 – 4.0 psi) as the factory fuel pump (3.0 psi). I paid $68 for it, and it works great.”

From the archive · Full text
Reader shop tip

Lonnie Fisher

Lonnie Fisher, Baytown, Texas

“I needed a flat belt drive system to operate my Chatta-nooga 44 cane mill, but none of my tractors had a flat belt pulley. So I turned the gearbox 90 degrees on an old Rhino 5-ft. mower and adapted an 8-in. dia. pipe to the blade bar to run the flat belt. Now I can operate the cane mill using any tractor equipped with a pto. Works great.”

From the archive · Full text
Reader shop tip

Eric McNutt

Eric McNutt, Sulphur Springs, Ohio

“My home-built welding table makes use of a simple 2-wheeled dolly and folds up for transport and storage. As a result, the table doesn’t take up much more storage room than the dolly itself.

“The 2-piece table measures about 2 ft. wide by 3 ft. long. I built it because I didn’t want to give up floor space to a dedicated welding table. The top part of the table is separate from the front and is formed by an angle iron frame and expanded metal. The front part is made from 1-in. sq. tubing, with a length of flat steel serving as a brace at the bottom. The brace is what the front rides on during transport.

“I wrapped and welded a piece of 1-in. flat stock around the dolly to support the hinge, which consists of a length of tubing with a rod going through it. By removing a cotter pin at each end of the rod I can remove the dolly and use it as an ordinary 2-wheeled cart.

“A simple bungee cord holds the entire unit together for storage.”

From the archive · Full text
Reader shop tip

Roger Gutschmidt

Roger Gutschmidt, Gackle, N. Dak.

“Here’s a tip that allows you to comfortably haul quite a few 10-ft. lengths of steel in your mini van without getting the interior dirty. For the last 10 years, I’ve been using a 5-in. dia. cardboard tube that once held a roll of new carpet. Instead of discarding it, I wrapped the tube with duct tape so it can be wiped off if it becomes dirty, and position it down the center of the van whenever I go to town to buy steel.

“I use it for hauling various lengths of angle iron, bar stock, channel iron, pipe, and anything else that fits inside. By hauling steel in the tube, it keeps our van’s upholstery from getting stained with oil or dirt.

The tube lays the entire length of the mini van, from the back, all the way up to the front where the radio is. It doesn’t interfere with anything.

“I use it all the time, as our mini van gets better gas mileage than our pickup truck, and our van can haul up to 6 people comfortably while we hardly notice the tube’s in there. Our pickup truck only has a 5 1/2-ft. bed, so to use that would mean the end gate would have to be open and 3 feet would still be sticking out the back, which is kind of a safety hazard, plus with the end gate open, grocery bags and other cargo would have to be secured.

“When not in use, I simply store the tube in our garage.”

From the archive · Full text
Reader shop tip

Roger Hughes

Roger Hughes, Janesville, Wis.

“In re-gard to the Florida reader in your last issue, who was having trouble with ethanol in his chainsaw, my Stihl chainsaw dealer highly recommends that you use premium gas with at least 93 octane and no ethanol in it. Most gas stations do not add ethanol to their pre-mium gas. The shelf life of gas with ethanol is not nearly as long as gas without ethanol. Another reason to avoid gas with ethanol added is that on some older 2-cycle engines, the seals and O-rings will not tolerate ethanol.”

From the archive · Full text
Reader shop tip

Allen R. Colombo

Allen R. Colombo, Bogalusa, La.

“The V-belt on my Sears garden tractor, with a 54-in. deck, kept coming off the drive pulley on uneven ground. I fixed the problem by installing a larger spacer on the anti-sway bar. It also reduces wear on the V-belts.”

From the archive · Full text
Reader shop tip

Dan Fitzsimmons

Dan Fitzsimmons, Good Thunder, Minn.

“The differential lock on my IH 5488 MFWD tractor was activated by holding down a button on the cab floor with your foot. On half-mile rounds that would get very uncomfortable. So I installed a 12-volt toggle switch on the shifter lever and wired it into the differential lock. Now I just flip the switch off and on at the end of the row and keep my feet in a relaxed position.”

From the archive · Full text
Reader shop tip

Fred Hoffmeyer

Fred Hoffmeyer, Grass Valley, Calif.

“Tires are expensive but they’ll last a lot longer if you keep them inflated to a proper level. You also save money on fuel. The problem is that it’s often a hassle to get an air hose to inflate them. To make it easier, I ran air lines and put pressure gauges real close to my vehicles. Makes all the difference.”

