Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 32, No. 3 (2008)

Vol. 32, No. 3 (2008)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

30 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

John H. Bayes

John H. Bayes, Labelle, Fla.

“Here’s how we start a 1940 Buick with a weak battery in the middle of a New England winter: 1. Jack up the left rear wheel and block the chassis so it won’t fall. 2. Pump the gas pedal a couple times. 3. Pull out the throttle a small amount. 4. Put the tranny in 3 gear. 5. Turn the key to the ‘on’ position. 6. Get out of the vehicle and proceed to turn the wheel in a counter clockwise direction. This will turn the engine over and get it started. A little dangerous but it has worked for us several times.”

From the archive · Full text
Reader shop tip

Paul G. Dudley

Paul G. Dudley, Troy, Mo.

A reader in a recent issue said his Troy-Bilt pony garden tiller keeps getting away from him. I have a solution for a ‘kill switch’ that will stop the motor in case you lose control. Here’s how to make one: “Take an old piece of hacksaw blade about 2 in. long. Cut a piece of electrical wire long enough to go from the spark plug over to handle of tiller. Bare both ends of wire. Wrap one end around top of spark plug. Put spark plug wire back onto spark plug. Wrap other end around piece of hacksaw blade. Wrap handle with electrical tape about 1 in. wide and then tape the end of the hacksaw blade with wire on it to the taped handle so it’s insulated from the handle. Leave the other end of the blade laying against the bare metal of handle and bend the end of the blade slightly so it makes good contact. Attach a string to a small piece of leather. Put the leather between the blade and the bare metal of the handle. Tie the other end of the string to your wrist or belt. When the leather is pulled from under the bare end of the hacksaw blade, it will short out the spark plug, killing the motor.”

From the archive · Full text
Reader shop tip

Haskell Rogers

Haskell Rogers, Millerton, Okla.

“Here’s a simple way to make an elastic retainer for long plastic nozzles on aerosol cans. You can buy small retainer rings that do the same thing, but they cost $1 apiece.

“I just use two thin rubber bands. Loop the end of one of the rubber bands around the nozzle, and then loop the other end around the end of the second rubberband. Then slip the second rubber band around around the spray can.”

From the archive · Full text
Reader shop tip

Brian Seckman

Brian Seckman, Weston, W. Va.

“I needed a vented door for a closet where I keep my hot water tank. To save money, I used an ordinary heat register vent and cut a hole the same size as the vent in the door. It worked perfectly and even passed a home inspection. Saved the cost of a special door.”

From the archive · Full text
Reader shop tip

William Townsen

William Townsen, Camden, Tenn.

“I use an electric hoist to raise riding mowers so I can take off the blades to sharpen them or change belts, etc. A simple idea that saves a lot of hassle.”

From the archive · Full text
Reader shop tip

Richard Heimberger

Richard Heimberger, Lucas, Ohio

“I have an old drill press equipped with a table that can be adjusted up or down. The only way to move the unit was by hand, which was difficult to do because the table is heavy and the vise that’s attached to it is even heavier. To make it easier to raise and lower I adapted an old lever-type jack. I made a metal sleeve to go around the post that’s loose enough to slide and then attached the jack to it. Now I can just jack the table to whatever height I want, yet the table is still free to swing in any desired location because it rides loose on top of the sleeve.”

From the archive · Full text
Reader shop tip

Ovalton Rutledge

Ovalton Rutledge, Crystal Springs, Miss.

“We built a steel plate for our forklift that serves as an adjustable work table. We use it to carry parts that have to be cleaned and elevate it to a comfortable working height. There’s a rack on back to stack things against. The forklift tines fit into tapered sleeves, which allows the front edge of the table to lay flat on the ground.”

From the archive · Full text
Reader shop tip

Huskygrip Corp.

Huskygrip Corp., 1820 Production Drive, St. Charles, Ill. ph 877 250-3060; www.huskygrip.com

This company sells a new chain saw sharpener equipped with a soft grip that conforms to your hand. It gives you more control for concentrating the force of each file stroke. Comes with replaceable Vallorbe Swiss files. Sells for $12.95 plus S&H.

