Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 24, No. 6 (2000)

Vol. 24, No. 6 (2000)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 40–42

28 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Chris Cole

Chris Cole, Surplus Center, Box 82209, Lincoln, Neb. 68501 (ph 800 488-3407)

“Our new hydraulic-operated pto drive motor operates off tractor hydraulics and can be used to shaft-drive equipment that doesn’t have a pto. It can also provide power in remote applications. You can use it on a tractor that already has a pto to provide a second pto. If your tractor doesn’t already have a pto you can use tractor hydraulics to drive the motor. Even if the tractor does have a pto, you can mount the hydraulic-operated motor directly on an implement and not have to use the pto shaft.

“The motor can be used to operate augers, mowers, or any other equipment that requires a 28 hp or less tractor. One advantage of our motor is is that it’s safer to use hydraulics than a rotating pto shaft. The motor comes with a mounting flange that can be bolted to a steel plate. Sells for $289.99 plus S&H.”

From the archive · Full text
Reader shop tip

Jerry L. Benny

Jerry L. Benny, Chadron, Neb.

“When making fence H-braces, I use big spikes to hold the posts. There’s no need to notch the posts. I just drill a 1/2-in. dia. hole and cut off the head of the spike. I’ve used this idea successfully for 25 years.”

From the archive · Full text
Reader shop tip

Eugene G. Lewis

Eugene G. Lewis, Corfu, N.Y.

“I couldn’t reach the grease fitting on my MC flail mower without having to remove the bar guard. To solve the problem, I extended the grease fitting with a length of tubing.”

From the archive · Full text
Reader shop tip 1 of 3

Dave White

Individual tip 1 of 3 from this reader’s published contribution.
Dave White, Farmersville, Ill.

“A 3-wheeled TV dolly that I bought at an auction makes a handy work stand. I bought it at an auction for $10. It’s equipped with a telescoping yoke on top that was originally used to hold the camera. I use the yoke to hold one end of a 20-ft. length of angle iron or a long 2 by 4, and rest the other end on my work bench. It’s easy to raise or lower the yoke to match the height of the bench. The yoke can be raised from 2 1/2 to 4 ft. high.

The dolly is equipped with a steering wheel on front that guides the rig’s three wheels in any direction. The unit spins around on a dime.

From the archive · Full text
Reader shop tip 2 of 3

Dave White

Individual tip 2 of 3 from this reader’s published contribution.
Dave White, Farmersville, Ill.

“I used the axle housing from one side of a Deere tractor to make a handy and portable work bench. The axle housing serves as the base. I welded a round piece of 1-in. thick steel plate to the bearings on top of the axle.

I bolted a vise onto one side of the table and use it to ‘lock’ an object in place, such as a length of angle iron, so that I can cut it. Works great when used together with my TV dolly. The round plate spins freely and will automatically line the vise up with the dolly.

From the archive · Full text
Reader shop tip 3 of 3

Dave White

Individual tip 3 of 3 from this reader’s published contribution.
Dave White, Farmersville, Ill.

“I bought a used 4-wheeled utility cart at an auction and mounted my air compressor on it. Works great for sandblasting and painting and operating air tools such as big impact wrenches. The cart is high enough off the floor that I can use a forklift to pick it up and move it around.”

From the archive · Full text
Reader shop tip

Eugene Gulgren

Eugene Gulgren, McHenry, Ill.

“I replaced the original front wheels on my push mower with a pair of small adjustable caster wheels. The caster wheels make it a lot easier to trim grass around yard fixtures such as benches, fence posts and under shrubs. I used short lengths of 2-in. angle iron to attach the wheels to the mower frame. One side of the angle iron was cut away to provide an upright which I attached to the mower frame. I fastened the wheels to the other side of the angle iron. The mower’s original wheels were adjustable for height, and so are the caster wheels.”

From the archive · Full text
Reader shop tip 1 of 3

Steve’s Heavy Equipment & Diesel Service

Individual tip 1 of 3 from this reader’s published contribution.
Steve’s Heavy Equipment & Diesel Service, 15830 Carver Highlands Drive, Carver, Minn. 55315 ph 952 448-2429; Website: www.skidsteerstuff.com)

“Our anti-theft switch kit for skid steer loaders interrupts the circuit to the electronic solenoid that activates the fuel pump. The engine turns over but won’t start. Works on diesel models only. The kit consists of connectors that plug into the existing wiring. It works better than other anti-theft wiring kits which mount between the battery cables and completely disable the engine, because the thief knows he can still use the vehicle’s master switch to start the engine. Sells for $52 to $68 plus S&H depending on the skid steer model. Also works on some tractors.