Shop feature stories

From the archive · Full text
Feature story

Ford Pickup Repowered With Nissan Engine

Featured source:

“I rebuilt the 2.3-liter engine in my 1983 Ford Ranger pickup but it only worked for 18 months. So I decided to replace it with the engine out of a 1981 Nissan pickup,” says Frank Dyck of La Crete, Alta.

“I was quite satisfied with the results. With the Ford engine I constantly had problems with the head and valves. The Nissan engine doesn’t provide quite as much heat in the winter as the Ford, but it’s much more reliable. Also, it gets about five miles more per gallon than the Ford.” He bought the Nissan pickup equipped with a manual transmission from a neighbor for $300. Its 2.2-liter, 140 cu. in., 100 hp engine was still in good condition. He pulled out the Ford’s engine, power train and radiator and slipped in the Nissan components. The Nissan’s transmission shift lever was located 6 in. farther back than the Ford’s so he had to cut out a new shifter hole in the floor. The engine mount on the driver’s side bolted right in, but the other side needed a 3/4-in. thick spacer to keep the oil pan off the cross member. The transmission rear mount needed an adapter plate to reach the rear cross member. He removed the Ford’s original coil system and installed the Nissan’s twin coil ignition system.

“All I had to do was connect the ignition ‘live’ wire from the Ford to the Nissan system. The Nissan engine has two coils and two spark plugs per cylinder. I also installed the Nissan’s boost decelera-tion control device which hooks up to the carburetor. It kicks in when you take your foot off the gas to decelerate.” He had to drill a hole near the top of the gas tank so he could install a fitting for the fuel return line. There wasn’t room for the Ford power steering pump, which would have interfered with the Nissan engine’s distributor, so he removed it.

“I don’t have power steering now, but I could get it by mounting a power steering pump off a Nis-san 4-WD truck. But then I’d need to use the electric fuel pump from the truck as well,” says Dyck. Contact: FARM SHOW Followup, Frank M. Dyck, P.O. Box 388, La Crete, Alta., Canada T0H 2H0 (ph 780 928-3944).

From the archive · Full text
Feature story

Car Hoist Adapted To Riding Mower

Featured source:

“It’s a simple, low cost way to raise our riding mower up in the air so we can easily service it,” says Roger Foster, Tower Hill, Ill., who made brackets for his commercial 10,000-lb. rotary hoist to raise and lower his zero-turn riding mower.

“I’ve used the hoist for years to service my cars and pickups. Now I can use it to service my mower and to sharpen the blades without any hassle,” says Foster. Foster used 2-in. steel tubing to build a 3-ft. high metal arch that straddles the mower’s front wheels and pins onto the hoist’s front swing arms. A pair of light chains are used to connect the arch to the mower’s front axle.

A length of 3-in. wide channel iron slides up under the mower’s rear bumper and pins onto the hoist’s rear arms. The mower’s rear wheels rest on top of the arms. To attach the mower to the hoist, Foster drives the mower forward until the front wheels are under the arch. Then he swings the arms in, pins the arch to the arms and attaches the chains to the front axle. Then he slides the channel iron under the mower’s rear bumper and pins it to the hoist’s rear arms. Contact: FARM SHOW Followup, Roger Foster, Rt. 1, Box 108, Tower Hill, Ill. 62571 (ph 217 567-3417; cell 217 827-2213).

From the archive · Full text
Feature story

Company Rebuilds Hydros With Care

Featured source: Herrs Machine

Hydraulic component rebuilds can save a lot of money, but they’re not usually do-it-yourself projects, says Cara Herrs of Herrs Machine. The company has been rebuilding hydraulic pumps and hydrostatic transmissions for 37 years, progressing from a home-based shop business to a high tech operation that can handle nearly anything hydraulic.

“We once rebuilt the pumps and motors on a mine sweeper, but our most common repairs are combine hydrostats,” says Herrs.

“We have an ag background, so we understand how quickly equipment needs to be up and running. In addition to our rebuild service, we keep a large inventory of parts, pumps and motors on hand. We can usually ship out the same day we get an order.”

Herrs suggests making a toll-free call for a cost estimate. If time is tight, most agricultural hydro units are available in exchange. The company works with tractors, combines, skid steers and a wide range of other equipment. However, long-term specialties have been IH hydrostats and torque amplifiers.

Whether for rebuild or exchange, Herrs emphasizes carefully wrapping the part for shipment, especially if components are exposed. One ding or gouge in a plate can increase rebuild cost considerably.

“Plates in a stack have to be perfectly flat,” says Herrs.