From the archive · Full text
Reader shop tip

Elmer Pinkerton

Elmer Pinkerton, Elmwood, Neb.

“I bought a four-post car hoist and erected it outdoors. To do the lifting it uses link speed chains that are exposed to the weather. To lubricate the chains, I mix 80 weight gear oil with an equal amount of gas and apply the mixture with a paint brush. The gas soon evaporates, but the oil remains for several years.

“Caution: don’t use this idea inside a building, because even the best ventilation might not be enough to keep you alive.”

From the archive · Full text
Reader shop tip

Gordon Fuller

Gordon Fuller, Barriere, B.C.

“I built a metal brake that’s shown here putting a 90 degree bend in a 1/4-in. thick, 1 1/2-in. wide strap of steel. For the brake’s push bar, I used the 1 by 6-in. cutting edge off a Caterpillar blade, with a 1 1/2-in. angle iron held on with plates and bolts. It pushes into two angle irons that are welded onto the bottom beam to form a ‘V’. The springs from a pickup hood are used to pull and hold it open. I’ve used this brake to bend 1/4-in. thick, 8-in. wide steel with no problems. It works great.”

From the archive · Full text
Reader shop tip

Al Stober

Al Stober, Leominster, Mass.

“I use a ‘catch cloth’ underneath equipment being repaired to capture dropped parts. A bed sheet works nice. It’ll collect small pieces and prevent them from bouncing or rolling away.”

From the archive · Full text
Reader shop tip

Frank Brinker

Frank Brinker, Johnstown, Ohio

“I store my chains in 5-gal. buckets. Dropping the chains into the buckets and hanging the hooks on the outside edge of the bucket makes the chains easy to retrieve. I also spray paint both ends of each chain the same color so I can easily identify any particular chain at a quick glance. An occasional spray of WD-40 oil down in the bucket helps keep the chains from rusting.”

From the archive · Full text
Reader shop tip

Tom Christensen

Tom Christensen, Blackfoot, Idaho

“Let’s say I have a flat tire but am fairly close to a tire shop. Instead of changing the tire I use an air hose that’s long enough to reach between the flat tire and the vehicle’s spare tire, or any of the vehicle’s other tires. The hose has an air chuck on both ends, so I can take some air out of a full tire and use it to pump up the flat tire. In serious cases, I’ve taken about 10 lbs. of air out of all three other tires so I could inflate the flat tire enough to drive a long ways. I bought a section of hose with threads on each end, and then installed the chuck at each end.”

From the archive · Full text
Reader shop tip

Branson Enterprises

Branson Enterprises, Machesney Park, Ill. ph 815 633-4262; [email protected]; www.bransonenterprises.com)

This company offers magneto and carburetor sales and service. They have most types of carburetors or magnetos in stock, plus parts. Their website provides detailed photos and descriptions with part and model numbers, applications, cross-referencing and more. The website is updated daily. All new and used parts are warranted for 90 days; re-built units are warranted for two years.

Shop feature stories

From the archive · Full text
Feature story

Sawed-Off Vac Blasts Trash

Featured source: James McGowan

A few minutes with a bandsaw can turn any old upright vacuum cleaner into a trash blaster, says James McGowan.

“I was sweeping out the barn, and there’s always lots of stuff the broom just doesn’t get,” he says.

“I thought that if I had a blower, I could really clean up.”

McGowan had an old upright vacuum with a worn out sweeper head. He figured the vacuum blower motor might do the trick. All he had to do was get rid of the parts he didn’t need.

A quick cut with a band saw and he had the handle tip with its switch and the original long electric cord. A little more work and he had the head taken apart and had freed up the blower motor that was already attached to the pipe that formed the upright handle. Another quick cut with the bandsaw, and about a 12-in. section of pipe remained in place at the end of the blower.

“I screwed the switch section to the motor for a handle, reconnected the wires and fired it up,” explains McGowan.

“It’s handy for cleaning out the shop or blowing leaves away from the door of the garage or the side of the barn. It works great anyplace I can reach from an electric outlet.”

Contact: FARM SHOW Followup, James McGowan, 161 Isaac Rd., Russell Springs, Ky. 42642 (ph 270 866-6564).