From the archive · Full text
Reader shop tip 2 of 3

Steve’s Heavy Equipment & Diesel Service

Individual tip 2 of 3 from this reader’s published contribution.
Steve’s Heavy Equipment & Diesel Service, 15830 Carver Highlands Drive, Carver, Minn. 55315 ph 952 448-2429; Website: www.skidsteerstuff.com)

“Our door protection kit for skid steer loaders is designed to shut off the machine’s loader controls whenever the door is open. Keeps the loader from accidentally ripping off the door. The kit consists of connectors that plug into the wiring between the lap bar lock switch and a switch mounted on the door. It’s designed for all late-model Bobcat, New Holland, Case and Cat brands. Sells for $42 to $54 plus S&H, depending on the skid steer model.

From the archive · Full text
Reader shop tip 3 of 3

Steve’s Heavy Equipment & Diesel Service

Individual tip 3 of 3 from this reader’s published contribution.
Steve’s Heavy Equipment & Diesel Service, 15830 Carver Highlands Drive, Carver, Minn. 55315 ph 952 448-2429; Website: www.skidsteerstuff.com)

“We also sell a first-of-its-kind safety mirror for skid steer loaders. The 14-in. long, 4-in. high mirror has a convex shape and is designed to mount directly in front of the operator for unobstructed entrance and exit. It bolts to the overhead safety cage. A knob is used to adjust the mirror up or down. Con-ventional side mirrors can’t be mounted on skid steer loaders because the loader arms are in the way. The mirror’s convex shape gives you a great field of vision, with no blind spots. Sells for $90 plus S&H.”

From the archive · Full text
Reader shop tip 1 of 2

Clair and Warren Wilson

Individual tip 1 of 2 from this reader’s published contribution.
Clair and Warren Wilson, Winchester, Ill.

“We get a lot of use out of this portable 4 by 5-ft. work table, which was simple to build. A sheet of 3/4-in. thick plate steel makes up the table top. Lengths of 4-in. sq. box steel, with small wheels at the bottom, were welded directly to the table top to make the legs. There is no additional bracing. There’s a drawer on one side of the table and brackets at both ends for holding squares, clamps, bars, etc. We do a lot of fabricating and have a series of cranes along our shop ceiling. We use the cranes to set objects on the table for repairs. We can even weld stuff that we want to repair right on top of the table. When we’re done welding we just cut the part off and grind the welding material back down to make the table smooth again. Also, we cut holes into the table for hold-down bolts.

From the archive · Full text
Reader shop tip 2 of 2

Clair and Warren Wilson

Individual tip 2 of 2 from this reader’s published contribution.
Clair and Warren Wilson, Winchester, Ill.

“A few years ago I tore down a building at a local state hospital and got a wall-mounted, 3-phase electric fan free. I mounted the 48-in. dia. fan, which has only two blades, inside a 52-in. sq. metal box which I mounted on wheels. The fan turns very slow so it’s quiet. However, it pushes a tremendous amount of air. It’ll push air a distance of 100 ft. and helps keep our shop cool on hot, still days.”

From the archive · Full text
Reader shop tip

A. Sanders

A. Sanders, Bangor, Sask.

“I had a number of broken bolt studs that broke deep in a casting. I couldn’t get a drill bit or even a center punch to stay put in the center of the stud. I solved the problem by drilling a hole slightly smaller than the stud all the way through the center of another bolt and tap threads into the casting to screw in the bolt. Then I slip a drill bit in through the bolt and drill out the stud. The bolt stays firmly in place and keeps the drill centered exactly so that it doesn’t ‘wander’ and damage the threads in the casting. This idea won’t work if the stud breaks flush because you couldn’t thread the bolt into the casting. I made a set of different size bolts with different size holes ranging from 1/4 to 3/4 inches in diameter.”

From the archive · Full text
Reader shop tip

John Aaron Rissler

John Aaron Rissler, New Enterprise, Pa.