“A scratch can cause a blow-by and increase pressure on the hydraulics and raise the temperature.”

When parts come in for rebuild, they are first ‘mic’d’ or inspected using a micrometer to make sure plates are within 1 millionth of an inch of flat. After inspection the part goes to lapping, where a zinc oxide drip is used to polish the plate to a mirror finish. If too far out of tolerance, parts will be replaced. Even though a single plate with a gouge can often be refinished, Herrs says the refinishing might reduce the required height of the total stack.

“We have to stay in tolerance the whole way through,” she says.

Once the part or component has been re-built, it goes through testing. Each step in the process is recorded. If testing identifies any problem, it also shows where the problem occurred.

“We will then tear it down and fix the problem,” says Herr.

“We know it has to be done right.”

Herrs handles pumps, motors, cylinders and valves. All remanufactured units come with a warranty.

Contact: FARM SHOW Followup, Herrs Machine, 1745 Prospect Blvd., Washington, Kan. 66968 (ph 785 325-2875; toll free 877 525-2875; [email protected]; www.herrsmachine.com).

From the archive · Full text
Feature story

Where To Buy Tractor Service Manuals

By Jim Ruen, Contributing Editor
Featured source: FARM SHOW

Not all tractor manuals are equal, warns Paul Jensen, Jensales Company. The second-generation tractor manual reseller warns that many original service manuals were sometimes not complete.

“Company service manuals were often incomplete,” he explains.

“Sometimes they put them out piecemeal as new models came out.”

Many of the service manuals from Jen-sales are not original.

“Part of our pitch is that our manuals may be better than the originals,” he says.

“In some cases we’ll include value added content, such as serial numbers and paint code information essential for restoration.”

Jensen notes that many original manuals are in a hard-to-read 6 by 9 format. It’s also likely to be perfect bound, which won’t lay flat unless the binding is broken.

“We put a spiral binding in our manuals so you can spread them out flat on the work bench,” he says.

“We also print ours on 8 1/2 by 11 paper.” Jensales has more than 16,000 manuals available for nearly every tractor made from 1900 to the present. In addition to reproductions, Jensales does offer many originals. There are also compilations of multiple manuals for a line of tractors such as the Oliver 3 that covers 11 models. Of special interest to restorers is the Char-Lynn power steering and hydraulic pump manual. It covers the installation kit and operators manuals for nearly a dozen applications of the popular accessory of the 1940’s, 50’s and 60’s.

Jensen warns that manual quality varies greatly from vendor to vendor. How pages are scanned and how the scans are put back together can make a big difference in the quality of the final product.

“We adhere to Library of Congress ar-chiving standards,” says Jensen.

“It calls for 600 dpi scans and clarity of picture and text. We will scan to get the text and then scan a Jensales has more than 16,000 service manuals available for nearly every tractor made from 1900 to the present.

second or third time to get the pictures.”

Jensen takes pride in his firm’s customer service.

“We can print on demand,” he says.

“If we get an order by noon, it will be out that same day.”

Contact: FARM SHOW Followup, Jen-sales, Inc., 200 Main St., Manchester, Minn. 56007 (ph 507 826-3666 or 800 443-0625; www.jensales.com).

Of course Jensales is far from alone when it comes to supplying the antique tractor manuals. Here are a few to get you started. Many offer authentic and original manuals, while others offer reproductions. Most will be more than happy to help you find what you are looking for, whether reproduction or original.

Binder Books, 27875 SW Grahams Ferry Rd, Sherwood, Ore. 97140 (ph 503 682-9328; www.binderbooks.com). Binder Books specializes in IH tractors and trucks, offering manuals, books, toys, decals and collectibles.

Clarence L. Goodburn, 101 West Main, Madelia, Minn. 56062 (ph 507 642-8481; eBay password: goodlit).

Goodburn specializes in sales literature on farm tractors and equipment, crawlers and heavy equipment.

TF Literature Sales, Rt. 2, Box 8, Lu-verne, Minn. 56156 (ph 507 283-4730; [email protected]).

TF Literature handles all types of manuals and literature on most brands of farm equipment.

Lloyd Wenger, 831 South College St., P.O. Box 409, Myerstown, Penn. 17067 (ph 717 866-7147; [email protected]; www.wengers.com).

Go to Collector’s Corner on the Wenger Co. website to find listings of equipment literature, owners manuals, parts books, collectibles, antique tractor parts and more.