From the archive · Full text
Feature story

Power Drill Opens Heavy Shop Door

Featured source: Fred Davison

Instead of spending $1,000 to install a door opener for his old shop door, Fred Davison bought a $50 reversible drill and rigged up a pulley system. He simply uses the drill to open and close the 16 by 12-ft. wooden door.

The Highwood, Montana, semi-retired rancher welded a 2-in. pulley on a steel shaft that fits into the drill. The drill turns a belt on the pulley, which is connected to an 11-in. pulley with a 2-in. sprocket on the end. That sprocket connects No. 40 chain to 2-in. sprockets at the bottom and top of the door. Small bolts connect the chain to an iron strap bolted on the bottom of the door to move it up or down when the drill is turned on.

The drill and pulleys are secured and aligned to the shop wall with scrap iron brackets. A rod is also attached to the drill and held in place to maintain the right belt tension.

“You have to make everything in line,” Davison notes, adding he wasn’t sure if pulling the heavy door up on the side would work. But it has worked well for three years.

“It’s just fun to operate. My wife, Kathleen likes it too,” Davison says. Before his drill door opener, the couple pulled the door up by hand with a rope.

With materials and labor costs to install it, Davison estimates the opener cost about $250. He can make plans or kit assemblies available for sale to anyone interested.

Contact: FARM SHOW Followup, Fred Davison, Many Hills Ranch, 1979 Upper Highwood Creek Road, Highwood, Montana 59450 (ph 406 733-5031; [email protected]).

From the archive · Full text
Feature story

Water Shut-Off Tool

Featured source: Gordon Tool Co.

This water shut-off tool fits into tight spots, making it easy to shut off stuck valves.

“It lets you safely turn valves that would otherwise be difficult to turn by hand,” says inventor Bob Gordon.

Made from ABS plastic, the Gordon Wrench measures a little less than 5 in. long by 3 in. wide. The tool has an oval, recessed slot in it that exactly fits over the valve.

“It works great on valves under sinks or toilets that are corroded and almost impossible to turn by hand,” says Gordon.

“After a few years, a shut-off valve can corrode and become nearly impossible to shut off in an emergency or in order to make repairs. If you use a wrench or pliers you’ll often break the valve. The Gordon Wrench grabs the valve’s entire oval handle so there’s no unusual amount of pressure on any point on the valve. And it’s small enough to fit into hard-to-reach areas.

“The wrench also has a second oval slot with a pair of small holes in it. The second oval slot comes in handy wherever there isn’t enough room to turn the wrench 360 degrees with the first oval slot. The holes are for use on valves found on automatic lawn sprinkler systems that are used mainly in California,” says Gordon.

Sells for $9.75 including S&H. Contact: FARM SHOW Followup, Gordon Tool Co., 77500 South 6th St., F-1, Cottage Grove, Oregon 97424 (ph 541 942-9342; [email protected]; www.gordon wrench.com).

From the archive · Full text
Feature story

Bus Front End Revives Old Grader

Featured source: Tom Miller

Instead of spending $2,000 to repair the diesel engine on his 1950’s Austin Weston grader, Tom Miller attached the front end of an old International bus.

“I cut the frame of the bus off right behind the transmission to use the radiator, motor and transmission as a unit,” the Trinidad, Colo., rancher explains.

“The grader’s frame on the rear end slopes down, so I just set this bus unit on the old frame.”

He used his 4-WD Michigan loader to re-move the grader’s diesel engine and radiator and replace it with the bus front. He modified the drive shaft and changed U-joints to make it fit and welded plenty of braces from the grader frame to the bus frame. He re-moved the bus’s air compressor for air brakes and replaced it with the hydraulic pump to operate the grader’s hydraulics.

“The biggest challenge was to connect the linkage from the clutch on the bus to the grader. I also had to work on the throttle linkage,” Miller adds. He notes that between the grader and bus gears - eight altogether - he can drive in super slow speed if needed.

The bus’s V-8 392 cu. in. gas engine has worked well to run the grader. Miller credits the bus’s large radiator for preventing over-heating.