“Needing both a tool chest and a work bench, I decided to combine both by building what I call a Tool Bench. I needed all sizes of drawers – wide and narrow, deep and shallow. I used sq. steel tubing to make the frame and angle iron to make the drawer slides. I didn’t really count the drawers but just figured the different sizes I wanted.

“I sized the bench so that a 4 by 8-ft. sheet of 3/4-in. plywood would fit as a top. I ended up with 53 drawers and an upper deck work area designed for work on smaller tools and projects. There are 2-ft. long drawers on both sides. I also fitted in space for four large drawers for hanging file folders. At this time, some of the drawers are still empty, but that’s the way I wanted it - better to have too many drawers than not enough. With plenty of drawers my special tools now have their own places.

“The work bench stands 31 in. high. It’s big enough that we can get a whole engine up on it, or even two, with room to sort out parts and work on them.

“My total cost for lumber and steel was about $200. A commercial toolbox with only half that many drawers costs three times as much and doesn’t offer the work bench area.”

From the archive · Full text
Reader shop tip

David C. Prause

David C. Prause, China Spring, Tex.

“When the wind is blowing, the gathering wheels on my Vermeer baler don’t work. I solved the problem by taking car seat cover material and completely covering the tongue of the baler, one piece on each side with wire back to the baler. This lets me bale in a strong wind, especially with light coastal hay. I tie it up off the ground a few inches so the windrow slides underneath.”

From the archive · Full text
Reader shop tip

Al Stober

Al Stober, Ledminster, Mass.

“Rubber canning jar seals work excellent to stop arterial bleeding when dehorning cattle. Just leave a short horn stump and stretch the rubber seal around the two stumps. It acts like a very strong elastic band. It’s best done when flies are not a problem and best to also use a powder to help control bleeding and infection.”

From the archive · Full text
Reader shop tip

Donald Enterline

Donald Enterline, Jamestown, Penn.

“One idea that works well for me is a method I use to lock nuts in place. After you put a nut on, just hammer the end of the bolt a couple times with hammer, hard enough to flatten it slightly. That’ll hold the nut in place so it can’t come off.”

From the archive · Full text
Reader shop tip

Woody Stewart

Woody Stewart, Rockglen, Sask.

“To seal windows on older vehicles with lots of air leaks, grease the edges of the window and then fill the track with silicone and run the window up. The silicone will seal tightly around the window but will not stick. Once the silicone sets, you can wipe off the grease and you’ll have a tight seal.”

From the archive · Full text
Reader shop tip

William E. Erickson

William E. Erickson, Ellensburg, Wash.

“I use a pair of 4 by 4’s connected by a threaded rod to make easy-to-use wheel chocks for tandem axle trailers. The boards put pressure between the two tires to keep them from moving. First, I determined where I wanted the blocks and then cut their ends to fit the curvature of the tires. Then I drilled a hole through the middle of each 4 by 4 and measured to see how long the rod would need to be, allowing room for a nut and washer at the bottom and a coupler nut and a washer on top. I use an open-end wrench to tighten the blocks.

“I use the same wheel chock idea on my 22-ft. fifth wheel RV trailer. These chocks can’t slip out of place like an ordinary chock that’s placed under the tire. And they’re inexpensive to make.”

From the archive · Full text
Reader shop tip

Norman Epp

Norman Epp, Hillsboro, Kan.

“I made a leak-checking water tank for car and pickup tires by cutting down a tractor tire and setting it on top of a pickup tire that’s laying flat on the ground. I cut up the tire with a carbide blade in a circular saw to cut the tire, and a metal cutting blade to get through the bead.

From the archive · Full text
Reader shop tip

Walt Austin

Walt Austin, T90, Wash.

“I used to use a pressure washer to clean out dirt between planks on bridges. It was a messy job. Then I got the idea of using a crosscut power saw. I just run it between the plans and it gets the job done quick and easy. Works great.”

From the archive · Full text
Reader shop tip

Cliff Brandenburger

Cliff Brandenburger, BeecherCity, Ill.

Cliff put a flourescent light on a track above the work area in his shop so he can position the light exactly where he needs it. He first suspended a 2 by 6 vertically. Then he made a “track” by nailing 1-in. boards to either side of the bottom of the 2 by 6. He made U-shaped hangars for the light out of strap iron. He put roller bearings on the upper ends of the strap iron to roll along the track.