Yesterday’s Tractor Co., 751 Commerce Loop, PT Business Park, Port Townsend, Wash. 98368 (ph 360 379-4808; 800 853-2651; www.yesterdaystractor.com). Yesterday’s Tractors offers manuals, parts, engine kits and much, much more, including more than 90,000 tractor pictures.

Floyd County Historical Society, 500 Gilbert St., Charles City, Iowa 50616 (641 228-1099; [email protected]; www.olivertractor-manuals.org).

Charles City is the birthplace of the first gas-powered tractor, and the museum has original and photocopied manuals for sale for Hart-Parr, Oliver, White Farm Equipment, Cockshutt, Minneapolis-Moline, Cletrac, New Idea (earlier) and some Frost Woods models.

State Historical Society of Wisconsin, Archives Reading Room, 816 State St., Madison, Wis. 53706 (ph 608 264-6460).

The Society has a large collection of parts catalogues, photos and operators manuals for virtually all IH implements, wagons and stationary equipment. The collection includes materials from five predecessor companies - McCormick, Deering, Champion, Plano and Milwaukee - as well as other IH subsidiaries (Chattanooga, Hoosier, Keystone, P&O and Weber). Call or send a letter with as much information as possible, such as parts and model number or even a photo.

Deere & Co., P.O. Box 186, Moline, Ill. 61266 (ph 800 522-7448). Call to access the John Deere archives for manuals and materials back to the introduction of two cylinders and even some drawn plows.

Abraham Lincoln Presidential Library, 112 North Sixth St., Springfield, Ill. 62701 (ph 217 558-8844). Formerly the Illinois Historical Library, this library maintains archives on old Deere equipment, including horse-drawn tools.

Del Bice, 1026 South 88th Ave., Yaki-ma, Wash. 98908 (ph 509 966-2844).

This former Deere dealer maintains a collection of more than 4,000 original Deere manuals for agricultural, industrial and lawn and garden equipment. Some are very rare and many are hard to find elsewhere.

SSBTractor, P.O. Box 455, Farm-ingville, N.Y. 11738 (ph 631 451-8706; 877 698-3033; [email protected]; www.ssbtractor.com).

SSB Tractor offers an extensive selection of tractor service, repair, shop, parts and owners/operators manuals for almost every make or model of farm tractor. They have an extremely easy to access web page for locating and ordering the manual you want.

Farm Equipment Manual.com, Lee Valley, Inc., 1325 Hwy. 75, Tekamah, Neb. 68061 (ph 402 374-2792; [email protected]; www.farmequipmentmanual.com).

Lee Valley has been collecting farm equipment manuals for over 40 years.

From the archive · Full text
Feature story

Nifty Way To Handle Waste Oil Storage

Featured source:

Nate Regier, Sutton, Alaska, works at a Bible camp in Alaska where he’s in charge of the auto shop. He recently sent FARM SHOW photos of a system he came up with to collect waste oil in the shop.

“I built it mostly from stuff I had laying around and am happy how it turned out. I spent only about $45,” says Regier.

“We burn waste oil for heat, and in the past, handling the oil was always a messy job. We had to carry the oil upstairs by hand and dump it into a storage tank. I wanted an easier way to catch oil with less mess, and to strain the oil for dirt and separate out any water in it.” Regier needed a way to catch used oil under a car lift. He cut off the top one third of a 55-gal. drum to make a big funnel. The funnel mounts on a telescoping pipe on top of a used air compressor. The funnel is equipped with an expanded metal screen and furnace filter that takes out any big chunks in the oil. The oil drains down a 1-in. dia. hose to the air compressor tank through a 1/4-turn ball valve. A clear 1/2-in. dia. hose leads from the compressor tank through a 1/4-ball valve and back to the top of the funnel. It allows air from the compressor tank to escape and also serves as a sight gauge so Regier knows when the tank should be emptied. To empty the air compressor tank, he inserted a 1/2-in. dia. pipe to within 1/4 in. of the bottom of the tank and welded the pipe in place. He attached a hydraulic quick coupler to it, along with an air fitting, pressure regulator, and check valve.

“I bought 30 ft. of service station hose - because it can take light pressure and is oil resistant - and ran it to another room to a waste oil tank,” says Regier.

“There, I run the oil through a filter and into the tank. I leave the coupler on the air compressor tank unhooked until the tank is full, which allows me to wheel the tank around. When I need to empty the tank, I just hook it up to the hose, close the valve to the funnel and sight gauge, and then hook up the air hose to the air coupler.

“I keep the air pressure in the compressor tank set at about 20 psi. It only takes two to three minutes to empty the tank.