Miller uses the grader to remove snow in the winter and to level the ground along his irrigation ditches and roads throughout his ranch. He purchased the old Army grader many years ago and also picked up the used bus because he wanted its tires for a ranch truck. He transformed the bus body into a woodshop.

“Nothing goes to waste. The old bus put new life into an old grader that wouldn’t have been good for anything,” Miller says.

Contact: FARM SHOW Followup, Tom Miller, 20981 Hwy. 350, Trinidad, Colorado 81082 (ph 719 846-3027).

From the archive · Full text
Feature story

Revolutionary Carbon Foam Batteries

Featured source: Firefly Energy, Inc.

Have you heard about these new 12-volt lead acid batteries that recharge faster, run longer, produce more power, weigh less and are completely recyclable? The “carbon foam” lead acid batteries are so efficient they match the performance of lithium and NiMH batteries without their high cost and also without their safety issues.

The new batteries are being produced by Firefly Energy, a spin-off from Caterpillar. They use Cat’s patented Microcell foam grid technology that replaces up to 70 percent of the lead in a traditional lead acid battery. Positive and negative plates consist of lead oxide slurry impregnated, carbon-graphite foam. The result is up to 50 percent lighter weight than traditional lead acid batteries. The electrodes don’t corrode, operate cooler and resist sulfation.

The carbon foam provides more surface area, which increases power output and enhances recharge speeds. It also improves cold weather performance. Best of all, the foam core improves power availability three to four times when compared to a conventional lead acid battery.

Extended cycle life is also expected for the new batteries. They are projected to last three to five times longer than conventional deep discharge lead acid batteries. The batteries can also be left in storage at low charges for extended periods without damage.

Initial development has been for use in U.S. military vehicles and for over-the-road trucks.

The new Oasis Group 31 batteries developed for deep discharge use, such as truck starting and cab support, are expected to be available this summer.

Other projected markets include hybrid and electric vehicles and specialty equipment such as electric lawn care equipment, electric carts, forklifts, and wheelchairs - any product currently using storage batteries.

The new batteries will not initially be available directly to the general public. Firefly intends to market the technology through existing companies such as Husqvarna, an investor in Firefly.

The first batteries from Firefly were shipped to Husqvarna in November 2007.

Contact: FARM SHOW Followup, Fire-fly Energy, Inc., 5407 N. University St., Ar-bor Hall 2nd Floor, Peoria, Ill. 61614 (ph 309 690-7500; www.fireflyenergy.com).

From the archive · Full text
Feature story

“Wheel-Driven” Generator

Featured source: John Heide

“It lets me operate my generator on diesel, which is much more fuel efficient than gas,” says John Heide, Deerbrook, Wis., about the low cost 7,000-watt generator he powers with a pto and a spare tire.

The generator bolts to the top of a scrap iron frame equipped with 3-pt. mounting brackets. The 15-in. spare tire bolts onto the front part of the frame. Heide uses his Case 530 diesel tractor to pto-drive the tire, which in turn belt-drives the generator.

“The tire serves as a big pulley. It works much on the same principle as Bill Reeks’s wheel-driven bandsaw-type sawmill, on which a 1 1/4-in. wide bandsaw blade is stretched around a pair of 14-in. car tires. Instead of the bandsaw blade I’m running a pair of 1/2-in. wide belts around the tire,” says Heide.

Heide bought the generator at Harbor Freight for $240 and mounted a double groove 4-in. pulley on it. He welded the pto drive system from an Owatonna hay conditioner to the tire’s rim, and also welded a 1/ 2-in. thick steel plate to the back side of the rim. The plate was drilled and tapped, allowing Heide to slide it up and down on a pair of angle iron supports to adjust belt tension.

He used 3/8-in. thick angle iron and 2-in. sq. tubing to build the frame.

“It runs smooth and quiet. It’s surprising how true the double V-belts run on the tire,” says Heide.

“I could’ve used a pulley instead of the tire, but a pulley big enough to do the job would have cost $240. I can also adjust tension on the belt by varying tire pressure.

“By using a diesel tractor to operate the generator instead of gas, I’m saving about 50 percent on fuel costs,” says Heide.