Shop feature stories

From the archive · Full text
Feature story

Cam Box Makes Engine Overhaul Easier

Featured source:

How many times when overhauling an engine have you drilled holes in a piece of wood to keep lifters in proper order during overhaul, only to wonder later which end of the wood is supposed to be the front of the motor.

That problem is why Wetherell came up with its “Little Red Cam Box” which keeps lifters in proper order during overhaul. It also protects the cam and lifters during shipping or storage.

Sells for $29.95 plus S & H. Contact: FARM SHOW Followup, Wetherell Mfg. Co., Cleghorn, Iowa 51014 (ph 712 436-2266; fax 712 436-2672).

From the archive · Full text
Feature story

Air-Operated Lift Table Handles Up To 1,000 Lbs.

Featured source:

“I thought your readers might like to know about this great lift table,” says Kevin Johansen, Mound, Minn., who recently emailed FARM SHOW to tell us how much he likes his new air-operated lift table.

“It may be a little expensive but it’s by far the best lift table I’ve ever seen. I’m a mechanical engineer and I’m impressed with its sturdiness. The fit and finish are also excellent. It lets me work on garden tractors, ATV’s, motorcycles, and snowmobiles without having to stoop or bend down.”

Built by Handy Industries of Marshalltown, Iowa, the Handy Air Lift has a 24 by 80-in. steel table and a scissors lift that’s powered by a pneumatic cylinder. The cylinder operates off any air compressor that can deliver 90 to 100 psi. A foot-operated valve is used to raise or lower the table. The entire unit weighs just 350 lbs. but has a lifting capacity of 1,000 lbs. It raises to a working height of 30 1/4 in. When lowered, it’s only 7 in. high allowing for easy on-off loading.

Contact: FARM SHOW Followup, Handy Industries, L.L.C., 702 S. 3rd Ave., Marshalltown, Iowa 50158 (ph 800 247-7594; fax 641 752-1205; Website: www.handyindustries.com).

From the archive · Full text
Feature story

Washing Machine Sand Blasting Cabinet

Featured source:

After using commercial sand blasting cabinets for years, Bruce Graham knew their shortcomings – dust that causes poor visibility, poor lighting, difficult-to-maintain filters, and expensive and difficult-to-change media. He avoided most of those problems when he built his own sand blaster out of a top-loading washing machine.

Graham made an angle iron framework and set the stripped-down washing machine case in it on its side at a 35 degree angle. He used galvanized sheet metal to close off the top and bottom of the washing machine (which are now the sides). On one side he left a large removable half section on to serve as an access door. Two large windows were cut out of the top and front-facing sides and 1/4-in. thick glass panes inserted in them. A clamp-style floodlight mounts directly against one window.

He cut a pair of 7-in. dia. holes, spaced 16 in. apart, in the front of the cabinet and attached industrial quality rubber gloves inside them. He cut a 2-in. wide opening in the bottom of the cabinet along its entire length, allowing heavy particles to fall through a galvanized steel funnel and into a hopper. A large kitchen strainer mounted across the top of the hopper traps any debris or parts that might fall through the edges of the grating.

Inside the cabinet is an expanded steel grating laid across four 1-in. angle iron supports. A piece of 1/4-in. sq. hardware cloth on top of the grating prevents small parts from falling through.

To suck dust out of the cabinet, he closed off both sides of an old furnace blower and mounted it on the shop wall about 2 ft. above the sand blaster. The blower is activated by flipping a switch on the cabinet. A 6-ft. length of 4-in. dia. flexible hose runs from the blower down to the sand blaster and sucks out light dust particles, blowing them outside the shop through an opening in the wall. A pair of automotive breather units keep the suction caused by the blower from breaking the glass windows.

“I’ve had very few problems with it,” says Graham.

“I spent about $250. Commercial units of comparable size sell for about $1,000.

“The blower does a great job of removing dust. It pulls enough air through the cabinet to keep the area around the cabinet relatively dust-free. At first I used a canister-type shop vacuum cleaner to suck out dust. However, it was noisy and dirty and tended to clog up. I use inexpensive playground sand to do the cleaning. I sift the sand through a standard window screen sieve as I fill the hopper and discard any larger pebbles that might plug up the unit.