“I pull the oil that we use for our heater off the bottom of the storage tank, so I built a frac or separating tank in line before it goes to the pump. This allows me to bleed any water or antifreeze. I like this method better than using a suction tube for the heater because I don’t have to deal with the hassle of a foot valve in the tank.” Contact: FARM SHOW Followup, Nate Regier, 64741 S. Victory Rd., Sutton, Alaska 99674 (ph 907 745-1931 or 907 745-4203; [email protected]).

From the archive · Full text
Feature story

Need A Control Cable? Tewco Can Make It

Featured source: Tewco, Inc.

Need a control cable replaced? Just call Chad Salter, Tewco, Inc. He has no doubt he can assemble about anything you might need. The Tuhill Midwest linkage distributor and factory authorized cable assembler has a $100,000 parts inventory to back it up. Tewco custom builds push-pull, spool valve, brake, clutch, throttle, modulator, shifter and even Unidrum lever cable assemblies. Even better, he can have any cable to you in 24 hours or less.

“If you’re close enough to bring the old cable in, we’ll make it while you wait,” promises Salter.

“If not, we’ll make it and send it out the same day we get it in.”

He knows that when a machine breaks down it’s usually when it’s most needed. He recalls one guy walking in and saying he needed a cable for a machine that was costing him $10,000 a day. Salter says the guy got his cable and his machine up and running.

The company can custom make cables for obsolete controls, as well as for prototypes or even production orders. As a third generation cable man, if Salter hasn’t seen a job before, his father or grandfather probably did.

One of the most unique jobs the company has worked on was for two very rare Tucker automobiles.

“The customer had worked for the company and bought two nearly completed cars off the assembly line when the plant closed,” recalls Salter.

“He asked for a special black sheath on the cable before the end caps were put on, so it would look like the OEM version.”

Other cables made by the company may not be nearly as exotic, but they get the job done. Tewco makes replacements for all the cables on Belarus tractors that are imported into the U.S. Like rubber parts, controls and cables all have to be replaced before the tractors can be sold.

Cables made to release cattle head gates have to have a special coating to protect them from corrosion. The coating increases longevity of the cables by a factor of four.

“We have farmers who find out about us and order 10 cables for themselves and their neighbors,” says Salter.

“Of course we sell single cables by themselves as well.”

Pricing on custom cable work is based on component parts needed. There is no standard pricing sheet. Once a cable is received, the customer is called with an estimate before work begins. That includes special coatings to deal with corrosion.

“Just tell us what you are dealing with, and we’ll tell you what we have to help,” says Salter.

Tewco has the capability to custom assemble based on length and special characteristics or needs. The company has built parachute release cables and throttle cables for top-fuel drag cars and cables for Ferris Wheels.

“The Ferris Wheel cables stretched from the assembly plant through the warehouse,” recalls Salter.

The company also maintains an inventory of other types of linkages - ball joints, clevis joints and other parts.

Contact: FARM SHOW Followup, Tew-co, Inc., 9701 S. 58th St., Franklin, Wis. 53132 (ph 414 423-8080 or 800 558-8730; [email protected]; www.tewco.com).

From the archive · Full text
Feature story

“Slide-Out” PVC Tool Carrier For Skid Loaders

Featured source:

“It lets me bring my tools with me so I don’t have to go looking for them,” says Jim God-bey, Louisville, Ky., who made a “slide out” toolbox that’s designed to fit into the loader arms on his Deere skid loader. The toolbox consists simply of a piece of 4-in. dia. pvc pipe with one side cut out.

“I wanted a safe place to put a few tools on my Deere 325 skid loader, but there was no place to put a regular toolbox that wouldn’t have been in the way. I decided an existing tube hole in the lift arms would work perfect,” says Godbey He started with a 4-in. dia. pvc pipe and glued caps to each end. Then he cut out a section of the pipe big enough to put tools in. He screwed a handle onto one end and a clevis pin to the other. The pin fits into a metal “stop” at one end of the tube hole.

“I’m amazed at how it holds,” says God-bey.

“I use it to carry a grease gun, hammer, needle nose and regular pliers, open end wrenches, 15-in. adjustable wrench, sockets, and extra clevis pins. It’s very secure, too. When the lift arms are all the way down the skid loader’s wheels cover the tube hole so the pipe can’t be removed. It looks nice, too. I painted both ends of the pipe and the tube hole the same yellow color as the skid loader.” Contact: FARM SHOW Followup, Jim Godbey, 2303 S. English Station Rd., Louisville, Ky. 40299 (ph 502 245-1675).