“I had been using a gas engine-powered welder to power another generator, but it used too much fuel. One time the power went out on our farm for three days and it seemed like I was filling up the gas engine every four hours. Now I can fill the tractor up with diesel in the morning and it’ll run all day without a refill.”

Contact: FARM SHOW Followup, John Heide, W8605 Kramer Road, Deerbrook, Wis. 54424 (ph 715 623-6447).

From the archive · Full text
Feature story

He Specializes In Chinese Diesels

Featured source: Robert Shrock

Customers of Imperial Diesel Machinery say their Chinese diesels use less fuel than competitive American and Japanese models.

“One customer told us he was using between 0.4 and 0.5 gal./hr. on his Imperial diesel versus 0.7 to 0.75 gal./hr. on his Yanmar. Both were on 12 K gensets,” says Robert Shrock, Imperial Diesel.

“If you can cut fuel use by a third, that’s a considerable savings at today’s fuel prices.”

Shrock is sold on the Chinese diesels and even powers his business and his home with an Imperial Diesel genset. He filtered cooking oil in the home generators to keep the cost down.

He says the key to satisfaction with Chinese diesels, regardless of the fuel source, is in the prep they receive. He has been import-ing Chinese diesels to repower tractors and for use in gensets for more than 20 years. Although he carries a full line of parts, he has found minimal need for repairs once he learned to “Americanize” them.

“I only sell a couple of parts kits a year to past customers, and we have sold more than 2,000 diesels over the years,” says Shrock. Originally a Belarus tractor and engine dealer, Shrock learned that assembly was often not up to par, though manufacturing quality was fine. When Bellarus engines became difficult to import, Shrock started investigating Chinese diesels.

“My main goal was to supply a value priced product that had equivalent quality to American products,” recalls Shrock.

“I found fac-tories that had good product and metallurgy, but they didn’t pay as much detail to finished assembly.”

He settled on Imperial Diesel Machinery, though they too needed quality control re-view. Americanizing the diesels meant prechecking heat torques and resetting the distance between the cam lobe and the valve stem. He would check all bolts, snugging down and tightening them to proper torque. He would even pull the oil pan and do a bottom up torque check.

“We got rid of most oil and coolant leaks this way,” says Shrock.

“Other importers were just marketing them the way they came. People would blow a head gasket or ruin bearings and cylinders, all because of a lack of initial prep.”

Shrock says the quality control has improved measurably over the years. He no longer pulls the oil pan for a torque check. He also sees less and less need for other prep work. While he did see some water pumps go out after 1,500 to 2,000 hours, that is no longer the case.

“We remachined the housing and put in premium bearings and seals,” says Shrock.

“We don’t have that problem anymore, but we do repair water pumps on other makes.

A big advantage with the Chinese diesels over U.S. brands such as Deere, which Shrock also services, is common parts.

“A lot of parts such as filters, bearings and seals are common between manufacturers.

The one problem that still exists with Chinese diesels is meeting federal emissions mandates. Because they aren’t certified, they can no longer be used to repower tractors and other self-propelled equipment. Shrock says they can be sold for gensets, irrigation pumps and other stationary uses for a few more years.

Contact: FARM SHOW Followup, Imperial Diesel Machinery, 8569 Ward North Rd., Kinsman, Ohio 44428 (ph 330 876-8709).

From the archive · Full text
Feature story

Diesel Boosts Power, Fuel Efficiency In Deere 4020

Featured source: Jim Lumbrezer

Jim Lumbrezer’s Deere 4020 has more power and uses less fuel since he replaced the old gas engine with a diesel.

“The fuel economy is just unbelievable. I used to use 8 to 10 gallons an hour,” says the Swanton, Ohio, farmer.

“Now I use 4 to 4 1/ 2 gallons an hour.” Lumbrezer says there were several challenges to install the 404 diesel engine from a Deere 4230 into his gas-powered 1967 Deere 4020. Because of the size difference of the engines, he had to add a few inches to the frame, which also meant lengthening hydraulic pump lines and steering lines.

One of the biggest challenges was the flywheel.

“The ring gear on the flywheel was different. Instead of buying another flywheel, I took it to a machine shop and had it cut down,” Lumbrezer says.