“The blower is much quieter than most commercial vacuum units. These types of blowers are available from junk dealers for little or nothing. The blasting gun I use is an older Craftsman model that has a replaceable ceramic tip.”

Graham used wooden frames to install the windows, mitering a groove in the wood that’s the same thickness as the glass.

“The grooves make it easy to replace the glass,” notes Graham.

Contact: FARM SHOW Followup, Bruce Graham, 13801 Eastside Rd., Tyler, Texas 75707 (ph 903 566-1248; E-mail: [email protected]).

From the archive · Full text
Feature story

“Oil Vac” Made From Milker Vacuum Pump

Featured source:

A used milker vacuum pump, belt-driven by an electric motor, makes a dandy “oil vacuum” for sucking oil out of engines, transmissions, and gearboxes, says John Rissler, New Enterprise, Pa.

“It was cheap to build and helps keep my shop neat and clean,” says Rissler.

He bought the vacuum pump cheap from a local dairy farm and mounted it along with a new electric motor on a 10-gal. tank that oil drains into. The tank mounts on a steel frame outside Rissler’s shop.

Rissler drilled a hole in one end of the tank, then welded a pipe fitting into it. A 1/2-in. dia. plastic hose attaches to the fitting and runs inside the shop through the shop wall. There’s a 2-ft. length of 1/4-in. dia. copper tubing that serves as a suction wand. To suck out oil, Rissler inserts the wand directly into the engine dipstick tube.

The vacuum pump is also plumbed into the end of the tank to create suction. Once the tank is full, oil gravity-flows out a drain plug at one end of the tank and into a 55-gal. barrel for disposal.

Rissler farms and also operates a business selling and servicing small engines and lawn mowers.

“I use it to change engine and transmission oil and to remove excess oil when too much was added to an engine. It also works great for repriming hydrostatic transmissions. I just stick the tube into the return line and work the valve until the oil comes through.

“I flip a switch inside the building to start the motor. It’s a lot quicker than draining oil the conventional way and also much cleaner. I can make adjustments, sharpen blades, etc., while draining the oil without having to watch it all the time.

“I paid about $100 for the motor and $55 for the vacuum pump. My total cost was less than $250. Commercial units on the market sell for $1,000 or more.

“The small vacuum pump I used is no longer commonly used by dairies because most dairy operations now run more than three milkers. As a result you can buy them cheap.”

Contact: FARM SHOW Followup, John Aaron Rissler, 3409 Brumbaugh Rd., New Enterprise, Pa. 16664 (ph 814 766-2117).

From the archive · Full text
Feature story

“Oil Caddy” Built Out Of Discarded Barbecue

Featured source:

Old propane barbecue grills can be used to make handy, inexpensive oil caddies, says Kevin Sproule of Taber, Alberta, who sent FARM SHOW photos of the portable oil caddy he made for use around his shop.

“It makes it easier to keep my shop neat and clean. I already had the grill so my total cost was less than $10,” says Sproule.

He disassembled the grill, throwing away the entire bottom part but keeping the lid, rack, and control panel. He turned the lid over and mounted it inside the grill frame at a slight angle. He tapped a 1/2-in. ball valve into the lower end and set the grill’s two cooking racks inside the lid.

“It works great for draining the oil from our Steiger tractors,” says Sproule.

“The grill is only 3 1/2-ft. high so I can wheel it right under the tractor. I keep two 5-gal. pails on the base and a 2 1/2-gal. pail on the side. The lid holds about 3 1/2 gallons. When the lid is almost full I open the valve to let the oil drain into one of the pails. When I’m done I set the old filter on the racks to let it drain completely.

“I screwed a piece of plywood onto one side of the grill which I use to hold oil jugs. When I drain oil from my combine, I hang a 5-liter plastic jug from a hook that’s attached to the plywood. The combine has a cannis-ter-style filter that has to be separated. The cannister drips oil down into the jug.

“I removed the switches and ignitor from the control panel and screwed the panel to the top inside edge of the lid. I stick funnels through the holes in the panel.”

For more information, contact: FARM SHOW Followup, Kevin Sproule, Box 4143, Taber, Alberta, Canada T1G 2C6 (pg 403 223-4052).