Using the same flywheel also saved him from making changes to other parts. For the clutch, for example, he just replaced the pilot clutch bearing and clutch disk to match it up to the diesel engine. By changing a bearing, he maintained the dry clutch system in the gas tractor. He also used the alternator and ignition from his old tractor.

Both systems were 12 volt, but Lumbrezer added another battery for more starting power for the 120 hp engine.

“I had to add weight to the back, otherwise it would just spin because of all the power,” he says.

He bought the engine used and spent about $2,000 for everything. That was six years ago, and Lumbrezer says he’s put 2,000 hours on the tractor since then doing fieldwork.

Contact: FARM SHOW Followup, Jim Lumbrezer, 11293 Co. Rd. 2, Swanton, Ohio 43558 (ph 419 825-1089).

From the archive · Full text
Feature story

Seal Stops Drill Bearing Failure

Featured source: Concord Equipment

Tired of replacing bearings on Deere 750 and 1850 No-Till drills? Concord Equipment has the answer with the Seal Sealer.

“The Seal Sealer was developed by a South Dakota farmer who got tired of replacing bearings,” says Shawn Justesen, Concord Equipment.

“I’ve heard from farmers who replace the bearings on their closing wheels every year, sometimes twice a year.”

The closing wheel takes a pounding, working at an angle. Add no-till conditions, and the stress gets worse. The bearing design just doesn’t hold a seal, suggests Justesen.

“Dirt gets in, and the bearing goes out,” he says.

“The Seal Sealer will protect the seal and the bearing, lengthening the life of the bearing.”

Best of all the Seal Sealer takes only minutes to install. Remove the closing wheel, fit the seal sealer over the bearing seal, and put the wheel back on.

Concord Equipment is in the process of finding distributors to handle the product. In the meantime, they’re selling them direct. From one to 15 bearings, the unit price is $24.99. For a limited time, 16 or more Seal Sealers are available at $16 each.

Contact: FARM SHOW Followup, Concord Equipment, 110 15th St. S, Hawley, Minn. 56549 (ph 218 483-3307; fax 218 486-3308; www.concordequipment.com).

From the archive · Full text
Feature story

How To Get Engine Oil Analyzed

Featured source: Larry G. Turner Sr.

Larry G. Turner Sr., of the Oil Analysis Company in Chester, Va., offers a mail order service for vehicle oil analysis. However, his service has an added twist from others.

“The unique part of my service is that I also maintain a statistical database of all vehicles so you’ll be able to see what you and other owners of similar vehicles are experiencing at a similar mileage, plus the brand and type of oil used, engine type, etc.,” he says.

“A lot of customers really like that.”

Turner makes the analogy that an oil analysis kit is like a blood test for your car, since it lets you see if the engine’s healthy (wearing normally). It identifies specific contaminants which helps to pinpoint the cause of a problem before more expensive repairs become necessary.

You no longer have to wonder if the oil you’re using is providing the kind of protection your valuable engine needs, or if that expensive engine rebuild you just paid for is wearing normally, he explains.

“This is a predictive maintenance program that needs to be done as often as you’d perform a tune up, or any regularly scheduled preventative maintenance,” he says.

“Although it’s offered primarily for analysis of engine oil, this program will also provide the same warning system for transmissions, steering gear, transaxles, and other lubricated components.”

A few examples of analysis results include: elevated chromium, which means increased piston wear; elevated copper means bearing wear; presence of silicone means worn seals or air filter; elevated iron means cylinder wear or ring damage; and glycol presence means a leaking head gasket.

The oil analysis kits include instructions and all supplies needed to collect and submit the sample, such as a sample bottle and label, prepaid mailer, mailing label and information form. The form, to be completed by the customer, asks for certain information about the oil being tested and about the vehicle.

To make the collection process as easy as possible, Turner also offers a bellows bottle, which allows the oil to be extracted through the dipstick tube, using tubing that’s provided. Alternatively, a standard bottle is used to catch a sample while the oil drains.

Preliminary test results are sent by email, usually in a week to 10 days from the sample being mailed in. Soon after, Turner supplies a hard copy with additional details from the lab, by U.S. mail. The analysis provides a breakdown of contaminants, additives, and physical properties of the oil, along with an interpretation and advice/suggestions regarding abnormal results.

“If you’d like to review the database of previous oil sample reports, please visit http:/ /members.rennlist.com/oil and select Test Results. There, you’ll see over 200 Analysis Reports prepared for our customers. Additionally, there are four samples of new, unused oil, which provide a baseline for those who wish to know the sample values of their oil before it’s been subjected to the stresses of an engine. These sample reports are high-lighted with green bands of color to make them easy to find.”

The kit costs $19.99 plus S&H, but because he encourages a regular checking program, Turner offers a 3-pack oil sample kit for $55 plus S&H. There are no additional lab fees, as the kits are all-inclusive.

Besides these test kits, Turner also sells several useful chemical products such as an odor eliminator, adhesive remover, zinc phosphate rust preparation for metal parts, and body seam sealer.

Contact: FARM SHOW Followup, The Oil Analysis Company, 4608 Dunkirk Drive, Chester, Va. 23831 (ph 800 583-8601 or 804 526-1151; [email protected]; www.youroil.net).

From the archive · Full text
Feature story

“Doubled Up” Tools Handy, Save Space

Featured source: Hugh Craft

Hugh “Buz” Craft of Wills Point, Texas, re-cently sent FARM SHOW photos of several “doubled up” tools he made by bolting or welding two tools together.

Some example of his doubled-up tools include: A screwdriver combination with a flat head on one end and a Phillips head on the other; claw hammer and ball peen; brass mallet and rubber mallet; kitchen broom and shop broom; hoe and rake; scrub brush and rubber scraper; egg beater and oval whip; weed chopper and spike; fork and hamburger flipper for grilling; flat wire brush and round “reaming” brush; spaghetti claw and serrated plastic knife; large cook-out spoon and fork; and paring knife and ice pick.

“The handiest doubled-up tool in my collection is my Phillips/flat head screwdriver set because it’s so easy to see, even in a cluttered-up toolbox. As soon as I spot the handle, I know I’ve got the right screwdriver point without having to do a lot of digging,” says Craft.

To put two tools together, most of the time he drills a hole in the handle on one of the tools and then bolts or screws them together.

“To double up the screwdrivers, a friend cut two inches off the plastic handle of both screwdrivers to expose the metal rods inside, then welded the two handles together and wrapped tape around them,” says Craft.

Contact: FARM SHOW Followup, Buz Craft, P.O. Box 565, Wills Point, Texas 75169 (ph 903 873-2367; [email protected]).

From the archive · Full text
Feature story

“Sled” Makes Blade Sharpening Easy

Featured source: Tim Queeno

Tim Queeno’s woodworking bench is filled with sharp chisels and planes thanks to his Sharpening Sled, which was the result of eight years of making prototypes. The end result worked so well he started making them for sale.

Most sharpeners have complicated setups that require measuring how much of the blade protrudes to achieve the correct angle, Queeno says. The Lima, N.Y. inventor’s sharpener has four simple setup steps.

1) Loosen the black handles and set the desired bevel angle using the precise, laser engraved index marks. Tighten the handles.

2) Place the Sharpening Sled over the sharpening stone.

3) Insert the chisel blade and push the alignment slide against the side of the blade to ensure it is square in the sled.

4) Tighten the brass toggle foot clamp on top to secure the blade.

Then just move the sled back and forth over the stone until the blade is sharpened. To add a micro-bevel for added strength, increase the angle by 5 degrees and make a couple more swipes on the stone.

“The novelty of the design is that it straddles the sharpening stone,” Queeno says.

“The advantage is you use the whole stone, instead of just part of it, so it’s very efficient.”

The sharpener has settings for 5 to 60-degree angles, four sealed radial bearings for rollers, and accommodates blades up to 3 in. wide and 1/4 in. thick.

Queeno makes some of the parts, hires local shops for other parts, and his family assembles the sharpeners in his farm’s barn. While the Sharpening Sled is more expensive than sharpeners available at box stores, it’s a tool that can be handed down for generations along with woodworking tools, he says. Three sizes are available, ranging from $69.99 to $79.99. Queeno offers a variety of other woodworking products through the internet. He’s looking for dealers.

With the popularity of his sharpening tool, Queeno started a home-based business, Alisam Engineering - using a conglomera-tion of his three children’s name for the business name. He offers a variety of accessories for woodworkers and home machinists, selling them on his website, eBay and through Hartville Tool. Queeno will mail out brochures of his products and is also interested in talking to dealers.

Contact: Tim Queeno, Alisam Engineering, Box 75, Lima, N.Y. 14485 (ph 585 624-2280; [email protected]; www.alisam.com).

From the archive · Full text
Feature story

Repair Patch Fits Deere Mower Decks

Featured source: Sunsdahls’ Restoration Tooling

Instead of replacing worn mower decks, owners of Deere lawn and garden tractors can purchase a deck patch.

“It reinforces the area where the mower collects moisture from grass and starts to rust out or crack,” says Dick Sunsdahl of Sunsdahls’ Restoration Tooling in Faribault, Minn.

“Mower decks are expensive to replace. This is a low cost alternative.”

Sunsdahl’s son and business partner, Thad, invented and designed the computer- designed, laser-cut, 12-gauge steel patch. The Sunsdahls’ hobby shop specializes in designing, marketing and making tools and parts to service and restore Deere products.

The patch fits mowers built from 1963 to 1987 in LGT models 110, 112, 120 and 140, and 200 and 300 series. It comes in two sizes. The smaller size fits decks 36 to 39 in. The larger size fits decks 40 in. and up.

To install the patch, unbolt the bearing housing and blade, and line up the three patch holes with the bearing’s bolt holes. Since that is the deteriorated area that needs patching, most people weld or rivet the patches to the bottom of the mower, Sunsdahl says.

“The patch fits into the recess of the mower deck so it fits secure,” he adds.

Since the Sunsdahls started selling the patch a couple of years ago, they’ve had re-peat customers, Sunsdahl says. For example, one customer was uncertain how well it would work, so he bought just one. Later, he ordered two more.

At just $28 (plus $10 shipping) apiece, the patches add years of working life to the mower, Sunsdahl notes.

Contact: FARM SHOW Followup, Sunsdahls’ Restoration Tooling, 1703 Green-wood Place, Faribault, Minn. 55021 (ph 507 334-8966; [email protected]; www.sunsdahltooling.com).

From the archive · Full text
Feature story

Simple Boxes Hold Debris And Tools

Featured source: Pete Peters / Pete Peter

When Pete Peters finds a rock while mowing, he tosses it into a cargo carrier he built for the back of his mower.

The Osler, Sask., man built a simple 12 by 12 by 10-in. box out of tin and slipped it into an angle iron frame welded to two flat iron arms that fit holes on the tractor’s frame next to the hitch.

“It can be mounted or removed in just seconds with brackets that hook to the frame,” Peters says.

He uses the same technique to support a small toolbox - an old tin box he found. He keeps extra fuses, wrenches, screwdrivers and pliers in the box for simple repairs.

Spray painted Deere green and finished off with Deere decals, the boxes look like they belong on the lawn tractor.

Peters says he may be interested in making the boxes for others if there’s interest.

Contact: FARM SHOW Followup, Pete Peter, P.O. Box 166, Osler, Sask., Canada S0K 3AO (ph 306 239-2045).

From the archive · Full text
Feature story

Safety Tip For Hand Drills

Featured source: Tom Christensen

A bad experience led Tom Christensen of Blackfoot, Idaho, to come up with a safety tip he wanted to share with FARM SHOW readers.

“I broke my big 1/2-in. side angle drive drill but the damage could have been pre-vented if I had thought of this idea sooner,” he says.

“Maybe I can prevent other broken drills and even some broken wrists.”

The problem he’s talking about is when a drill bit binds up and the drill itself starts spinning in your hands.

The solution is to plug the drill into an extension cord and then stand on the end of the cord, adjusting the length of the drill cord in your hand so that when the drill starts to counter rotate, it will unplug itself immediately.”

Contact: FARM SHOW Followup, Tom Christensen, 178N 685W, Blackfoot, Idaho 83221 (ph 208 684-3601 or 208 680-5095 (cell); [email protected]).